diff options
Diffstat (limited to 'docs/system')
| -rw-r--r-- | docs/system/arm/mps2.rst | 24 | ||||
| -rw-r--r-- | docs/system/arm/nuvoton.rst | 3 |
2 files changed, 20 insertions, 7 deletions
diff --git a/docs/system/arm/mps2.rst b/docs/system/arm/mps2.rst index 8c5b5f1fe0..601ccea15c 100644 --- a/docs/system/arm/mps2.rst +++ b/docs/system/arm/mps2.rst @@ -1,12 +1,15 @@ -Arm MPS2 boards (``mps2-an385``, ``mps2-an386``, ``mps2-an500``, ``mps2-an505``, ``mps2-an511``, ``mps2-an521``) -================================================================================================================ +Arm MPS2 and MPS3 boards (``mps2-an385``, ``mps2-an386``, ``mps2-an500``, ``mps2-an505``, ``mps2-an511``, ``mps2-an521``, ``mps3-an524``) +========================================================================================================================================= These board models all use Arm M-profile CPUs. -The Arm MPS2 and MPS2+ dev boards are FPGA based (the 2+ has a bigger -FPGA but is otherwise the same as the 2). Since the CPU itself -and most of the devices are in the FPGA, the details of the board -as seen by the guest depend significantly on the FPGA image. +The Arm MPS2, MPS2+ and MPS3 dev boards are FPGA based (the 2+ has a +bigger FPGA but is otherwise the same as the 2; the 3 has a bigger +FPGA again, can handle 4GB of RAM and has a USB controller and QSPI flash). + +Since the CPU itself and most of the devices are in the FPGA, the +details of the board as seen by the guest depend significantly on the +FPGA image. QEMU models the following FPGA images: @@ -22,12 +25,21 @@ QEMU models the following FPGA images: Cortex-M3 'DesignStart' as documented in Arm Application Note AN511 ``mps2-an521`` Dual Cortex-M33 as documented in Arm Application Note AN521 +``mps3-an524`` + Dual Cortex-M33 on an MPS3, as documented in Arm Application Note AN524 Differences between QEMU and real hardware: - AN385/AN386 remapping of low 16K of memory to either ZBT SSRAM1 or to block RAM is unimplemented (QEMU always maps this to ZBT SSRAM1, as if zbt_boot_ctrl is always zero) +- AN524 remapping of low memory to either BRAM or to QSPI flash is + unimplemented (QEMU always maps this to BRAM, ignoring the + SCC CFG_REG0 memory-remap bit) - QEMU provides a LAN9118 ethernet rather than LAN9220; the only guest visible difference is that the LAN9118 doesn't support checksum offloading +- QEMU does not model the QSPI flash in MPS3 boards as real QSPI + flash, but only as simple ROM, so attempting to rewrite the flash + from the guest will fail +- QEMU does not model the USB controller in MPS3 boards diff --git a/docs/system/arm/nuvoton.rst b/docs/system/arm/nuvoton.rst index 34fc799b2d..f9fb9224da 100644 --- a/docs/system/arm/nuvoton.rst +++ b/docs/system/arm/nuvoton.rst @@ -44,6 +44,7 @@ Supported devices * Analog to Digital Converter (ADC) * Pulse Width Modulation (PWM) * SMBus controller (SMBF) + * Ethernet controller (EMC) Missing devices --------------- @@ -57,7 +58,7 @@ Missing devices * Shared memory (SHM) * eSPI slave interface - * Ethernet controllers (GMAC and EMC) + * Ethernet controller (GMAC) * USB device (USBD) * Peripheral SPI controller (PSPI) * SD/MMC host |