From 70f47e675e09271f66a2dfd44c4119d61b171258 Mon Sep 17 00:00:00 2001 From: Joshua Oreman Date: Sun, 2 Aug 2009 16:14:01 -0700 Subject: [sky2] Add support for Marvell Yukon-II gigabit Ethernet cards Signed-off-by: Michael Brown --- src/drivers/net/sky2.c | 2399 ++++++++++++++++++++++++++++++++++++++++++++ src/drivers/net/sky2.h | 2176 ++++++++++++++++++++++++++++++++++++++++ src/include/gpxe/errfile.h | 1 + 3 files changed, 4576 insertions(+) create mode 100644 src/drivers/net/sky2.c create mode 100644 src/drivers/net/sky2.h diff --git a/src/drivers/net/sky2.c b/src/drivers/net/sky2.c new file mode 100644 index 00000000..59b0fafb --- /dev/null +++ b/src/drivers/net/sky2.c @@ -0,0 +1,2399 @@ +/* + * gPXE driver for Marvell Yukon 2 chipset. Derived from Linux sky2 driver + * (v1.22), which was based on earlier sk98lin and skge drivers. + * + * This driver intentionally does not support all the features + * of the original driver such as link fail-over and link management because + * those should be done at higher levels. + * + * Copyright (C) 2005 Stephen Hemminger + * + * Modified for gPXE, April 2009 by Joshua Oreman + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +FILE_LICENCE ( GPL2_ONLY ); + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "sky2.h" + +#define DRV_NAME "sky2" +#define DRV_VERSION "1.22" +#define PFX DRV_NAME " " + +/* + * The Yukon II chipset takes 64 bit command blocks (called list elements) + * that are organized into three (receive, transmit, status) different rings + * similar to Tigon3. + * + * Each ring start must be aligned to a 4k boundary. You will get mysterious + * "invalid LE" errors if they're not. + * + * The card silently forces each ring size to be at least 128. If you + * act as though one of them is smaller (by setting the below + * #defines) you'll get bad bugs. + */ + +#define RX_LE_SIZE 128 +#define RX_LE_BYTES (RX_LE_SIZE*sizeof(struct sky2_rx_le)) +#define RX_RING_ALIGN 4096 +#define RX_PENDING (RX_LE_SIZE/6 - 2) + +#define TX_RING_SIZE 128 +#define TX_PENDING (TX_RING_SIZE - 1) +#define TX_RING_ALIGN 4096 +#define MAX_SKB_TX_LE 4 + +#define STATUS_RING_SIZE 512 /* 2 ports * (TX + RX) */ +#define STATUS_LE_BYTES (STATUS_RING_SIZE*sizeof(struct sky2_status_le)) +#define STATUS_RING_ALIGN 4096 +#define PHY_RETRIES 1000 + +#define SKY2_EEPROM_MAGIC 0x9955aabb + + +#define RING_NEXT(x,s) (((x)+1) & ((s)-1)) + +static struct pci_device_id sky2_id_table[] = { + PCI_ROM(0x1148, 0x9000, "sk9sxx", "Syskonnect SK-9Sxx", 0), + PCI_ROM(0x1148, 0x9e00, "sk9exx", "Syskonnect SK-9Exx", 0), + PCI_ROM(0x1186, 0x4b00, "dge560t", "D-Link DGE-560T", 0), + PCI_ROM(0x1186, 0x4001, "dge550sx", "D-Link DGE-550SX", 0), + PCI_ROM(0x1186, 0x4b02, "dge560sx", "D-Link DGE-560SX", 0), + PCI_ROM(0x1186, 0x4b03, "dge550t", "D-Link DGE-550T", 0), + PCI_ROM(0x11ab, 0x4340, "m88e8021", "Marvell 88E8021", 0), + PCI_ROM(0x11ab, 0x4341, "m88e8022", "Marvell 88E8022", 0), + PCI_ROM(0x11ab, 0x4342, "m88e8061", "Marvell 88E8061", 0), + PCI_ROM(0x11ab, 0x4343, "m88e8062", "Marvell 88E8062", 0), + PCI_ROM(0x11ab, 0x4344, "m88e8021b", "Marvell 88E8021", 0), + PCI_ROM(0x11ab, 0x4345, "m88e8022b", "Marvell 88E8022", 0), + PCI_ROM(0x11ab, 0x4346, "m88e8061b", "Marvell 88E8061", 0), + PCI_ROM(0x11ab, 0x4347, "m88e8062b", "Marvell 88E8062", 0), + PCI_ROM(0x11ab, 0x4350, "m88e8035", "Marvell 88E8035", 0), + PCI_ROM(0x11ab, 0x4351, "m88e8036", "Marvell 88E8036", 0), + PCI_ROM(0x11ab, 0x4352, "m88e8038", "Marvell 88E8038", 0), + PCI_ROM(0x11ab, 0x4353, "m88e8039", "Marvell 88E8039", 0), + PCI_ROM(0x11ab, 0x4354, "m88e8040", "Marvell 88E8040", 0), + PCI_ROM(0x11ab, 0x4355, "m88e8040t", "Marvell 88E8040T", 0), + PCI_ROM(0x11ab, 0x4356, "m88ec033", "Marvel 88EC033", 0), + PCI_ROM(0x11ab, 0x4357, "m88e8042", "Marvell 88E8042", 0), + PCI_ROM(0x11ab, 0x435a, "m88e8048", "Marvell 88E8048", 0), + PCI_ROM(0x11ab, 0x4360, "m88e8052", "Marvell 88E8052", 0), + PCI_ROM(0x11ab, 0x4361, "m88e8050", "Marvell 88E8050", 0), + PCI_ROM(0x11ab, 0x4362, "m88e8053", "Marvell 88E8053", 0), + PCI_ROM(0x11ab, 0x4363, "m88e8055", "Marvell 88E8055", 0), + PCI_ROM(0x11ab, 0x4364, "m88e8056", "Marvell 88E8056", 0), + PCI_ROM(0x11ab, 0x4365, "m88e8070", "Marvell 88E8070", 0), + PCI_ROM(0x11ab, 0x4366, "m88ec036", "Marvell 88EC036", 0), + PCI_ROM(0x11ab, 0x4367, "m88ec032", "Marvell 88EC032", 0), + PCI_ROM(0x11ab, 0x4368, "m88ec034", "Marvell 88EC034", 0), + PCI_ROM(0x11ab, 0x4369, "m88ec042", "Marvell 88EC042", 0), + PCI_ROM(0x11ab, 0x436a, "m88e8058", "Marvell 88E8058", 0), + PCI_ROM(0x11ab, 0x436b, "m88e8071", "Marvell 88E8071", 0), + PCI_ROM(0x11ab, 0x436c, "m88e8072", "Marvell 88E8072", 0), + PCI_ROM(0x11ab, 0x436d, "m88e8055b", "Marvell 88E8055", 0), + PCI_ROM(0x11ab, 0x4370, "m88e8075", "Marvell 88E8075", 0), + PCI_ROM(0x11ab, 0x4380, "m88e8057", "Marvell 88E8057", 0) +}; + +/* Avoid conditionals by using array */ +static const unsigned txqaddr[] = { Q_XA1, Q_XA2 }; +static const unsigned rxqaddr[] = { Q_R1, Q_R2 }; +static const u32 portirq_msk[] = { Y2_IS_PORT_1, Y2_IS_PORT_2 }; + +static void sky2_set_multicast(struct net_device *dev); + +/* Access to PHY via serial interconnect */ +static int gm_phy_write(struct sky2_hw *hw, unsigned port, u16 reg, u16 val) +{ + int i; + + gma_write16(hw, port, GM_SMI_DATA, val); + gma_write16(hw, port, GM_SMI_CTRL, + GM_SMI_CT_PHY_AD(PHY_ADDR_MARV) | GM_SMI_CT_REG_AD(reg)); + + for (i = 0; i < PHY_RETRIES; i++) { + u16 ctrl = gma_read16(hw, port, GM_SMI_CTRL); + if (ctrl == 0xffff) + goto io_error; + + if (!(ctrl & GM_SMI_CT_BUSY)) + return 0; + + udelay(10); + } + + DBG(PFX "%s: phy write timeout\n", hw->dev[port]->name); + return -ETIMEDOUT; + +io_error: + DBG(PFX "%s: phy I/O error\n", hw->dev[port]->name); + return -EIO; +} + +static int __gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg, u16 *val) +{ + int i; + + gma_write16(hw, port, GM_SMI_CTRL, GM_SMI_CT_PHY_AD(PHY_ADDR_MARV) + | GM_SMI_CT_REG_AD(reg) | GM_SMI_CT_OP_RD); + + for (i = 0; i < PHY_RETRIES; i++) { + u16 ctrl = gma_read16(hw, port, GM_SMI_CTRL); + if (ctrl == 0xffff) + goto io_error; + + if (ctrl & GM_SMI_CT_RD_VAL) { + *val = gma_read16(hw, port, GM_SMI_DATA); + return 0; + } + + udelay(10); + } + + DBG(PFX "%s: phy read timeout\n", hw->dev[port]->name); + return -ETIMEDOUT; +io_error: + DBG(PFX "%s: phy I/O error\n", hw->dev[port]->name); + return -EIO; +} + +static inline u16 gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg) +{ + u16 v = 0; + __gm_phy_read(hw, port, reg, &v); + return v; +} + + +static void sky2_power_on(struct sky2_hw *hw) +{ + /* switch power to VCC (WA for VAUX problem) */ + sky2_write8(hw, B0_POWER_CTRL, + PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_OFF | PC_VCC_ON); + + /* disable Core Clock Division, */ + sky2_write32(hw, B2_Y2_CLK_CTRL, Y2_CLK_DIV_DIS); + + if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1) + /* enable bits are inverted */ + sky2_write8(hw, B2_Y2_CLK_GATE, + Y2_PCI_CLK_LNK1_DIS | Y2_COR_CLK_LNK1_DIS | + Y2_CLK_GAT_LNK1_DIS | Y2_PCI_CLK_LNK2_DIS | + Y2_COR_CLK_LNK2_DIS | Y2_CLK_GAT_LNK2_DIS); + else + sky2_write8(hw, B2_Y2_CLK_GATE, 0); + + if (hw->flags & SKY2_HW_ADV_POWER_CTL) { + u32 reg; + + sky2_pci_write32(hw, PCI_DEV_REG3, 0); + + reg = sky2_pci_read32(hw, PCI_DEV_REG4); + /* set all bits to 0 except bits 15..12 and 8 */ + reg &= P_ASPM_CONTROL_MSK; + sky2_pci_write32(hw, PCI_DEV_REG4, reg); + + reg = sky2_pci_read32(hw, PCI_DEV_REG5); + /* set all bits to 0 except bits 28 & 27 */ + reg &= P_CTL_TIM_VMAIN_AV_MSK; + sky2_pci_write32(hw, PCI_DEV_REG5, reg); + + sky2_pci_write32(hw, PCI_CFG_REG_1, 0); + + /* Enable workaround for dev 4.107 on Yukon-Ultra & Extreme */ + reg = sky2_read32(hw, B2_GP_IO); + reg |= GLB_GPIO_STAT_RACE_DIS; + sky2_write32(hw, B2_GP_IO, reg); + + sky2_read32(hw, B2_GP_IO); + } +} + +static void sky2_power_aux(struct sky2_hw *hw) +{ + if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1) + sky2_write8(hw, B2_Y2_CLK_GATE, 0); + else + /* enable bits are inverted */ + sky2_write8(hw, B2_Y2_CLK_GATE, + Y2_PCI_CLK_LNK1_DIS | Y2_COR_CLK_LNK1_DIS | + Y2_CLK_GAT_LNK1_DIS | Y2_PCI_CLK_LNK2_DIS | + Y2_COR_CLK_LNK2_DIS | Y2_CLK_GAT_LNK2_DIS); + + /* switch power to VAUX */ + if (sky2_read16(hw, B0_CTST) & Y2_VAUX_AVAIL) + sky2_write8(hw, B0_POWER_CTRL, + (PC_VAUX_ENA | PC_VCC_ENA | + PC_VAUX_ON | PC_VCC_OFF)); +} + +static void sky2_gmac_reset(struct sky2_hw *hw, unsigned port) +{ + u16 reg; + + /* disable all GMAC IRQ's */ + sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), 0); + + gma_write16(hw, port, GM_MC_ADDR_H1, 0); /* clear MC hash */ + gma_write16(hw, port, GM_MC_ADDR_H2, 0); + gma_write16(hw, port, GM_MC_ADDR_H3, 0); + gma_write16(hw, port, GM_MC_ADDR_H4, 0); + + reg = gma_read16(hw, port, GM_RX_CTRL); + reg |= GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA; + gma_write16(hw, port, GM_RX_CTRL, reg); +} + +/* flow control to advertise bits */ +static const u16 copper_fc_adv[] = { + [FC_NONE] = 0, + [FC_TX] = PHY_M_AN_ASP, + [FC_RX] = PHY_M_AN_PC, + [FC_BOTH] = PHY_M_AN_PC | PHY_M_AN_ASP, +}; + +/* flow control to advertise bits when using 1000BaseX */ +static const u16 fiber_fc_adv[] = { + [FC_NONE] = PHY_M_P_NO_PAUSE_X, + [FC_TX] = PHY_M_P_ASYM_MD_X, + [FC_RX] = PHY_M_P_SYM_MD_X, + [FC_BOTH] = PHY_M_P_BOTH_MD_X, +}; + +/* flow control to GMA disable bits */ +static const u16 gm_fc_disable[] = { + [FC_NONE] = GM_GPCR_FC_RX_DIS | GM_GPCR_FC_TX_DIS, + [FC_TX] = GM_GPCR_FC_RX_DIS, + [FC_RX] = GM_GPCR_FC_TX_DIS, + [FC_BOTH] = 0, +}; + + +static void sky2_phy_init(struct sky2_hw *hw, unsigned port) +{ + struct sky2_port *sky2 = netdev_priv(hw->dev[port]); + u16 ctrl, ct1000, adv, pg, ledctrl, ledover, reg; + + if (sky2->autoneg == AUTONEG_ENABLE && + !(hw->flags & SKY2_HW_NEWER_PHY)) { + u16 ectrl = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL); + + ectrl &= ~(PHY_M_EC_M_DSC_MSK | PHY_M_EC_S_DSC_MSK | + PHY_M_EC_MAC_S_MSK); + ectrl |= PHY_M_EC_MAC_S(MAC_TX_CLK_25_MHZ); + + /* on PHY 88E1040 Rev.D0 (and newer) downshift control changed */ + if (hw->chip_id == CHIP_ID_YUKON_EC) + /* set downshift counter to 3x and enable downshift */ + ectrl |= PHY_M_EC_DSC_2(2) | PHY_M_EC_DOWN_S_ENA; + else + /* set master & slave downshift counter to 1x */ + ectrl |= PHY_M_EC_M_DSC(0) | PHY_M_EC_S_DSC(1); + + gm_phy_write(hw, port, PHY_MARV_EXT_CTRL, ectrl); + } + + ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); + if (sky2_is_copper(hw)) { + if (!