diff options
Diffstat (limited to 'hw/arm')
| -rw-r--r-- | hw/arm/armsse.c | 49 |
1 files changed, 31 insertions, 18 deletions
diff --git a/hw/arm/armsse.c b/hw/arm/armsse.c index 6eed2ecf80..76cc690579 100644 --- a/hw/arm/armsse.c +++ b/hw/arm/armsse.c @@ -11,6 +11,7 @@ #include "qemu/osdep.h" #include "qemu/log.h" +#include "qemu/bitops.h" #include "qapi/error.h" #include "trace.h" #include "hw/sysbus.h" @@ -29,6 +30,7 @@ struct ARMSSEInfo { int sram_banks; int num_cpus; uint32_t sys_version; + uint32_t cpuwait_rst; SysConfigFormat sys_config_format; bool has_mhus; bool has_ppus; @@ -43,6 +45,7 @@ static const ARMSSEInfo armsse_variants[] = { .sram_banks = 1, .num_cpus = 1, .sys_version = 0x41743, + .cpuwait_rst = 0, .sys_config_format = IoTKitFormat, .has_mhus = false, .has_ppus = false, @@ -55,6 +58,7 @@ static const ARMSSEInfo armsse_variants[] = { .sram_banks = 4, .num_cpus = 2, .sys_version = 0x22041743, + .cpuwait_rst = 2, .sys_config_format = SSE200Format, .has_mhus = true, .has_ppus = true, @@ -495,30 +499,33 @@ static void armsse_realize(DeviceState *dev, Error **errp) qdev_prop_set_uint32(cpudev, "num-irq", s->exp_numirq + 32); /* - * In real hardware the initial Secure VTOR is set from the INITSVTOR0 - * register in the IoT Kit System Control Register block, and the - * initial value of that is in turn specifiable by the FPGA that - * instantiates the IoT Kit. In QEMU we don't implement this wrinkle, - * and simply set the CPU's init-svtor to the IoT Kit default value. - * In SSE-200 the situation is similar, except that the default value - * is a reset-time signal input. Typically a board using the SSE-200 - * will have a system control processor whose boot firmware initializes - * the INITSVTOR* registers before powering up the CPUs in any case, - * so the hardware's default value doesn't matter. QEMU doesn't emulate + * In real hardware the initial Secure VTOR is set from the INITSVTOR* + * registers in the IoT Kit System Control Register block. In QEMU + * we set the initial value here, and also the reset value of the + * sysctl register, from this object's QOM init-svtor property. + * If the guest changes the INITSVTOR* registers at runtime then the + * code in iotkit-sysctl.c will update the CPU init-svtor property + * (which will then take effect on the next CPU warm-reset). + * + * Note that typically a board using the SSE-200 will have a system + * control processor whose boot firmware initializes the INITSVTOR* + * registers before powering up the CPUs. QEMU doesn't emulate * the control processor, so instead we behave in the way that the - * firmware does. The initial value is configurable by the board code - * to match whatever its firmware does. + * firmware does: the initial value should be set by the board code + * (using the init-svtor property on the ARMSSE object) to match + * whatever its firmware does. */ qdev_prop_set_uint32(cpudev, "init-svtor", s->init_svtor); /* - * Start all CPUs except CPU0 powered down. In real hardware it is - * a configurable property of the SSE-200 which CPUs start powered up - * (via the CPUWAIT0_RST and CPUWAIT1_RST parameters), but since all - * the boards we care about start CPU0 and leave CPU1 powered off, - * we hard-code that for now. We can add QOM properties for this + * CPUs start powered down if the corresponding bit in the CPUWAIT + * register is 1. In real hardware the CPUWAIT register reset value is + * a configurable property of the SSE-200 (via the CPUWAIT0_RST and + * CPUWAIT1_RST parameters), but since all the boards we care about + * start CPU0 and leave CPU1 powered off, we hard-code that in + * info->cpuwait_rst for now. We can add QOM properties for this * later if necessary. */ - if (i > 0) { + if (extract32(info->cpuwait_rst, i, 1)) { object_property_set_bool(cpuobj, true, "start-powered-off", &err); if (err) { error_propagate(errp, err); @@ -999,6 +1006,12 @@ static void armsse_realize(DeviceState *dev, Error **errp) /* System control registers */ object_property_set_int(OBJECT(&s->sysctl), info->sys_version, "SYS_VERSION", &err); + object_property_set_int(OBJECT(&s->sysctl), info->cpuwait_rst, + "CPUWAIT_RST", &err); + object_property_set_int(OBJECT(&s->sysctl), s->init_svtor, + "INITSVTOR0_RST", &err); + object_property_set_int(OBJECT(&s->sysctl), s->init_svtor, + "INITSVTOR1_RST", &err); object_property_set_bool(OBJECT(&s->sysctl), true, "realized", &err); if (err) { error_propagate(errp, err); |