Initial revision

1 files changed, 3713 insertions, 0 deletions

diff --git a/src/drivers/net/e1000.c b/src/drivers/net/e1000.c
new file mode 100644
index 00000000..7c572656
--- /dev/null
+++ b/src/drivers/net/e1000.c
@@ -0,0 +1,3713 @@
+/**************************************************************************
+Etherboot -  BOOTP/TFTP Bootstrap Program
+Inter Pro 1000 for Etherboot
+Drivers are port from Intel's Linux driver e1000-4.3.15
+
+***************************************************************************/
+/*******************************************************************************
+
+  
+  Copyright(c) 1999 - 2003 Intel Corporation. All rights reserved.
+  
+  This program is free software; you can redistribute it and/or modify it 
+  under the terms of the GNU General Public License as published by the Free 
+  Software Foundation; either version 2 of the License, or (at your option) 
+  any later version.
+  
+  This program is distributed in the hope that it will be useful, but WITHOUT 
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or 
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for 
+  more details.
+  
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc., 59 
+  Temple Place - Suite 330, Boston, MA  02111-1307, USA.
+  
+  The full GNU General Public License is included in this distribution in the
+  file called LICENSE.
+  
+  Contact Information:
+  Linux NICS <linux.nics@intel.com>
+  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+/*
+ *  Copyright (C) Archway Digital Solutions.
+ *
+ *  written by Chrsitopher Li <cli at arcyway dot com> or <chrisl at gnuchina dot org>
+ *  2/9/2002
+ *
+ *  Copyright (C) Linux Networx.
+ *  Massive upgrade to work with the new intel gigabit NICs.
+ *  <ebiederman at lnxi dot com>
+ *
+ *  Support for 82541ei & 82547ei chips from Intel's Linux driver 5.1.13 added by
+ *  Georg Baum <gbaum@users.sf.net>, sponsored by PetaMem GmbH and linkLINE Communications, Inc.
+ *
+ *  01/2004: Updated to Linux driver 5.2.22 by Georg Baum <gbaum@users.sf.net>
+ */
+
+/* to get some global routines like printf */
+#include "etherboot.h"
+/* to get the interface to the body of the program */
+#include "nic.h"
+/* to get the PCI support functions, if this is a PCI NIC */
+#include "pci.h"
+#include "timer.h"
+
+typedef unsigned char *dma_addr_t;
+
+typedef enum {
+	FALSE = 0,
+	TRUE = 1
+} boolean_t;
+
+#define DEBUG 0
+
+
+/* Some pieces of code are disabled with #if 0 ... #endif.
+ * They are not deleted to show where the etherboot driver differs
+ * from the linux driver below the function level.
+ * Some member variables of the hw struct have been eliminated
+ * and the corresponding inplace checks inserted instead.
+ * Pieces such as LED handling that we definitely don't need are deleted.
+ *
+ * The following defines should not be needed normally,
+ * but may be helpful for debugging purposes. */
+
+/* Define this if you want to program the transmission control register
+ * the way the Linux driver does it. */
+#undef LINUX_DRIVER_TCTL
+
+/* Define this to behave more like the Linux driver. */
+#undef LINUX_DRIVER
+
+#include "e1000_hw.h"
+
+/* NIC specific static variables go here */
+static struct e1000_hw hw;
+static char tx_pool[128 + 16];
+static char rx_pool[128 + 16];
+static char packet[2096];
+
+static struct e1000_tx_desc *tx_base;
+static struct e1000_rx_desc *rx_base;
+
+static int tx_tail;
+static int rx_tail, rx_last;
+
+/* Function forward declarations */
+static int e1000_setup_link(struct e1000_hw *hw);
+static int e1000_setup_fiber_serdes_link(struct e1000_hw *hw);
+static int e1000_setup_copper_link(struct e1000_hw *hw);
+static int e1000_phy_setup_autoneg(struct e1000_hw *hw);
+static void e1000_config_collision_dist(struct e1000_hw *hw);
+static int e1000_config_mac_to_phy(struct e1000_hw *hw);
+static int e1000_config_fc_after_link_up(struct e1000_hw *hw);
+static int e1000_check_for_link(struct e1000_hw *hw);
+static int e1000_wait_autoneg(struct e1000_hw *hw);
+static void e1000_get_speed_and_duplex(struct e1000_hw *hw, uint16_t *speed, uint16_t *duplex);
+static int e1000_read_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *phy_data);
+static int e1000_read_phy_reg_ex(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *phy_data);
+static int e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t phy_data);
+static int e1000_write_phy_reg_ex(struct e1000_hw *hw, uint32_t reg_addr, uint16_t phy_data);
+static void e1000_phy_hw_reset(struct e1000_hw *hw);
+static int e1000_phy_reset(struct e1000_hw *hw);
+static int e1000_detect_gig_phy(struct e1000_hw *hw);
+static void e1000_irq(struct nic *nic, irq_action_t action);
+
+/* Printing macros... */
+
+#define E1000_ERR(args...) printf("e1000: " args)
+
+#if DEBUG >= 3
+#define E1000_DBG(args...) printf("e1000: " args)
+#else
+#define E1000_DBG(args...)
+#endif
+
+#define MSGOUT(S, A, B)     printk(S "\n", A, B)
+#if DEBUG >= 2
+#define DEBUGFUNC(F)        DEBUGOUT(F "\n");
+#else
+#define DEBUGFUNC(F)
+#endif
+#if DEBUG >= 1
+#define DEBUGOUT(S) printf(S)
+#define DEBUGOUT1(S,A) printf(S,A)
+#define DEBUGOUT2(S,A,B) printf(S,A,B)
+#define DEBUGOUT3(S,A,B,C) printf(S,A,B,C)
+#define DEBUGOUT7(S,A,B,C,D,E,F,G) printf(S,A,B,C,D,E,F,G)
+#else
+#define DEBUGOUT(S)
+#define DEBUGOUT1(S,A)
+#define DEBUGOUT2(S,A,B)
+#define DEBUGOUT3(S,A,B,C)
+#define DEBUGOUT7(S,A,B,C,D,E,F,G)
+#endif
+
+#define E1000_WRITE_REG(a, reg, value) ( \
+    ((a)->mac_type >= e1000_82543) ? \
+        (writel((value), ((a)->hw_addr + E1000_##reg))) : \
+        (writel((value), ((a)->hw_addr + E1000_82542_##reg))))
+
+#define E1000_READ_REG(a, reg) ( \
+    ((a)->mac_type >= e1000_82543) ? \
+        readl((a)->hw_addr + E1000_##reg) : \
+        readl((a)->hw_addr + E1000_82542_##reg))
+
+#define E1000_WRITE_REG_ARRAY(a, reg, offset, value) ( \
+    ((a)->mac_type >= e1000_82543) ? \
+        writel((value), ((a)->hw_addr + E1000_##reg + ((offset) << 2))) : \
+        writel((value), ((a)->hw_addr + E1000_82542_##reg + ((offset) << 2))))
+
+#define E1000_READ_REG_ARRAY(a, reg, offset) ( \
+    ((a)->mac_type >= e1000_82543) ? \
+        readl((a)->hw_addr + E1000_##reg + ((offset) << 2)) : \
+        readl((a)->hw_addr + E1000_82542_##reg + ((offset) << 2)))
+
+#define E1000_WRITE_FLUSH(a) {uint32_t x; x = E1000_READ_REG(a, STATUS);}
+
+uint32_t
+e1000_io_read(struct e1000_hw *hw __unused, uint32_t port)
+{
+        return inl(port);
+}
+
+void
+e1000_io_write(struct e1000_hw *hw __unused, uint32_t port, uint32_t value)
+{
+        outl(value, port);
+}
+
+static inline void e1000_pci_set_mwi(struct e1000_hw *hw)
+{
+	pci_write_config_word(hw->pdev, PCI_COMMAND, hw->pci_cmd_word);
+}
+
+static inline void e1000_pci_clear_mwi(struct e1000_hw *hw)
+{
+	pci_write_config_word(hw->pdev, PCI_COMMAND,
+			      hw->pci_cmd_word & ~PCI_COMMAND_INVALIDATE);
+}
+
+/******************************************************************************
+ * Raises the EEPROM's clock input.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * eecd - EECD's current value
+ *****************************************************************************/
+static void
+e1000_raise_ee_clk(struct e1000_hw *hw,
+                   uint32_t *eecd)
+{
+	/* Raise the clock input to the EEPROM (by setting the SK bit), and then
+	 * wait <delay> microseconds.
+	 */
+	*eecd = *eecd | E1000_EECD_SK;
+	E1000_WRITE_REG(hw, EECD, *eecd);
+	E1000_WRITE_FLUSH(hw);
+	udelay(hw->eeprom.delay_usec);
+}
+
+/******************************************************************************
+ * Lowers the EEPROM's clock input.
+ *
+ * hw - Struct containing variables accessed by shared code 
+ * eecd - EECD's current value
+ *****************************************************************************/
+static void
+e1000_lower_ee_clk(struct e1000_hw *hw,
+                   uint32_t *eecd)
+{
+	/* Lower the clock input to the EEPROM (by clearing the SK bit), and then 
+	 * wait 50 microseconds. 
+	 */
+	*eecd = *eecd & ~E1000_EECD_SK;
+	E1000_WRITE_REG(hw, EECD, *eecd);
+	E1000_WRITE_FLUSH(hw);
+	udelay(hw->eeprom.delay_usec);
+}
+
+/******************************************************************************
+ * Shift data bits out to the EEPROM.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * data - data to send to the EEPROM
+ * count - number of bits to shift out
+ *****************************************************************************/
+static void
+e1000_shift_out_ee_bits(struct e1000_hw *hw,
+                        uint16_t data,
+                        uint16_t count)
+{
+	struct e1000_eeprom_info *eeprom = &hw->eeprom;
+	uint32_t eecd;
+	uint32_t mask;
+	
+	/* We need to shift "count" bits out to the EEPROM. So, value in the
+	 * "data" parameter will be shifted out to the EEPROM one bit at a time.
+	 * In order to do this, "data" must be broken down into bits. 
+	 */
+	mask = 0x01 << (count - 1);
+	eecd = E1000_READ_REG(hw, EECD);
+	if (eeprom->type == e1000_eeprom_microwire) {
+		eecd &= ~E1000_EECD_DO;
+	} else if (eeprom->type == e1000_eeprom_spi) {
+		eecd |= E1000_EECD_DO;
+	}
+	do {
+		/* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1",
+		 * and then raising and then lowering the clock (the SK bit controls
+		 * the clock input to the EEPROM).  A "0" is shifted out to the EEPROM
+		 * by setting "DI" to "0" and then raising and then lowering the clock.
+		 */
+		eecd &= ~E1000_EECD_DI;
+		
+		if(data & mask)
+			eecd |= E1000_EECD_DI;
+		
+		E1000_WRITE_REG(hw, EECD, eecd);
+		E1000_WRITE_FLUSH(hw);
+		
+		udelay(eeprom->delay_usec);
+		
+		e1000_raise_ee_clk(hw, &eecd);
+		e1000_lower_ee_clk(hw, &eecd);
+		
+		mask = mask >> 1;
+		
+	} while(mask);
+
+	/* We leave the "DI" bit set to "0" when we leave this routine. */
+	eecd &= ~E1000_EECD_DI;
+	E1000_WRITE_REG(hw, EECD, eecd);
+}
+
+/******************************************************************************
+ * Shift data bits in from the EEPROM
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+static uint16_t
+e1000_shift_in_ee_bits(struct e1000_hw *hw,
+                       uint16_t count)
+{
+	uint32_t eecd;
+	uint32_t i;
+	uint16_t data;
+	
+	/* In order to read a register from the EEPROM, we need to shift 'count' 
+	 * bits in from the EEPROM. Bits are "shifted in" by raising the clock
+	 * input to the EEPROM (setting the SK bit), and then reading the value of
+	 * the "DO" bit.  During this "shifting in" process the "DI" bit should
+	 * always be clear.
+	 */
+	
+	eecd = E1000_READ_REG(hw, EECD);
+	
+	eecd &= ~(E1000_EECD_DO | E1000_EECD_DI);
+	data = 0;
+	
+	for(i = 0; i < count; i++) {
+		data = data << 1;
+		e1000_raise_ee_clk(hw, &eecd);
+		
+		eecd = E1000_READ_REG(hw, EECD);
+		
+		eecd &= ~(E1000_EECD_DI);
+		if(eecd & E1000_EECD_DO)
+			data |= 1;
+		
+		e1000_lower_ee_clk(hw, &eecd);
+	}
+	
+	return data;
+}
+
+/******************************************************************************
+ * Prepares EEPROM for access
+ *
+ * hw - Struct containing variables accessed by shared code
+ *
+ * Lowers EEPROM clock. Clears input pin. Sets the chip select pin. This 
+ * function should be called before issuing a command to the EEPROM.
+ *****************************************************************************/
+static int32_t
+e1000_acquire_eeprom(struct e1000_hw *hw)
+{
+	struct e1000_eeprom_info *eeprom = &hw->eeprom;
+	uint32_t eecd, i=0;
+
+	eecd = E1000_READ_REG(hw, EECD);
+
+	/* Request EEPROM Access */
+	if(hw->mac_type > e1000_82544) {
+		eecd |= E1000_EECD_REQ;
+		E1000_WRITE_REG(hw, EECD, eecd);
+		eecd = E1000_READ_REG(hw, EECD);
+		while((!(eecd & E1000_EECD_GNT)) &&
+		      (i < E1000_EEPROM_GRANT_ATTEMPTS)) {
+			i++;
+			udelay(5);
+			eecd = E1000_READ_REG(hw, EECD);
+		}
+		if(!(eecd & E1000_EECD_GNT)) {
+			eecd &= ~E1000_EECD_REQ;
+			E1000_WRITE_REG(hw, EECD, eecd);
+			DEBUGOUT("Could not acquire EEPROM grant\n");
+			return -E1000_ERR_EEPROM;
+		}
+	}
+
+	/* Setup EEPROM for Read/Write */
+
+	if (eeprom->type == e1000_eeprom_microwire) {
+		/* Clear SK and DI */
+		eecd &= ~(E1000_EECD_DI | E1000_EECD_SK);
+		E1000_WRITE_REG(hw, EECD, eecd);
+
+		/* Set CS */
+		eecd |= E1000_EECD_CS;
+		E1000_WRITE_REG(hw, EECD, eecd);
+	} else if (eeprom->type == e1000_eeprom_spi) {
+		/* Clear SK and CS */
+		eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
+		E1000_WRITE_REG(hw, EECD, eecd);
+		udelay(1);
+	}
+
+	return E1000_SUCCESS;
+}
+
+/******************************************************************************
+ * Returns EEPROM to a "standby" state
+ * 
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+static void
+e1000_standby_eeprom(struct e1000_hw *hw)
+{
+	struct e1000_eeprom_info *eeprom = &hw->eeprom;
+	uint32_t eecd;
+	
+	eecd = E1000_READ_REG(hw, EECD);
+
+	if(eeprom->type == e1000_eeprom_microwire) {
+
+		/* Deselect EEPROM */
+		eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
+		E1000_WRITE_REG(hw, EECD, eecd);
+		E1000_WRITE_FLUSH(hw);
+		udelay(eeprom->delay_usec);
+	
+		/* Clock high */
+		eecd |= E1000_EECD_SK;
+		E1000_WRITE_REG(hw, EECD, eecd);
+		E1000_WRITE_FLUSH(hw);
+		udelay(eeprom->delay_usec);
+	
+		/* Select EEPROM */
+		eecd |= E1000_EECD_CS;
+		E1000_WRITE_REG(hw, EECD, eecd);
+		E1000_WRITE_FLUSH(hw);
+		udelay(eeprom->delay_usec);
+
+		/* Clock low */
+		eecd &= ~E1000_EECD_SK;
+		E1000_WRITE_REG(hw, EECD, eecd);
+		E1000_WRITE_FLUSH(hw);
+		udelay(eeprom->delay_usec);
+	} else if(eeprom->type == e1000_eeprom_spi) {
+		/* Toggle CS to flush commands */
+		eecd |= E1000_EECD_CS;
+		E1000_WRITE_REG(hw, EECD, eecd);
+		E1000_WRITE_FLUSH(hw);
+		udelay(eeprom->delay_usec);
+		eecd &= ~E1000_EECD_CS;
+		E1000_WRITE_REG(hw, EECD, eecd);
+		E1000_WRITE_FLUSH(hw);
+		udelay(eeprom->delay_usec);
+	}
+}
+
+/******************************************************************************
+ * Terminates a command by inverting the EEPROM's chip select pin
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+static void
+e1000_release_eeprom(struct e1000_hw *hw)
+{
+	uint32_t eecd;
+
+	eecd = E1000_READ_REG(hw, EECD);
+
+	if (hw->eeprom.type == e1000_eeprom_spi) {
+		eecd |= E1000_EECD_CS;  /* Pull CS high */
+		eecd &= ~E1000_EECD_SK; /* Lower SCK */
+
+		E1000_WRITE_REG(hw, EECD, eecd);
+
+		udelay(hw->eeprom.delay_usec);
+	} else if(hw->eeprom.type == e1000_eeprom_microwire) {
+		/* cleanup eeprom */
+
+		/* CS on Microwire is active-high */
+		eecd &= ~(E1000_EECD_CS | E1000_EECD_DI);
+
+		E1000_WRITE_REG(hw, EECD, eecd);
+
+		/* Rising edge of clock */
+		eecd |= E1000_EECD_SK;
+		E1000_WRITE_REG(hw, EECD, eecd);
+		E1000_WRITE_FLUSH(hw);
+		udelay(hw->eeprom.delay_usec);
+
+		/* Falling edge of clock */
+		eecd &= ~E1000_EECD_SK;
+		E1000_WRITE_REG(hw, EECD, eecd);
+		E1000_WRITE_FLUSH(hw);
+		udelay(hw->eeprom.delay_usec);
+	}
+
+	/* Stop requesting EEPROM access */
+	if(hw->mac_type > e1000_82544) {
+		eecd &= ~E1000_EECD_REQ;
+		E1000_WRITE_REG(hw, EECD, eecd);
+	}
+}
+
+/******************************************************************************
+ * Reads a 16 bit word from the EEPROM.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+static int32_t
+e1000_spi_eeprom_ready(struct e1000_hw *hw)
+{
+	uint16_t retry_count = 0;
+	uint8_t spi_stat_reg;
+
+	/* Read "Status Register" repeatedly until the LSB is cleared.  The
+	 * EEPROM will signal that the command has been completed by clearing
+	 * bit 0 of the internal status register.  If it's not cleared within
+	 * 5 milliseconds, then error out.
