[ethernet] Update mii.h and use it in drivers that had a private copy

Signed-off-by: Michael Brown <mcb30@etherboot.org>

1 files changed, 0 insertions, 107 deletions

diff --git a/src/drivers/net/tg3.h b/src/drivers/net/tg3.h
index a7762c3c..deeb0add 100644
--- a/src/drivers/net/tg3.h
+++ b/src/drivers/net/tg3.h
@@ -77,100 +77,6 @@ typedef unsigned long dma_addr_t;
 #define WAKE_MAGIC		(1 << 5)
 #define WAKE_MAGICSECURE	(1 << 6) /* only meaningful if WAKE_MAGIC */
 
-/* Generic MII registers. */
-
-#define MII_BMCR            0x00        /* Basic mode control register */
-#define MII_BMSR            0x01        /* Basic mode status register  */
-#define MII_PHYSID1         0x02        /* PHYS ID 1                   */
-#define MII_PHYSID2         0x03        /* PHYS ID 2                   */
-#define MII_ADVERTISE       0x04        /* Advertisement control reg   */
-#define MII_LPA             0x05        /* Link partner ability reg    */
-#define MII_EXPANSION       0x06        /* Expansion register          */
-#define MII_DCOUNTER        0x12        /* Disconnect counter          */
-#define MII_FCSCOUNTER      0x13        /* False carrier counter       */
-#define MII_NWAYTEST        0x14        /* N-way auto-neg test reg     */
-#define MII_RERRCOUNTER     0x15        /* Receive error counter       */
-#define MII_SREVISION       0x16        /* Silicon revision            */
-#define MII_RESV1           0x17        /* Reserved...                 */
-#define MII_LBRERROR        0x18        /* Lpback, rx, bypass error    */
-#define MII_PHYADDR         0x19        /* PHY address                 */
-#define MII_RESV2           0x1a        /* Reserved...                 */
-#define MII_TPISTATUS       0x1b        /* TPI status for 10mbps       */
-#define MII_NCONFIG         0x1c        /* Network interface config    */
-
-/* Basic mode control register. */
-#define BMCR_RESV               0x007f  /* Unused...                   */
-#define BMCR_CTST               0x0080  /* Collision test              */
-#define BMCR_FULLDPLX           0x0100  /* Full duplex                 */
-#define BMCR_ANRESTART          0x0200  /* Auto negotiation restart    */
-#define BMCR_ISOLATE            0x0400  /* Disconnect DP83840 from MII */
-#define BMCR_PDOWN              0x0800  /* Powerdown the DP83840       */
-#define BMCR_ANENABLE           0x1000  /* Enable auto negotiation     */
-#define BMCR_SPEED100           0x2000  /* Select 100Mbps              */
-#define BMCR_LOOPBACK           0x4000  /* TXD loopback bits           */
-#define BMCR_RESET              0x8000  /* Reset the DP83840           */
-
-/* Basic mode status register. */
-#define BMSR_ERCAP              0x0001  /* Ext-reg capability          */
-#define BMSR_JCD                0x0002  /* Jabber detected             */
-#define BMSR_LSTATUS            0x0004  /* Link status                 */
-#define BMSR_ANEGCAPABLE        0x0008  /* Able to do auto-negotiation */
-#define BMSR_RFAULT             0x0010  /* Remote fault detected       */
-#define BMSR_ANEGCOMPLETE       0x0020  /* Auto-negotiation complete   */
-#define BMSR_RESV               0x07c0  /* Unused...                   */
-#define BMSR_10HALF             0x0800  /* Can do 10mbps, half-duplex  */
-#define BMSR_10FULL             0x1000  /* Can do 10mbps, full-duplex  */
-#define BMSR_100HALF            0x2000  /* Can do 100mbps, half-duplex */
-#define BMSR_100FULL            0x4000  /* Can do 100mbps, full-duplex */
