| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
A switch port using 802.1x authentication will send EAP
Request-Identity packets once the physical link is up, and will not be
forwarding packets until the port identity has been established.
We do not currently support 802.1x authentication. However, a
reasonably common configuration involves using a preset list of
permitted MAC addresses, with the "authentication" taking place
between the switch and a RADIUS server. In this configuration, the
end device does not need to perform any authentication step, but does
need to be prepared for the switch port to fail to forward packets for
a substantial time after physical link-up. This exactly matches the
"blocked link" semantics already used when detecting a non-forwarding
switch port via LACP or STP.
Treat a received EAP Request-Identity as indicating a blocked link.
Unlike LACP or STP, there is no way to determine the expected time
until the next EAP packet and so we must choose a fixed timeout.
Erroneously assuming that the link is blocked is relatively harmless
since we will still attempt to transmit and receive data even over a
link that is marked as blocked, and so the net effect is merely to
prolong DHCP attempts. In contrast, erroneously assuming that the
link is unblocked will potentially cause DHCP to time out and give up,
resulting in a failed boot.
The default EAP Request-Identity interval in Cisco switches (where
this is most likely to be encountered in practice) is 30 seconds, so
choose 45 seconds as a timeout that is likely to avoid gaps during
which we falsely assume that the link is unblocked.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
|
| |
|
|
|
|
|
| |
Replace the GPL2+-only EAPoL code (currently used only for WPA) with
new code licensed under GPL2+-or-UBDL.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
|
| |
|
|
|
| |
Suggested-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
|
| |
|
|
|
|
|
|
| |
Allow the link layer to directly report whether or not a packet is
multicast or broadcast at the time of calling pull(), rather than
relying on heuristics to determine this at a later stage.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
|
| |
|
|
|
|
|
|
|
| |
FCoE requires the use of fabric-provided MAC addresses, which breaks
the assumption that the net device's MAC address is implicitly the
source address for net_tx() and the (unicast) destination address for
net_rx().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
Access to the gpxe.org and etherboot.org domains and associated
resources has been revoked by the registrant of the domain. Work
around this problem by renaming project from gPXE to iPXE, and
updating URLs to match.
Also update README, LOG and COPYRIGHTS to remove obsolete information.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
|
|
|
EAPOL is a container protocol that can wrap either EAP packets or
802.11 EAPOL-Key frames. For cleanliness' sake, add a stub that strips
the framing and sends packets off to the appropriate handler if it
is compiled in.
Signed-off-by: Marty Connor <mdc@etherboot.org>
|