+	 */
+	retry_count = 0;
+	do {
+		e1000_shift_out_ee_bits(hw, EEPROM_RDSR_OPCODE_SPI,
+		hw->eeprom.opcode_bits);
+		spi_stat_reg = (uint8_t)e1000_shift_in_ee_bits(hw, 8);
+		if (!(spi_stat_reg & EEPROM_STATUS_RDY_SPI))
+			break;
+
+		udelay(5);
+		retry_count += 5;
+
+	} while(retry_count < EEPROM_MAX_RETRY_SPI);
+
+	/* ATMEL SPI write time could vary from 0-20mSec on 3.3V devices (and
+	 * only 0-5mSec on 5V devices)
+	 */
+	if(retry_count >= EEPROM_MAX_RETRY_SPI) {
+		DEBUGOUT("SPI EEPROM Status error\n");
+		return -E1000_ERR_EEPROM;
+	}
+
+	return E1000_SUCCESS;
+}
+
+/******************************************************************************
+ * Reads a 16 bit word from the EEPROM.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * offset - offset of  word in the EEPROM to read
+ * data - word read from the EEPROM
+ * words - number of words to read
+ *****************************************************************************/
+static int
+e1000_read_eeprom(struct e1000_hw *hw,
+                  uint16_t offset,
+		  uint16_t words,
+                  uint16_t *data)
+{
+	struct e1000_eeprom_info *eeprom = &hw->eeprom;
+	uint32_t i = 0;
+	
+	DEBUGFUNC("e1000_read_eeprom");
+
+	/* A check for invalid values:  offset too large, too many words, and not
+	 * enough words.
+	 */
+	if((offset > eeprom->word_size) || (words > eeprom->word_size - offset) ||
+	   (words == 0)) {
+		DEBUGOUT("\"words\" parameter out of bounds\n");
+		return -E1000_ERR_EEPROM;
+	}
+
+	/*  Prepare the EEPROM for reading  */
+	if(e1000_acquire_eeprom(hw) != E1000_SUCCESS)
+		return -E1000_ERR_EEPROM;
+
+	if(eeprom->type == e1000_eeprom_spi) {
+		uint16_t word_in;
+		uint8_t read_opcode = EEPROM_READ_OPCODE_SPI;
+
+		if(e1000_spi_eeprom_ready(hw)) {
+			e1000_release_eeprom(hw);
+			return -E1000_ERR_EEPROM;
+		}
+
+		e1000_standby_eeprom(hw);
+
+		/* Some SPI eeproms use the 8th address bit embedded in the opcode */
+		if((eeprom->address_bits == 8) && (offset >= 128))
+			read_opcode |= EEPROM_A8_OPCODE_SPI;
+
+		/* Send the READ command (opcode + addr)  */
+		e1000_shift_out_ee_bits(hw, read_opcode, eeprom->opcode_bits);
+		e1000_shift_out_ee_bits(hw, (uint16_t)(offset*2), eeprom->address_bits);
+
+		/* Read the data.  The address of the eeprom internally increments with
+		 * each byte (spi) being read, saving on the overhead of eeprom setup
+		 * and tear-down.  The address counter will roll over if reading beyond
+		 * the size of the eeprom, thus allowing the entire memory to be read
+		 * starting from any offset. */
+		for (i = 0; i < words; i++) {
+			word_in = e1000_shift_in_ee_bits(hw, 16);
+			data[i] = (word_in >> 8) | (word_in << 8);
+		}
+	} else if(eeprom->type == e1000_eeprom_microwire) {
+		for (i = 0; i < words; i++) {
+			/*  Send the READ command (opcode + addr)  */
+			e1000_shift_out_ee_bits(hw, EEPROM_READ_OPCODE_MICROWIRE,
+						eeprom->opcode_bits);
+			e1000_shift_out_ee_bits(hw, (uint16_t)(offset + i),
+			                        eeprom->address_bits);
+
+			/* Read the data.  For microwire, each word requires the overhead
+			 * of eeprom setup and tear-down. */
+			data[i] = e1000_shift_in_ee_bits(hw, 16);
+			e1000_standby_eeprom(hw);
+		}
+	}
+
+	/* End this read operation */
+	e1000_release_eeprom(hw);
+
+	return E1000_SUCCESS;
+}
+
+/******************************************************************************
+ * Verifies that the EEPROM has a valid checksum
+ * 
+ * hw - Struct containing variables accessed by shared code
+ *
+ * Reads the first 64 16 bit words of the EEPROM and sums the values read.
+ * If the the sum of the 64 16 bit words is 0xBABA, the EEPROM's checksum is
+ * valid.
+ *****************************************************************************/
+static int
+e1000_validate_eeprom_checksum(struct e1000_hw *hw)
+{
+	uint16_t checksum = 0;
+	uint16_t i, eeprom_data;
+
+	DEBUGFUNC("e1000_validate_eeprom_checksum");
+
+	for(i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) {
+		if(e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
+			DEBUGOUT("EEPROM Read Error\n");
+			return -E1000_ERR_EEPROM;
+		}
+		checksum += eeprom_data;
+	}
+	
+	if(checksum == (uint16_t) EEPROM_SUM)
+		return E1000_SUCCESS;
+	else {
+		DEBUGOUT("EEPROM Checksum Invalid\n");    
+		return -E1000_ERR_EEPROM;
+	}
+}
+
+/******************************************************************************
+ * Reads the adapter's MAC address from the EEPROM and inverts the LSB for the
+ * second function of dual function devices
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+static int 
+e1000_read_mac_addr(struct e1000_hw *hw)
+{
+	uint16_t offset;
+	uint16_t eeprom_data;
+	int i;
+
+	DEBUGFUNC("e1000_read_mac_addr");
+
+	for(i = 0; i < NODE_ADDRESS_SIZE; i += 2) {
+		offset = i >> 1;
+		if(e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) {
+			DEBUGOUT("EEPROM Read Error\n");
+			return -E1000_ERR_EEPROM;
+		}
+		hw->mac_addr[i] = eeprom_data & 0xff;
+		hw->mac_addr[i+1] = (eeprom_data >> 8) & 0xff;
+	}
+	if(((hw->mac_type == e1000_82546) || (hw->mac_type == e1000_82546_rev_3)) &&
+		(E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1))
+		/* Invert the last bit if this is the second device */
+		hw->mac_addr[5] ^= 1;
+	return E1000_SUCCESS;
+}
+
+/******************************************************************************
+ * Initializes receive address filters.
+ *
+ * hw - Struct containing variables accessed by shared code 
+ *
+ * Places the MAC address in receive address register 0 and clears the rest
+ * of the receive addresss registers. Clears the multicast table. Assumes
+ * the receiver is in reset when the routine is called.
+ *****************************************************************************/
+static void
+e1000_init_rx_addrs(struct e1000_hw *hw)
+{
+	uint32_t i;
+	uint32_t addr_low;
+	uint32_t addr_high;
+	
+	DEBUGFUNC("e1000_init_rx_addrs");
+	
+	/* Setup the receive address. */
+	DEBUGOUT("Programming MAC Address into RAR[0]\n");
+	addr_low = (hw->mac_addr[0] |
+		(hw->mac_addr[1] << 8) |
+		(hw->mac_addr[2] << 16) | (hw->mac_addr[3] << 24));
+	
+	addr_high = (hw->mac_addr[4] |
+		(hw->mac_addr[5] << 8) | E1000_RAH_AV);
+	
+	E1000_WRITE_REG_ARRAY(hw, RA, 0, addr_low);
+	E1000_WRITE_REG_ARRAY(hw, RA, 1, addr_high);
+	
+	/* Zero out the other 15 receive addresses. */
+	DEBUGOUT("Clearing RAR[1-15]\n");
+	for(i = 1; i < E1000_RAR_ENTRIES; i++) {
+		E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
+		E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
+	}
+}
+
+/******************************************************************************
+ * Clears the VLAN filer table
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+static void
+e1000_clear_vfta(struct e1000_hw *hw)
+{
+	uint32_t offset;
+    
+	for(offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++)
+		E1000_WRITE_REG_ARRAY(hw, VFTA, offset, 0);
+}
+
+/******************************************************************************
+* Writes a value to one of the devices registers using port I/O (as opposed to
+* memory mapped I/O). Only 82544 and newer devices support port I/O. *
+* hw - Struct containing variables accessed by shared code
+* offset - offset to write to * value - value to write
+*****************************************************************************/
+void e1000_write_reg_io(struct e1000_hw *hw, uint32_t offset, uint32_t value){
+	uint32_t io_addr = hw->io_base;
+	uint32_t io_data = hw->io_base + 4;
+	e1000_io_write(hw, io_addr, offset);
+	e1000_io_write(hw, io_data, value);
+}
+
+/******************************************************************************
+ * Set the phy type member in the hw struct.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+static int32_t
+e1000_set_phy_type(struct e1000_hw *hw)
+{
+	DEBUGFUNC("e1000_set_phy_type");
+
+	switch(hw->phy_id) {
+	case M88E1000_E_PHY_ID:
+	case M88E1000_I_PHY_ID:
+	case M88E1011_I_PHY_ID:
+		hw->phy_type = e1000_phy_m88;
+		break;
+	case IGP01E1000_I_PHY_ID:
+		hw->phy_type = e1000_phy_igp;
+		break;
+	default:
+		/* Should never have loaded on this device */
+		hw->phy_type = e1000_phy_undefined;
+		return -E1000_ERR_PHY_TYPE;
+	}
+
+	return E1000_SUCCESS;
+}
+
+/******************************************************************************
+ * IGP phy init script - initializes the GbE PHY
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+static void
+e1000_phy_init_script(struct e1000_hw *hw)
+{
+	DEBUGFUNC("e1000_phy_init_script");
+
+#if 0
+	/* See e1000_sw_init() of the Linux driver */
+	if(hw->phy_init_script) {
+#else
+	if((hw->mac_type == e1000_82541) ||
+	   (hw->mac_type == e1000_82547) ||
+	   (hw->mac_type == e1000_82541_rev_2) ||
+	   (hw->mac_type == e1000_82547_rev_2)) {
+#endif
+		mdelay(20);
+
+		e1000_write_phy_reg(hw,0x0000,0x0140);
+
+		mdelay(5);
+
+		if(hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547) {
+			e1000_write_phy_reg(hw, 0x1F95, 0x0001);
+
+			e1000_write_phy_reg(hw, 0x1F71, 0xBD21);
+
+			e1000_write_phy_reg(hw, 0x1F79, 0x0018);
+
+			e1000_write_phy_reg(hw, 0x1F30, 0x1600);
+
+			e1000_write_phy_reg(hw, 0x1F31, 0x0014);
+
+			e1000_write_phy_reg(hw, 0x1F32, 0x161C);
+
+			e1000_write_phy_reg(hw, 0x1F94, 0x0003);
+
+			e1000_write_phy_reg(hw, 0x1F96, 0x003F);
+
+			e1000_write_phy_reg(hw, 0x2010, 0x0008);
+		} else {
+			e1000_write_phy_reg(hw, 0x1F73, 0x0099);
+		}
+
+		e1000_write_phy_reg(hw, 0x0000, 0x3300);
+
+
+		if(hw->mac_type == e1000_82547) {
+			uint16_t fused, fine, coarse;
+
+			/* Move to analog registers page */
+			e1000_read_phy_reg(hw, IGP01E1000_ANALOG_SPARE_FUSE_STATUS, &fused);
+
+			if(!(fused & IGP01E1000_ANALOG_SPARE_FUSE_ENABLED)) {
+				e1000_read_phy_reg(hw, IGP01E1000_ANALOG_FUSE_STATUS, &fused);
+
+				fine = fused & IGP01E1000_ANALOG_FUSE_FINE_MASK;
+				coarse = fused & IGP01E1000_ANALOG_FUSE_COARSE_MASK;
+
+				if(coarse > IGP01E1000_ANALOG_FUSE_COARSE_THRESH) {
+					coarse -= IGP01E1000_ANALOG_FUSE_COARSE_10;
+					fine -= IGP01E1000_ANALOG_FUSE_FINE_1;
+				} else if(coarse == IGP01E1000_ANALOG_FUSE_COARSE_THRESH)
+					fine -= IGP01E1000_ANALOG_FUSE_FINE_10;
+
+				fused = (fused & IGP01E1000_ANALOG_FUSE_POLY_MASK) |
+					(fine & IGP01E1000_ANALOG_FUSE_FINE_MASK) |
+					(coarse & IGP01E1000_ANALOG_FUSE_COARSE_MASK);
+
+				e1000_write_phy_reg(hw, IGP01E1000_ANALOG_FUSE_CONTROL, fused);
+				e1000_write_phy_reg(hw, IGP01E1000_ANALOG_FUSE_BYPASS,
+						IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL);
+			}
+		}
+	}
+}
+
+/******************************************************************************
+ * Set the mac type member in the hw struct.
+ * 
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+static int
+e1000_set_mac_type(struct e1000_hw *hw)
+{
+	DEBUGFUNC("e1000_set_mac_type");
+
+	switch (hw->device_id) {
+	case E1000_DEV_ID_82542:
+		switch (hw->revision_id) {
+		case E1000_82542_2_0_REV_ID:
+			hw->mac_type = e1000_82542_rev2_0;
+			break;
+		case E1000_82542_2_1_REV_ID:
+			hw->mac_type = e1000_82542_rev2_1;
+			break;
+		default:
+			/* Invalid 82542 revision ID */
+			return -E1000_ERR_MAC_TYPE;
+		}
+		break;
+	case E1000_DEV_ID_82543GC_FIBER:
+	case E1000_DEV_ID_82543GC_COPPER:
+		hw->mac_type = e1000_82543;
+		break;
+	case E1000_DEV_ID_82544EI_COPPER:
+	case E1000_DEV_ID_82544EI_FIBER:
+	case E1000_DEV_ID_82544GC_COPPER:
+	case E1000_DEV_ID_82544GC_LOM:
+		hw->mac_type = e1000_82544;
+		break;
+	case E1000_DEV_ID_82540EM:
+	case E1000_DEV_ID_82540EM_LOM:
+	case E1000_DEV_ID_82540EP:
+	case E1000_DEV_ID_82540EP_LOM:
+	case E1000_DEV_ID_82540EP_LP:
+		hw->mac_type = e1000_82540;
+		break;
+	case E1000_DEV_ID_82545EM_COPPER:
+	case E1000_DEV_ID_82545EM_FIBER:
+		hw->mac_type = e1000_82545;
+		break;
+	case E1000_DEV_ID_82545GM_COPPER:
+	case E1000_DEV_ID_82545GM_FIBER:
+	case E1000_DEV_ID_82545GM_SERDES:
+		hw->mac_type = e1000_82545_rev_3;
+		break;
+	case E1000_DEV_ID_82546EB_COPPER:
+	case E1000_DEV_ID_82546EB_FIBER:
+	case E1000_DEV_ID_82546EB_QUAD_COPPER:
+		hw->mac_type = e1000_82546;
+		break;
+	case E1000_DEV_ID_82546GB_COPPER:
+	case E1000_DEV_ID_82546GB_FIBER:
+	case E1000_DEV_ID_82546GB_SERDES:
+		hw->mac_type = e1000_82546_rev_3;
+		break;
+	case E1000_DEV_ID_82541EI:
+	case E1000_DEV_ID_82541EI_MOBILE:
+		hw->mac_type = e1000_82541;
+		break;
+	case E1000_DEV_ID_82541ER:
+	case E1000_DEV_ID_82541GI:
+	case E1000_DEV_ID_82541GI_MOBILE:
+		hw->mac_type = e1000_82541_rev_2;
+		break;
+	case E1000_DEV_ID_82547EI:
+		hw->mac_type = e1000_82547;
+		break;
+	case E1000_DEV_ID_82547GI:
+		hw->mac_type = e1000_82547_rev_2;
+		break;
+	default:
+		/* Should never have loaded on this device */
+		return -E1000_ERR_MAC_TYPE;
+	}
+
+	return E1000_SUCCESS;
+}
+
+/*****************************************************************************
+ * Set media type and TBI compatibility.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * **************************************************************************/
+static void
+e1000_set_media_type(struct e1000_hw *hw)
+{
+	uint32_t status;
+
+	DEBUGFUNC("e1000_set_media_type");
+	
+	if(hw->mac_type != e1000_82543) {
+		/* tbi_compatibility is only valid on 82543 */
+		hw->tbi_compatibility_en = FALSE;
+	}
+
+	switch (hw->device_id) {
+		case E1000_DEV_ID_82545GM_SERDES:
+		case E1000_DEV_ID_82546GB_SERDES:
+			hw->media_type = e1000_media_type_internal_serdes;
+			break;
+		default:
+			if(hw->mac_type >= e1000_82543) {
+				status = E1000_READ_REG(hw, STATUS);
+				if(status & E1000_STATUS_TBIMODE) {
+					hw->media_type = e1000_media_type_fiber;
+					/* tbi_compatibility not valid on fiber */
+					hw->tbi_compatibility_en = FALSE;
+				} else {
+					hw->media_type = e1000_media_type_copper;
+				}
+			} else {
+				/* This is an 82542 (fiber only) */
+				hw->media_type = e1000_media_type_fiber;
+			}
+	}
+}
+
+/******************************************************************************
+ * Reset the transmit and receive units; mask and clear all interrupts.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+static void
+e1000_reset_hw(struct e1000_hw *hw)
+{
+	uint32_t ctrl;
+	uint32_t ctrl_ext;
+	uint32_t icr;
+	uint32_t manc;
+	
+	DEBUGFUNC("e1000_reset_hw");
+	
+	/* For 82542 (rev 2.0), disable MWI before issuing a device reset */
+	if(hw->mac_type == e1000_82542_rev2_0) {
+		DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
+		e1000_pci_clear_mwi(hw);
+	}
+
+	/* Clear interrupt mask to stop board from generating interrupts */
+	DEBUGOUT("Masking off all interrupts\n");
+	E1000_WRITE_REG(hw, IMC, 0xffffffff);
+	
+	/* Disable the Transmit and Receive units.  Then delay to allow
+	 * any pending transactions to complete before we hit the MAC with
+	 * the global reset.