(hw->flags & SKY2_HW_GIGABIT)) { + /* enable automatic crossover */ + ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO) >> 1; + + if (hw->chip_id == CHIP_ID_YUKON_FE_P && + hw->chip_rev == CHIP_REV_YU_FE2_A0) { + u16 spec; + + /* Enable Class A driver for FE+ A0 */ + spec = gm_phy_read(hw, port, PHY_MARV_FE_SPEC_2); + spec |= PHY_M_FESC_SEL_CL_A; + gm_phy_write(hw, port, PHY_MARV_FE_SPEC_2, spec); + } + } else { + /* disable energy detect */ + ctrl &= ~PHY_M_PC_EN_DET_MSK; + + /* enable automatic crossover */ + ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO); + + /* downshift on PHY 88E1112 and 88E1149 is changed */ + if (sky2->autoneg == AUTONEG_ENABLE + && (hw->flags & SKY2_HW_NEWER_PHY)) { + /* set downshift counter to 3x and enable downshift */ + ctrl &= ~PHY_M_PC_DSC_MSK; + ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA; + } + } + } else { + /* workaround for deviation #4.88 (CRC errors) */ + /* disable Automatic Crossover */ + + ctrl &= ~PHY_M_PC_MDIX_MSK; + } + + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); + + /* special setup for PHY 88E1112 Fiber */ + if (hw->chip_id == CHIP_ID_YUKON_XL && (hw->flags & SKY2_HW_FIBRE_PHY)) { + pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR); + + /* Fiber: select 1000BASE-X only mode MAC Specific Ctrl Reg. */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2); + ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); + ctrl &= ~PHY_M_MAC_MD_MSK; + ctrl |= PHY_M_MAC_MODE_SEL(PHY_M_MAC_MD_1000BX); + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); + + if (hw->pmd_type == 'P') { + /* select page 1 to access Fiber registers */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 1); + + /* for SFP-module set SIGDET polarity to low */ + ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); + ctrl |= PHY_M_FIB_SIGD_POL; + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); + } + + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg); + } + + ctrl = PHY_CT_RESET; + ct1000 = 0; + adv = PHY_AN_CSMA; + reg = 0; + + if (sky2->autoneg == AUTONEG_ENABLE) { + if (sky2_is_copper(hw)) { + if (sky2->advertising & ADVERTISED_1000baseT_Full) + ct1000 |= PHY_M_1000C_AFD; + if (sky2->advertising & ADVERTISED_1000baseT_Half) + ct1000 |= PHY_M_1000C_AHD; + if (sky2->advertising & ADVERTISED_100baseT_Full) + adv |= PHY_M_AN_100_FD; + if (sky2->advertising & ADVERTISED_100baseT_Half) + adv |= PHY_M_AN_100_HD; + if (sky2->advertising & ADVERTISED_10baseT_Full) + adv |= PHY_M_AN_10_FD; + if (sky2->advertising & ADVERTISED_10baseT_Half) + adv |= PHY_M_AN_10_HD; + + adv |= copper_fc_adv[sky2->flow_mode]; + } else { /* special defines for FIBER (88E1040S only) */ + if (sky2->advertising & ADVERTISED_1000baseT_Full) + adv |= PHY_M_AN_1000X_AFD; + if (sky2->advertising & ADVERTISED_1000baseT_Half) + adv |= PHY_M_AN_1000X_AHD; + + adv |= fiber_fc_adv[sky2->flow_mode]; + } + + /* Restart Auto-negotiation */ + ctrl |= PHY_CT_ANE | PHY_CT_RE_CFG; + } else { + /* forced speed/duplex settings */ + ct1000 = PHY_M_1000C_MSE; + + /* Disable auto update for duplex flow control and speed */ + reg |= GM_GPCR_AU_ALL_DIS; + + switch (sky2->speed) { + case SPEED_1000: + ctrl |= PHY_CT_SP1000; + reg |= GM_GPCR_SPEED_1000; + break; + case SPEED_100: + ctrl |= PHY_CT_SP100; + reg |= GM_GPCR_SPEED_100; + break; + } + + if (sky2->duplex == DUPLEX_FULL) { + reg |= GM_GPCR_DUP_FULL; + ctrl |= PHY_CT_DUP_MD; + } else if (sky2->speed < SPEED_1000) + sky2->flow_mode = FC_NONE; + + + reg |= gm_fc_disable[sky2->flow_mode]; + + /* Forward pause packets to GMAC? */ + if (sky2->flow_mode & FC_RX) + sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON); + else + sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF); + } + + gma_write16(hw, port, GM_GP_CTRL, reg); + + if (hw->flags & SKY2_HW_GIGABIT) + gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, ct1000); + + gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, adv); + gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl); + + /* Setup Phy LED's */ + ledctrl = PHY_M_LED_PULS_DUR(PULS_170MS); + ledover = 0; + + switch (hw->chip_id) { + case CHIP_ID_YUKON_FE: + /* on 88E3082 these bits are at 11..9 (shifted left) */ + ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) << 1; + + ctrl = gm_phy_read(hw, port, PHY_MARV_FE_LED_PAR); + + /* delete ACT LED control bits */ + ctrl &= ~PHY_M_FELP_LED1_MSK; + /* change ACT LED control to blink mode */ + ctrl |= PHY_M_FELP_LED1_CTRL(LED_PAR_CTRL_ACT_BL); + gm_phy_write(hw, port, PHY_MARV_FE_LED_PAR, ctrl); + break; + + case CHIP_ID_YUKON_FE_P: + /* Enable Link Partner Next Page */ + ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); + ctrl |= PHY_M_PC_ENA_LIP_NP; + + /* disable Energy Detect and enable scrambler */ + ctrl &= ~(PHY_M_PC_ENA_ENE_DT | PHY_M_PC_DIS_SCRAMB); + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); + + /* set LED2 -> ACT, LED1 -> LINK, LED0 -> SPEED */ + ctrl = PHY_M_FELP_LED2_CTRL(LED_PAR_CTRL_ACT_BL) | + PHY_M_FELP_LED1_CTRL(LED_PAR_CTRL_LINK) | + PHY_M_FELP_LED0_CTRL(LED_PAR_CTRL_SPEED); + + gm_phy_write(hw, port, PHY_MARV_FE_LED_PAR, ctrl); + break; + + case CHIP_ID_YUKON_XL: + pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR); + + /* select page 3 to access LED control register */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3); + + /* set LED Function Control register */ + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, + (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */ + PHY_M_LEDC_INIT_CTRL(7) | /* 10 Mbps */ + PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */ + PHY_M_LEDC_STA0_CTRL(7))); /* 1000 Mbps */ + + /* set Polarity Control register */ + gm_phy_write(hw, port, PHY_MARV_PHY_STAT, + (PHY_M_POLC_LS1_P_MIX(4) | + PHY_M_POLC_IS0_P_MIX(4) | + PHY_M_POLC_LOS_CTRL(2) | + PHY_M_POLC_INIT_CTRL(2) | + PHY_M_POLC_STA1_CTRL(2) | + PHY_M_POLC_STA0_CTRL(2))); + + /* restore page register */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg); + break; + + case CHIP_ID_YUKON_EC_U: + case CHIP_ID_YUKON_EX: + case CHIP_ID_YUKON_SUPR: + pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR); + + /* select page 3 to access LED control register */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3); + + /* set LED Function Control register */ + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, + (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */ + PHY_M_LEDC_INIT_CTRL(8) | /* 10 Mbps */ + PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */ + PHY_M_LEDC_STA0_CTRL(7)));/* 1000 Mbps */ + + /* set Blink Rate in LED Timer Control Register */ + gm_phy_write(hw, port, PHY_MARV_INT_MASK, + ledctrl | PHY_M_LED_BLINK_RT(BLINK_84MS)); + /* restore page register */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg); + break; + + default: + /* set Tx LED (LED_TX) to blink mode on Rx OR Tx activity */ + ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) | PHY_M_LEDC_TX_CTRL; + + /* turn off the Rx LED (LED_RX) */ + ledover |= PHY_M_LED_MO_RX(MO_LED_OFF); + } + + if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_UL_2) { + /* apply fixes in PHY AFE */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 255); + + /* increase differential signal amplitude in 10BASE-T */ + gm_phy_write(hw, port, 0x18, 0xaa99); + gm_phy_write(hw, port, 0x17, 0x2011); + + if (hw->chip_id == CHIP_ID_YUKON_EC_U) { + /* fix for IEEE A/B Symmetry failure in 1000BASE-T */ + gm_phy_write(hw, port, 0x18, 0xa204); + gm_phy_write(hw, port, 0x17, 0x2002); + } + + /* set page register to 0 */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0); + } else if (hw->chip_id == CHIP_ID_YUKON_FE_P && + hw->chip_rev == CHIP_REV_YU_FE2_A0) { + /* apply workaround for integrated resistors calibration */ + gm_phy_write(hw, port, PHY_MARV_PAGE_ADDR, 17); + gm_phy_write(hw, port, PHY_MARV_PAGE_DATA, 0x3f60); + } else if (hw->chip_id != CHIP_ID_YUKON_EX && + hw->chip_id < CHIP_ID_YUKON_SUPR) { + /* no effect on Yukon-XL */ + gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl); + + if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) { + /* turn on 100 Mbps LED (LED_LINK100) */ + ledover |= PHY_M_LED_MO_100(MO_LED_ON); + } + + if (ledover) + gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover); + + } + + /* Enable phy interrupt on auto-negotiation complete (or link up) */ + if (sky2->autoneg == AUTONEG_ENABLE) + gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_COMPL); + else + gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK); +} + +static const u32 phy_power[] = { PCI_Y2_PHY1_POWD, PCI_Y2_PHY2_POWD }; +static const u32 coma_mode[] = { PCI_Y2_PHY1_COMA, PCI_Y2_PHY2_COMA }; + +static void sky2_phy_power_up(struct sky2_hw *hw, unsigned port) +{ + u32 reg1; + + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); + reg1 = sky2_pci_read32(hw, PCI_DEV_REG1); + reg1 &= ~phy_power[port]; + + if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1) + reg1 |= coma_mode[port]; + + sky2_pci_write32(hw, PCI_DEV_REG1, reg1); + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); + sky2_pci_read32(hw, PCI_DEV_REG1); + + if (hw->chip_id == CHIP_ID_YUKON_FE) + gm_phy_write(hw, port, PHY_MARV_CTRL, PHY_CT_ANE); + else if (hw->flags & SKY2_HW_ADV_POWER_CTL) + sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR); +} + +static void sky2_phy_power_down(struct sky2_hw *hw, unsigned port) +{ + u32 reg1; + u16 ctrl; + + /* release GPHY Control reset */ + sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR); + + /* release GMAC reset */ + sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR); + + if (hw->flags & SKY2_HW_NEWER_PHY) { + /* select page 2 to access MAC control register */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2); + + ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); + /* allow GMII Power Down */ + ctrl &= ~PHY_M_MAC_GMIF_PUP; + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); + + /* set page register back to 0 */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0); + } + + /* setup General Purpose Control Register */ + gma_write16(hw, port, GM_GP_CTRL, + GM_GPCR_FL_PASS | GM_GPCR_SPEED_100 | GM_GPCR_AU_ALL_DIS); + + if (hw->chip_id != CHIP_ID_YUKON_EC) { + if (hw->chip_id == CHIP_ID_YUKON_EC_U) { + /* select page 2 to access MAC control register */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2); + + ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); + /* enable Power Down */ + ctrl |= PHY_M_PC_POW_D_ENA; + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); + + /* set page register back to 0 */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0); + } + + /* set IEEE compatible Power Down Mode (dev. #4.99) */ + gm_phy_write(hw, port, PHY_MARV_CTRL, PHY_CT_PDOWN); + } + + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); + reg1 = sky2_pci_read32(hw, PCI_DEV_REG1); + reg1 |= phy_power[port]; /* set PHY to PowerDown/COMA Mode */ + sky2_pci_write32(hw, PCI_DEV_REG1, reg1); + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); +} + +static void sky2_set_tx_stfwd(struct sky2_hw *hw, unsigned port) +{ + if ( (hw->chip_id == CHIP_ID_YUKON_EX && + hw->chip_rev != CHIP_REV_YU_EX_A0) || + hw->chip_id == CHIP_ID_YUKON_FE_P || + hw->chip_id == CHIP_ID_YUKON_SUPR) { + /* disable jumbo frames on devices that support them */ + sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), + TX_JUMBO_DIS | TX_STFW_ENA); + } else { + sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_STFW_ENA); + } +} + +static void sky2_mac_init(struct sky2_hw *hw, unsigned port) +{ + u16 reg; + u32 rx_reg; + int i; + const u8 *addr = hw->dev[port]->ll_addr; + + sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET); + sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR); + + sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR); + + if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0 && port == 1) { + /* WA DEV_472 -- looks like crossed wires on port 2 */ + /* clear GMAC 1 Control reset */ + sky2_write8(hw, SK_REG(0, GMAC_CTRL), GMC_RST_CLR); + do { + sky2_write8(hw, SK_REG(1, GMAC_CTRL), GMC_RST_SET); + sky2_write8(hw, SK_REG(1, GMAC_CTRL), GMC_RST_CLR); + } while (gm_phy_read(hw, 1, PHY_MARV_ID0) != PHY_MARV_ID0_VAL || + gm_phy_read(hw, 1, PHY_MARV_ID1) != PHY_MARV_ID1_Y2 || + gm_phy_read(hw, 1, PHY_MARV_INT_MASK) != 0); + } + + sky2_read16(hw, SK_REG(port, GMAC_IRQ_SRC)); + + /* Enable Transmit FIFO Underrun */ + sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), GMAC_DEF_MSK); + + sky2_phy_power_up(hw, port); + sky2_phy_init(hw, port); + + /* MIB clear */ + reg = gma_read16(hw, port, GM_PHY_ADDR); + gma_write16(hw, port, GM_PHY_ADDR, reg | GM_PAR_MIB_CLR); + + for (i = GM_MIB_CNT_BASE; i <= GM_MIB_CNT_END; i += 4) + gma_read16(hw, port, i); + gma_write16(hw, port, GM_PHY_ADDR, reg); + + /* transmit control */ + gma_write16(hw, port, GM_TX_CTRL, TX_COL_THR(TX_COL_DEF)); + + /* receive control reg: unicast + multicast + no FCS */ + gma_write16(hw, port, GM_RX_CTRL, + GM_RXCR_UCF_ENA | GM_RXCR_CRC_DIS | GM_RXCR_MCF_ENA); + + /* transmit flow control */ + gma_write16(hw, port, GM_TX_FLOW_CTRL, 0xffff); + + /* transmit parameter */ + gma_write16(hw, port, GM_TX_PARAM, + TX_JAM_LEN_VAL(TX_JAM_LEN_DEF) | + TX_JAM_IPG_VAL(TX_JAM_IPG_DEF) | + TX_IPG_JAM_DATA(TX_IPG_JAM_DEF) | + TX_BACK_OFF_LIM(TX_BOF_LIM_DEF)); + + /* serial mode register */ + reg = DATA_BLIND_VAL(DATA_BLIND_DEF) | + GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF); + + gma_write16(hw, port, GM_SERIAL_MODE, reg); + + /* virtual address for data */ + gma_set_addr(hw, port, GM_SRC_ADDR_2L, addr); + + /* physical address: used for pause frames */ + gma_set_addr(hw, port, GM_SRC_ADDR_1L, addr); + + /* ignore counter overflows */ + gma_write16(hw, port, GM_TX_IRQ_MSK, 0); + gma_write16(hw, port, GM_RX_IRQ_MSK, 0); + gma_write16(hw, port, GM_TR_IRQ_MSK, 0); + + /* Configure Rx MAC FIFO */ + sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR); + rx_reg = GMF_OPER_ON | GMF_RX_F_FL_ON; + if (hw->chip_id == CHIP_ID_YUKON_EX || + hw->chip_id == CHIP_ID_YUKON_FE_P) + rx_reg |= GMF_RX_OVER_ON; + + sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), rx_reg); + + if (hw->chip_id == CHIP_ID_YUKON_XL) { + /* Hardware errata - clear flush mask */ + sky2_write16(hw, SK_REG(port, RX_GMF_FL_MSK), 0); + } else { + /* Flush Rx MAC FIFO on any flow control or error */ + sky2_write16(hw, SK_REG(port, RX_GMF_FL_MSK), GMR_FS_ANY_ERR); + } + + /* Set threshold to 0xa (64 bytes) + 1 to workaround pause bug */ + reg = RX_GMF_FL_THR_DEF + 1; + /* Another magic mystery workaround from sk98lin */ + if (hw->chip_id == CHIP_ID_YUKON_FE_P && + hw->chip_rev == CHIP_REV_YU_FE2_A0) + reg = 0x178; + sky2_write16(hw, SK_REG(port, RX_GMF_FL_THR), reg); + + /* Configure Tx MAC FIFO */ + sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR); + sky2_write16(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_OPER_ON); + + /* On chips without ram buffer, pause is controled by MAC level */ + if (!(hw->flags & SKY2_HW_RAM_BUFFER)) { + sky2_write8(hw, SK_REG(port, RX_GMF_LP_THR), 768/8); + sky2_write8(hw, SK_REG(port, RX_GMF_UP_THR), 1024/8); + + sky2_set_tx_stfwd(hw, port); + } + + if (hw->chip_id == CHIP_ID_YUKON_FE_P && + hw->chip_rev == CHIP_REV_YU_FE2_A0) { + /* disable dynamic watermark */ + reg = sky2_read16(hw, SK_REG(port, TX_GMF_EA)); + reg &= ~TX_DYN_WM_ENA; + sky2_write16(hw, SK_REG(port, TX_GMF_EA), reg); + } +} + +/* Assign Ram Buffer allocation to queue */ +static void sky2_ramset(struct sky2_hw *hw, u16 q, u32 start, u32 space) +{ + u32 end; + + /* convert from K bytes to qwords used for hw register */ + start *= 1024/8; + space *= 1024/8; + end = start + space - 1; + + sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_RST_CLR); + sky2_write32(hw, RB_ADDR(q, RB_START), start); + sky2_write32(hw, RB_ADDR(q, RB_END), end); + sky2_write32(hw, RB_ADDR(q, RB_WP), start); + sky2_write32(hw, RB_ADDR(q, RB_RP), start); + + if (q == Q_R1 || q == Q_R2) { + u32 tp = space - space/4; + + /* On receive queue's set the thresholds + * give receiver priority when > 3/4 full + * send pause when down to 2K + */ + sky2_write32(hw, RB_ADDR(q, RB_RX_UTHP), tp); + sky2_write32(hw, RB_ADDR(q, RB_RX_LTHP), space/2); + + tp = space - 2048/8; + sky2_write32(hw, RB_ADDR(q, RB_RX_UTPP), tp); + sky2_write32(hw, RB_ADDR(q, RB_RX_LTPP), space/4); + } else { + /* Enable store & forward on Tx queue's because + * Tx FIFO is only 1K on Yukon + */ + sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_STFWD); + } + + sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_OP_MD); + sky2_read8(hw, RB_ADDR(q, RB_CTRL)); +} + +/* Setup Bus Memory Interface */ +static void sky2_qset(struct sky2_hw *hw, u16 q) +{ + sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_CLR_RESET); + sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_OPER_INIT); + sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_FIFO_OP_ON); + sky2_write32(hw, Q_ADDR(q, Q_WM), BMU_WM_DEFAULT); +} + +/* Setup prefetch unit registers. This is the interface between + * hardware and driver list elements + */ +static void sky2_prefetch_init(struct sky2_hw *hw, u32 qaddr, + u64 addr, u32 last) +{ + sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_RST_SET); + sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_RST_CLR); + sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_ADDR_HI), addr >> 32); + sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_ADDR_LO), (u32) addr); + sky2_write16(hw, Y2_QADDR(qaddr, PREF_UNIT_LAST_IDX), last); + sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_OP_ON); + + sky2_read32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL)); +} + +static inline struct sky2_tx_le *get_tx_le(struct sky2_port *sky2) +{ + struct sky2_tx_le *le = sky2->tx_le + sky2->tx_prod; + + sky2->tx_prod = RING_NEXT(sky2->tx_prod, TX_RING_SIZE); + le->ctrl = 0; + return le; +} + +static void tx_init(struct sky2_port *sky2) +{ + struct sky2_tx_le *le; + + sky2->tx_prod = sky2->tx_cons = 0; + + le = get_tx_le(sky2); + le->addr = 0; + le->opcode = OP_ADDR64 | HW_OWNER; +} + +static inline struct tx_ring_info *tx_le_re(struct sky2_port *sky2, + struct sky2_tx_le *le) +{ + return sky2->tx_ring + (le - sky2->tx_le); +} + +/* Update chip's next pointer */ +static inline void sky2_put_idx(struct sky2_hw *hw, unsigned q, u16 idx) +{ + /* Make sure write' to descriptors are complete before we tell hardware */ + wmb(); + sky2_write16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX), idx); + DBGIO(PFX "queue %#x idx <- %d\n", q, idx); +} + + +static inline struct sky2_rx_le *sky2_next_rx(struct sky2_port *sky2) +{ + struct sky2_rx_le *le = sky2->rx_le + sky2->rx_put; + + sky2->rx_put = RING_NEXT(sky2->rx_put, RX_LE_SIZE); + le->ctrl = 0; + return le; +} + +/* Build description to hardware for one receive segment */ +static void sky2_rx_add(struct sky2_port *sky2, u8 op, + u32 map, unsigned len) +{ + struct sky2_rx_le *le; + + le = sky2_next_rx(sky2); + le->addr = cpu_to_le32(map); + le->length = cpu_to_le16(len); + le->opcode = op | HW_OWNER; +} + +/* Build description to hardware for one possibly fragmented skb */ +static void sky2_rx_submit(struct sky2_port *sky2, + const struct rx_ring_info *re) +{ + sky2_rx_add(sky2, OP_PACKET, re->data_addr, sky2->rx_data_size); +} + + +static void sky2_rx_map_iob(struct pci_device *pdev __unused, + struct rx_ring_info *re, + unsigned size __unused) +{ + struct io_buffer *iob = re->iob; + re->data_addr = virt_to_bus(iob->data); +} + +/* Diable the checksum offloading. + */ +static void rx_set_checksum(struct sky2_port *sky2) +{ + struct sky2_rx_le *le = sky2_next_rx(sky2); + + le->addr = cpu_to_le32((ETH_HLEN << 16) | ETH_HLEN); + le->ctrl = 0; + le->opcode = OP_TCPSTART | HW_OWNER; + + sky2_write32(sky2->hw, + Q_ADDR(rxqaddr[sky2->port], Q_CSR), + BMU_DIS_RX_CHKSUM); +} + +/* + * The RX Stop command will not work for Yukon-2 if the BMU does not + * reach the end of packet and since we can't make sure that we have + * incoming data, we must reset the BMU while it is not doing a DMA + * transfer. Since it is possible that the RX path is still active, + * the RX RAM buffer will be stopped first, so any possible incoming + * data will not trigger a DMA. After the RAM buffer is stopped, the + * BMU is polled until any DMA in progress is ended and only then it + * will be reset. + */ +static void sky2_rx_stop(struct sky2_port *sky2) +{ + struct sky2_hw *hw = sky2->hw; + unsigned rxq = rxqaddr[sky2->port]; + int i; + + /* disable the RAM Buffer receive queue */ + sky2_write8(hw, RB_ADDR(rxq, RB_CTRL), RB_DIS_OP_MD); + + for (i = 0; i < 0xffff; i++) + if (sky2_read8(hw, RB_ADDR(rxq, Q_RSL)) + == sky2_read8(hw, RB_ADDR(rxq, Q_RL))) + goto stopped; + + DBG(PFX "%s: receiver stop failed\n", sky2->netdev->name); +stopped: + sky2_write32(hw, Q_ADDR(rxq, Q_CSR), BMU_RST_SET | BMU_FIFO_RST); + + /* reset the Rx prefetch unit */ + sky2_write32(hw, Y2_QADDR(rxq, PREF_UNIT_CTRL), PREF_UNIT_RST_SET); + wmb(); +} + +/* Clean out receive buffer area, assumes receiver hardware stopped */ +static void sky2_rx_clean(struct sky2_port *sky2) +{ + unsigned i; + + memset(sky2->rx_le, 0, RX_LE_BYTES); + for (i = 0; i < RX_PENDING; i++) { + struct rx_ring_info *re = sky2->rx_ring + i; + + if (re->iob) { + free_iob(re->iob); + re->iob = NULL; + } + } +} + +/* + * Allocate an iob for receiving. + */ +static struct io_buffer *sky2_rx_alloc(struct sky2_port *sky2) +{ + struct io_buffer *iob; + + iob = alloc_iob(sky2->rx_data_size + ETH_DATA_ALIGN); + if (!iob) + return NULL; + + /* + * Cards with a RAM buffer hang in the rx FIFO if the + * receive buffer isn't aligned to (Linux module comments say + * 64 bytes, Linux module code says 8 bytes). Since io_buffers + * are always 2kb-aligned under gPXE, just leave it be + * without ETH_DATA_ALIGN in those cases. + * + * XXX This causes unaligned access to the IP header, + * which is undesirable, but it's less undesirable than the + * card hanging. + */ + if (!