summaryrefslogtreecommitdiffstats
path: root/hw/mem/Kconfig
Commit message (Collapse)AuthorAgeFilesLines
* hw/cxl/device: Add a memory device (8.2.8.5)Ben Widawsky2022-05-131-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | A CXL memory device (AKA Type 3) is a CXL component that contains some combination of volatile and persistent memory. It also implements the previously defined mailbox interface as well as the memory device firmware interface. Although the memory device is configured like a normal PCIe device, the memory traffic is on an entirely separate bus conceptually (using the same physical wires as PCIe, but different protocol). Once the CXL topology is fully configure and address decoders committed, the guest physical address for the memory device is part of a larger window which is owned by the platform. The creation of these windows is later in this series. The following example will create a 256M device in a 512M window: -object "memory-backend-file,id=cxl-mem1,share,mem-path=cxl-type3,size=512M" -device "cxl-type3,bus=rp0,memdev=cxl-mem1,id=cxl-pmem0" Note: Dropped PCDIMM info interfaces for now. They can be added if appropriate at a later date. Signed-off-by: Ben Widawsky <ben.widawsky@intel.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Message-Id: <20220429144110.25167-18-Jonathan.Cameron@huawei.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* kconfig: split CONFIG_SPARSE_MEM from fuzzingPaolo Bonzini2021-10-141-0/+3
| | | | | | | | | | | | | Pass CONFIG_FUZZ via host_kconfig, and use it to select the sparse-mem device. Cc: Alexander Oleinik <alxndr@bu.edu> Reviewed-by: Alexander Bulekov <alxndr@bu.edu> Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com> Tested-by: Alexander Bulekov <alxndr@bu.edu> Message-Id: <20211007130829.632254-1-pbonzini@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* hw/mem/nvdimm: Use Kconfig 'imply' instead of 'depends on'Philippe Mathieu-Daudé2021-05-261-2/+0Star
| | | | | | | | | | | | | | | Per the kconfig.rst: A device should be listed [...] ``imply`` if (depending on the QEMU command line) the board may or may not be started without it. This is the case with the NVDIMM device, so use the 'imply' weak reverse dependency to select the symbol. Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com> Message-Id: <20210511155354.3069141-2-philmd@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* meson: convert hw/memMarc-André Lureau2020-08-211-0/+1
| | | | | Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* hw/arm/virt: Add nvdimm hot-plug infrastructureKwangwoo Lee2020-05-041-1/+1
| | | | | | | | | | | | | | | This adds support to init nvdimm acpi state and build nvdimm acpi tables. Please note nvdimm_support is not yet enabled. Signed-off-by: Kwangwoo Lee <kwangwoo.lee@sk.com> Signed-off-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com> Reviewed-by: Igor Mammedov <imammedo@redhat.com> Message-Id: <20200421125934.14952-4-shameerali.kolothum.thodi@huawei.com> Acked-by: Peter Maydell <peter.maydell@linaro.org> Tested-by: Eric Auger <eric.auger@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* spapr: Add NVDIMM device supportShivaprasad G Bhat2020-02-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for NVDIMM devices for sPAPR. Piggyback on existing nvdimm device interface in QEMU to support virtual NVDIMM devices for Power. Create the required DT entries for the device (some entries have dummy values right now). The patch creates the required DT node and sends a hotplug interrupt to the guest. Guest is expected to undertake the normal DR resource add path in response and start issuing PAPR SCM hcalls. The device support is verified based on the machine version unlike x86. This is how it can be used .. Ex : For coldplug, the device to be added in qemu command line as shown below -object memory-backend-file,id=memnvdimm0,prealloc=yes,mem-path=/tmp/nvdimm0,share=yes,size=1073872896 -device nvdimm,label-size=128k,uuid=75a3cdd7-6a2f-4791-8d15-fe0a920e8e9e,memdev=memnvdimm0,id=nvdimm0,slot=0 For hotplug, the device to be added from monitor as below object_add memory-backend-file,id=memnvdimm0,prealloc=yes,mem-path=/tmp/nvdimm0,share=yes,size=1073872896 device_add nvdimm,label-size=128k,uuid=75a3cdd7-6a2f-4791-8d15-fe0a920e8e9e,memdev=memnvdimm0,id=nvdimm0,slot=0 Signed-off-by: Shivaprasad G Bhat <sbhat@linux.ibm.com> Signed-off-by: Bharata B Rao <bharata@linux.ibm.com> [Early implementation] Message-Id: <158131058078.2897.12767731856697459923.stgit@lep8c.aus.stglabs.ibm.com> Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
* ppc64: Express dependencies of 'pseries' and 'powernv' machines with kconfigThomas Huth2019-03-071-0/+1
| | | | | | | | | | | | | | The POWERNV switch should always select ISA_IPMI_BT, then the other IPMI options are turned on automatically now. CONFIG_DIMM should always be selected by the pseries machine, which in turn depends on CONFIG_MEM_DEVICE since DIMM implements this interface. CONFIG_VIRTIO_VGA can be dropped from default-configs/ppc64-softmmu.mak completely since this device is already automatically enabled via hw/display/Kconfig now. Signed-off-by: Thomas Huth <thuth@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* i386-softmmu.mak: remove all CONFIG_* except boards definitionsYang Zhong2019-03-071-0/+2
| | | | | | | | %-softmmu.mak only keep boards definitions in Kconfig mode. Signed-off-by: Yang Zhong <yang.zhong@intel.com> Message-Id: <20190123065618.3520-43-yang.zhong@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* kconfig: introduce kconfig filesPaolo Bonzini2019-03-071-0/+8
The Kconfig files were generated mostly with this script: for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' ` shift if test $# = 1; then cat >> $(dirname $1)/Kconfig << EOF config ${i#CONFIG_} bool EOF git add $(dirname $1)/Kconfig else echo $i $* fi done sed -i '$d' hw/*/Kconfig for i in hw/*; do if test -d $i && ! test -f $i/Kconfig; then touch $i/Kconfig git add $i/Kconfig fi done Whenever a symbol is referenced from multiple subdirectories, the script prints the list of directories that reference the symbol. These symbols have to be added manually to the Kconfig files. Kconfig.host and hw/Kconfig were created manually. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Yang Zhong <yang.zhong@intel.com> Message-Id: <20190123065618.3520-27-yang.zhong@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>