+	 */
+	E1000_WRITE_REG(hw, RCTL, 0);
+	E1000_WRITE_REG(hw, TCTL, E1000_TCTL_PSP);
+	E1000_WRITE_FLUSH(hw);
+
+	/* The tbi_compatibility_on Flag must be cleared when Rctl is cleared. */
+	hw->tbi_compatibility_on = FALSE;
+
+	/* Delay to allow any outstanding PCI transactions to complete before
+	 * resetting the device
+	 */ 
+	mdelay(10);
+
+	ctrl = E1000_READ_REG(hw, CTRL);
+
+	/* Must reset the PHY before resetting the MAC */
+	if((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+		E1000_WRITE_REG_IO(hw, CTRL, (ctrl | E1000_CTRL_PHY_RST));
+		mdelay(5);
+	}
+
+	/* Issue a global reset to the MAC.  This will reset the chip's
+	 * transmit, receive, DMA, and link units.  It will not effect
+	 * the current PCI configuration.  The global reset bit is self-
+	 * clearing, and should clear within a microsecond.
+	 */
+	DEBUGOUT("Issuing a global reset to MAC\n");
+
+	switch(hw->mac_type) {
+		case e1000_82544:
+		case e1000_82540:
+		case e1000_82545:
+		case e1000_82546:
+		case e1000_82541:
+		case e1000_82541_rev_2:
+			/* These controllers can't ack the 64-bit write when issuing the
+			 * reset, so use IO-mapping as a workaround to issue the reset */
+			E1000_WRITE_REG_IO(hw, CTRL, (ctrl | E1000_CTRL_RST));
+			break;
+		case e1000_82545_rev_3:
+		case e1000_82546_rev_3:
+			/* Reset is performed on a shadow of the control register */
+			E1000_WRITE_REG(hw, CTRL_DUP, (ctrl | E1000_CTRL_RST));
+			break;
+		default:
+			E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST));
+			break;
+	}
+
+	/* After MAC reset, force reload of EEPROM to restore power-on settings to
+	 * device.  Later controllers reload the EEPROM automatically, so just wait
+	 * for reload to complete.
+	 */
+	switch(hw->mac_type) {
+		case e1000_82542_rev2_0:
+		case e1000_82542_rev2_1:
+		case e1000_82543:
+		case e1000_82544:
+			/* Wait for reset to complete */
+			udelay(10);
+			ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
+			ctrl_ext |= E1000_CTRL_EXT_EE_RST;
+			E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
+			E1000_WRITE_FLUSH(hw);
+			/* Wait for EEPROM reload */
+			mdelay(2);
+			break;
+		case e1000_82541:
+		case e1000_82541_rev_2:
+		case e1000_82547:
+		case e1000_82547_rev_2:
+			/* Wait for EEPROM reload */
+			mdelay(20);
+			break;
+		default:
+			/* Wait for EEPROM reload (it happens automatically) */
+			mdelay(5);
+			break;
+	}
+
+	/* Disable HW ARPs on ASF enabled adapters */
+	if(hw->mac_type >= e1000_82540) {
+		manc = E1000_READ_REG(hw, MANC);
+		manc &= ~(E1000_MANC_ARP_EN);
+		E1000_WRITE_REG(hw, MANC, manc);
+	}
+
+	if((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+		e1000_phy_init_script(hw);
+	}
+
+	/* Clear interrupt mask to stop board from generating interrupts */
+	DEBUGOUT("Masking off all interrupts\n");
+	E1000_WRITE_REG(hw, IMC, 0xffffffff);
+	
+	/* Clear any pending interrupt events. */
+	icr = E1000_READ_REG(hw, ICR);
+
+	/* If MWI was previously enabled, reenable it. */
+	if(hw->mac_type == e1000_82542_rev2_0) {
+#ifdef LINUX_DRIVER
+		if(hw->pci_cmd_word & CMD_MEM_WRT_INVALIDATE)
+#endif
+			e1000_pci_set_mwi(hw);
+	}
+}
+
+/******************************************************************************
+ * Performs basic configuration of the adapter.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * 
+ * Assumes that the controller has previously been reset and is in a 
+ * post-reset uninitialized state. Initializes the receive address registers,
+ * multicast table, and VLAN filter table. Calls routines to setup link
+ * configuration and flow control settings. Clears all on-chip counters. Leaves
+ * the transmit and receive units disabled and uninitialized.
+ *****************************************************************************/
+static int
+e1000_init_hw(struct e1000_hw *hw)
+{
+	uint32_t ctrl, status;
+	uint32_t i;
+	int32_t ret_val;
+	uint16_t pcix_cmd_word;
+	uint16_t pcix_stat_hi_word;
+	uint16_t cmd_mmrbc;
+	uint16_t stat_mmrbc;
+	e1000_bus_type bus_type = e1000_bus_type_unknown;
+
+	DEBUGFUNC("e1000_init_hw");
+
+	/* Set the media type and TBI compatibility */
+	e1000_set_media_type(hw);
+
+	/* Disabling VLAN filtering. */
+	DEBUGOUT("Initializing the IEEE VLAN\n");
+	E1000_WRITE_REG(hw, VET, 0);
+	
+	e1000_clear_vfta(hw);
+	
+	/* For 82542 (rev 2.0), disable MWI and put the receiver into reset */
+	if(hw->mac_type == e1000_82542_rev2_0) {
+		DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
+		e1000_pci_clear_mwi(hw);
+		E1000_WRITE_REG(hw, RCTL, E1000_RCTL_RST);
+		E1000_WRITE_FLUSH(hw);
+		mdelay(5);
+	}
+	
+	/* Setup the receive address. This involves initializing all of the Receive
+	 * Address Registers (RARs 0 - 15).
+	 */
+	e1000_init_rx_addrs(hw);
+	
+	/* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */
+	if(hw->mac_type == e1000_82542_rev2_0) {
+		E1000_WRITE_REG(hw, RCTL, 0);
+		E1000_WRITE_FLUSH(hw);
+		mdelay(1);
+#ifdef LINUX_DRIVER
+		if(hw->pci_cmd_word & CMD_MEM_WRT_INVALIDATE)
+#endif
+			e1000_pci_set_mwi(hw);
+	}
+	
+	/* Zero out the Multicast HASH table */
+	DEBUGOUT("Zeroing the MTA\n");
+	for(i = 0; i < E1000_MC_TBL_SIZE; i++)
+		E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
+	
+#if 0
+	/* Set the PCI priority bit correctly in the CTRL register.  This
+	 * determines if the adapter gives priority to receives, or if it
+	 * gives equal priority to transmits and receives.
+	 */
+	if(hw->dma_fairness) {
+		ctrl = E1000_READ_REG(hw, CTRL);
+		E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PRIOR);
+	}
+#endif
+
+	switch(hw->mac_type) {
+		case e1000_82545_rev_3:
+		case e1000_82546_rev_3:
+			break;
+		default:
+			if (hw->mac_type >= e1000_82543) {
+				/* See e1000_get_bus_info() of the Linux driver */
+				status = E1000_READ_REG(hw, STATUS);
+				bus_type = (status & E1000_STATUS_PCIX_MODE) ?
+					e1000_bus_type_pcix : e1000_bus_type_pci;
+			}
+
+			/* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */
+			if(bus_type == e1000_bus_type_pcix) {
+				pci_read_config_word(hw->pdev, PCIX_COMMAND_REGISTER, &pcix_cmd_word);
+				pci_read_config_word(hw->pdev, PCIX_STATUS_REGISTER_HI, &pcix_stat_hi_word);
+				cmd_mmrbc = (pcix_cmd_word & PCIX_COMMAND_MMRBC_MASK) >>
+					PCIX_COMMAND_MMRBC_SHIFT;
+				stat_mmrbc = (pcix_stat_hi_word & PCIX_STATUS_HI_MMRBC_MASK) >>
+					PCIX_STATUS_HI_MMRBC_SHIFT;
+				if(stat_mmrbc == PCIX_STATUS_HI_MMRBC_4K)
+					stat_mmrbc = PCIX_STATUS_HI_MMRBC_2K;
+				if(cmd_mmrbc > stat_mmrbc) {
+					pcix_cmd_word &= ~PCIX_COMMAND_MMRBC_MASK;
+					pcix_cmd_word |= stat_mmrbc << PCIX_COMMAND_MMRBC_SHIFT;
+					pci_write_config_word(hw->pdev, PCIX_COMMAND_REGISTER, pcix_cmd_word);
+				}
+			}
+			break;
+	}
+
+	/* Call a subroutine to configure the link and setup flow control. */
+	ret_val = e1000_setup_link(hw);
+	
+	/* Set the transmit descriptor write-back policy */
+	if(hw->mac_type > e1000_82544) {
+		ctrl = E1000_READ_REG(hw, TXDCTL);
+		ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB;
+		E1000_WRITE_REG(hw, TXDCTL, ctrl);
+	}
+
+#if 0
+	/* Clear all of the statistics registers (clear on read).  It is
+	 * important that we do this after we have tried to establish link
+	 * because the symbol error count will increment wildly if there
+	 * is no link.
+	 */
+	e1000_clear_hw_cntrs(hw);
+#endif
+
+	return ret_val;
+}
+
+/******************************************************************************
+ * Adjust SERDES output amplitude based on EEPROM setting.
+ *
+ * hw - Struct containing variables accessed by shared code.
+ *****************************************************************************/
+static int32_t
+e1000_adjust_serdes_amplitude(struct e1000_hw *hw)
+{
+	uint16_t eeprom_data;
+	int32_t  ret_val;
+
+	DEBUGFUNC("e1000_adjust_serdes_amplitude");
+
+	if(hw->media_type != e1000_media_type_internal_serdes)
+		return E1000_SUCCESS;
+
+	switch(hw->mac_type) {
+		case e1000_82545_rev_3:
+		case e1000_82546_rev_3:
+			break;
+		default:
+			return E1000_SUCCESS;
+	}
+
+	if ((ret_val = e1000_read_eeprom(hw, EEPROM_SERDES_AMPLITUDE, 1,
+					&eeprom_data))) {
+		return ret_val;
+	}
+
+	if(eeprom_data != EEPROM_RESERVED_WORD) {
+		/* Adjust SERDES output amplitude only. */
+		eeprom_data &= EEPROM_SERDES_AMPLITUDE_MASK;
+		if((ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_EXT_CTRL,
+		                                  eeprom_data)))
+			return ret_val;
+	}
+
+	return E1000_SUCCESS;
+}
+								   
+/******************************************************************************
+ * Configures flow control and link settings.
+ * 
+ * hw - Struct containing variables accessed by shared code
+ * 
+ * Determines which flow control settings to use. Calls the apropriate media-
+ * specific link configuration function. Configures the flow control settings.
+ * Assuming the adapter has a valid link partner, a valid link should be
+ * established. Assumes the hardware has previously been reset and the 
+ * transmitter and receiver are not enabled.
+ *****************************************************************************/
+static int
+e1000_setup_link(struct e1000_hw *hw)
+{
+	uint32_t ctrl_ext;
+	int32_t ret_val;
+	uint16_t eeprom_data;
+
+	DEBUGFUNC("e1000_setup_link");
+	
+	/* Read and store word 0x0F of the EEPROM. This word contains bits
+	 * that determine the hardware's default PAUSE (flow control) mode,
+	 * a bit that determines whether the HW defaults to enabling or
+	 * disabling auto-negotiation, and the direction of the
+	 * SW defined pins. If there is no SW over-ride of the flow
+	 * control setting, then the variable hw->fc will
+	 * be initialized based on a value in the EEPROM.
+	 */
+	if(e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data) < 0) {
+		DEBUGOUT("EEPROM Read Error\n");
+		return -E1000_ERR_EEPROM;
+	}
+	
+	if(hw->fc == e1000_fc_default) {
+		if((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
+			hw->fc = e1000_fc_none;
+		else if((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 
+			EEPROM_WORD0F_ASM_DIR)
+			hw->fc = e1000_fc_tx_pause;
+		else
+			hw->fc = e1000_fc_full;
+	}
+	
+	/* We want to save off the original Flow Control configuration just
+	 * in case we get disconnected and then reconnected into a different
+	 * hub or switch with different Flow Control capabilities.
+	 */
+	if(hw->mac_type == e1000_82542_rev2_0)
+		hw->fc &= (~e1000_fc_tx_pause);
+
+#if 0
+	/* See e1000_sw_init() of the Linux driver */
+	if((hw->mac_type < e1000_82543) && (hw->report_tx_early == 1))
+#else
+	if((hw->mac_type < e1000_82543) && (hw->mac_type >= e1000_82543))
+#endif
+		hw->fc &= (~e1000_fc_rx_pause);
+	
+#if 0
+	hw->original_fc = hw->fc;
+#endif
+
+	DEBUGOUT1("After fix-ups FlowControl is now = %x\n", hw->fc);
+	
+	/* Take the 4 bits from EEPROM word 0x0F that determine the initial
+	 * polarity value for the SW controlled pins, and setup the
+	 * Extended Device Control reg with that info.
+	 * This is needed because one of the SW controlled pins is used for
+	 * signal detection.  So this should be done before e1000_setup_pcs_link()
+	 * or e1000_phy_setup() is called.
+	 */
+	if(hw->mac_type == e1000_82543) {
+		ctrl_ext = ((eeprom_data & EEPROM_WORD0F_SWPDIO_EXT) << 
+			SWDPIO__EXT_SHIFT);
+		E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
+	}
+	
+	/* Call the necessary subroutine to configure the link. */
+	ret_val = (hw->media_type == e1000_media_type_copper) ?
+		e1000_setup_copper_link(hw) :
+		e1000_setup_fiber_serdes_link(hw);
+	if (ret_val < 0) {
+		return ret_val;
+	}
+	
+	/* Initialize the flow control address, type, and PAUSE timer
+	 * registers to their default values.  This is done even if flow
+	 * control is disabled, because it does not hurt anything to
+	 * initialize these registers.
+	 */
+	DEBUGOUT("Initializing the Flow Control address, type and timer regs\n");
+	
+	E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW);
+	E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH);
+	E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE);
+#if 0
+	E1000_WRITE_REG(hw, FCTTV, hw->fc_pause_time);
+#else
+	E1000_WRITE_REG(hw, FCTTV, FC_DEFAULT_TX_TIMER);
+#endif
+	
+	/* Set the flow control receive threshold registers.  Normally,
+	 * these registers will be set to a default threshold that may be
+	 * adjusted later by the driver's runtime code.  However, if the
+	 * ability to transmit pause frames in not enabled, then these
+	 * registers will be set to 0. 
+	 */
+	if(!(hw->fc & e1000_fc_tx_pause)) {
+		E1000_WRITE_REG(hw, FCRTL, 0);
+		E1000_WRITE_REG(hw, FCRTH, 0);
+	} else {
+		/* We need to set up the Receive Threshold high and low water marks
+		 * as well as (optionally) enabling the transmission of XON frames.
+		 */
+#if 0
+		if(hw->fc_send_xon) {
+			E1000_WRITE_REG(hw, FCRTL, (hw->fc_low_water | E1000_FCRTL_XONE));
+			E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water);
+		} else {
+			E1000_WRITE_REG(hw, FCRTL, hw->fc_low_water);
+			E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water);
+		}
+#else
+		E1000_WRITE_REG(hw, FCRTL, (FC_DEFAULT_LO_THRESH | E1000_FCRTL_XONE));
+		E1000_WRITE_REG(hw, FCRTH, FC_DEFAULT_HI_THRESH);
+#endif
+	}
+	return ret_val;
+}
+
+/******************************************************************************
+ * Sets up link for a fiber based or serdes based adapter
+ *
+ * hw - Struct containing variables accessed by shared code
+ *
+ * Manipulates Physical Coding Sublayer functions in order to configure
+ * link. Assumes the hardware has been previously reset and the transmitter
+ * and receiver are not enabled.