-#define BMSR_100BASE4           0x8000  /* Can do 100mbps, 4k packets  */
-
-/* Advertisement control register. */
-#define ADVERTISE_SLCT          0x001f  /* Selector bits               */
-#define ADVERTISE_CSMA          0x0001  /* Only selector supported     */
-#define ADVERTISE_10HALF        0x0020  /* Try for 10mbps half-duplex  */
-#define ADVERTISE_10FULL        0x0040  /* Try for 10mbps full-duplex  */
-#define ADVERTISE_100HALF       0x0080  /* Try for 100mbps half-duplex */
-#define ADVERTISE_100FULL       0x0100  /* Try for 100mbps full-duplex */
-#define ADVERTISE_100BASE4      0x0200  /* Try for 100mbps 4k packets  */
-#define ADVERTISE_RESV          0x1c00  /* Unused...                   */
-#define ADVERTISE_RFAULT        0x2000  /* Say we can detect faults    */
-#define ADVERTISE_LPACK         0x4000  /* Ack link partners response  */
-#define ADVERTISE_NPAGE         0x8000  /* Next page bit               */
-
-#define ADVERTISE_FULL (ADVERTISE_100FULL | ADVERTISE_10FULL | \
-			ADVERTISE_CSMA)
-#define ADVERTISE_ALL (ADVERTISE_10HALF | ADVERTISE_10FULL | \
-                       ADVERTISE_100HALF | ADVERTISE_100FULL)
-
-/* Link partner ability register. */
-#define LPA_SLCT                0x001f  /* Same as advertise selector  */
-#define LPA_10HALF              0x0020  /* Can do 10mbps half-duplex   */
-#define LPA_10FULL              0x0040  /* Can do 10mbps full-duplex   */
-#define LPA_100HALF             0x0080  /* Can do 100mbps half-duplex  */
-#define LPA_100FULL             0x0100  /* Can do 100mbps full-duplex  */
-#define LPA_100BASE4            0x0200  /* Can do 100mbps 4k packets   */
-#define LPA_RESV                0x1c00  /* Unused...                   */
-#define LPA_RFAULT              0x2000  /* Link partner faulted        */
-#define LPA_LPACK               0x4000  /* Link partner acked us       */
-#define LPA_NPAGE               0x8000  /* Next page bit               */
-
-#define LPA_DUPLEX		(LPA_10FULL | LPA_100FULL)
-#define LPA_100			(LPA_100FULL | LPA_100HALF | LPA_100BASE4)
-
-/* Expansion register for auto-negotiation. */
-#define EXPANSION_NWAY          0x0001  /* Can do N-way auto-nego      */
-#define EXPANSION_LCWP          0x0002  /* Got new RX page code word   */
-#define EXPANSION_ENABLENPAGE   0x0004  /* This enables npage words    */
-#define EXPANSION_NPCAPABLE     0x0008  /* Link partner supports npage */
-#define EXPANSION_MFAULTS       0x0010  /* Multiple faults detected    */
-#define EXPANSION_RESV          0xffe0  /* Unused...                   */
-
-/* N-way test register. */
-#define NWAYTEST_RESV1          0x00ff  /* Unused...                   */
-#define NWAYTEST_LOOPBACK       0x0100  /* Enable loopback for N-way   */
-#define NWAYTEST_RESV2          0xfe00  /* Unused...                   */
-
-
 /* From tg3.h */
 
 #define TG3_64BIT_REG_HIGH		0x00UL
@@ -1634,19 +1540,6 @@ typedef unsigned long dma_addr_t;
 #define MII_TG3_INT_DUPLEXCHG		0x0008
 #define MII_TG3_INT_ANEG_PAGE_RX	0x0400
 
-/* XXX Add this to mii.h */
-#ifndef ADVERTISE_PAUSE
-#define ADVERTISE_PAUSE_CAP		0x0400
-#endif
-#ifndef ADVERTISE_PAUSE_ASYM
-#define ADVERTISE_PAUSE_ASYM		0x0800
-#endif
-#ifndef LPA_PAUSE
-#define LPA_PAUSE_CAP			0x0400
-#endif
-#ifndef LPA_PAUSE_ASYM
-#define LPA_PAUSE_ASYM			0x0800
-#endif
 
 /* There are two ways to manage the TX descriptors on the tigon3.
  * Either the descriptors are in host DMA'able memory, or they