(sky2->hw->flags & SKY2_HW_RAM_BUFFER)) { + iob_reserve(iob, ETH_DATA_ALIGN); + } + + return iob; +} + +static inline void sky2_rx_update(struct sky2_port *sky2, unsigned rxq) +{ + sky2_put_idx(sky2->hw, rxq, sky2->rx_put); +} + +/* + * Allocate and setup receiver buffer pool. + * Normal case this ends up creating one list element for skb + * in the receive ring. One element is used for checksum + * enable/disable, and one extra to avoid wrap. + */ +static int sky2_rx_start(struct sky2_port *sky2) +{ + struct sky2_hw *hw = sky2->hw; + struct rx_ring_info *re; + unsigned rxq = rxqaddr[sky2->port]; + unsigned i, size, thresh; + + sky2->rx_put = sky2->rx_next = 0; + sky2_qset(hw, rxq); + + /* On PCI express lowering the watermark gives better performance */ + if (pci_find_capability(hw->pdev, PCI_CAP_ID_EXP)) + sky2_write32(hw, Q_ADDR(rxq, Q_WM), BMU_WM_PEX); + + /* These chips have no ram buffer? + * MAC Rx RAM Read is controlled by hardware */ + if (hw->chip_id == CHIP_ID_YUKON_EC_U && + (hw->chip_rev == CHIP_REV_YU_EC_U_A1 + || hw->chip_rev == CHIP_REV_YU_EC_U_B0)) + sky2_write32(hw, Q_ADDR(rxq, Q_TEST), F_M_RX_RAM_DIS); + + sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1); + + if (!(hw->flags & SKY2_HW_NEW_LE)) + rx_set_checksum(sky2); + + /* Space needed for frame data + headers rounded up */ + size = (ETH_FRAME_LEN + 8) & ~7; + + /* Stopping point for hardware truncation */ + thresh = (size - 8) / sizeof(u32); + + sky2->rx_data_size = size; + + /* Fill Rx ring */ + for (i = 0; i < RX_PENDING; i++) { + re = sky2->rx_ring + i; + + re->iob = sky2_rx_alloc(sky2); + if (!re->iob) + goto nomem; + + sky2_rx_map_iob(hw->pdev, re, sky2->rx_data_size); + sky2_rx_submit(sky2, re); + } + + /* + * The receiver hangs if it receives frames larger than the + * packet buffer. As a workaround, truncate oversize frames, but + * the register is limited to 9 bits, so if you do frames > 2052 + * you better get the MTU right! + */ + if (thresh > 0x1ff) + sky2_write32(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), RX_TRUNC_OFF); + else { + sky2_write16(hw, SK_REG(sky2->port, RX_GMF_TR_THR), thresh); + sky2_write32(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), RX_TRUNC_ON); + } + + /* Tell chip about available buffers */ + sky2_rx_update(sky2, rxq); + return 0; +nomem: + sky2_rx_clean(sky2); + return -ENOMEM; +} + +/* Free the le and ring buffers */ +static void sky2_free_rings(struct sky2_port *sky2) +{ + free_dma(sky2->rx_le, RX_LE_BYTES); + free(sky2->rx_ring); + + free_dma(sky2->tx_le, TX_RING_SIZE * sizeof(struct sky2_tx_le)); + free(sky2->tx_ring); + + sky2->tx_le = NULL; + sky2->rx_le = NULL; + + sky2->rx_ring = NULL; + sky2->tx_ring = NULL; +} + +/* Bring up network interface. */ +static int sky2_up(struct net_device *dev) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + u32 imask, ramsize; + int err = -ENOMEM; + + netdev_link_down(dev); + + /* must be power of 2 */ + sky2->tx_le = malloc_dma(TX_RING_SIZE * sizeof(struct sky2_tx_le), TX_RING_ALIGN); + sky2->tx_le_map = virt_to_bus(sky2->tx_le); + if (!sky2->tx_le) + goto err_out; + memset(sky2->tx_le, 0, TX_RING_SIZE * sizeof(struct sky2_tx_le)); + + sky2->tx_ring = zalloc(TX_RING_SIZE * sizeof(struct tx_ring_info)); + if (!sky2->tx_ring) + goto err_out; + + tx_init(sky2); + + sky2->rx_le = malloc_dma(RX_LE_BYTES, RX_RING_ALIGN); + sky2->rx_le_map = virt_to_bus(sky2->rx_le); + if (!sky2->rx_le) + goto err_out; + memset(sky2->rx_le, 0, RX_LE_BYTES); + + sky2->rx_ring = zalloc(RX_PENDING * sizeof(struct rx_ring_info)); + if (!sky2->rx_ring) + goto err_out; + + sky2_mac_init(hw, port); + + /* Register is number of 4K blocks on internal RAM buffer. */ + ramsize = sky2_read8(hw, B2_E_0) * 4; + if (ramsize > 0) { + u32 rxspace; + + hw->flags |= SKY2_HW_RAM_BUFFER; + DBG2(PFX "%s: ram buffer %dK\n", dev->name, ramsize); + if (ramsize < 16) + rxspace = ramsize / 2; + else + rxspace = 8 + (2*(ramsize - 16))/3; + + sky2_ramset(hw, rxqaddr[port], 0, rxspace); + sky2_ramset(hw, txqaddr[port], rxspace, ramsize - rxspace); + + /* Make sure SyncQ is disabled */ + sky2_write8(hw, RB_ADDR(port == 0 ? Q_XS1 : Q_XS2, RB_CTRL), + RB_RST_SET); + } + + sky2_qset(hw, txqaddr[port]); + + /* This is copied from sk98lin 10.0.5.3; no one tells me about erratta's */ + if (hw->chip_id == CHIP_ID_YUKON_EX && hw->chip_rev == CHIP_REV_YU_EX_B0) + sky2_write32(hw, Q_ADDR(txqaddr[port], Q_TEST), F_TX_CHK_AUTO_OFF); + + /* Set almost empty threshold */ + if (hw->chip_id == CHIP_ID_YUKON_EC_U + && hw->chip_rev == CHIP_REV_YU_EC_U_A0) + sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), ECU_TXFF_LEV); + + sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map, + TX_RING_SIZE - 1); + + err = sky2_rx_start(sky2); + if (err) + goto err_out; + + /* Enable interrupts from phy/mac for port */ + imask = sky2_read32(hw, B0_IMSK); + imask |= portirq_msk[port]; + sky2_write32(hw, B0_IMSK, imask); + + DBGIO(PFX "%s: le bases: st %p [%x], rx %p [%x], tx %p [%x]\n", + dev->name, hw->st_le, hw->st_dma, sky2->rx_le, sky2->rx_le_map, + sky2->tx_le, sky2->tx_le_map); + + sky2_set_multicast(dev); + return 0; + +err_out: + sky2_free_rings(sky2); + return err; +} + +/* Modular subtraction in ring */ +static inline int tx_dist(unsigned tail, unsigned head) +{ + return (head - tail) & (TX_RING_SIZE - 1); +} + +/* Number of list elements available for next tx */ +static inline int tx_avail(const struct sky2_port *sky2) +{ + return TX_PENDING - tx_dist(sky2->tx_cons, sky2->tx_prod); +} + + +/* + * Put one packet in ring for transmit. + * A single packet can generate multiple list elements, and + * the number of ring elements will probably be less than the number + * of list elements used. + */ +static int sky2_xmit_frame(struct net_device *dev, struct io_buffer *iob) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + struct sky2_tx_le *le = NULL; + struct tx_ring_info *re; + unsigned len; + u32 mapping; + u8 ctrl; + + if (tx_avail(sky2) < 1) + return -EBUSY; + + len = iob_len(iob); + mapping = virt_to_bus(iob->data); + + DBGIO(PFX "%s: tx queued, slot %d, len %d\n", dev->name, + sky2->tx_prod, len); + + ctrl = 0; + + le = get_tx_le(sky2); + le->addr = cpu_to_le32((u32) mapping); + le->length = cpu_to_le16(len); + le->ctrl = ctrl; + le->opcode = (OP_PACKET | HW_OWNER); + + re = tx_le_re(sky2, le); + re->iob = iob; + + le->ctrl |= EOP; + + sky2_put_idx(hw, txqaddr[sky2->port], sky2->tx_prod); + + return 0; +} + +/* + * Free ring elements from starting at tx_cons until "done" + * + * NB: the hardware will tell us about partial completion of multi-part + * buffers so make sure not to free iob too early. + */ +static void sky2_tx_complete(struct sky2_port *sky2, u16 done) +{ + struct net_device *dev = sky2->netdev; + unsigned idx; + + assert(done < TX_RING_SIZE); + + for (idx = sky2->tx_cons; idx != done; + idx = RING_NEXT(idx, TX_RING_SIZE)) { + struct sky2_tx_le *le = sky2->tx_le + idx; + struct tx_ring_info *re = sky2->tx_ring + idx; + + if (le->ctrl & EOP) { + DBGIO(PFX "%s: tx done %d\n", dev->name, idx); + netdev_tx_complete(dev, re->iob); + } + } + + sky2->tx_cons = idx; + mb(); +} + +/* Cleanup all untransmitted buffers, assume transmitter not running */ +static void sky2_tx_clean(struct net_device *dev) +{ + struct sky2_port *sky2 = netdev_priv(dev); + + sky2_tx_complete(sky2, sky2->tx_prod); +} + +/* Network shutdown */ +static void sky2_down(struct net_device *dev) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + u16 ctrl; + u32 imask; + + /* Never really got started! */ + if (!sky2->tx_le) + return; + + DBG2(PFX "%s: disabling interface\n", dev->name); + + /* Disable port IRQ */ + imask = sky2_read32(hw, B0_IMSK); + imask &= ~portirq_msk[port]; + sky2_write32(hw, B0_IMSK, imask); + + sky2_gmac_reset(hw, port); + + /* Stop transmitter */ + sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_STOP); + sky2_read32(hw, Q_ADDR(txqaddr[port], Q_CSR)); + + sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL), + RB_RST_SET | RB_DIS_OP_MD); + + ctrl = gma_read16(hw, port, GM_GP_CTRL); + ctrl &= ~(GM_GPCR_TX_ENA | GM_GPCR_RX_ENA); + gma_write16(hw, port, GM_GP_CTRL, ctrl); + + sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET); + + /* Workaround shared GMAC reset */ + if (!(hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0 + && port == 0 && hw->dev[1])) + sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_SET); + + /* Disable Force Sync bit and Enable Alloc bit */ + sky2_write8(hw, SK_REG(port, TXA_CTRL), + TXA_DIS_FSYNC | TXA_DIS_ALLOC | TXA_STOP_RC); + + /* Stop Interval Timer and Limit Counter of Tx Arbiter */ + sky2_write32(hw, SK_REG(port, TXA_ITI_INI), 0L); + sky2_write32(hw, SK_REG(port, TXA_LIM_INI), 0L); + + /* Reset the PCI FIFO of the async Tx queue */ + sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), + BMU_RST_SET | BMU_FIFO_RST); + + /* Reset the Tx prefetch units */ + sky2_write32(hw, Y2_QADDR(txqaddr[port], PREF_UNIT_CTRL), + PREF_UNIT_RST_SET); + + sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL), RB_RST_SET); + + sky2_rx_stop(sky2); + + sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET); + sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_SET); + + sky2_phy_power_down(hw, port); + + /* turn off LED's */ + sky2_write16(hw, B0_Y2LED, LED_STAT_OFF); + + sky2_tx_clean(dev); + sky2_rx_clean(sky2); + + sky2_free_rings(sky2); + + return; +} + +static u16 sky2_phy_speed(const struct sky2_hw *hw, u16 aux) +{ + if (hw->flags & SKY2_HW_FIBRE_PHY) + return SPEED_1000; + + if (!