+ *****************************************************************************/
+static int
+e1000_setup_fiber_serdes_link(struct e1000_hw *hw)
+{
+	uint32_t ctrl;
+	uint32_t status;
+	uint32_t txcw = 0;
+	uint32_t i;
+	uint32_t signal = 0;
+	int32_t ret_val;
+
+	DEBUGFUNC("e1000_setup_fiber_serdes_link");
+
+	/* On adapters with a MAC newer than 82544, SW Defineable pin 1 will be 
+	 * set when the optics detect a signal. On older adapters, it will be 
+	 * cleared when there is a signal.  This applies to fiber media only.
+	 * If we're on serdes media, adjust the output amplitude to value set in
+	 * the EEPROM.
+	 */
+	ctrl = E1000_READ_REG(hw, CTRL);
+	if(hw->media_type == e1000_media_type_fiber)
+		signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0;
+
+	if((ret_val = e1000_adjust_serdes_amplitude(hw)))
+		return ret_val;
+
+	/* Take the link out of reset */
+	ctrl &= ~(E1000_CTRL_LRST);
+
+#if 0
+	/* Adjust VCO speed to improve BER performance */
+	if((ret_val = e1000_set_vco_speed(hw)))
+		return ret_val;
+#endif
+
+	e1000_config_collision_dist(hw);
+	
+	/* Check for a software override of the flow control settings, and setup
+	 * the device accordingly.  If auto-negotiation is enabled, then software
+	 * will have to set the "PAUSE" bits to the correct value in the Tranmsit
+	 * Config Word Register (TXCW) and re-start auto-negotiation.  However, if
+	 * auto-negotiation is disabled, then software will have to manually 
+	 * configure the two flow control enable bits in the CTRL register.
+	 *
+	 * The possible values of the "fc" parameter are:
+	 *      0:  Flow control is completely disabled
+	 *      1:  Rx flow control is enabled (we can receive pause frames, but 
+	 *          not send pause frames).
+	 *      2:  Tx flow control is enabled (we can send pause frames but we do
+	 *          not support receiving pause frames).
+	 *      3:  Both Rx and TX flow control (symmetric) are enabled.
+	 */
+	switch (hw->fc) {
+	case e1000_fc_none:
+		/* Flow control is completely disabled by a software over-ride. */
+		txcw = (E1000_TXCW_ANE | E1000_TXCW_FD);
+		break;
+	case e1000_fc_rx_pause:
+		/* RX Flow control is enabled and TX Flow control is disabled by a 
+		 * software over-ride. Since there really isn't a way to advertise 
+		 * that we are capable of RX Pause ONLY, we will advertise that we
+		 * support both symmetric and asymmetric RX PAUSE. Later, we will
+		 *  disable the adapter's ability to send PAUSE frames.
+		 */
+		txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
+		break;
+	case e1000_fc_tx_pause:
+		/* TX Flow control is enabled, and RX Flow control is disabled, by a 
+		 * software over-ride.
+		 */
+		txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR);
+		break;
+	case e1000_fc_full:
+		/* Flow control (both RX and TX) is enabled by a software over-ride. */
+		txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
+		break;
+	default:
+		DEBUGOUT("Flow control param set incorrectly\n");
+		return -E1000_ERR_CONFIG;
+		break;
+	}
+	
+	/* Since auto-negotiation is enabled, take the link out of reset (the link
+	 * will be in reset, because we previously reset the chip). This will
+	 * restart auto-negotiation.  If auto-neogtiation is successful then the
+	 * link-up status bit will be set and the flow control enable bits (RFCE
+	 * and TFCE) will be set according to their negotiated value.
+	 */
+	DEBUGOUT("Auto-negotiation enabled\n");
+	
+	E1000_WRITE_REG(hw, TXCW, txcw);
+	E1000_WRITE_REG(hw, CTRL, ctrl);
+	E1000_WRITE_FLUSH(hw);
+	
+	hw->txcw = txcw;
+	mdelay(1);
+	
+	/* If we have a signal (the cable is plugged in) then poll for a "Link-Up"
+	 * indication in the Device Status Register.  Time-out if a link isn't 
+	 * seen in 500 milliseconds seconds (Auto-negotiation should complete in 
+	 * less than 500 milliseconds even if the other end is doing it in SW).
+	 * For internal serdes, we just assume a signal is present, then poll.
+	 */
+	if(hw->media_type == e1000_media_type_internal_serdes ||
+	   (E1000_READ_REG(hw, CTRL) & E1000_CTRL_SWDPIN1) == signal) {
+		DEBUGOUT("Looking for Link\n");
+		for(i = 0; i < (LINK_UP_TIMEOUT / 10); i++) {
+			mdelay(10);
+			status = E1000_READ_REG(hw, STATUS);
+			if(status & E1000_STATUS_LU) break;
+		}
+		if(i == (LINK_UP_TIMEOUT / 10)) {
+			DEBUGOUT("Never got a valid link from auto-neg!!!\n");
+			hw->autoneg_failed = 1;
+			/* AutoNeg failed to achieve a link, so we'll call 
+			 * e1000_check_for_link. This routine will force the link up if
+			 * we detect a signal. This will allow us to communicate with
+			 * non-autonegotiating link partners.
+			 */
+			if((ret_val = e1000_check_for_link(hw))) {
+				DEBUGOUT("Error while checking for link\n");
+				return ret_val;
+			}
+			hw->autoneg_failed = 0;
+		} else {
+			hw->autoneg_failed = 0;
+			DEBUGOUT("Valid Link Found\n");
+		}
+	} else {
+		DEBUGOUT("No Signal Detected\n");
+	}
+	return E1000_SUCCESS;
+}
+
+/******************************************************************************
+* Detects which PHY is present and the speed and duplex
+*
+* hw - Struct containing variables accessed by shared code
+******************************************************************************/
+static int
+e1000_setup_copper_link(struct e1000_hw *hw)
+{
+	uint32_t ctrl;
+	int32_t ret_val;
+	uint16_t i;
+	uint16_t phy_data;
+	
+	DEBUGFUNC("e1000_setup_copper_link");
+	
+	ctrl = E1000_READ_REG(hw, CTRL);
+	/* With 82543, we need to force speed and duplex on the MAC equal to what
+	 * the PHY speed and duplex configuration is. In addition, we need to
+	 * perform a hardware reset on the PHY to take it out of reset.
+	 */
+	if(hw->mac_type > e1000_82543) {
+		ctrl |= E1000_CTRL_SLU;
+		ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+		E1000_WRITE_REG(hw, CTRL, ctrl);
+	} else {
+		ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX | E1000_CTRL_SLU);
+		E1000_WRITE_REG(hw, CTRL, ctrl);
+		e1000_phy_hw_reset(hw);
+	}
+	
+	/* Make sure we have a valid PHY */
+	if((ret_val = e1000_detect_gig_phy(hw))) {
+		DEBUGOUT("Error, did not detect valid phy.\n");
+		return ret_val;
+	}
+	DEBUGOUT1("Phy ID = %x \n", hw->phy_id);
+
+	if(hw->mac_type <= e1000_82543 ||
+	   hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 ||
+#if 0
+	   hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2)
+		hw->phy_reset_disable = FALSE;
+
+	if(!hw->phy_reset_disable) {
+#else
+	   hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2) {
+#endif
+	if (hw->phy_type == e1000_phy_igp) {
+
+		if((ret_val = e1000_phy_reset(hw))) {
+			DEBUGOUT("Error Resetting the PHY\n");
+			return ret_val;
+		}
+
+		/* Wait 10ms for MAC to configure PHY from eeprom settings */
+		mdelay(15);
+
+#if 0
+		/* disable lplu d3 during driver init */
+		if((ret_val = e1000_set_d3_lplu_state(hw, FALSE))) {
+			DEBUGOUT("Error Disabling LPLU D3\n");
+			return ret_val;
+		}
+
+		/* Configure mdi-mdix settings */
+		if((ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL,
+		                                 &phy_data)))
+			return ret_val;
+
+		if((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+			hw->dsp_config_state = e1000_dsp_config_disabled;
+			/* Force MDI for IGP B-0 PHY */
+			phy_data &= ~(IGP01E1000_PSCR_AUTO_MDIX |
+			              IGP01E1000_PSCR_FORCE_MDI_MDIX);
+			hw->mdix = 1;
+
+		} else {
+			hw->dsp_config_state = e1000_dsp_config_enabled;
+			phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
+
+			switch (hw->mdix) {
+			case 1:
+				phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
+				break;
+			case 2:
+				phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX;
+				break;
+			case 0:
+			default:
+				phy_data |= IGP01E1000_PSCR_AUTO_MDIX;
+				break;
+			}
+		}
+		if((ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL,
+		                                  phy_data)))
+			return ret_val;
+
+		/* set auto-master slave resolution settings */
+		e1000_ms_type phy_ms_setting = hw->master_slave;
+
+		if(hw->ffe_config_state == e1000_ffe_config_active)
+			hw->ffe_config_state = e1000_ffe_config_enabled;
+
+		if(hw->dsp_config_state == e1000_dsp_config_activated)
+			hw->dsp_config_state = e1000_dsp_config_enabled;
+#endif
+
+		/* when autonegotiation advertisment is only 1000Mbps then we
+		 * should disable SmartSpeed and enable Auto MasterSlave
+		 * resolution as hardware default. */
+		if(hw->autoneg_advertised == ADVERTISE_1000_FULL) {
+			/* Disable SmartSpeed */
+			if((ret_val = e1000_read_phy_reg(hw,
+			                                 IGP01E1000_PHY_PORT_CONFIG,
+			                                 &phy_data)))
+				return ret_val;
+			phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+			if((ret_val = e1000_write_phy_reg(hw,
+			                                  IGP01E1000_PHY_PORT_CONFIG,
+			                                  phy_data)))
+				return ret_val;
+			/* Set auto Master/Slave resolution process */
+			if((ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL,
+			                                 &phy_data)))
+				return ret_val;
+			phy_data &= ~CR_1000T_MS_ENABLE;
+			if((ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL,
+			                                  phy_data)))
+				return ret_val;
+		}
+
+		if((ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL,
+		                                 &phy_data)))
+			return ret_val;
+
+#if 0
+		/* load defaults for future use */
+		hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ?
+		                            ((phy_data & CR_1000T_MS_VALUE) ?
+		                             e1000_ms_force_master :
+		                             e1000_ms_force_slave) :
+		                             e1000_ms_auto;
+
+		switch (phy_ms_setting) {
+		case e1000_ms_force_master:
+			phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE);
+			break;
+		case e1000_ms_force_slave:
+			phy_data |= CR_1000T_MS_ENABLE;
+			phy_data &= ~(CR_1000T_MS_VALUE);
+			break;
+		case e1000_ms_auto:
+			phy_data &= ~CR_1000T_MS_ENABLE;
+		default:
+			break;
+		}
+#endif
+
+		if((ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL,
+		                                  phy_data)))
+			return ret_val;
+	} else {
+		/* Enable CRS on TX. This must be set for half-duplex operation. */
+		if((ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL,
+		                                 &phy_data)))
+			return ret_val;
+
+		phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
+
+		/* Options:
+		 *   MDI/MDI-X = 0 (default)
+		 *   0 - Auto for all speeds
+		 *   1 - MDI mode
+		 *   2 - MDI-X mode
+		 *   3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
+		 */
+#if 0
+		phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
+
+		switch (hw->mdix) {
+		case 1:
+			phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE;
+			break;
+		case 2:
+			phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE;
+			break;
+		case 3:
+			phy_data |= M88E1000_PSCR_AUTO_X_1000T;
+			break;
+		case 0:
+		default:
+#endif
+			phy_data |= M88E1000_PSCR_AUTO_X_MODE;
+#if 0
+			break;
+		}
+#endif
+
+		/* Options:
+		 *   disable_polarity_correction = 0 (default)
+		 *       Automatic Correction for Reversed Cable Polarity
+		 *   0 - Disabled
+		 *   1 - Enabled
+		 */
+		phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
+		if((ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL,
+		                                  phy_data)))
+			return ret_val;
+
+		/* Force TX_CLK in the Extended PHY Specific Control Register
+		 * to 25MHz clock.
+		 */
+		if((ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+		                                 &phy_data)))
+			return ret_val;
+
+		phy_data |= M88E1000_EPSCR_TX_CLK_25;
+
+#ifdef LINUX_DRIVER
+		if (hw->phy_revision < M88E1011_I_REV_4) {
+#endif
+			/* Configure Master and Slave downshift values */
+			phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK |
+				M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK);
+			phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X |
+				M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X);
+			if((ret_val = e1000_write_phy_reg(hw,
+			                                  M88E1000_EXT_PHY_SPEC_CTRL,
+			                                  phy_data)))
+				return ret_val;
+		}
+	
+		/* SW Reset the PHY so all changes take effect */
+		if((ret_val = e1000_phy_reset(hw))) {
+			DEBUGOUT("Error Resetting the PHY\n");
+			return ret_val;
+#ifdef LINUX_DRIVER
+		}
+#endif
+	}
+	
+	/* Options:
+	 *   autoneg = 1 (default)
+	 *      PHY will advertise value(s) parsed from
+	 *      autoneg_advertised and fc
+	 *   autoneg = 0
+	 *      PHY will be set to 10H, 10F, 100H, or 100F
+	 *      depending on value parsed from forced_speed_duplex.
+	 */
+	
+	/* Is autoneg enabled?  This is enabled by default or by software
+	 * override.  If so, call e1000_phy_setup_autoneg routine to parse the
+	 * autoneg_advertised and fc options. If autoneg is NOT enabled, then
+	 * the user should have provided a speed/duplex override.  If so, then
+	 * call e1000_phy_force_speed_duplex to parse and set this up.
+	 */
+	/* Perform some bounds checking on the hw->autoneg_advertised
+	 * parameter.  If this variable is zero, then set it to the default.
+	 */
+	hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT;
+	
+	/* If autoneg_advertised is zero, we assume it was not defaulted
+	 * by the calling code so we set to advertise full capability.
+	 */
+	if(hw->autoneg_advertised == 0)
+		hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+	
+	DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
+	if((ret_val = e1000_phy_setup_autoneg(hw))) {
+		DEBUGOUT("Error Setting up Auto-Negotiation\n");
+		return ret_val;
+	}
+	DEBUGOUT("Restarting Auto-Neg\n");
+	
+	/* Restart auto-negotiation by setting the Auto Neg Enable bit and
+	 * the Auto Neg Restart bit in the PHY control register.
+	 */
+	if((ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data)))
+		return ret_val;
+
+	phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
+	if((ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data)))
+		return ret_val;
+
+#if 0	
+	/* Does the user want to wait for Auto-Neg to complete here, or
+	 * check at a later time (for example, callback routine).
+	 */
+	if(hw->wait_autoneg_complete) {
+		if((ret_val = e1000_wait_autoneg(hw))) {
+			DEBUGOUT("Error while waiting for autoneg to complete\n");
+			return ret_val;
+		}
+	}
+#else
+	/* If we do not wait for autonegotiation to complete I 
+	 * do not see a valid link status.
+	 */
+	if((ret_val = e1000_wait_autoneg(hw))) {
+		DEBUGOUT("Error while waiting for autoneg to complete\n");
+		return ret_val;
+	}
+#endif
+	} /* !hw->phy_reset_disable */
+	
+	/* Check link status. Wait up to 100 microseconds for link to become
+	 * valid.
+	 */
+	for(i = 0; i < 10; i++) {
+		if((ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data)))
+			return ret_val;
+		if((ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data)))
+			return ret_val;
+
+		if(phy_data & MII_SR_LINK_STATUS) {
+			/* We have link, so we need to finish the config process:
+			 *   1) Set up the MAC to the current PHY speed/duplex
+			 *      if we are on 82543.  If we
+			 *      are on newer silicon, we only need to configure
+			 *      collision distance in the Transmit Control Register.
+			 *   2) Set up flow control on the MAC to that established with
+			 *      the link partner.
+			 */
+			if(hw->mac_type >= e1000_82544) {
+				e1000_config_collision_dist(hw);
+			} else {
+				if((ret_val = e1000_config_mac_to_phy(hw))) {
+					DEBUGOUT("Error configuring MAC to PHY settings\n");
+					return ret_val;
+				}
+			}
+			if((ret_val = e1000_config_fc_after_link_up(hw))) {
+				DEBUGOUT("Error Configuring Flow Control\n");
+				return ret_val;
+			}
+#if 0
+			if(hw->phy_type == e1000_phy_igp) {
+				if((ret_val = e1000_config_dsp_after_link_change(hw, TRUE))) {
+					DEBUGOUT("Error Configuring DSP after link up\n");
+					return ret_val;
+				}
+			}
+#endif
+			DEBUGOUT("Valid link established!!!\n");
+			return E1000_SUCCESS;
+		}
+		udelay(10);
+	}
+	
+	DEBUGOUT("Unable to establish link!!!\n");
+	return -E1000_ERR_NOLINK;
+}
+
+/******************************************************************************
+* Configures PHY autoneg and flow control advertisement settings
+*
+* hw - Struct containing variables accessed by shared code
+******************************************************************************/
+static int
+e1000_phy_setup_autoneg(struct e1000_hw *hw)
+{
+	int32_t ret_val;
+	uint16_t mii_autoneg_adv_reg;
+	uint16_t mii_1000t_ctrl_reg;
+
+	DEBUGFUNC("e1000_phy_setup_autoneg");
+	
+	/* Read the MII Auto-Neg Advertisement Register (Address 4). */
+	if((ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV,
+	                                 &mii_autoneg_adv_reg)))
+		return ret_val;
+
+	/* Read the MII 1000Base-T Control Register (Address 9). */
+	if((ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg)))
+		return ret_val;
+
+	/* Need to parse both autoneg_advertised and fc and set up
+	 * the appropriate PHY registers.  First we will parse for
+	 * autoneg_advertised software override.  Since we can advertise
+	 * a plethora of combinations, we need to check each bit
+	 * individually.
