diff options
Diffstat (limited to 'src/drivers/net/mtd80x.c')
| -rw-r--r-- | src/drivers/net/mtd80x.c | 66 |
1 files changed, 1 insertions, 65 deletions
diff --git a/src/drivers/net/mtd80x.c b/src/drivers/net/mtd80x.c index d0e1554f..7cf59b0e 100644 --- a/src/drivers/net/mtd80x.c +++ b/src/drivers/net/mtd80x.c @@ -32,6 +32,7 @@ FILE_LICENCE ( GPL2_OR_LATER ); /* to get the PCI support functions, if this is a PCI NIC */ #include <gpxe/pci.h> #include <gpxe/ethernet.h> +#include <mii.h> /* Condensed operations for readability. */ #define virt_to_le32desc(addr) cpu_to_le32(virt_to_bus(addr)) @@ -61,71 +62,6 @@ FILE_LICENCE ( GPL2_OR_LATER ); */ #define PKT_BUF_SZ 1536 -/* Generic MII registers. */ - -#define MII_BMCR 0x00 /* Basic mode control register */ -#define MII_BMSR 0x01 /* Basic mode status register */ -#define MII_PHYSID1 0x02 /* PHYS ID 1 */ -#define MII_PHYSID2 0x03 /* PHYS ID 2 */ -#define MII_ADVERTISE 0x04 /* Advertisement control reg */ -#define MII_LPA 0x05 /* Link partner ability reg */ -#define MII_EXPANSION 0x06 /* Expansion register */ -#define MII_DCOUNTER 0x12 /* Disconnect counter */ -#define MII_FCSCOUNTER 0x13 /* False carrier counter */ -#define MII_NWAYTEST 0x14 /* N-way auto-neg test reg */ -#define MII_RERRCOUNTER 0x15 /* Receive error counter */ -#define MII_SREVISION 0x16 /* Silicon revision */ -#define MII_RESV1 0x17 /* Reserved... */ -#define MII_LBRERROR 0x18 /* Lpback, rx, bypass error */ -#define MII_PHYADDR 0x19 /* PHY address */ -#define MII_RESV2 0x1a /* Reserved... */ -#define MII_TPISTATUS 0x1b /* TPI status for 10mbps */ -#define MII_NCONFIG 0x1c /* Network interface config */ - -/* Basic mode control register. */ -#define BMCR_RESV 0x007f /* Unused... */ -#define BMCR_CTST 0x0080 /* Collision test */ -#define BMCR_FULLDPLX 0x0100 /* Full duplex */ -#define BMCR_ANRESTART 0x0200 /* Auto negotiation restart */ -#define BMCR_ISOLATE 0x0400 /* Disconnect DP83840 from MII */ -#define BMCR_PDOWN 0x0800 /* Powerdown the DP83840 */ -#define BMCR_ANENABLE 0x1000 /* Enable auto negotiation */ -#define BMCR_SPEED100 0x2000 /* Select 100Mbps */ -#define BMCR_LOOPBACK 0x4000 /* TXD loopback bits */ -#define BMCR_RESET 0x8000 /* Reset the DP83840 */ - -/* Basic mode status register. */ -#define BMSR_ERCAP 0x0001 /* Ext-reg capability */ -#define BMSR_JCD 0x0002 /* Jabber detected */ -#define BMSR_LSTATUS 0x0004 /* Link status */ -#define BMSR_ANEGCAPABLE 0x0008 /* Able to do auto-negotiation */ -#define BMSR_RFAULT 0x0010 /* Remote fault detected */ -#define BMSR_ANEGCOMPLETE 0x0020 /* Auto-negotiation complete */ -#define BMSR_RESV 0x07c0 /* Unused... */ -#define BMSR_10HALF 0x0800 /* Can do 10mbps, half-duplex */ -#define BMSR_10FULL 0x1000 /* Can do 10mbps, full-duplex */ -#define BMSR_100HALF 0x2000 /* Can do 100mbps, half-duplex */ -#define BMSR_100FULL 0x4000 /* Can do 100mbps, full-duplex */ -#define BMSR_100BASE4 0x8000 /* Can do 100mbps, 4k packets */ - -/* Advertisement control register. */ -#define ADVERTISE_SLCT 0x001f /* Selector bits */ -#define ADVERTISE_CSMA 0x0001 /* Only selector supported */ -#define ADVERTISE_10HALF 0x0020 /* Try for 10mbps half-duplex */ -#define ADVERTISE_10FULL 0x0040 /* Try for 10mbps full-duplex */ -#define ADVERTISE_100HALF 0x0080 /* Try for 100mbps half-duplex */ -#define ADVERTISE_100FULL 0x0100 /* Try for 100mbps full-duplex */ -#define ADVERTISE_100BASE4 0x0200 /* Try for 100mbps 4k packets */ -#define ADVERTISE_RESV 0x1c00 /* Unused... */ -#define ADVERTISE_RFAULT 0x2000 /* Say we can detect faults */ -#define ADVERTISE_LPACK 0x4000 /* Ack link partners response */ -#define ADVERTISE_NPAGE 0x8000 /* Next page bit */ - -#define ADVERTISE_FULL (ADVERTISE_100FULL | ADVERTISE_10FULL | \ - ADVERTISE_CSMA) -#define ADVERTISE_ALL (ADVERTISE_10HALF | ADVERTISE_10FULL | \ - ADVERTISE_100HALF | ADVERTISE_100FULL) - /* for different PHY */ enum phy_type_flags { MysonPHY = 1, |