(hw->flags & SKY2_HW_GIGABIT)) { + if (aux & PHY_M_PS_SPEED_100) + return SPEED_100; + else + return SPEED_10; + } + + switch (aux & PHY_M_PS_SPEED_MSK) { + case PHY_M_PS_SPEED_1000: + return SPEED_1000; + case PHY_M_PS_SPEED_100: + return SPEED_100; + default: + return SPEED_10; + } +} + +static void sky2_link_up(struct sky2_port *sky2) +{ + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + u16 reg; + static const char *fc_name[] = { + [FC_NONE] = "none", + [FC_TX] = "tx", + [FC_RX] = "rx", + [FC_BOTH] = "both", + }; + + /* enable Rx/Tx */ + reg = gma_read16(hw, port, GM_GP_CTRL); + reg |= GM_GPCR_RX_ENA | GM_GPCR_TX_ENA; + gma_write16(hw, port, GM_GP_CTRL, reg); + + gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK); + + netdev_link_up(sky2->netdev); + + /* Turn on link LED */ + sky2_write8(hw, SK_REG(port, LNK_LED_REG), + LINKLED_ON | LINKLED_BLINK_OFF | LINKLED_LINKSYNC_OFF); + + DBG(PFX "%s: Link is up at %d Mbps, %s duplex, flow control %s\n", + sky2->netdev->name, sky2->speed, + sky2->duplex == DUPLEX_FULL ? "full" : "half", + fc_name[sky2->flow_status]); +} + +static void sky2_link_down(struct sky2_port *sky2) +{ + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + u16 reg; + + gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0); + + reg = gma_read16(hw, port, GM_GP_CTRL); + reg &= ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA); + gma_write16(hw, port, GM_GP_CTRL, reg); + + netdev_link_down(sky2->netdev); + + /* Turn on link LED */ + sky2_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF); + + DBG(PFX "%s: Link is down.\n", sky2->netdev->name); + + sky2_phy_init(hw, port); +} + +static int sky2_autoneg_done(struct sky2_port *sky2, u16 aux) +{ + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + u16 advert, lpa; + + advert = gm_phy_read(hw, port, PHY_MARV_AUNE_ADV); + lpa = gm_phy_read(hw, port, PHY_MARV_AUNE_LP); + if (lpa & PHY_M_AN_RF) { + DBG(PFX "%s: remote fault\n", sky2->netdev->name); + return -1; + } + + if (!(aux & PHY_M_PS_SPDUP_RES)) { + DBG(PFX "%s: speed/duplex mismatch\n", sky2->netdev->name); + return -1; + } + + sky2->speed = sky2_phy_speed(hw, aux); + sky2->duplex = (aux & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF; + + /* Since the pause result bits seem to in different positions on + * different chips. look at registers. + */ + + sky2->flow_status = FC_NONE; + if (advert & ADVERTISE_PAUSE_CAP) { + if (lpa & LPA_PAUSE_CAP) + sky2->flow_status = FC_BOTH; + else if (advert & ADVERTISE_PAUSE_ASYM) + sky2->flow_status = FC_RX; + } else if (advert & ADVERTISE_PAUSE_ASYM) { + if ((lpa & LPA_PAUSE_CAP) && (lpa & LPA_PAUSE_ASYM)) + sky2->flow_status = FC_TX; + } + + if (sky2->duplex == DUPLEX_HALF && sky2->speed < SPEED_1000 + && !(hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX)) + sky2->flow_status = FC_NONE; + + if (sky2->flow_status & FC_TX) + sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON); + else + sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF); + + return 0; +} + +/* Interrupt from PHY */ +static void sky2_phy_intr(struct sky2_hw *hw, unsigned port) +{ + struct net_device *dev = hw->dev[port]; + struct sky2_port *sky2 = netdev_priv(dev); + u16 istatus, phystat; + + istatus = gm_phy_read(hw, port, PHY_MARV_INT_STAT); + phystat = gm_phy_read(hw, port, PHY_MARV_PHY_STAT); + + DBGIO(PFX "%s: phy interrupt status 0x%x 0x%x\n", + sky2->netdev->name, istatus, phystat); + + if (sky2->autoneg == AUTONEG_ENABLE && (istatus & PHY_M_IS_AN_COMPL)) { + if (sky2_autoneg_done(sky2, phystat) == 0) + sky2_link_up(sky2); + return; + } + + if (istatus & PHY_M_IS_LSP_CHANGE) + sky2->speed = sky2_phy_speed(hw, phystat); + + if (istatus & PHY_M_IS_DUP_CHANGE) + sky2->duplex = + (phystat & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF; + + if (istatus & PHY_M_IS_LST_CHANGE) { + if (phystat & PHY_M_PS_LINK_UP) + sky2_link_up(sky2); + else + sky2_link_down(sky2); + } +} + +/* Normal packet - take iob from ring element and put in a new one */ +static struct io_buffer *receive_new(struct sky2_port *sky2, + struct rx_ring_info *re, + unsigned int length) +{ + struct io_buffer *iob, *niob; + unsigned hdr_space = sky2->rx_data_size; + + /* Don't be tricky about reusing pages (yet) */ + niob = sky2_rx_alloc(sky2); + if (!niob) + return NULL; + + iob = re->iob; + + re->iob = niob; + sky2_rx_map_iob(sky2->hw->pdev, re, hdr_space); + + iob_put(iob, length); + return iob; +} + +/* + * Receive one packet. + * For larger packets, get new buffer. + */ +static struct io_buffer *sky2_receive(struct net_device *dev, + u16 length, u32 status) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct rx_ring_info *re = sky2->rx_ring + sky2->rx_next; + struct io_buffer *iob = NULL; + u16 count = (status & GMR_FS_LEN) >> 16; + + DBGIO(PFX "%s: rx slot %d status 0x%x len %d\n", + dev->name, sky2->rx_next, status, length); + + sky2->rx_next = (sky2->rx_next + 1) % RX_PENDING; + + /* This chip has hardware problems that generates bogus status. + * So do only marginal checking and expect higher level protocols + * to handle crap frames. + */ + if (sky2->hw->chip_id == CHIP_ID_YUKON_FE_P && + sky2->hw->chip_rev == CHIP_REV_YU_FE2_A0 && + length == count) + goto okay; + + if (status & GMR_FS_ANY_ERR) + goto error; + + if (!(status & GMR_FS_RX_OK)) + goto resubmit; + + /* if length reported by DMA does not match PHY, packet was truncated */ + if (length != count) + goto len_error; + +okay: + iob = receive_new(sky2, re, length); +resubmit: + sky2_rx_submit(sky2, re); + + return iob; + +len_error: + /* Truncation of overlength packets + causes PHY length to not match MAC length */ + DBG2(PFX "%s: rx length error: status %#x length %d\n", + dev->name, status, length); + + /* Pass NULL as iob because we want to keep our iob in the + ring for the next packet. */ + netdev_rx_err(dev, NULL, -EINVAL); + goto resubmit; + +error: + if (status & GMR_FS_RX_FF_OV) { + DBG2(PFX "%s: FIFO overflow error\n", dev->name); + netdev_rx_err(dev, NULL, -EBUSY); + goto resubmit; + } + + DBG2(PFX "%s: rx error, status 0x%x length %d\n", + dev->name, status, length); + netdev_rx_err(dev, NULL, -EIO); + + goto resubmit; +} + +/* Transmit complete */ +static inline void sky2_tx_done(struct net_device *dev, u16 last) +{ + struct sky2_port *sky2 = netdev_priv(dev); + + sky2_tx_complete(sky2, last); +} + +/* Process status response ring */ +static void sky2_status_intr(struct sky2_hw *hw, u16 idx) +{ + unsigned rx[2] = { 0, 0 }; + + rmb(); + do { + struct sky2_port *sky2; + struct sky2_status_le *le = hw->st_le + hw->st_idx; + unsigned port; + struct net_device *dev; + struct io_buffer *iob; + u32 status; + u16 length; + u8 opcode = le->opcode; + + if (!(opcode & HW_OWNER)) + break; + + port = le->css & CSS_LINK_BIT; + dev = hw->dev[port]; + sky2 = netdev_priv(dev); + length = le16_to_cpu(le->length); + status = le32_to_cpu(le->status); + + hw->st_idx = RING_NEXT(hw->st_idx, STATUS_RING_SIZE); + + le->opcode = 0; + switch (opcode & ~HW_OWNER) { + case OP_RXSTAT: + ++rx[port]; + iob = sky2_receive(dev, length, status); + if (!iob) { + netdev_rx_err(dev, NULL, -ENOMEM); + break; + } + + netdev_rx(dev, iob); + break; + + case OP_RXCHKS: + DBG2(PFX "status OP_RXCHKS but checksum offloading disabled\n"); + break; + + case OP_TXINDEXLE: + /* TX index reports status for both ports */ + assert(TX_RING_SIZE <= 0x1000); + sky2_tx_done(hw->dev[0], status & 0xfff); + if (hw->dev[1]) + sky2_tx_done(hw->dev[1], + ((status >> 24) & 0xff) + | (u16)(length & 0xf) << 8); + break; + + default: + DBG(PFX "unknown status opcode 0x%x\n", opcode); + } + } while (hw->st_idx != idx); + + /* Fully processed status ring so clear irq */ + sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ); + + if (rx[0]) + sky2_rx_update(netdev_priv(hw->dev[0]), Q_R1); + + if (rx[1]) + sky2_rx_update(netdev_priv(hw->dev[1]), Q_R2); +} + +static void sky2_hw_error(struct sky2_hw *hw, unsigned port, u32 status) +{ + struct net_device *dev = hw->dev[port]; + + DBGIO(PFX "%s: hw error interrupt status 0x%x\n", dev->name, status); + + if (status & Y2_IS_PAR_RD1) { + DBG(PFX "%s: ram data read parity error\n", dev->name); + /* Clear IRQ */ + sky2_write16(hw, RAM_BUFFER(port, B3_RI_CTRL), RI_CLR_RD_PERR); + } + + if (status & Y2_IS_PAR_WR1) { + DBG(PFX "%s: ram data write parity error\n", dev->name); + sky2_write16(hw, RAM_BUFFER(port, B3_RI_CTRL), RI_CLR_WR_PERR); + } + + if (status & Y2_IS_PAR_MAC1) { + DBG(PFX "%s: MAC parity error\n", dev->name); + sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_PE); + } + + if (status & Y2_IS_PAR_RX1) { + DBG(PFX "%s: RX parity error\n", dev->name); + sky2_write32(hw, Q_ADDR(rxqaddr[port], Q_CSR), BMU_CLR_IRQ_PAR); + } + + if (status & Y2_IS_TCP_TXA1) { + DBG(PFX "%s: TCP segmentation error\n", dev->name); + sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_CLR_IRQ_TCP); + } +} + +static void sky2_hw_intr(struct sky2_hw *hw) +{ + u32 status = sky2_read32(hw, B0_HWE_ISRC); + u32 hwmsk = sky2_read32(hw, B0_HWE_IMSK); + + status &= hwmsk; + + if (status & Y2_IS_TIST_OV) + sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ); + + if (status & (Y2_IS_MST_ERR | Y2_IS_IRQ_STAT)) { + u16 pci_err; + + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); + pci_err = sky2_pci_read16(hw, PCI_STATUS); + DBG(PFX "PCI hardware error (0x%x)\n", pci_err); + + sky2_pci_write16(hw, PCI_STATUS, + pci_err | PCI_STATUS_ERROR_BITS); + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); + } + + if (status & Y2_IS_PCI_EXP) { + /* PCI-Express uncorrectable Error occurred */ + u32 err; + + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); + err = sky2_read32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS); + sky2_write32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS, + 0xfffffffful); + DBG(PFX "PCI-Express error (0x%x)\n", err); + + sky2_read32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS); + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); + } + + if (status & Y2_HWE_L1_MASK) + sky2_hw_error(hw, 0, status); + status >>= 8; + if (status & Y2_HWE_L1_MASK) + sky2_hw_error(hw, 1, status); +} + +static void sky2_mac_intr(struct sky2_hw *hw, unsigned port) +{ + struct net_device *dev = hw->dev[port]; + u8 status = sky2_read8(hw, SK_REG(port, GMAC_IRQ_SRC)); + + DBGIO(PFX "%s: mac interrupt status 0x%x\n", dev->name, status); + + if (status & GM_IS_RX_CO_OV) + gma_read16(hw, port, GM_RX_IRQ_SRC); + + if (status & GM_IS_TX_CO_OV) + gma_read16(hw, port, GM_TX_IRQ_SRC); + + if (status & GM_IS_RX_FF_OR) { + sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_CLI_RX_FO); + } + + if (status & GM_IS_TX_FF_UR) { + sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_FU); + } +} + +/* This should never happen it is a bug. */ +static void sky2_le_error(struct sky2_hw *hw, unsigned port, + u16 q, unsigned ring_size __unused) +{ + struct net_device *dev = hw->dev[port]; + struct sky2_port *sky2 = netdev_priv(dev); + int idx; + const u64 *le = (q == Q_R1 || q == Q_R2) + ? (u64 *) sky2->rx_le : (u64 *) sky2->tx_le; + + idx = sky2_read16(hw, Y2_QADDR(q, PREF_UNIT_GET_IDX)); + DBG(PFX "%s: descriptor error q=%#x get=%d [%llx] last=%d put=%d should be %d\n", + dev->name, (unsigned) q, idx, (unsigned long long) le[idx], + (int) sky2_read16(hw, Y2_QADDR(q, PREF_UNIT_LAST_IDX)), + (int) sky2_read16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX)), + le == (u64 *)sky2->rx_le? sky2->rx_put : sky2->tx_prod); + + sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_CLR_IRQ_CHK); +} + +/* Hardware/software error handling */ +static void sky2_err_intr(struct sky2_hw *hw, u32 status) +{ + DBG(PFX "error interrupt status=%#x\n", status); + + if (status & Y2_IS_HW_ERR) + sky2_hw_intr(hw); + + if (status & Y2_IS_IRQ_MAC1) + sky2_mac_intr(hw, 0); + + if (status & Y2_IS_IRQ_MAC2) + sky2_mac_intr(hw, 1); + + if (status & Y2_IS_CHK_RX1) + sky2_le_error(hw, 0, Q_R1, RX_LE_SIZE); + + if (status & Y2_IS_CHK_RX2) + sky2_le_error(hw, 1, Q_R2, RX_LE_SIZE); + + if (status & Y2_IS_CHK_TXA1) + sky2_le_error(hw, 0, Q_XA1, TX_RING_SIZE); + + if (status & Y2_IS_CHK_TXA2) + sky2_le_error(hw, 1, Q_XA2, TX_RING_SIZE); +} + +static void sky2_poll(struct net_device *dev) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + u32 status = sky2_read32(hw, B0_Y2_SP_EISR); + u16 idx; + + if (status & Y2_IS_ERROR) + sky2_err_intr(hw, status); + + if (status & Y2_IS_IRQ_PHY1) + sky2_phy_intr(hw, 0); + + if (status & Y2_IS_IRQ_PHY2) + sky2_phy_intr(hw, 1); + + while ((idx = sky2_read16(hw, STAT_PUT_IDX)) != hw->st_idx) { + sky2_status_intr(hw, idx); + } + + /* Bug/Errata workaround? + * Need to kick the TX irq moderation timer. + */ + if (sky2_read8(hw, STAT_TX_TIMER_CTRL) == TIM_START) { + sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP); + sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START); + } + sky2_read32(hw, B0_Y2_SP_LISR); +} + +/* Chip internal frequency for clock calculations */ +static u32 sky2_mhz(const struct sky2_hw *hw) +{ + switch (hw->chip_id) { + case CHIP_ID_YUKON_EC: + case CHIP_ID_YUKON_EC_U: + case CHIP_ID_YUKON_EX: + case CHIP_ID_YUKON_SUPR: + case CHIP_ID_YUKON_UL_2: + return 125; + + case CHIP_ID_YUKON_FE: + return 100; + + case CHIP_ID_YUKON_FE_P: + return 50; + + case CHIP_ID_YUKON_XL: + return 156; + + default: + DBG(PFX "unknown chip ID!\n"); + return 100; /* bogus */ + } +} + +static inline u32 sky2_us2clk(const struct sky2_hw *hw, u32 us) +{ + return sky2_mhz(hw) * us; +} + +static inline u32 sky2_clk2us(const struct sky2_hw *hw, u32 clk) +{ + return clk / sky2_mhz(hw); +} + +static int sky2_init(struct sky2_hw *hw) +{ + u8 t8; + + /* Enable all clocks and check for bad PCI access */ + sky2_pci_write32(hw, PCI_DEV_REG3, 0); + + sky2_write8(hw, B0_CTST, CS_RST_CLR); + + hw->chip_id = sky2_read8(hw, B2_CHIP_ID); + hw->chip_rev = (sky2_read8(hw, B2_MAC_CFG) & CFG_CHIP_R_MSK) >> 4; + + switch(hw->chip_id) { + case CHIP_ID_YUKON_XL: + hw->flags = SKY2_HW_GIGABIT | SKY2_HW_NEWER_PHY; + break; + + case CHIP_ID_YUKON_EC_U: + hw->flags = SKY2_HW_GIGABIT + | SKY2_HW_NEWER_PHY + | SKY2_HW_ADV_POWER_CTL; + break; + + case CHIP_ID_YUKON_EX: + hw->flags = SKY2_HW_GIGABIT + | SKY2_HW_NEWER_PHY + | SKY2_HW_NEW_LE + | SKY2_HW_ADV_POWER_CTL; + break; + + case CHIP_ID_YUKON_EC: + /* This rev is really old, and requires untested workarounds */ + if (hw->chip_rev == CHIP_REV_YU_EC_A1) { + DBG(PFX "unsupported revision Yukon-EC rev A1\n"); + return -EOPNOTSUPP; + } + hw->flags = SKY2_HW_GIGABIT; + break; + + case CHIP_ID_YUKON_FE: + break; + + case CHIP_ID_YUKON_FE_P: + hw->flags = SKY2_HW_NEWER_PHY + | SKY2_HW_NEW_LE + | SKY2_HW_AUTO_TX_SUM + | SKY2_HW_ADV_POWER_CTL; + break; + + case CHIP_ID_YUKON_SUPR: + hw->flags = SKY2_HW_GIGABIT + | SKY2_HW_NEWER_PHY + | SKY2_HW_NEW_LE + | SKY2_HW_AUTO_TX_SUM + | SKY2_HW_ADV_POWER_CTL; + break; + + case CHIP_ID_YUKON_UL_2: + hw->flags = SKY2_HW_GIGABIT + | SKY2_HW_ADV_POWER_CTL; + break; + + default: + DBG(PFX "unsupported chip type 0x%x\n", hw->chip_id); + return -EOPNOTSUPP; + } + + hw->pmd_type = sky2_read8(hw, B2_PMD_TYP); + if (hw->pmd_type == 'L' || hw->pmd_type == 'S' || hw->pmd_type == 'P') + hw->flags |= SKY2_HW_FIBRE_PHY; + + hw->ports = 1; + t8 = sky2_read8(hw, B2_Y2_HW_RES); + if ((t8 & CFG_DUAL_MAC_MSK) == CFG_DUAL_MAC_MSK) { + if (!(sky2_read8(hw, B2_Y2_CLK_GATE) & Y2_STATUS_LNK2_INAC)) + ++hw->ports; + } + + return 0; +} + +static void sky2_reset(struct sky2_hw *hw) +{ + u16 status; + int i, cap; + u32 hwe_mask = Y2_HWE_ALL_MASK; + + /* disable ASF */ + if (hw->chip_id == CHIP_ID_YUKON_EX) { + status = sky2_read16(hw, HCU_CCSR); + status &= ~(HCU_CCSR_AHB_RST | HCU_CCSR_CPU_RST_MODE | + HCU_CCSR_UC_STATE_MSK); + sky2_write16(hw, HCU_CCSR, status); + } else + sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET); + sky2_write16(hw, B0_CTST, Y2_ASF_DISABLE); + + /* do a SW reset */ + sky2_write8(hw, B0_CTST, CS_RST_SET); + sky2_write8(hw, B0_CTST, CS_RST_CLR); + + /* allow writes to PCI config */ + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); + + /* clear PCI errors, if any */ + status = sky2_pci_read16(hw, PCI_STATUS); + status |= PCI_STATUS_ERROR_BITS; + sky2_pci_write16(hw, PCI_STATUS, status); + + sky2_write8(hw, B0_CTST, CS_MRST_CLR); + + cap = pci_find_capability(hw->pdev, PCI_CAP_ID_EXP); + if (cap) { + sky2_write32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS, + 0xfffffffful); + + /* If an error bit is stuck on ignore it */ + if (sky2_read32(hw, B0_HWE_ISRC) & Y2_IS_PCI_EXP) + DBG(PFX "ignoring stuck error report bit\n"); + else + hwe_mask |= Y2_IS_PCI_EXP; + } + + sky2_power_on(hw); + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); + + for (i = 0; i < hw->ports; i++) { + sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_SET); + sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_CLR); + + if (hw->chip_id == CHIP_ID_YUKON_EX || + hw->chip_id == CHIP_ID_YUKON_SUPR) + sky2_write16(hw, SK_REG(i, GMAC_CTRL), + GMC_BYP_MACSECRX_ON | GMC_BYP_MACSECTX_ON + | GMC_BYP_RETR_ON); + } + + /* Clear I2C IRQ noise */ + sky2_write32(hw, B2_I2C_IRQ, 1); + + /* turn off hardware timer (unused) */ + sky2_write8(hw, B2_TI_CTRL, TIM_STOP); + sky2_write8(hw, B2_TI_CTRL, TIM_CLR_IRQ); + + sky2_write8(hw, B0_Y2LED, LED_STAT_ON); + + /* Turn off descriptor polling */ + sky2_write32(hw, B28_DPT_CTRL, DPT_STOP); + + /* Turn off receive timestamp */ + sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_STOP); + sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ); + + /* enable the Tx Arbiters */ + for (i = 0; i < hw->ports; i++) + sky2_write8(hw, SK_REG(i, TXA_CTRL), TXA_ENA_ARB); + + /* Initialize ram interface */ + for (i = 0; i < hw->ports; i++) { + sky2_write8(hw, RAM_BUFFER(i, B3_RI_CTRL), RI_RST_CLR); + + sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_R1), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XA1), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XS1), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_R1), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XA1), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XS1), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_R2), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XA2), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XS2), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_R2), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XA2), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XS2), SK_RI_TO_53); + } + + sky2_write32(hw, B0_HWE_IMSK, hwe_mask); + + for (i = 0; i < hw->ports; i++) + sky2_gmac_reset(hw, i); + + memset(hw->st_le, 0, STATUS_LE_BYTES); + hw->st_idx = 0; + + sky2_write32(hw, STAT_CTRL, SC_STAT_RST_SET); + sky2_write32(hw, STAT_CTRL, SC_STAT_RST_CLR); + + sky2_write32(hw, STAT_LIST_ADDR_LO, hw->st_dma); + sky2_write32(hw, STAT_LIST_ADDR_HI, (u64) hw->st_dma >> 32); + + /* Set the list last index */ + sky2_write16(hw, STAT_LAST_IDX, STATUS_RING_SIZE - 1); + + sky2_write16(hw, STAT_TX_IDX_TH, 10); + sky2_write8(hw, STAT_FIFO_WM, 16); + + /* set Status-FIFO ISR watermark */ + if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0) + sky2_write8(hw, STAT_FIFO_ISR_WM, 4); + else + sky2_write8(hw, STAT_FIFO_ISR_WM, 16); + + sky2_write32(hw, STAT_TX_TIMER_INI, sky2_us2clk(hw, 1000)); + sky2_write32(hw, STAT_ISR_TIMER_INI, sky2_us2clk(hw, 20)); + sky2_write32(hw, STAT_LEV_TIMER_INI, sky2_us2clk(hw, 100)); + + /* enable status unit */ + sky2_write32(hw, STAT_CTRL, SC_STAT_OP_ON); + + sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START); + sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_START); + sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START); +} + +static u32 sky2_supported_modes(const struct sky2_hw *hw) +{ + if (sky2_is_copper(hw)) { + u32 modes = SUPPORTED_10baseT_Half + | SUPPORTED_10baseT_Full + | SUPPORTED_100baseT_Half + | SUPPORTED_100baseT_Full + | SUPPORTED_Autoneg | SUPPORTED_TP; + + if (hw->flags & SKY2_HW_GIGABIT) + modes |= SUPPORTED_1000baseT_Half + | SUPPORTED_1000baseT_Full; + return modes; + } else + return SUPPORTED_1000baseT_Half + | SUPPORTED_1000baseT_Full + | SUPPORTED_Autoneg + | SUPPORTED_FIBRE; +} + +static void sky2_set_multicast(struct net_device *dev) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + u16 reg; + u8 filter[8]; + int rx_pause; + + rx_pause = (sky2->flow_status == FC_RX || sky2->flow_status == FC_BOTH); + + reg = gma_read16(hw, port, GM_RX_CTRL); + reg |= GM_RXCR_UCF_ENA; + + memset(filter, 0xff, sizeof(filter)); + + gma_write16(hw, port, GM_MC_ADDR_H1, + (u16) filter[0] | ((u16) filter[1] << 8)); + gma_write16(hw, port, GM_MC_ADDR_H2, + (u16) filter[2] | ((u16) filter[3] << 8)); + gma_write16(hw, port, GM_MC_ADDR_H3, + (u16) filter[4] | ((u16) filter[5] << 8)); + gma_write16(hw, port, GM_MC_ADDR_H4, + (u16) filter[6] | ((u16) filter[7] << 8)); + + gma_write16(hw, port, GM_RX_CTRL, reg); +} + +/* Initialize network device */ +static struct net_device *sky2_init_netdev(struct sky2_hw *hw, + unsigned port) +{ + struct sky2_port *sky2; + struct net_device *dev = alloc_etherdev(sizeof(*sky2)); + + if (!dev) { + DBG(PFX "etherdev alloc failed\n"); + return NULL; + } + + dev->dev = &hw->pdev->dev; + + sky2 = netdev_priv(dev); + sky2->netdev = dev; + sky2->hw = hw; + + /* Auto speed and flow control */ + sky2->autoneg = AUTONEG_ENABLE; + sky2->flow_mode = FC_BOTH; + + sky2->duplex = -1; + sky2->speed = -1; + sky2->advertising = sky2_supported_modes(hw); + + hw->dev[port] = dev; + + sky2->port = port; + + /* read the mac address */ + memcpy(dev->ll_addr, (void *)(hw->regs + B2_MAC_1 + port * 8), ETH_ALEN); + + return dev; +} + +static void sky2_show_addr(struct net_device *dev) +{ + DBG2(PFX "%s: addr %s\n", dev->name, netdev_hwaddr(dev)); +} + +#if DBGLVL_MAX +/* This driver supports yukon2 chipset only */ +static const char *sky2_name(u8 chipid, char *buf, int sz) +{ + const char *name[] = { + "XL", /* 0xb3 */ + "EC Ultra", /* 0xb4 */ + "Extreme", /* 0xb5 */ + "EC", /* 0xb6 */ + "FE", /* 0xb7 */ + "FE+", /* 0xb8 */ + "Supreme", /* 0xb9 */ + "UL 2", /* 0xba */ + }; + + if (chipid >= CHIP_ID_YUKON_XL && chipid <= CHIP_ID_YUKON_UL_2) + strncpy(buf, name[chipid - CHIP_ID_YUKON_XL], sz); + else + snprintf(buf, sz, "(chip %#x)", chipid); + return buf; +} +#endif + +static void sky2_net_irq(struct net_device *dev, int enable) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + + u32 imask = sky2_read32(hw, B0_IMSK); + if (enable) + imask |= portirq_msk[sky2->port]; + else + imask &= ~portirq_msk[sky2->port]; + sky2_write32(hw, B0_IMSK, imask); +} + +static struct net_device_operations sky2_operations = { + .open = sky2_up, + .close = sky2_down, + .transmit = sky2_xmit_frame, + .poll = sky2_poll, + .irq = sky2_net_irq +}; + +static int sky2_probe(struct pci_device *pdev, + const struct pci_device_id *ent __unused) +{ + struct net_device *dev; + struct sky2_hw *hw; + int err; + char buf1[16] __unused; /* only for debugging */ + + adjust_pci_device(pdev); + + err = -ENOMEM; + hw = zalloc(sizeof(*hw)); + if (!hw) { + DBG(PFX "cannot allocate hardware struct\n"); + goto err_out; + } + + hw->pdev = pdev; + + hw->regs = (unsigned long)ioremap(pci_bar_start(pdev, PCI_BASE_ADDRESS_0), 0x4000); + if (!hw->regs) { + DBG(PFX "cannot map device registers\n"); + goto err_out_free_hw; + } + + /* ring for status responses */ + hw->st_le = malloc_dma(STATUS_LE_BYTES, STATUS_RING_ALIGN); + if (!hw->st_le) + goto err_out_iounmap; + hw->st_dma = virt_to_bus(hw->st_le); + memset(hw->st_le, 0, STATUS_LE_BYTES); + + err = sky2_init(hw); + if (err) + goto err_out_iounmap; + +#if DBGLVL_MAX + DBG2(PFX "Yukon-2 %s chip revision %d\n", + sky2_name(hw->chip_id, buf1, sizeof(buf1)), hw->chip_rev); +#endif + + sky2_reset(hw); + + dev = sky2_init_netdev(hw, 0); + if (!dev) { + err = -ENOMEM; + goto err_out_free_pci; + } + + netdev_init(dev, &sky2_operations); + + err = register_netdev(dev); + if (err) { + DBG(PFX "cannot register net device\n"); + goto err_out_free_netdev; + } + + sky2_write32(hw, B0_IMSK, Y2_IS_BASE); + + sky2_show_addr(dev); + + if (hw->ports > 1) { + struct net_device *dev1; + + dev1 = sky2_init_netdev(hw, 1); + if (!dev1) + DBG(PFX "allocation for second device failed\n"); + else if ((err = register_netdev(dev1))) { + DBG(PFX "register of second port failed (%d)\n", err); + hw->dev[1] = NULL; + netdev_nullify(dev1); + netdev_put(dev1); + } else + sky2_show_addr(dev1); + } + + pci_set_drvdata(pdev, dev); + + return 0; + +err_out_free_netdev: + netdev_nullify(dev); + netdev_put(dev); +err_out_free_pci: + sky2_write8(hw, B0_CTST, CS_RST_SET); + free_dma(hw->st_le, STATUS_LE_BYTES); +err_out_iounmap: + iounmap((void *)hw->regs); +err_out_free_hw: + free(hw); +err_out: + pci_set_drvdata(pdev, NULL); + return err; +} + +static void sky2_remove(struct pci_device *pdev) +{ + struct sky2_hw *hw = pci_get_drvdata(pdev); + int i; + + if (!hw) + return; + + for (i = hw->ports-1; i >= 0; --i) + unregister_netdev(hw->dev[i]); + + sky2_write32(hw, B0_IMSK, 0); + + sky2_power_aux(hw); + + sky2_write16(hw, B0_Y2LED, LED_STAT_OFF); + sky2_write8(hw, B0_CTST, CS_RST_SET); + sky2_read8(hw, B0_CTST); + + free_dma(hw->st_le, STATUS_LE_BYTES); + + for (i = hw->ports-1; i >= 0; --i) { + netdev_nullify(hw->dev[i]); + netdev_put(hw->dev[i]); + } + + iounmap((void *)hw->regs); + free(hw); + + pci_set_drvdata(pdev, NULL); +} + +struct pci_driver sky2_driver __pci_driver = { + .ids = sky2_id_table, + .id_count = (sizeof (sky2_id_table) / sizeof (sky2_id_table[0])), + .probe = sky2_probe, + .remove = sky2_remove +}; diff --git a/src/drivers/net/sky2.h b/src/drivers/net/sky2.h new file mode 100644 index 00000000..7963fbe7 --- /dev/null +++ b/src/drivers/net/sky2.h @@ -0,0 +1,2176 @@ +/* + * Definitions for the new Marvell Yukon 2 driver. + */ +#ifndef _SKY2_H +#define _SKY2_H + +FILE_LICENCE ( GPL2_ONLY ); + +/* Added for gPXE ------------------ */ + +/* These were defined in Linux ethtool.h. Their values are arbitrary; + they aid only in bookkeeping for the driver. */ + +#define AUTONEG_DISABLE 0x00 +#define AUTONEG_ENABLE 0x01 + +#define DUPLEX_HALF 0x00 +#define DUPLEX_FULL 0x01 + +#define SPEED_10 10 +#define SPEED_100 100 +#define SPEED_1000 1000 + +#define ADVERTISED_10baseT_Half (1 << 0) +#define ADVERTISED_10baseT_Full (1 << 1) +#define ADVERTISED_100baseT_Half (1 << 2) +#define ADVERTISED_100baseT_Full (1 << 3) +#define ADVERTISED_1000baseT_Half (1 << 4) +#define ADVERTISED_1000baseT_Full (1 << 5) + +#define SUPPORTED_10baseT_Half (1 << 0) +#define SUPPORTED_10baseT_Full (1 << 1) +#define SUPPORTED_100baseT_Half (1 << 2) +#define SUPPORTED_100baseT_Full (1 << 3) +#define SUPPORTED_1000baseT_Half (1 << 4) +#define SUPPORTED_1000baseT_Full (1 << 5) +#define SUPPORTED_Autoneg (1 << 6) +#define SUPPORTED_TP (1 << 7) +#define SUPPORTED_FIBRE (1 << 10) + +/* ----------------------------------- */ + +/* PCI config registers */ +enum { + PCI_DEV_REG1 = 0x40, + PCI_DEV_REG2 = 0x44, + PCI_DEV_STATUS = 0x7c, + PCI_DEV_REG3 = 0x80, + PCI_DEV_REG4 = 0x84, + PCI_DEV_REG5 = 0x88, + PCI_CFG_REG_0 = 0x90, + PCI_CFG_REG_1 = 0x94, +}; + +/* Yukon-2 */ +enum pci_dev_reg_1 { + PCI_Y2_PIG_ENA = 1<<31, /* Enable Plug-in-Go (YUKON-2) */ + PCI_Y2_DLL_DIS = 1<<30, /* Disable PCI DLL (YUKON-2) */ + PCI_SW_PWR_ON_RST= 1<<30, /* SW Power on Reset (Yukon-EX) */ + PCI_Y2_PHY2_COMA = 1<<29, /* Set PHY 2 to Coma Mode (YUKON-2) */ + PCI_Y2_PHY1_COMA = 1<<28, /* Set PHY 1 to Coma Mode (YUKON-2) */ + PCI_Y2_PHY2_POWD = 1<<27, /* Set PHY 2 to Power Down (YUKON-2) */ + PCI_Y2_PHY1_POWD = 1<<26, /* Set PHY 1 to Power Down (YUKON-2) */ + PCI_Y2_PME_LEGACY= 1<<15, /* PCI Express legacy power management mode */ + + PCI_PHY_LNK_TIM_MSK= 3L<<8,/* Bit 9.. 8: GPHY Link Trigger Timer */ + PCI_ENA_L1_EVENT = 1<<7, /* Enable PEX L1 Event */ + PCI_ENA_GPHY_LNK = 1<<6, /* Enable PEX L1 on GPHY Link down */ + PCI_FORCE_PEX_L1 = 1<<5, /* Force to PEX L1 */ +}; + +enum pci_dev_reg_2 { + PCI_VPD_WR_THR = 0xffL<<24, /* Bit 31..24: VPD Write Threshold */ + PCI_DEV_SEL = 0x7fL<<17, /* Bit 23..17: EEPROM Device Select */ + PCI_VPD_ROM_SZ = 7L<<14, /* Bit 16..14: VPD ROM Size */ + + PCI_PATCH_DIR = 0xfL<<8, /* Bit 11.. 8: Ext Patches dir 3..0 */ + PCI_EXT_PATCHS = 0xfL<<4, /* Bit 7.. 4: Extended Patches 3..0 */ + PCI_EN_DUMMY_RD = 1<<3, /* Enable Dummy Read */ + PCI_REV_DESC = 1<<2, /* Reverse Desc. Bytes */ + + PCI_USEDATA64 = 1<<0, /* Use 64Bit Data bus ext */ +}; + +/* PCI_OUR_REG_4 32 bit Our Register 4 (Yukon-ECU only) */ +enum pci_dev_reg_4 { + /* (Link Training & Status State Machine) */ + P_PEX_LTSSM_STAT_MSK = 0x7fL<<25, /* Bit 31..25: PEX LTSSM Mask */ +#define P_PEX_LTSSM_STAT(x) ((x << 25) & P_PEX_LTSSM_STAT_MSK) + P_PEX_LTSSM_L1_STAT = 0x34, + P_PEX_LTSSM_DET_STAT = 0x01, + P_TIMER_VALUE_MSK = 0xffL<<16, /* Bit 23..16: Timer Value Mask */ + /* (Active State Power Management) */ + P_FORCE_ASPM_REQUEST = 1<<15, /* Force ASPM Request (A1 only) */ + P_ASPM_GPHY_LINK_DOWN = 1<<14, /* GPHY Link Down (A1 only) */ + P_ASPM_INT_FIFO_EMPTY = 1<<13, /* Internal FIFO Empty (A1 only) */ + P_ASPM_CLKRUN_REQUEST = 1<<12, /* CLKRUN Request (A1 only) */ + + P_ASPM_FORCE_CLKREQ_ENA = 1<<4, /* Force CLKREQ Enable (A1b only) */ + P_ASPM_CLKREQ_PAD_CTL = 1<<3, /* CLKREQ PAD Control (A1 only) */ + P_ASPM_A1_MODE_SELECT = 1<<2, /* A1 Mode Select (A1 only) */ + P_CLK_GATE_PEX_UNIT_ENA = 1<<1, /* Enable Gate PEX Unit Clock */ + P_CLK_GATE_ROOT_COR_ENA = 1<<0, /* Enable Gate Root Core Clock */ + P_ASPM_CONTROL_MSK = P_FORCE_ASPM_REQUEST | P_ASPM_GPHY_LINK_DOWN + | P_ASPM_CLKRUN_REQUEST | P_ASPM_INT_FIFO_EMPTY, +}; + +/* PCI_OUR_REG_5 32 bit Our Register 5 (Yukon-ECU only) */ +enum pci_dev_reg_5 { + /* Bit 31..27: for A3 & later */ + P_CTL_DIV_CORE_CLK_ENA = 1<<31, /* Divide Core Clock Enable */ + P_CTL_SRESET_VMAIN_AV = 1<<30, /* Soft Reset for Vmain_av De-Glitch */ + P_CTL_BYPASS_VMAIN_AV = 1<<29, /* Bypass En. for Vmain_av De-Glitch */ + P_CTL_TIM_VMAIN_AV_MSK = 3<<27, /* Bit 28..27: Timer Vmain_av Mask */ + /* Bit 26..16: Release Clock on Event */ + P_REL_PCIE_RST_DE_ASS = 1<<26, /* PCIe Reset De-Asserted */ + P_REL_GPHY_REC_PACKET = 1<<25, /* GPHY Received Packet */ + P_REL_INT_FIFO_N_EMPTY = 1<<24, /* Internal FIFO Not Empty */ + P_REL_MAIN_PWR_AVAIL = 1<<23, /* Main Power Available */ + P_REL_CLKRUN_REQ_REL = 1<<22, /* CLKRUN Request Release */ + P_REL_PCIE_RESET_ASS = 1<<21, /* PCIe Reset Asserted */ + P_REL_PME_ASSERTED = 1<<20, /* PME Asserted */ + P_REL_PCIE_EXIT_L1_ST = 1<<19, /* PCIe Exit L1 State */ + P_REL_LOADER_NOT_FIN = 1<<18, /* EPROM Loader Not Finished */ + P_REL_PCIE_RX_EX_IDLE = 1<<17, /* PCIe Rx Exit Electrical Idle State */ + P_REL_GPHY_LINK_UP = 1<<16, /* GPHY Link Up */ + + /* Bit 10.. 