+	 */
+	
+	/* First we clear all the 10/100 mb speed bits in the Auto-Neg
+	 * Advertisement Register (Address 4) and the 1000 mb speed bits in
+	 * the  1000Base-T Control Register (Address 9).
+	 */
+	mii_autoneg_adv_reg &= ~REG4_SPEED_MASK;
+	mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK;
+
+	DEBUGOUT1("autoneg_advertised %x\n", hw->autoneg_advertised);
+
+	/* Do we want to advertise 10 Mb Half Duplex? */
+	if(hw->autoneg_advertised & ADVERTISE_10_HALF) {
+		DEBUGOUT("Advertise 10mb Half duplex\n");
+		mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
+	}
+
+	/* Do we want to advertise 10 Mb Full Duplex? */
+	if(hw->autoneg_advertised & ADVERTISE_10_FULL) {
+		DEBUGOUT("Advertise 10mb Full duplex\n");
+		mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
+	}
+
+	/* Do we want to advertise 100 Mb Half Duplex? */
+	if(hw->autoneg_advertised & ADVERTISE_100_HALF) {
+		DEBUGOUT("Advertise 100mb Half duplex\n");
+		mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
+	}
+
+	/* Do we want to advertise 100 Mb Full Duplex? */
+	if(hw->autoneg_advertised & ADVERTISE_100_FULL) {
+		DEBUGOUT("Advertise 100mb Full duplex\n");
+		mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
+	}
+
+	/* We do not allow the Phy to advertise 1000 Mb Half Duplex */
+	if(hw->autoneg_advertised & ADVERTISE_1000_HALF) {
+		DEBUGOUT("Advertise 1000mb Half duplex requested, request denied!\n");
+	}
+
+	/* Do we want to advertise 1000 Mb Full Duplex? */
+	if(hw->autoneg_advertised & ADVERTISE_1000_FULL) {
+		DEBUGOUT("Advertise 1000mb Full duplex\n");
+		mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
+	}
+
+	/* Check for a software override of the flow control settings, and
+	 * setup the PHY advertisement registers accordingly.  If
+	 * auto-negotiation is enabled, then software will have to set the
+	 * "PAUSE" bits to the correct value in the Auto-Negotiation
+	 * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation.
+	 *
+	 * The possible values of the "fc" parameter are:
+	 *      0:  Flow control is completely disabled
+	 *      1:  Rx flow control is enabled (we can receive pause frames
+	 *          but not send pause frames).
+	 *      2:  Tx flow control is enabled (we can send pause frames
+	 *          but we do not support receiving pause frames).
+	 *      3:  Both Rx and TX flow control (symmetric) are enabled.
+	 *  other:  No software override.  The flow control configuration
+	 *          in the EEPROM is used.
+	 */
+	switch (hw->fc) {
+	case e1000_fc_none: /* 0 */
+		/* Flow control (RX & TX) is completely disabled by a
+		 * software over-ride.
+		 */
+		mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+		break;
+	case e1000_fc_rx_pause: /* 1 */
+		/* RX Flow control is enabled, and TX Flow control is
+		 * disabled, by a software over-ride.
+		 */
+		/* Since there really isn't a way to advertise that we are
+		 * capable of RX Pause ONLY, we will advertise that we
+		 * support both symmetric and asymmetric RX PAUSE.  Later
+		 * (in e1000_config_fc_after_link_up) we will disable the
+		 *hw's ability to send PAUSE frames.
+		 */
+		mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+		break;
+	case e1000_fc_tx_pause: /* 2 */
+		/* TX Flow control is enabled, and RX Flow control is
+		 * disabled, by a software over-ride.
+		 */
+		mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
+		mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
+		break;
+	case e1000_fc_full: /* 3 */
+		/* Flow control (both RX and TX) is enabled by a software
+		 * over-ride.
+		 */
+		mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+		break;
+	default:
+		DEBUGOUT("Flow control param set incorrectly\n");
+		return -E1000_ERR_CONFIG;
+	}
+
+	if((ret_val = e1000_write_phy_reg(hw, PHY_AUTONEG_ADV,
+	                       mii_autoneg_adv_reg)))
+		return ret_val;
+
+	DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
+
+	if((ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg)))
+		return ret_val;
+
+	return E1000_SUCCESS;
+}
+
+/******************************************************************************
+* Sets the collision distance in the Transmit Control register
+*
+* hw - Struct containing variables accessed by shared code
+*
+* Link should have been established previously. Reads the speed and duplex
+* information from the Device Status register.
+******************************************************************************/
+static void
+e1000_config_collision_dist(struct e1000_hw *hw)
+{
+	uint32_t tctl;
+
+	tctl = E1000_READ_REG(hw, TCTL);
+	
+	tctl &= ~E1000_TCTL_COLD;
+	tctl |= E1000_COLLISION_DISTANCE << E1000_COLD_SHIFT;
+	
+	E1000_WRITE_REG(hw, TCTL, tctl);
+	E1000_WRITE_FLUSH(hw);
+}
+
+/******************************************************************************
+* Sets MAC speed and duplex settings to reflect the those in the PHY
+*
+* hw - Struct containing variables accessed by shared code
+* mii_reg - data to write to the MII control register
+*
+* The contents of the PHY register containing the needed information need to
+* be passed in.
+******************************************************************************/
+static int
+e1000_config_mac_to_phy(struct e1000_hw *hw)
+{
+	uint32_t ctrl;
+	int32_t ret_val;
+	uint16_t phy_data;
+
+	DEBUGFUNC("e1000_config_mac_to_phy");
+
+	/* Read the Device Control Register and set the bits to Force Speed
+	 * and Duplex.
+	 */
+	ctrl = E1000_READ_REG(hw, CTRL);
+	ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+	ctrl &= ~(E1000_CTRL_SPD_SEL | E1000_CTRL_ILOS);
+
+	/* Set up duplex in the Device Control and Transmit Control
+	 * registers depending on negotiated values.
+	 */
+	if (hw->phy_type == e1000_phy_igp) {
+		if((ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS,
+		                                 &phy_data)))
+			return ret_val;
+
+		if(phy_data & IGP01E1000_PSSR_FULL_DUPLEX) ctrl |= E1000_CTRL_FD;
+		else ctrl &= ~E1000_CTRL_FD;
+
+		e1000_config_collision_dist(hw);
+
+		/* Set up speed in the Device Control register depending on
+		 * negotiated values.
+		 */
+		if((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
+		   IGP01E1000_PSSR_SPEED_1000MBPS)
+			ctrl |= E1000_CTRL_SPD_1000;
+		else if((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
+			IGP01E1000_PSSR_SPEED_100MBPS)
+			ctrl |= E1000_CTRL_SPD_100;
+	} else {
+		if((ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
+		                                 &phy_data)))
+			return ret_val;
+		
+		if(phy_data & M88E1000_PSSR_DPLX) ctrl |= E1000_CTRL_FD;
+		else ctrl &= ~E1000_CTRL_FD;
+
+		e1000_config_collision_dist(hw);
+
+		/* Set up speed in the Device Control register depending on
+		 * negotiated values.
+		 */
+		if((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS)
+			ctrl |= E1000_CTRL_SPD_1000;
+		else if((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS)
+			ctrl |= E1000_CTRL_SPD_100;
+	}
+	/* Write the configured values back to the Device Control Reg. */
+	E1000_WRITE_REG(hw, CTRL, ctrl);
+	return E1000_SUCCESS;
+}
+
+/******************************************************************************
+ * Forces the MAC's flow control settings.
+ * 
+ * hw - Struct containing variables accessed by shared code
+ *
+ * Sets the TFCE and RFCE bits in the device control register to reflect
+ * the adapter settings. TFCE and RFCE need to be explicitly set by
+ * software when a Copper PHY is used because autonegotiation is managed
+ * by the PHY rather than the MAC. Software must also configure these
+ * bits when link is forced on a fiber connection.
+ *****************************************************************************/
+static int
+e1000_force_mac_fc(struct e1000_hw *hw)
+{
+	uint32_t ctrl;
+	
+	DEBUGFUNC("e1000_force_mac_fc");
+	
+	/* Get the current configuration of the Device Control Register */
+	ctrl = E1000_READ_REG(hw, CTRL);
+	
+	/* Because we didn't get link via the internal auto-negotiation
+	 * mechanism (we either forced link or we got link via PHY
+	 * auto-neg), we have to manually enable/disable transmit an
+	 * receive flow control.
+	 *
+	 * The "Case" statement below enables/disable flow control
+	 * according to the "hw->fc" parameter.
+	 *
+	 * The possible values of the "fc" parameter are:
+	 *      0:  Flow control is completely disabled
+	 *      1:  Rx flow control is enabled (we can receive pause
+	 *          frames but not send pause frames).
+	 *      2:  Tx flow control is enabled (we can send pause frames
+	 *          frames but we do not receive pause frames).
+	 *      3:  Both Rx and TX flow control (symmetric) is enabled.
+	 *  other:  No other values should be possible at this point.
+	 */
+	
+	switch (hw->fc) {
+	case e1000_fc_none:
+		ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
+		break;
+	case e1000_fc_rx_pause:
+		ctrl &= (~E1000_CTRL_TFCE);
+		ctrl |= E1000_CTRL_RFCE;
+		break;
+	case e1000_fc_tx_pause:
+		ctrl &= (~E1000_CTRL_RFCE);
+		ctrl |= E1000_CTRL_TFCE;
+		break;
+	case e1000_fc_full:
+		ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE);
+		break;
+	default:
+		DEBUGOUT("Flow control param set incorrectly\n");
+		return -E1000_ERR_CONFIG;
+	}
+	
+	/* Disable TX Flow Control for 82542 (rev 2.0) */
+	if(hw->mac_type == e1000_82542_rev2_0)
+		ctrl &= (~E1000_CTRL_TFCE);
+	
+	E1000_WRITE_REG(hw, CTRL, ctrl);
+	return E1000_SUCCESS;
+}
+
+/******************************************************************************
+ * Configures flow control settings after link is established
+ * 
+ * hw - Struct containing variables accessed by shared code
+ *
+ * Should be called immediately after a valid link has been established.
+ * Forces MAC flow control settings if link was forced. When in MII/GMII mode
+ * and autonegotiation is enabled, the MAC flow control settings will be set
+ * based on the flow control negotiated by the PHY. In TBI mode, the TFCE
+ * and RFCE bits will be automaticaly set to the negotiated flow control mode.
+ *****************************************************************************/
+static int
+e1000_config_fc_after_link_up(struct e1000_hw *hw)
+{
+	int32_t ret_val;
+	uint16_t mii_status_reg;
+	uint16_t mii_nway_adv_reg;
+	uint16_t mii_nway_lp_ability_reg;
+	uint16_t speed;
+	uint16_t duplex;
+	
+	DEBUGFUNC("e1000_config_fc_after_link_up");
+	
+	/* Check for the case where we have fiber media and auto-neg failed
+	 * so we had to force link.  In this case, we need to force the
+	 * configuration of the MAC to match the "fc" parameter.
+	 */
+	if(((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed)) ||
+	   ((hw->media_type == e1000_media_type_internal_serdes) && (hw->autoneg_failed))) { 
+		if((ret_val = e1000_force_mac_fc(hw))) {
+			DEBUGOUT("Error forcing flow control settings\n");
+			return ret_val;
+		}
+	}
+	
+	/* Check for the case where we have copper media and auto-neg is
+	 * enabled.  In this case, we need to check and see if Auto-Neg
+	 * has completed, and if so, how the PHY and link partner has
+	 * flow control configured.
+	 */
+	if(hw->media_type == e1000_media_type_copper) {
+		/* Read the MII Status Register and check to see if AutoNeg
+		 * has completed.  We read this twice because this reg has
+		 * some "sticky" (latched) bits.
+		 */
+		if((ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg)))
+			return ret_val;
+		if((ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg)))
+			return ret_val;
+		
+		if(mii_status_reg & MII_SR_AUTONEG_COMPLETE) {
+			/* The AutoNeg process has completed, so we now need to
+			 * read both the Auto Negotiation Advertisement Register
+			 * (Address 4) and the Auto_Negotiation Base Page Ability
+			 * Register (Address 5) to determine how flow control was
+			 * negotiated.
+			 */
+			if((ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV,
+			                                 &mii_nway_adv_reg)))
+				return ret_val;
+			if((ret_val = e1000_read_phy_reg(hw, PHY_LP_ABILITY,
+			                                 &mii_nway_lp_ability_reg)))
+				return ret_val;
+
+			/* Two bits in the Auto Negotiation Advertisement Register
+			 * (Address 4) and two bits in the Auto Negotiation Base
+			 * Page Ability Register (Address 5) determine flow control
+			 * for both the PHY and the link partner.  The following
+			 * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
+			 * 1999, describes these PAUSE resolution bits and how flow
+			 * control is determined based upon these settings.
+			 * NOTE:  DC = Don't Care
+			 *
+			 *   LOCAL DEVICE  |   LINK PARTNER
+			 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
+			 *-------|---------|-------|---------|--------------------
+			 *   0   |    0    |  DC   |   DC    | e1000_fc_none
+			 *   0   |    1    |   0   |   DC    | e1000_fc_none
+			 *   0   |    1    |   1   |    0    | e1000_fc_none
+			 *   0   |    1    |   1   |    1    | e1000_fc_tx_pause
+			 *   1   |    0    |   0   |   DC    | e1000_fc_none
+			 *   1   |   DC    |   1   |   DC    | e1000_fc_full
+			 *   1   |    1    |   0   |    0    | e1000_fc_none
+			 *   1   |    1    |   0   |    1    | e1000_fc_rx_pause
+			 *
+			 */
+			/* Are both PAUSE bits set to 1?  If so, this implies
+			 * Symmetric Flow Control is enabled at both ends.  The
+			 * ASM_DIR bits are irrelevant per the spec.
+			 *
+			 * For Symmetric Flow Control:
+			 *
+			 *   LOCAL DEVICE  |   LINK PARTNER
+			 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+			 *-------|---------|-------|---------|--------------------
+			 *   1   |   DC    |   1   |   DC    | e1000_fc_full
+			 *
+			 */
+			if((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+				(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
+				/* Now we need to check if the user selected RX ONLY
+				 * of pause frames.  In this case, we had to advertise
+				 * FULL flow control because we could not advertise RX
+				 * ONLY. Hence, we must now check to see if we need to
+				 * turn OFF  the TRANSMISSION of PAUSE frames.
+				 */
+#if 0
+				if(hw->original_fc == e1000_fc_full) {
+					hw->fc = e1000_fc_full;
+#else
+				if(hw->fc == e1000_fc_full) {
+#endif
+					DEBUGOUT("Flow Control = FULL.\r\n");
+				} else {
+					hw->fc = e1000_fc_rx_pause;
+					DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n");
+				}
+			}
+			/* For receiving PAUSE frames ONLY.
+			 *
+			 *   LOCAL DEVICE  |   LINK PARTNER
+			 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+			 *-------|---------|-------|---------|--------------------
+			 *   0   |    1    |   1   |    1    | e1000_fc_tx_pause
+			 *
+			 */
+			else if(!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+				(mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+				(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+				(mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+				hw->fc = e1000_fc_tx_pause;
+				DEBUGOUT("Flow Control = TX PAUSE frames only.\r\n");
+			}
+			/* For transmitting PAUSE frames ONLY.
+			 *
+			 *   LOCAL DEVICE  |   LINK PARTNER
+			 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+			 *-------|---------|-------|---------|--------------------
+			 *   1   |    1    |   0   |    1    | e1000_fc_rx_pause
+			 *
+			 */
+			else if((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+				(mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+				!(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+				(mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+				hw->fc = e1000_fc_rx_pause;
+				DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n");
+			}
+			/* Per the IEEE spec, at this point flow control should be
+			 * disabled.  However, we want to consider that we could
+			 * be connected to a legacy switch that doesn't advertise
+			 * desired flow control, but can be forced on the link
+			 * partner.  So if we advertised no flow control, that is
+			 * what we will resolve to.  If we advertised some kind of
+			 * receive capability (Rx Pause Only or Full Flow Control)
+			 * and the link partner advertised none, we will configure
+			 * ourselves to enable Rx Flow Control only.  We can do
+			 * this safely for two reasons:  If the link partner really
+			 * didn't want flow control enabled, and we enable Rx, no
+			 * harm done since we won't be receiving any PAUSE frames
+			 * anyway.  If the intent on the link partner was to have
+			 * flow control enabled, then by us enabling RX only, we
+			 * can at least receive pause frames and process them.
+			 * This is a good idea because in most cases, since we are
+			 * predominantly a server NIC, more times than not we will
+			 * be asked to delay transmission of packets than asking
+			 * our link partner to pause transmission of frames.
+			 */
+#if 0
+			else if(hw->original_fc == e1000_fc_none ||
+				hw->original_fc == e1000_fc_tx_pause) {
+#else
+			else if(hw->fc == e1000_fc_none)
+				DEBUGOUT("Flow Control = NONE.\r\n");
+			else if(hw->fc == e1000_fc_tx_pause) {
+#endif
+				hw->fc = e1000_fc_none;
+				DEBUGOUT("Flow Control = NONE.\r\n");
+			} else {
+				hw->fc = e1000_fc_rx_pause;
+				DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n");
+			}
+			
+			/* Now we need to do one last check...  If we auto-
+			 * negotiated to HALF DUPLEX, flow control should not be
+			 * enabled per IEEE 802.3 spec.
+			 */
+			e1000_get_speed_and_duplex(hw, &speed, &duplex);
+			
+			if(duplex == HALF_DUPLEX)
+				hw->fc = e1000_fc_none;
+			
+			/* Now we call a subroutine to actually force the MAC
+			 * controller to use the correct flow control settings.
+			 */
+			if((ret_val = e1000_force_mac_fc(hw))) {
+				DEBUGOUT("Error forcing flow control settings\n");
+				return ret_val;
+			}
+		} else {
+			DEBUGOUT("Copper PHY and Auto Neg has not completed.\r\n");
+		}
+	}
+	return E1000_SUCCESS;
+}
+
+/******************************************************************************
+ * Checks to see if the link status of the hardware has changed.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *
+ * Called by any function that needs to check the link status of the adapter.
+ *****************************************************************************/
+static int
+e1000_check_for_link(struct e1000_hw *hw)
+{
+	uint32_t rxcw;
+	uint32_t ctrl;
+	uint32_t status;
+	uint32_t rctl;
+	uint32_t signal = 0;
+	int32_t ret_val;
+	uint16_t phy_data;
+	uint16_t lp_capability;
+	
+	DEBUGFUNC("e1000_check_for_link");
+	
+	/* On adapters with a MAC newer than 82544, SW Defineable pin 1 will be 
+	 * set when the optics detect a signal. On older adapters, it will be 
+	 * cleared when there is a signal.  This applies to fiber media only.
+	 */
+	if(hw->media_type == e1000_media_type_fiber)
+		signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0;
+
+	ctrl = E1000_READ_REG(hw, CTRL);
+	status = E1000_READ_REG(hw, STATUS);
+	rxcw = E1000_READ_REG(hw, RXCW);
+	
+	/* If we have a copper PHY then we only want to go out to the PHY
+	 * registers to see if Auto-Neg has completed and/or if our link
+	 * status has changed.  The get_link_status flag will be set if we
+	 * receive a Link Status Change interrupt or we have Rx Sequence
+	 * Errors.
+	 */
+#if 0
+	if((hw->media_type == e1000_media_type_copper) && hw->get_link_status) {
+#else
+	if(hw->media_type == e1000_media_type_copper) {
+#endif
+		/* First we want to see if the MII Status Register reports
+		 * link.  If so, then we want to get the current speed/duplex
+		 * of the PHY.
+		 * Read the register twice since the link bit is sticky.
+		 */
+		if((ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data)))
+			return ret_val;
+		if((ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data)))
+			return ret_val;
+		
+		if(phy_data & MII_SR_LINK_STATUS) {
+#if 0
+			hw->get_link_status = FALSE;
+#endif
+		} else {
+			/* No link detected */
+			return -E1000_ERR_NOLINK;
+		}
+
+		/* We have a M88E1000 PHY and Auto-Neg is enabled.  If we
+		 * have Si on board that is 82544 or newer, Auto
+		 * Speed Detection takes care of MAC speed/duplex
+		 * configuration.  So we only need to configure Collision
+		 * Distance in the MAC.  Otherwise, we need to force
+		 * speed/duplex on the MAC to the current PHY speed/duplex
+		 * settings.
+		 */
+		if(hw->mac_type >= e1000_82544)
+			e1000_config_collision_dist(hw);
+		else {
+			if((ret_val = e1000_config_mac_to_phy(hw))) {
+				DEBUGOUT("Error configuring MAC to PHY settings\n");
+				return ret_val;
+			}
+		}
+		
+		/* Configure Flow Control now that Auto-Neg has completed. First, we 
+		 * need to restore the desired flow control settings because we may
+		 * have had to re-autoneg with a different link partner.
+		 */
+		if((ret_val = e1000_config_fc_after_link_up(hw))) {
+			DEBUGOUT("Error configuring flow control\n");
+			return ret_val;
+		}
+		
+		/* At this point we know that we are on copper and we have
+		 * auto-negotiated link.  These are conditions for checking the link
+		 * parter capability register.  We use the link partner capability to
+		 * determine if TBI Compatibility needs to be turned on or off.  If
+		 * the link partner advertises any speed in addition to Gigabit, then
+		 * we assume that they are GMII-based, and TBI compatibility is not
+		 * needed. If no other speeds are advertised, we assume the link
+		 * partner is TBI-based, and we turn on TBI Compatibility.
+		 */
+		if(hw->tbi_compatibility_en) {
+			if((ret_val = e1000_read_phy_reg(hw, PHY_LP_ABILITY,
+			                                 &lp_capability)))
+				return ret_val;
+			if(lp_capability & (NWAY_LPAR_10T_HD_CAPS |
+                                NWAY_LPAR_10T_FD_CAPS |
+                                NWAY_LPAR_100TX_HD_CAPS |
+                                NWAY_LPAR_100TX_FD_CAPS |
+                                NWAY_LPAR_100T4_CAPS)) {
+				/* If our link partner advertises anything in addition to 
+				 * gigabit, we do not need to enable TBI compatibility.
+				 */
+				if(hw->tbi_compatibility_on) {
+					/* If we previously were in the mode, turn it off. */
+					rctl = E1000_READ_REG(hw, RCTL);
+					rctl &= ~E1000_RCTL_SBP;
+					E1000_WRITE_REG(hw, RCTL, rctl);
+					hw->tbi_compatibility_on = FALSE;
+				}
+			} else {
+				/* If TBI compatibility is was previously off, turn it on. For
+				 * compatibility with a TBI link partner, we will store bad
+				 * packets. Some frames have an additional byte on the end and
+				 * will look like CRC errors to to the hardware.
+				 */
+				if(!hw->tbi_compatibility_on) {
+					hw->tbi_compatibility_on = TRUE;
+					rctl = E1000_READ_REG(hw, RCTL);
+					rctl |= E1000_RCTL_SBP;
+					E1000_WRITE_REG(hw, RCTL, rctl);
+				}
+			}
+		}
+	}
+	/* If we don't have link (auto-negotiation failed or link partner cannot
+	 * auto-negotiate), the cable is plugged in (we have signal), and our
+	 * link partner is not trying to auto-negotiate with us (we are receiving
+	 * idles or data), we need to force link up. We also need to give
+	 * auto-negotiation time to complete, in case the cable was just plugged
+	 * in. The autoneg_failed flag does this.
+	 */
+	else if((((hw->media_type == e1000_media_type_fiber) &&
+	        ((ctrl & E1000_CTRL_SWDPIN1) == signal)) ||
+	        (hw->media_type == e1000_media_type_internal_serdes)) &&
+		(!(status & E1000_STATUS_LU)) &&
+		(!(rxcw & E1000_RXCW_C))) {
+		if(hw->autoneg_failed == 0) {
+			hw->autoneg_failed = 1;
+			return 0;
+		}
+		DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\r\n");
+		
+		/* Disable auto-negotiation in the TXCW register */
+		E1000_WRITE_REG(hw, TXCW, (hw->txcw & ~E1000_TXCW_ANE));
+		
+		/* Force link-up and also force full-duplex. */
+		ctrl = E1000_READ_REG(hw, CTRL);
+		ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
+		E1000_WRITE_REG(hw, CTRL, ctrl);
+		
+		/* Configure Flow Control after forcing link up. */
+		if((ret_val = e1000_config_fc_after_link_up(hw))) {
+			DEBUGOUT("Error configuring flow control\n");
+			return ret_val;
+		}
+	}
+	/* If we are forcing link and we are receiving /C/ ordered sets, re-enable
+	 * auto-negotiation in the TXCW register and disable forced link in the
+	 * Device Control register in an attempt to auto-negotiate with our link
+	 * partner.
+	 */
+	else if(((hw->media_type == e1000_media_type_fiber)  ||
+	         (hw->media_type == e1000_media_type_internal_serdes)) &&
+		(ctrl & E1000_CTRL_SLU) &&
+		(rxcw & E1000_RXCW_C)) {
+		DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\r\n");
+		E1000_WRITE_REG(hw, TXCW, hw->txcw);
+		E1000_WRITE_REG(hw, CTRL, (ctrl & ~E1000_CTRL_SLU));
+	}
+#if 0
+	/* If we force link for non-auto-negotiation switch, check link status
+	 * based on MAC synchronization for internal serdes media type.
+	 */
+	else if((hw->media_type == e1000_media_type_internal_serdes) &&
+			!(E1000_TXCW_ANE & E1000_READ_REG(hw, TXCW))) {
+		/* SYNCH bit and IV bit are sticky. */
+		udelay(10);
+		if(E1000_RXCW_SYNCH & E1000_READ_REG(hw, RXCW)) {
+			if(!(rxcw & E1000_RXCW_IV)) {
+				hw->serdes_link_down = FALSE;
+				DEBUGOUT("SERDES: Link is up.\n");
+			}
+		} else {
+			hw->serdes_link_down = TRUE;
+			DEBUGOUT("SERDES: Link is down.\n");
+		}
+	}
+#endif
+	return E1000_SUCCESS;
+}
+
+/******************************************************************************
+ * Detects the current speed and duplex settings of the hardware.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * speed - Speed of the connection
+ * duplex - Duplex setting of the connection
+ *****************************************************************************/
+static void 
+e1000_get_speed_and_duplex(struct e1000_hw *hw,
+                           uint16_t *speed,
+                           uint16_t *duplex)
+{
+	uint32_t status;
+	
+	DEBUGFUNC("e1000_get_speed_and_duplex");
+	
+	if(hw->mac_type >= e1000_82543) {
+		status = E1000_READ_REG(hw, STATUS);
+		if(status & E1000_STATUS_SPEED_1000) {
+			*speed = SPEED_1000;
+			DEBUGOUT("1000 Mbs, ");
+		} else if(status & E1000_STATUS_SPEED_100) {
+			*speed = SPEED_100;
+			DEBUGOUT("100 Mbs, ");
+		} else {
+			*speed = SPEED_10;
+			DEBUGOUT("10 Mbs, ");
+		}
+		
+		if(status & E1000_STATUS_FD) {
+			*duplex = FULL_DUPLEX;
+			DEBUGOUT("Full Duplex\r\n");
+		} else {
+			*duplex = HALF_DUPLEX;
+			DEBUGOUT(" Half Duplex\r\n");
+		}
+	} else {
+		DEBUGOUT("1000 Mbs, Full Duplex\r\n");
+		*speed = SPEED_1000;
+		*duplex = FULL_DUPLEX;
+	}
+}
+
+/******************************************************************************
+* Blocks until autoneg completes or times out (~4.5 seconds)
+*
+* hw - Struct containing variables accessed by shared code
+******************************************************************************/
+static int
+e1000_wait_autoneg(struct e1000_hw *hw)
+{
+	int32_t ret_val;
+	uint16_t i;
+	uint16_t phy_data;
+	
+	DEBUGFUNC("e1000_wait_autoneg");
+	DEBUGOUT("Waiting for Auto-Neg to complete.\n");
+	
+	/* We will wait for autoneg to complete or 4.5 seconds to expire. */
+	for(i = PHY_AUTO_NEG_TIME; i > 0; i--) {
+		/* Read the MII Status Register and wait for Auto-Neg
+		 * Complete bit to be set.
+		 */
+		if((ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data)))
+			return ret_val;
+		if((ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data)))
+			return ret_val;
+		if(phy_data & MII_SR_AUTONEG_COMPLETE) {
+			DEBUGOUT("Auto-Neg complete.\n");
+			return E1000_SUCCESS;
+		}
+		mdelay(100);
+	}
+	DEBUGOUT("Auto-Neg timedout.\n");
+	return -E1000_ERR_TIMEOUT;
+}
+
+/******************************************************************************
+* Raises the Management Data Clock
+*
+* hw - Struct containing variables accessed by shared code
+* ctrl - Device control register's current value
+******************************************************************************/
+static void
+e1000_raise_mdi_clk(struct e1000_hw *hw,
+                    uint32_t *ctrl)
+{
+	/* Raise the clock input to the Management Data Clock (by setting the MDC
+	 * bit), and then delay 10 microseconds.
+	 */
+	E1000_WRITE_REG(hw, CTRL, (*ctrl | E1000_CTRL_MDC));
+	E1000_WRITE_FLUSH(hw);
+	udelay(10);
+}
+
+/******************************************************************************
+* Lowers the Management Data Clock
+*
+* hw - Struct containing variables accessed by shared code
+* ctrl - Device control register's current value
+******************************************************************************/
+static void
+e1000_lower_mdi_clk(struct e1000_hw *hw,
+                    uint32_t *ctrl)
+{
+	/* Lower the clock input to the Management Data Clock (by clearing the MDC
+	 * bit), and then delay 10 microseconds.
+	 */
+	E1000_WRITE_REG(hw, CTRL, (*ctrl & ~E1000_CTRL_MDC));
+	E1000_WRITE_FLUSH(hw);
+	udelay(10);
+}
+
+/******************************************************************************
+* Shifts data bits out to the PHY
+*
+* hw - Struct containing variables accessed by shared code
+* data - Data to send out to the PHY
+* count - Number of bits to shift out
+*
+* Bits are shifted out in MSB to LSB order.
+******************************************************************************/
+static void
+e1000_shift_out_mdi_bits(struct e1000_hw *hw,
+                         uint32_t data,
+                         uint16_t count)
+{
+	uint32_t ctrl;
+	uint32_t mask;
+
+	/* We need to shift "count" number of bits out to the PHY. So, the value
+	 * in the "data" parameter will be shifted out to the PHY one bit at a 
+	 * time. In order to do this, "data" must be broken down into bits.
+	 */
+	mask = 0x01;
+	mask <<= (count - 1);
+	
+	ctrl = E1000_READ_REG(hw, CTRL);
+	
+	/* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */
+	ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR);
+	
+	while(mask) {
+		/* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and
+		 * then raising and lowering the Management Data Clock. A "0" is
+		 * shifted out to the PHY by setting the MDIO bit to "0" and then
+		 * raising and lowering the clock.
+		 */
+		if(data & mask) ctrl |= E1000_CTRL_MDIO;
+		else ctrl &= ~E1000_CTRL_MDIO;
+		
+		E1000_WRITE_REG(hw, CTRL, ctrl);
+		E1000_WRITE_FLUSH(hw);
+		
+		udelay(10);
+
+		e1000_raise_mdi_clk(hw, &ctrl);
+		e1000_lower_mdi_clk(hw, &ctrl);
+
+		mask = mask >> 1;
+	}
+}
+
+/******************************************************************************
+* Shifts data bits in from the PHY
+*
+* hw - Struct containing variables accessed by shared code
+*
+* Bits are shifted in in MSB to LSB order. 
+******************************************************************************/
+static uint16_t
+e1000_shift_in_mdi_bits(struct e1000_hw *hw)
+{
+	uint32_t ctrl;
+	uint16_t data = 0;
+	uint8_t i;
+
+	/* In order to read a register from the PHY, we need to shift in a total
+	 * of 18 bits from the PHY. The first two bit (turnaround) times are used
+	 * to avoid contention on the MDIO pin when a read operation is performed.
+	 * These two bits are ignored by us and thrown away. Bits are "shifted in"
+	 * by raising the input to the Management Data Clock (setting the MDC bit),
+	 * and then reading the value of the MDIO bit.
+	 */ 
+	ctrl = E1000_READ_REG(hw, CTRL);
+	
+	/* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as input. */
+	ctrl &= ~E1000_CTRL_MDIO_DIR;
+	ctrl &= ~E1000_CTRL_MDIO;
+	
+	E1000_WRITE_REG(hw, CTRL, ctrl);
+	E1000_WRITE_FLUSH(hw);
+	
+	/* Raise and Lower the clock before reading in the data. This accounts for
+	 * the turnaround bits. The first clock occurred when we clocked out the
+	 * last bit of the Register Address.
+	 */
+	e1000_raise_mdi_clk(hw, &ctrl);
+	e1000_lower_mdi_clk(hw, &ctrl);
+	
+	for(data = 0, i = 0; i < 16; i++) {
+		data = data << 1;
+		e1000_raise_mdi_clk(hw, &ctrl);
+		ctrl = E1000_READ_REG(hw, CTRL);
+		/* Check to see if we shifted in a "1". */
+		if(ctrl & E1000_CTRL_MDIO) data |= 1;
+		e1000_lower_mdi_clk(hw, &ctrl);
+	}
+	
+	e1000_raise_mdi_clk(hw, &ctrl);
+	e1000_lower_mdi_clk(hw, &ctrl);
+	
+	return data;
+}
+
+/*****************************************************************************
+* Reads the value from a PHY register, if the value is on a specific non zero
+* page, sets the page first.
+*
+* hw - Struct containing variables accessed by shared code
+* reg_addr - address of the PHY register to read
+******************************************************************************/
+static int
+e1000_read_phy_reg(struct e1000_hw *hw,
+                   uint32_t reg_addr,
+                   uint16_t *phy_data)
+{
+	uint32_t ret_val;
+
+	DEBUGFUNC("e1000_read_phy_reg");
+
+	if(hw->phy_type == e1000_phy_igp &&
+	   (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
+		if((ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
+		                                     (uint16_t)reg_addr)))
+			return ret_val;
+	}
+
+	ret_val = e1000_read_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT & reg_addr,
+	                                phy_data);
+
+	return ret_val;
+}
+
+static int
+e1000_read_phy_reg_ex(struct e1000_hw *hw,
+                      uint32_t reg_addr,
+                      uint16_t *phy_data)
+{
+	uint32_t i;
+	uint32_t mdic = 0;
+	const uint32_t phy_addr = 1;
+
+	DEBUGFUNC("e1000_read_phy_reg_ex");
+	
+	if(reg_addr > MAX_PHY_REG_ADDRESS) {
+		DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
+		return -E1000_ERR_PARAM;
+	}
+	
+	if(hw->mac_type > e1000_82543) {
+		/* Set up Op-code, Phy Address, and register address in the MDI
+		 * Control register.  The MAC will take care of interfacing with the
+		 * PHY to retrieve the desired data.
+		 */
+		mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) |
+			(phy_addr << E1000_MDIC_PHY_SHIFT) | 
+			(E1000_MDIC_OP_READ));
+		
+		E1000_WRITE_REG(hw, MDIC, mdic);
+
+		/* Poll the ready bit to see if the MDI read completed */
+		for(i = 0; i < 64; i++) {
+			udelay(50);
+			mdic = E1000_READ_REG(hw, MDIC);
+			if(mdic & E1000_MDIC_READY) break;
+		}
+		if(!(mdic & E1000_MDIC_READY)) {
+			DEBUGOUT("MDI Read did not complete\n");
+			return -E1000_ERR_PHY;
+		}
+		if(mdic & E1000_MDIC_ERROR) {
+			DEBUGOUT("MDI Error\n");
+			return -E1000_ERR_PHY;
+		}
+		*phy_data = (uint16_t) mdic;
+	} else {
+		/* We must first send a preamble through the MDIO pin to signal the
+		 * beginning of an MII instruction.  This is done by sending 32
+		 * consecutive "1" bits.
+		 */
+		e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);
+		
+		/* Now combine the next few fields that are required for a read
+		 * operation.  We use this method instead of calling the
+		 * e1000_shift_out_mdi_bits routine five different times. The format of
+		 * a MII read instruction consists of a shift out of 14 bits and is
+		 * defined as follows:
+		 *    <Preamble><SOF><Op Code><Phy Addr><Reg Addr>
+		 * followed by a shift in of 18 bits.  This first two bits shifted in
+		 * are TurnAround bits used to avoid contention on the MDIO pin when a
+		 * READ operation is performed.  These two bits are thrown away
+		 * followed by a shift in of 16 bits which contains the desired data.
+		 */
+		mdic = ((reg_addr) | (phy_addr << 5) | 
+			(PHY_OP_READ << 10) | (PHY_SOF << 12));
+		
+		e1000_shift_out_mdi_bits(hw, mdic, 14);
+		
+		/* Now that we've shifted out the read command to the MII, we need to
+		 * "shift in" the 16-bit value (18 total bits) of the requested PHY
+		 * register address.
+		 */
+		*phy_data = e1000_shift_in_mdi_bits(hw);
+	}
+	return E1000_SUCCESS;
+}
+
+/******************************************************************************
+* Writes a value to a PHY register
+*
+* hw - Struct containing variables accessed by shared code
+* reg_addr - address of the PHY register to write
+* data - data to write to the PHY
+******************************************************************************/
+static int 
+e1000_write_phy_reg(struct e1000_hw *hw,
+                    uint32_t reg_addr,
+                    uint16_t phy_data)
+{
+	uint32_t ret_val;
+
+	DEBUGFUNC("e1000_write_phy_reg");
+
+	if(hw->phy_type == e1000_phy_igp &&
+	   (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
+		if((ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
+		                                     (uint16_t)reg_addr)))
+			return ret_val;
+	}
+
+	ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT & reg_addr,
+	                                 phy_data);
+
+	return ret_val;
+}
+
+static int
+e1000_write_phy_reg_ex(struct e1000_hw *hw,
+                       uint32_t reg_addr,
+                       uint16_t phy_data)
+{
+	uint32_t i;
+	uint32_t mdic = 0;
+	const uint32_t phy_addr = 1;
+	
+	DEBUGFUNC("e1000_write_phy_reg_ex");
+	
+	if(reg_addr > MAX_PHY_REG_ADDRESS) {
+		DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
+		return -E1000_ERR_PARAM;
+	}
+	
+	if(hw->mac_type > e1000_82543) {
+		/* Set up Op-code, Phy Address, register address, and data intended
+		 * for the PHY register in the MDI Control register.  The MAC will take
+		 * care of interfacing with the PHY to send the desired data.
+		 */
+		mdic = (((uint32_t) phy_data) |
+			(reg_addr << E1000_MDIC_REG_SHIFT) |
+			(phy_addr << E1000_MDIC_PHY_SHIFT) | 
+			(E1000_MDIC_OP_WRITE));
+		
+		E1000_WRITE_REG(hw, MDIC, mdic);
+		
+		/* Poll the ready bit to see if the MDI read completed */
+		for(i = 0; i < 640; i++) {
+			udelay(5);
+			mdic = E1000_READ_REG(hw, MDIC);
+			if(mdic & E1000_MDIC_READY) break;
+		}
+		if(!(mdic & E1000_MDIC_READY)) {
+			DEBUGOUT("MDI Write did not complete\n");
+			return -E1000_ERR_PHY;
+		}
+	} else {
+		/* We'll need to use the SW defined pins to shift the write command
+		 * out to the PHY. We first send a preamble to the PHY to signal the
+		 * beginning of the MII instruction.  This is done by sending 32 
+		 * consecutive "1" bits.
+		 */
+		e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);
+		
+		/* Now combine the remaining required fields that will indicate a 
+		 * write operation. We use this method instead of calling the
+		 * e1000_shift_out_mdi_bits routine for each field in the command. The
+		 * format of a MII write instruction is as follows:
+		 * <Preamble><SOF><Op Code><Phy Addr><Reg Addr><Turnaround><Data>.
+		 */
+		mdic = ((PHY_TURNAROUND) | (reg_addr << 2) | (phy_addr << 7) |
+			(PHY_OP_WRITE << 12) | (PHY_SOF << 14));
+		mdic <<= 16;
+		mdic |= (uint32_t) phy_data;
+		
+		e1000_shift_out_mdi_bits(hw, mdic, 32);
+	}
+
+	return E1000_SUCCESS;
+}
+
+/******************************************************************************
+* Returns the PHY to the power-on reset state
+*
+* hw - Struct containing variables accessed by shared code
+******************************************************************************/
+static void
+e1000_phy_hw_reset(struct e1000_hw *hw)
+{
+	uint32_t ctrl, ctrl_ext;
+
+	DEBUGFUNC("e1000_phy_hw_reset");
+	
+	DEBUGOUT("Resetting Phy...\n");
+	
+	if(hw->mac_type > e1000_82543) {
+		/* Read the device control register and assert the E1000_CTRL_PHY_RST
+		 * bit. Then, take it out of reset.
+		 */
+		ctrl = E1000_READ_REG(hw, CTRL);
+		E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PHY_RST);
+		E1000_WRITE_FLUSH(hw);
+		mdelay(10);
+		E1000_WRITE_REG(hw, CTRL, ctrl);
+		E1000_WRITE_FLUSH(hw);
+	} else {
+		/* Read the Extended Device Control Register, assert the PHY_RESET_DIR
+		 * bit to put the PHY into reset. Then, take it out of reset.
+		 */
+		ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
+		ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR;
+		ctrl_ext &= ~E1000_CTRL_EXT_SDP4_DATA;
+		E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
+		E1000_WRITE_FLUSH(hw);
+		mdelay(10);
+		ctrl_ext |= E1000_CTRL_EXT_SDP4_DATA;
+		E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
+		E1000_WRITE_FLUSH(hw);
+	}
+	udelay(150);
+}
+
+/******************************************************************************
+* Resets the PHY
+*
+* hw - Struct containing variables accessed by shared code
+*
+* Sets bit 15 of the MII Control regiser
+******************************************************************************/
+static int 
+e1000_phy_reset(struct e1000_hw *hw)
+{
+	int32_t ret_val;
+	uint16_t phy_data;
+
+	DEBUGFUNC("e1000_phy_reset");
+
+	if(hw->mac_type != e1000_82541_rev_2) {
+		if((ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data)))
+			return ret_val;
+		
+		phy_data |= MII_CR_RESET;
+		if((ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data)))
+			return ret_val;
+		
+		udelay(1);
+	} else e1000_phy_hw_reset(hw);
+
+	if(hw->phy_type == e1000_phy_igp)
+		e1000_phy_init_script(hw);
+
+	return E1000_SUCCESS;
+}
+
+/******************************************************************************
+* Probes the expected PHY address for known PHY IDs
+*
+* hw - Struct containing variables accessed by shared code
+******************************************************************************/
+static int
+e1000_detect_gig_phy(struct e1000_hw *hw)
+{
+	int32_t phy_init_status, ret_val;
+	uint16_t phy_id_high, phy_id_low;
+	boolean_t match = FALSE;
+
+	DEBUGFUNC("e1000_detect_gig_phy");
+	
+	/* Read the PHY ID Registers to identify which PHY is onboard. */
+	if((ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high)))
+		return ret_val;
+
+	hw->phy_id = (uint32_t) (phy_id_high << 16);
+	udelay(20);
+	if((ret_val = e1000_read_phy_reg(hw, PHY_ID2, &phy_id_low)))
+		return ret_val;
+	
+	hw->phy_id |= (uint32_t) (phy_id_low & PHY_REVISION_MASK);
+#ifdef LINUX_DRIVER
+	hw->phy_revision = (uint32_t) phy_id_low & ~PHY_REVISION_MASK;
+#endif
+	
+	switch(hw->mac_type) {
+	case e1000_82543:
+		if(hw->phy_id == M88E1000_E_PHY_ID) match = TRUE;
+		break;
+	case e1000_82544:
+		if(hw->phy_id == M88E1000_I_PHY_ID) match = TRUE;
+		break;
+	case e1000_82540:
+	case e1000_82545:
+	case e1000_82545_rev_3:
+	case e1000_82546:
+	case e1000_82546_rev_3:
+		if(hw->phy_id == M88E1011_I_PHY_ID) match = TRUE;
+		break;
+	case e1000_82541:
+	case e1000_82541_rev_2:
+	case e1000_82547:
+	case e1000_82547_rev_2:
+		if(hw->phy_id == IGP01E1000_I_PHY_ID) match = TRUE;
+		break;
+	default:
+		DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type);
+		return -E1000_ERR_CONFIG;
+	}
+	phy_init_status = e1000_set_phy_type(hw);
+
+	if ((match) && (phy_init_status == E1000_SUCCESS)) {
+		DEBUGOUT1("PHY ID 0x%X detected\n", hw->phy_id);
+		return E1000_SUCCESS;
+	}
+	DEBUGOUT1("Invalid PHY ID 0x%X\n", hw->phy_id);
+	return -E1000_ERR_PHY;
+}
+
+/******************************************************************************
+ * Sets up eeprom variables in the hw struct.  Must be called after mac_type
+ * is configured.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+static void
+e1000_init_eeprom_params(struct e1000_hw *hw)
+{
+	struct e1000_eeprom_info *eeprom = &hw->eeprom;
+	uint32_t eecd = E1000_READ_REG(hw, EECD);
+	uint16_t eeprom_size;
+
+	DEBUGFUNC("e1000_init_eeprom_params");
+
+	switch (hw->mac_type) {
+	case e1000_82542_rev2_0:
+	case e1000_82542_rev2_1:
+	case e1000_82543:
+	case e1000_82544:
+		eeprom->type = e1000_eeprom_microwire;
+		eeprom->word_size = 64;
+		eeprom->opcode_bits = 3;
+		eeprom->address_bits = 6;
+		eeprom->delay_usec = 50;
+		break;
+	case e1000_82540:
+	case e1000_82545:
+	case e1000_82545_rev_3:
+	case e1000_82546:
+	case e1000_82546_rev_3:
+		eeprom->type = e1000_eeprom_microwire;
+		eeprom->opcode_bits = 3;
+		eeprom->delay_usec = 50;
+		if(eecd & E1000_EECD_SIZE) {
+			eeprom->word_size = 256;
+			eeprom->address_bits = 8;
+		} else {
+			eeprom->word_size = 64;
+			eeprom->address_bits = 6;
+		}
+		break;
+	case e1000_82541:
+	case e1000_82541_rev_2:
+	case e1000_82547:
+	case e1000_82547_rev_2:
+		if (eecd & E1000_EECD_TYPE) {
+			eeprom->type = e1000_eeprom_spi;
+			if (eecd & E1000_EECD_ADDR_BITS) {
+				eeprom->page_size = 32;
+				eeprom->address_bits = 16;
+			} else {
+				eeprom->page_size = 8;
+				eeprom->address_bits = 8;
+			}
+		} else {
+			eeprom->type = e1000_eeprom_microwire;
+			eeprom->opcode_bits = 3;
+			eeprom->delay_usec = 50;
+			if (eecd & E1000_EECD_ADDR_BITS) {
+				eeprom->word_size = 256;
+				eeprom->address_bits = 8;
+			} else {
+				eeprom->word_size = 64;
+				eeprom->address_bits = 6;
+			}
+		}
+		break;
+	default:
+		eeprom->type = e1000_eeprom_spi;
+		if (eecd & E1000_EECD_ADDR_BITS) {
+			eeprom->page_size = 32;
+			eeprom->address_bits = 16;
+		} else {
+			eeprom->page_size = 8;
+			eeprom->address_bits = 8;
+		}
+		break;
+	}
+
+	if (eeprom->type == e1000_eeprom_spi) {
+		eeprom->opcode_bits = 8;
+		eeprom->delay_usec = 1;
+		eeprom->word_size = 64;
+		if (e1000_read_eeprom(hw, EEPROM_CFG, 1, &eeprom_size) == 0) {
+			eeprom_size &= EEPROM_SIZE_MASK;
+
+			switch (eeprom_size) {
+			case EEPROM_SIZE_16KB:
+				eeprom->word_size = 8192;
+				break;
+			case EEPROM_SIZE_8KB:
+				eeprom->word_size = 4096;
+				break;
+			case EEPROM_SIZE_4KB:
+				eeprom->word_size = 2048;
+				break;
+			case EEPROM_SIZE_2KB:
+				eeprom->word_size = 1024;
+				break;
+			case EEPROM_SIZE_1KB:
+				eeprom->word_size = 512;
+				break;
+			case EEPROM_SIZE_512B:
+				eeprom->word_size = 256;
+				break;
+			case EEPROM_SIZE_128B:
+			default:
+				break;
+			}
+		}
+	}
+}
+
+/**
+ * e1000_reset - Reset the adapter
+ */
+
+static int
+e1000_reset(struct e1000_hw *hw)
+{
+	uint32_t pba;
+	/* Repartition Pba for greater than 9k mtu
+	 * To take effect CTRL.RST is required.
+	 */
+
+	if(hw->mac_type < e1000_82547) {
+		pba = E1000_PBA_48K;
+	} else {
+		pba = E1000_PBA_30K;
+	}
+	E1000_WRITE_REG(hw, PBA, pba);
+
+	/* flow control settings */
+#if 0
+	hw->fc_high_water = FC_DEFAULT_HI_THRESH;
+	hw->fc_low_water = FC_DEFAULT_LO_THRESH;
+	hw->fc_pause_time = FC_DEFAULT_TX_TIMER;
+	hw->fc_send_xon = 1;
+	hw->fc = hw->original_fc;
+#endif
+	
+	e1000_reset_hw(hw);
+	if(hw->mac_type >= e1000_82544)
+		E1000_WRITE_REG(hw, WUC, 0);
+	return e1000_init_hw(hw);
+}
+
+/**
+ * e1000_sw_init - Initialize general software structures (struct e1000_adapter)
+ * @adapter: board private structure to initialize
+ *
+ * e1000_sw_init initializes the Adapter private data structure.
+ * Fields are initialized based on PCI device information and
+ * OS network device settings (MTU size).
+ **/
+
+static int 
+e1000_sw_init(struct pci_device *pdev, struct e1000_hw *hw)
+{
+	int result;
+
+	/* PCI config space info */
+	pci_read_config_word(pdev, PCI_VENDOR_ID, &hw->vendor_id);
+	pci_read_config_word(pdev, PCI_DEVICE_ID, &hw->device_id);
+	pci_read_config_byte(pdev, PCI_REVISION, &hw->revision_id);
+#if 0
+	pci_read_config_word(pdev, PCI_SUBSYSTEM_VENDOR_ID,
+                             &hw->subsystem_vendor_id);
+	pci_read_config_word(pdev, PCI_SUBSYSTEM_ID, &hw->subsystem_id);
+#endif
+
+	pci_read_config_word(pdev, PCI_COMMAND, &hw->pci_cmd_word);
+
+	/* identify the MAC */
+
+	result = e1000_set_mac_type(hw);
+	if (result) {
+		E1000_ERR("Unknown MAC Type\n");
+		return result;
+	}
+
+	/* initialize eeprom parameters */
+
+	e1000_init_eeprom_params(hw);
+
+#if 0
+	if((hw->mac_type == e1000_82541) ||
+	   (hw->mac_type == e1000_82547) ||
+	   (hw->mac_type == e1000_82541_rev_2) ||
+	   (hw->mac_type == e1000_82547_rev_2))
+		hw->phy_init_script = 1;
+#endif
+
+	e1000_set_media_type(hw);
+
+#if 0
+	if(hw->mac_type < e1000_82543)
+		hw->report_tx_early = 0;
+	else
+		hw->report_tx_early = 1;
+
+	hw->wait_autoneg_complete = FALSE;
+#endif
+	hw->tbi_compatibility_en = TRUE;
+#if 0
+	hw->adaptive_ifs = TRUE;
+
+	/* Copper options */
+
+	if(hw->media_type == e1000_media_type_copper) {
+		hw->mdix = AUTO_ALL_MODES;
+		hw->disable_polarity_correction = FALSE;
+		hw->master_slave = E1000_MASTER_SLAVE;
+	}
+#endif
+	return E1000_SUCCESS;
+}
+
+static void fill_rx (void)
+{
+	struct e1000_rx_desc *rd;
+	rx_last = rx_tail;
+	rd = rx_base + rx_tail;
+	rx_tail = (rx_tail + 1) % 8;
+	memset (rd, 0, 16);
+	rd->buffer_addr = virt_to_bus(&packet);
+	E1000_WRITE_REG (&hw, RDT, rx_tail);
+}
+
+static void init_descriptor (void)
+{
+	unsigned long ptr;
+	unsigned long tctl;
+
+	ptr = virt_to_phys(tx_pool);
+	if (ptr & 0xf)
+		ptr = (ptr + 0x10) & (~0xf);
+
+	tx_base = phys_to_virt(ptr);
+
+	E1000_WRITE_REG (&hw, TDBAL, virt_to_bus(tx_base));
+	E1000_WRITE_REG (&hw, TDBAH, 0);
+	E1000_WRITE_REG (&hw, TDLEN, 128);
+
+	/* Setup the HW Tx Head and Tail descriptor pointers */
+
+	E1000_WRITE_REG (&hw, TDH, 0);
+	E1000_WRITE_REG (&hw, TDT, 0);
+	tx_tail = 0;
+
+	/* Program the Transmit Control Register */
+
+#ifdef LINUX_DRIVER_TCTL
+	tctl = E1000_READ_REG(&hw, TCTL);
+
+	tctl &= ~E1000_TCTL_CT;
+	tctl |= E1000_TCTL_EN | E1000_TCTL_PSP |
+		(E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT);
+#else
+	tctl = E1000_TCTL_PSP | E1000_TCTL_EN |
+		(E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT) | 
+		(E1000_HDX_COLLISION_DISTANCE << E1000_COLD_SHIFT);
+#endif
+
+	E1000_WRITE_REG (&hw, TCTL, tctl);
+
+	e1000_config_collision_dist(&hw);
+
+
+	rx_tail = 0;
+	/* disable receive */
+	E1000_WRITE_REG (&hw, RCTL, 0);
+	ptr = virt_to_phys(rx_pool);
+	if (ptr & 0xf)
+		ptr = (ptr + 0x10) & (~0xf);
+	rx_base = phys_to_virt(ptr);
+
+	/* Setup the Base and Length of the Rx Descriptor Ring */
+
+	E1000_WRITE_REG (&hw, RDBAL, virt_to_bus(rx_base));
+	E1000_WRITE_REG (&hw, RDBAH, 0);
+
+	E1000_WRITE_REG (&hw, RDLEN, 128);
+
+	/* Setup the HW Rx Head and Tail Descriptor Pointers */
+	E1000_WRITE_REG (&hw, RDH, 0);
+	E1000_WRITE_REG (&hw, RDT, 0);
+
+	E1000_WRITE_REG (&hw, RCTL, 
+		E1000_RCTL_EN | 
+		E1000_RCTL_BAM | 
+		E1000_RCTL_SZ_2048 | 
+		E1000_RCTL_MPE);
+	fill_rx();
+}
+
+
+
+/**************************************************************************
+POLL - Wait for a frame
+***************************************************************************/
+static int
+e1000_poll (struct nic *nic, int retrieve)
+{
+	/* return true if there's an ethernet packet ready to read */
+	/* nic->packet should contain data on return */
+	/* nic->packetlen should contain length of data */
+	struct e1000_rx_desc *rd;
+	uint32_t icr;
+
+	rd = rx_base + rx_last;
+	if (!rd->status & E1000_RXD_STAT_DD)
+		return 0;
+
+	if ( ! retrieve ) return 1;
+
+	//      printf("recv: packet %! -> %! len=%d \n", packet+6, packet,rd->Length);
+	memcpy (nic->packet, packet, rd->length);
+	nic->packetlen = rd->length;
+	fill_rx ();
+
+	/* Acknowledge interrupt. */
+	icr = E1000_READ_REG(&hw, ICR);
+
+	return 1;
+}
+
+/**************************************************************************
+TRANSMIT - Transmit a frame
+***************************************************************************/
+static void
+e1000_transmit (struct nic *nic, const char *d,	/* Destination */
+		    unsigned int type,	/* Type */
+		    unsigned int size,	/* size */
+		    const char *p)	/* Packet */
+{
+	/* send the packet to destination */
+	struct eth_hdr {
+		unsigned char dst_addr[ETH_ALEN];
+		unsigned char src_addr[ETH_ALEN];
+		unsigned short type;
+	} hdr;
+	struct e1000_tx_desc *txhd;	/* header */
+	struct e1000_tx_desc *txp;	/* payload */
+	DEBUGFUNC("send");
+
+	memcpy (&hdr.dst_addr, d, ETH_ALEN);
+	memcpy (&hdr.src_addr, nic->node_addr, ETH_ALEN);
+
+	hdr.type = htons (type);
+	txhd = tx_base + tx_tail;
+	tx_tail = (tx_tail + 1) % 8;
+	txp = tx_base + tx_tail;
+	tx_tail = (tx_tail + 1) % 8;
+
+	txhd->buffer_addr = virt_to_bus (&hdr);
+	txhd->lower.data = sizeof (hdr);
+	txhd->upper.data = 0;
+
+	txp->buffer_addr = virt_to_bus(p);
+	txp->lower.data = E1000_TXD_CMD_RPS | E1000_TXD_CMD_EOP | E1000_TXD_CMD_IFCS | size;
+	txp->upper.data = 0;
+
+	E1000_WRITE_REG (&hw, TDT, tx_tail);
+	while (!(txp->upper.data & E1000_TXD_STAT_DD)) {
+		udelay(10);	/* give the nic a chance to write to the register */
+		poll_interruptions();
+	}
+	DEBUGFUNC("send end");
+}
+
+
+/**************************************************************************
+DISABLE - Turn off ethernet interface
+***************************************************************************/
+static void e1000_disable (struct dev *dev __unused)
+{
+	/* Clear the transmit ring */
+	E1000_WRITE_REG (&hw, TDH, 0);
+	E1000_WRITE_REG (&hw, TDT, 0);
+
+	/* Clear the receive ring */
+	E1000_WRITE_REG (&hw, RDH, 0);
+	E1000_WRITE_REG (&hw, RDT, 0);
+
+	/* put the card in its initial state */
+	switch(hw.mac_type) {
+		case e1000_82544:
+		case e1000_82540:
+		case e1000_82545:
+		case e1000_82546:
+		case e1000_82541:
+		case e1000_82541_rev_2:
+			/* These controllers can't ack the 64-bit write when issuing the
+			 * reset, so use IO-mapping as a workaround to issue the reset */
+			E1000_WRITE_REG_IO(&hw, CTRL, E1000_CTRL_RST);
+			break;
+		case e1000_82545_rev_3:
+		case e1000_82546_rev_3:
+			/* Reset is performed on a shadow of the control register */
+			E1000_WRITE_REG(&hw, CTRL_DUP, E1000_CTRL_RST);
+			break;
+		default:
+			E1000_WRITE_REG(&hw, CTRL, E1000_CTRL_RST);
+			break;
+	}
+
+	/* Turn off the ethernet interface */
+	E1000_WRITE_REG (&hw, RCTL, 0);
+	E1000_WRITE_REG (&hw, TCTL, 0);
+	mdelay (10);
+
+	/* Unmap my window to the device */
+	iounmap(hw.hw_addr);
+}
+
+/**************************************************************************
+IRQ - Enable, Disable, or Force interrupts
+***************************************************************************/
+static void e1000_irq(struct nic *nic __unused, irq_action_t action)
+{
+	switch ( action ) {
+	case DISABLE :
+		E1000_WRITE_REG(&hw, IMC, ~0);
+		E1000_WRITE_FLUSH(&hw);
+		break;
+	case ENABLE :
+		E1000_WRITE_REG(&hw, IMS,
+				E1000_IMS_RXT0 | E1000_IMS_RXSEQ);
+		E1000_WRITE_FLUSH(&hw);
+		break;
+	case FORCE :
+		E1000_WRITE_REG(&hw, ICS, E1000_ICS_RXT0);
+		break;
+	}
+}
+
+#define IORESOURCE_IO	0x00000100     /* Resource type */
+#define BAR_0		0
+#define BAR_1		1
+#define BAR_5		5
+
+/**************************************************************************
+PROBE - Look for an adapter, this routine's visible to the outside
+You should omit the last argument struct pci_device * for a non-PCI NIC
+***************************************************************************/
+static int e1000_probe(struct dev *dev, struct pci_device *p)
+{
+	struct nic *nic = (struct nic *)dev;
+	unsigned long mmio_start, mmio_len;
+	int ret_val, i;
+
+	if (p == 0)
+		return 0;
+	/* Initialize hw with default values */
+	memset(&hw, 0, sizeof(hw));
+	hw.pdev = p;
+
+#if 1
+	/* Are these variables needed? */
+	hw.fc                    = e1000_fc_none;
+#if 0
+	hw.original_fc           = e1000_fc_none;
+#endif
+	hw.autoneg_failed        = 0;
+#if 0
+	hw.get_link_status       = TRUE;
+#endif
+#endif
+
+	mmio_start = pci_bar_start(p, PCI_BASE_ADDRESS_0);
+	mmio_len   = pci_bar_size(p,  PCI_BASE_ADDRESS_0);
+	hw.hw_addr = ioremap(mmio_start, mmio_len);
+
+	for(i = BAR_1; i <= BAR_5; i++) {
+		if(pci_bar_size(p, i) == 0)
+			continue;                
+		if(pci_find_capability(p, i) & IORESOURCE_IO) {
+			hw.io_base = pci_bar_start(p, i);
+			break;
+                }        
+	}
+
+	adjust_pci_device(p);
+
+	nic->ioaddr   = p->ioaddr & ~3;
+	nic->irqno    = p->irq;
+
+	/* From Matt Hortman <mbhortman@acpthinclient.com> */
+	/* MAC and Phy settings */
+
+	/* setup the private structure */
+	if (e1000_sw_init(p, &hw) < 0) {
+		iounmap(hw.hw_addr);
+		return 0;
+	}
+
+	/* make sure the EEPROM is good */
+
+	if (e1000_validate_eeprom_checksum(&hw) < 0) {
+		printf ("The EEPROM Checksum Is Not Valid\n");
+		iounmap(hw.hw_addr);
+		return 0;
+	}
+
+	/* copy the MAC address out of the EEPROM */
+
+	e1000_read_mac_addr(&hw);
+	memcpy (nic->node_addr, hw.mac_addr, ETH_ALEN);
+	
+	printf("Ethernet addr: %!\n", nic->node_addr);
+
+	/* reset the hardware with the new settings */
+
+	ret_val = e1000_reset(&hw);
+	if (ret_val < 0) {
+		if ((ret_val == -E1000_ERR_NOLINK) ||
+			(ret_val == -E1000_ERR_TIMEOUT)) {
+			E1000_ERR("Valid Link not detected\n");
+		} else {
+			E1000_ERR("Hardware Initialization Failed\n");
+		}
+		iounmap(hw.hw_addr);
+		return 0;
+	}
+	init_descriptor();
+
+	/* point to NIC specific routines */
+	dev->disable  = e1000_disable;
+	nic->poll     = e1000_poll;
+	nic->transmit = e1000_transmit;
+	nic->irq      = e1000_irq;
+
+	return 1;
+}
+
+static struct pci_id e1000_nics[] = {
+PCI_ROM(0x8086, 0x1000, "e1000-82542",               "Intel EtherExpressPro1000"),
+PCI_ROM(0x8086, 0x1001, "e1000-82543gc-fiber",       "Intel EtherExpressPro1000 82543GC Fiber"),
+PCI_ROM(0x8086, 0x1004, "e1000-82543gc-copper",	     "Intel EtherExpressPro1000 82543GC Copper"),
+PCI_ROM(0x8086, 0x1008, "e1000-82544ei-copper",      "Intel EtherExpressPro1000 82544EI Copper"),
+PCI_ROM(0x8086, 0x1009, "e1000-82544ei-fiber",       "Intel EtherExpressPro1000 82544EI Fiber"),
+PCI_ROM(0x8086, 0x100C, "e1000-82544gc-copper",      "Intel EtherExpressPro1000 82544GC Copper"),
+PCI_ROM(0x8086, 0x100D, "e1000-82544gc-lom",         "Intel EtherExpressPro1000 82544GC LOM"),
+PCI_ROM(0x8086, 0x100E, "e1000-82540em",     	     "Intel EtherExpressPro1000 82540EM"),
+PCI_ROM(0x8086, 0x100F, "e1000-82545em-copper",      "Intel EtherExpressPro1000 82545EM Copper"),
+PCI_ROM(0x8086, 0x1010, "e1000-82546eb-copper",      "Intel EtherExpressPro1000 82546EB Copper"),
+PCI_ROM(0x8086, 0x1011, "e1000-82545em-fiber",       "Intel EtherExpressPro1000 82545EM Fiber"),
+PCI_ROM(0x8086, 0x1012, "e1000-82546eb-fiber", 	     "Intel EtherExpressPro1000 82546EB Copper"),
+PCI_ROM(0x8086, 0x1013, "e1000-82541ei",	     "Intel EtherExpressPro1000 82541EI"),
+PCI_ROM(0x8086, 0x1015, "e1000-82540em-lom",  	     "Intel EtherExpressPro1000 82540EM LOM"),
+PCI_ROM(0x8086, 0x1016, "e1000-82540ep-lom",	     "Intel EtherExpressPro1000 82540EP LOM"),
+PCI_ROM(0x8086, 0x1017, "e1000-82540ep",	     "Intel EtherExpressPro1000 82540EP"),
+PCI_ROM(0x8086, 0x1018, "e1000-82541ep",	     "Intel EtherExpressPro1000 82541EP"),
+PCI_ROM(0x8086, 0x1019, "e1000-82547ei",	     "Intel EtherExpressPro1000 82547EI"),
+PCI_ROM(0x8086, 0x101d, "e1000-82546eb-quad-copper", "Intel EtherExpressPro1000 82546EB Quad Copper"),
+PCI_ROM(0x8086, 0x101e, "e1000-82540ep-lp",	     "Intel EtherExpressPro1000 82540EP LP"),
+PCI_ROM(0x8086, 0x1026, "e1000-82545gm-copper",	     "Intel EtherExpressPro1000 82545GM Copper"),
+PCI_ROM(0x8086, 0x1027, "e1000-82545gm-fiber",	     "Intel EtherExpressPro1000 82545GM Fiber"),
+PCI_ROM(0x8086, 0x1028, "e1000-82545gm-serdes",	     "Intel EtherExpressPro1000 82545GM SERDES"),
+PCI_ROM(0x8086, 0x1075, "e1000-82547gi",	     "Intel EtherExpressPro1000 82547GI"),
+PCI_ROM(0x8086, 0x1076, "e1000-82541gi",	     "Intel EtherExpressPro1000 82541GI"),
+PCI_ROM(0x8086, 0x1077, "e1000-82541gi-mobile",	     "Intel EtherExpressPro1000 82541GI Mobile"),
+PCI_ROM(0x8086, 0x1078, "e1000-82541er",	     "Intel EtherExpressPro1000 82541ER"),
+PCI_ROM(0x8086, 0x1079, "e1000-82546gb-copper",	     "Intel EtherExpressPro1000 82546GB Copper"),
+PCI_ROM(0x8086, 0x107a, "e1000-82546gb-fiber",	     "Intel EtherExpressPro1000 82546GB Fiber"),
+PCI_ROM(0x8086, 0x107b, "e1000-82546gb-serdes",	     "Intel EtherExpressPro1000 82546GB SERDES"),
+};
+
+static struct pci_driver e1000_driver __pci_driver = {
+	.type     = NIC_DRIVER,
+	.name     = "E1000",
+	.probe    = e1000_probe,
+	.ids      = e1000_nics,
+	.id_count = sizeof(e1000_nics)/sizeof(e1000_nics[0]),
+	.class    = 0,
+};