0: Mask for Gate Clock */ + P_GAT_PCIE_RST_ASSERTED = 1<<10,/* PCIe Reset Asserted */ + P_GAT_GPHY_N_REC_PACKET = 1<<9, /* GPHY Not Received Packet */ + P_GAT_INT_FIFO_EMPTY = 1<<8, /* Internal FIFO Empty */ + P_GAT_MAIN_PWR_N_AVAIL = 1<<7, /* Main Power Not Available */ + P_GAT_CLKRUN_REQ_REL = 1<<6, /* CLKRUN Not Requested */ + P_GAT_PCIE_RESET_ASS = 1<<5, /* PCIe Reset Asserted */ + P_GAT_PME_DE_ASSERTED = 1<<4, /* PME De-Asserted */ + P_GAT_PCIE_ENTER_L1_ST = 1<<3, /* PCIe Enter L1 State */ + P_GAT_LOADER_FINISHED = 1<<2, /* EPROM Loader Finished */ + P_GAT_PCIE_RX_EL_IDLE = 1<<1, /* PCIe Rx Electrical Idle State */ + P_GAT_GPHY_LINK_DOWN = 1<<0, /* GPHY Link Down */ + + PCIE_OUR5_EVENT_CLK_D3_SET = P_REL_GPHY_REC_PACKET | + P_REL_INT_FIFO_N_EMPTY | + P_REL_PCIE_EXIT_L1_ST | + P_REL_PCIE_RX_EX_IDLE | + P_GAT_GPHY_N_REC_PACKET | + P_GAT_INT_FIFO_EMPTY | + P_GAT_PCIE_ENTER_L1_ST | + P_GAT_PCIE_RX_EL_IDLE, +}; + +#/* PCI_CFG_REG_1 32 bit Config Register 1 (Yukon-Ext only) */ +enum pci_cfg_reg1 { + P_CF1_DIS_REL_EVT_RST = 1<<24, /* Dis. Rel. Event during PCIE reset */ + /* Bit 23..21: Release Clock on Event */ + P_CF1_REL_LDR_NOT_FIN = 1<<23, /* EEPROM Loader Not Finished */ + P_CF1_REL_VMAIN_AVLBL = 1<<22, /* Vmain available */ + P_CF1_REL_PCIE_RESET = 1<<21, /* PCI-E reset */ + /* Bit 20..18: Gate Clock on Event */ + P_CF1_GAT_LDR_NOT_FIN = 1<<20, /* EEPROM Loader Finished */ + P_CF1_GAT_PCIE_RX_IDLE = 1<<19, /* PCI-E Rx Electrical idle */ + P_CF1_GAT_PCIE_RESET = 1<<18, /* PCI-E Reset */ + P_CF1_PRST_PHY_CLKREQ = 1<<17, /* Enable PCI-E rst & PM2PHY gen. CLKREQ */ + P_CF1_PCIE_RST_CLKREQ = 1<<16, /* Enable PCI-E rst generate CLKREQ */ + + P_CF1_ENA_CFG_LDR_DONE = 1<<8, /* Enable core level Config loader done */ + + P_CF1_ENA_TXBMU_RD_IDLE = 1<<1, /* Enable TX BMU Read IDLE for ASPM */ + P_CF1_ENA_TXBMU_WR_IDLE = 1<<0, /* Enable TX BMU Write IDLE for ASPM */ + + PCIE_CFG1_EVENT_CLK_D3_SET = P_CF1_DIS_REL_EVT_RST | + P_CF1_REL_LDR_NOT_FIN | + P_CF1_REL_VMAIN_AVLBL | + P_CF1_REL_PCIE_RESET | + P_CF1_GAT_LDR_NOT_FIN | + P_CF1_GAT_PCIE_RESET | + P_CF1_PRST_PHY_CLKREQ | + P_CF1_ENA_CFG_LDR_DONE | + P_CF1_ENA_TXBMU_RD_IDLE | + P_CF1_ENA_TXBMU_WR_IDLE, +}; + + +#define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \ + PCI_STATUS_SIG_SYSTEM_ERROR | \ + PCI_STATUS_REC_MASTER_ABORT | \ + PCI_STATUS_REC_TARGET_ABORT | \ + PCI_STATUS_PARITY) + +enum csr_regs { + B0_RAP = 0x0000, + B0_CTST = 0x0004, + B0_Y2LED = 0x0005, + B0_POWER_CTRL = 0x0007, + B0_ISRC = 0x0008, + B0_IMSK = 0x000c, + B0_HWE_ISRC = 0x0010, + B0_HWE_IMSK = 0x0014, + + /* Special ISR registers (Yukon-2 only) */ + B0_Y2_SP_ISRC2 = 0x001c, + B0_Y2_SP_ISRC3 = 0x0020, + B0_Y2_SP_EISR = 0x0024, + B0_Y2_SP_LISR = 0x0028, + B0_Y2_SP_ICR = 0x002c, + + B2_MAC_1 = 0x0100, + B2_MAC_2 = 0x0108, + B2_MAC_3 = 0x0110, + B2_CONN_TYP = 0x0118, + B2_PMD_TYP = 0x0119, + B2_MAC_CFG = 0x011a, + B2_CHIP_ID = 0x011b, + B2_E_0 = 0x011c, + + B2_Y2_CLK_GATE = 0x011d, + B2_Y2_HW_RES = 0x011e, + B2_E_3 = 0x011f, + B2_Y2_CLK_CTRL = 0x0120, + + B2_TI_INI = 0x0130, + B2_TI_VAL = 0x0134, + B2_TI_CTRL = 0x0138, + B2_TI_TEST = 0x0139, + + B2_TST_CTRL1 = 0x0158, + B2_TST_CTRL2 = 0x0159, + B2_GP_IO = 0x015c, + + B2_I2C_CTRL = 0x0160, + B2_I2C_DATA = 0x0164, + B2_I2C_IRQ = 0x0168, + B2_I2C_SW = 0x016c, + + B3_RAM_ADDR = 0x0180, + B3_RAM_DATA_LO = 0x0184, + B3_RAM_DATA_HI = 0x0188, + +/* RAM Interface Registers */ +/* Yukon-2: use RAM_BUFFER() to access the RAM buffer */ +/* + * The HW-Spec. calls this registers Timeout Value 0..11. But this names are + * not usable in SW. Please notice these are NOT real timeouts, these are + * the number of qWords transferred continuously. + */ +#define RAM_BUFFER(port, reg) (reg | (port <<6)) + + B3_RI_WTO_R1 = 0x0190, + B3_RI_WTO_XA1 = 0x0191, + B3_RI_WTO_XS1 = 0x0192, + B3_RI_RTO_R1 = 0x0193, + B3_RI_RTO_XA1 = 0x0194, + B3_RI_RTO_XS1 = 0x0195, + B3_RI_WTO_R2 = 0x0196, + B3_RI_WTO_XA2 = 0x0197, + B3_RI_WTO_XS2 = 0x0198, + B3_RI_RTO_R2 = 0x0199, + B3_RI_RTO_XA2 = 0x019a, + B3_RI_RTO_XS2 = 0x019b, + B3_RI_TO_VAL = 0x019c, + B3_RI_CTRL = 0x01a0, + B3_RI_TEST = 0x01a2, + B3_MA_TOINI_RX1 = 0x01b0, + B3_MA_TOINI_RX2 = 0x01b1, + B3_MA_TOINI_TX1 = 0x01b2, + B3_MA_TOINI_TX2 = 0x01b3, + B3_MA_TOVAL_RX1 = 0x01b4, + B3_MA_TOVAL_RX2 = 0x01b5, + B3_MA_TOVAL_TX1 = 0x01b6, + B3_MA_TOVAL_TX2 = 0x01b7, + B3_MA_TO_CTRL = 0x01b8, + B3_MA_TO_TEST = 0x01ba, + B3_MA_RCINI_RX1 = 0x01c0, + B3_MA_RCINI_RX2 = 0x01c1, + B3_MA_RCINI_TX1 = 0x01c2, + B3_MA_RCINI_TX2 = 0x01c3, + B3_MA_RCVAL_RX1 = 0x01c4, + B3_MA_RCVAL_RX2 = 0x01c5, + B3_MA_RCVAL_TX1 = 0x01c6, + B3_MA_RCVAL_TX2 = 0x01c7, + B3_MA_RC_CTRL = 0x01c8, + B3_MA_RC_TEST = 0x01ca, + B3_PA_TOINI_RX1 = 0x01d0, + B3_PA_TOINI_RX2 = 0x01d4, + B3_PA_TOINI_TX1 = 0x01d8, + B3_PA_TOINI_TX2 = 0x01dc, + B3_PA_TOVAL_RX1 = 0x01e0, + B3_PA_TOVAL_RX2 = 0x01e4, + B3_PA_TOVAL_TX1 = 0x01e8, + B3_PA_TOVAL_TX2 = 0x01ec, + B3_PA_CTRL = 0x01f0, + B3_PA_TEST = 0x01f2, + + Y2_CFG_SPC = 0x1c00, /* PCI config space region */ + Y2_CFG_AER = 0x1d00, /* PCI Advanced Error Report region */ +}; + +/* B0_CTST 16 bit Control/Status register */ +enum { + Y2_VMAIN_AVAIL = 1<<17,/* VMAIN available (YUKON-2 only) */ + Y2_VAUX_AVAIL = 1<<16,/* VAUX available (YUKON-2 only) */ + Y2_HW_WOL_ON = 1<<15,/* HW WOL On (Yukon-EC Ultra A1 only) */ + Y2_HW_WOL_OFF = 1<<14,/* HW WOL On (Yukon-EC Ultra A1 only) */ + Y2_ASF_ENABLE = 1<<13,/* ASF Unit Enable (YUKON-2 only) */ + Y2_ASF_DISABLE = 1<<12,/* ASF Unit Disable (YUKON-2 only) */ + Y2_CLK_RUN_ENA = 1<<11,/* CLK_RUN Enable (YUKON-2 only) */ + Y2_CLK_RUN_DIS = 1<<10,/* CLK_RUN Disable (YUKON-2 only) */ + Y2_LED_STAT_ON = 1<<9, /* Status LED On (YUKON-2 only) */ + Y2_LED_STAT_OFF = 1<<8, /* Status LED Off (YUKON-2 only) */ + + CS_ST_SW_IRQ = 1<<7, /* Set IRQ SW Request */ + CS_CL_SW_IRQ = 1<<6, /* Clear IRQ SW Request */ + CS_STOP_DONE = 1<<5, /* Stop Master is finished */ + CS_STOP_MAST = 1<<4, /* Command Bit to stop the master */ + CS_MRST_CLR = 1<<3, /* Clear Master reset */ + CS_MRST_SET = 1<<2, /* Set Master reset */ + CS_RST_CLR = 1<<1, /* Clear Software reset */ + CS_RST_SET = 1, /* Set Software reset */ +}; + +/* B0_LED 8 Bit LED register */ +enum { +/* Bit 7.. 2: reserved */ + LED_STAT_ON = 1<<1, /* Status LED on */ + LED_STAT_OFF = 1, /* Status LED off */ +}; + +/* B0_POWER_CTRL 8 Bit Power Control reg (YUKON only) */ +enum { + PC_VAUX_ENA = 1<<7, /* Switch VAUX Enable */ + PC_VAUX_DIS = 1<<6, /* Switch VAUX Disable */ + PC_VCC_ENA = 1<<5, /* Switch VCC Enable */ + PC_VCC_DIS = 1<<4, /* Switch VCC Disable */ + PC_VAUX_ON = 1<<3, /* Switch VAUX On */ + PC_VAUX_OFF = 1<<2, /* Switch VAUX Off */ + PC_VCC_ON = 1<<1, /* Switch VCC On */ + PC_VCC_OFF = 1<<0, /* Switch VCC Off */ +}; + +/* B2_IRQM_MSK 32 bit IRQ Moderation Mask */ + +/* B0_Y2_SP_ISRC2 32 bit Special Interrupt Source Reg 2 */ +/* B0_Y2_SP_ISRC3 32 bit Special Interrupt Source Reg 3 */ +/* B0_Y2_SP_EISR 32 bit Enter ISR Reg */ +/* B0_Y2_SP_LISR 32 bit Leave ISR Reg */ +enum { + Y2_IS_HW_ERR = 1<<31, /* Interrupt HW Error */ + Y2_IS_STAT_BMU = 1<<30, /* Status BMU Interrupt */ + Y2_IS_ASF = 1<<29, /* ASF subsystem Interrupt */ + + Y2_IS_POLL_CHK = 1<<27, /* Check IRQ from polling unit */ + Y2_IS_TWSI_RDY = 1<<26, /* IRQ on end of TWSI Tx */ + Y2_IS_IRQ_SW = 1<<25, /* SW forced IRQ */ + Y2_IS_TIMINT = 1<<24, /* IRQ from Timer */ + + Y2_IS_IRQ_PHY2 = 1<<12, /* Interrupt from PHY 2 */ + Y2_IS_IRQ_MAC2 = 1<<11, /* Interrupt from MAC 2 */ + Y2_IS_CHK_RX2 = 1<<10, /* Descriptor error Rx 2 */ + Y2_IS_CHK_TXS2 = 1<<9, /* Descriptor error TXS 2 */ + Y2_IS_CHK_TXA2 = 1<<8, /* Descriptor error TXA 2 */ + + Y2_IS_IRQ_PHY1 = 1<<4, /* Interrupt from PHY 1 */ + Y2_IS_IRQ_MAC1 = 1<<3, /* Interrupt from MAC 1 */ + Y2_IS_CHK_RX1 = 1<<2, /* Descriptor error Rx 1 */ + Y2_IS_CHK_TXS1 = 1<<1, /* Descriptor error TXS 1 */ + Y2_IS_CHK_TXA1 = 1<<0, /* Descriptor error TXA 1 */ + + Y2_IS_BASE = Y2_IS_HW_ERR | Y2_IS_STAT_BMU, + Y2_IS_PORT_1 = Y2_IS_IRQ_PHY1 | Y2_IS_IRQ_MAC1 + | Y2_IS_CHK_TXA1 | Y2_IS_CHK_RX1, + Y2_IS_PORT_2 = Y2_IS_IRQ_PHY2 | Y2_IS_IRQ_MAC2 + | Y2_IS_CHK_TXA2 | Y2_IS_CHK_RX2, + Y2_IS_ERROR = Y2_IS_HW_ERR | + Y2_IS_IRQ_MAC1 | Y2_IS_CHK_TXA1 | Y2_IS_CHK_RX1 | + Y2_IS_IRQ_MAC2 | Y2_IS_CHK_TXA2 | Y2_IS_CHK_RX2, +}; + +/* B2_IRQM_HWE_MSK 32 bit IRQ Moderation HW Error Mask */ +enum { + IS_ERR_MSK = 0x00003fff,/* All Error bits */ + + IS_IRQ_TIST_OV = 1<<13, /* Time Stamp Timer Overflow (YUKON only) */ + IS_IRQ_SENSOR = 1<<12, /* IRQ from Sensor (YUKON only) */ + IS_IRQ_MST_ERR = 1<<11, /* IRQ master error detected */ + IS_IRQ_STAT = 1<<10, /* IRQ status exception */ + IS_NO_STAT_M1 = 1<<9, /* No Rx Status from MAC 1 */ + IS_NO_STAT_M2 = 1<<8, /* No Rx Status from MAC 2 */ + IS_NO_TIST_M1 = 1<<7, /* No Time Stamp from MAC 1 */ + IS_NO_TIST_M2 = 1<<6, /* No Time Stamp from MAC 2 */ + IS_RAM_RD_PAR = 1<<5, /* RAM Read Parity Error */ + IS_RAM_WR_PAR = 1<<4, /* RAM Write Parity Error */ + IS_M1_PAR_ERR = 1<<3, /* MAC 1 Parity Error */ + IS_M2_PAR_ERR = 1<<2, /* MAC 2 Parity Error */ + IS_R1_PAR_ERR = 1<<1, /* Queue R1 Parity Error */ + IS_R2_PAR_ERR = 1<<0, /* Queue R2 Parity Error */ +}; + +/* Hardware error interrupt mask for Yukon 2 */ +enum { + Y2_IS_TIST_OV = 1<<29,/* Time Stamp Timer overflow interrupt */ + Y2_IS_SENSOR = 1<<28, /* Sensor interrupt */ + Y2_IS_MST_ERR = 1<<27, /* Master error interrupt */ + Y2_IS_IRQ_STAT = 1<<26, /* Status exception interrupt */ + Y2_IS_PCI_EXP = 1<<25, /* PCI-Express interrupt */ + Y2_IS_PCI_NEXP = 1<<24, /* PCI-Express error similar to PCI error */ + /* Link 2 */ + Y2_IS_PAR_RD2 = 1<<13, /* Read RAM parity error interrupt */ + Y2_IS_PAR_WR2 = 1<<12, /* Write RAM parity error interrupt */ + Y2_IS_PAR_MAC2 = 1<<11, /* MAC hardware fault interrupt */ + Y2_IS_PAR_RX2 = 1<<10, /* Parity Error Rx Queue 2 */ + Y2_IS_TCP_TXS2 = 1<<9, /* TCP length mismatch sync Tx queue IRQ */ + Y2_IS_TCP_TXA2 = 1<<8, /* TCP length mismatch async Tx queue IRQ */ + /* Link 1 */ + Y2_IS_PAR_RD1 = 1<<5, /* Read RAM parity error interrupt */ + Y2_IS_PAR_WR1 = 1<<4, /* Write RAM parity error interrupt */ + Y2_IS_PAR_MAC1 = 1<<3, /* MAC hardware fault interrupt */ + Y2_IS_PAR_RX1 = 1<<2, /* Parity Error Rx Queue 1 */ + Y2_IS_TCP_TXS1 = 1<<1, /* TCP length mismatch sync Tx queue IRQ */ + Y2_IS_TCP_TXA1 = 1<<0, /* TCP length mismatch async Tx queue IRQ */ + + Y2_HWE_L1_MASK = Y2_IS_PAR_RD1 | Y2_IS_PAR_WR1 | Y2_IS_PAR_MAC1 | + Y2_IS_PAR_RX1 | Y2_IS_TCP_TXS1| Y2_IS_TCP_TXA1, + Y2_HWE_L2_MASK = Y2_IS_PAR_RD2 | Y2_IS_PAR_WR2 | Y2_IS_PAR_MAC2 | + Y2_IS_PAR_RX2 | Y2_IS_TCP_TXS2| Y2_IS_TCP_TXA2, + + Y2_HWE_ALL_MASK = Y2_IS_TIST_OV | Y2_IS_MST_ERR | Y2_IS_IRQ_STAT | + Y2_HWE_L1_MASK | Y2_HWE_L2_MASK, +}; + +/* B28_DPT_CTRL 8 bit Descriptor Poll Timer Ctrl Reg */ +enum { + DPT_START = 1<<1, + DPT_STOP = 1<<0, +}; + +/* B2_TST_CTRL1 8 bit Test Control Register 1 */ +enum { + TST_FRC_DPERR_MR = 1<<7, /* force DATAPERR on MST RD */ + TST_FRC_DPERR_MW = 1<<6, /* force DATAPERR on MST WR */ + TST_FRC_DPERR_TR = 1<<5, /* force DATAPERR on TRG RD */ + TST_FRC_DPERR_TW = 1<<4, /* force DATAPERR on TRG WR */ + TST_FRC_APERR_M = 1<<3, /* force ADDRPERR on MST */ + TST_FRC_APERR_T = 1<<2, /* force ADDRPERR on TRG */ + TST_CFG_WRITE_ON = 1<<1, /* Enable Config Reg WR */ + TST_CFG_WRITE_OFF= 1<<0, /* Disable Config Reg WR */ +}; + +/* B2_GPIO */ +enum { + GLB_GPIO_CLK_DEB_ENA = 1<<31, /* Clock Debug Enable */ + GLB_GPIO_CLK_DBG_MSK = 0xf<<26, /* Clock Debug */ + + GLB_GPIO_INT_RST_D3_DIS = 1<<15, /* Disable Internal Reset After D3 to D0 */ + GLB_GPIO_LED_PAD_SPEED_UP = 1<<14, /* LED PAD Speed Up */ + GLB_GPIO_STAT_RACE_DIS = 1<<13, /* Status Race Disable */ + GLB_GPIO_TEST_SEL_MSK = 3<<11, /* Testmode Select */ + GLB_GPIO_TEST_SEL_BASE = 1<<11, + GLB_GPIO_RAND_ENA = 1<<10, /* Random Enable */ + GLB_GPIO_RAND_BIT_1 = 1<<9, /* Random Bit 1 */ +}; + +/* B2_MAC_CFG 8 bit MAC Configuration / Chip Revision */ +enum { + CFG_CHIP_R_MSK = 0xf<<4, /* Bit 7.. 4: Chip Revision */ + /* Bit 3.. 2: reserved */ + CFG_DIS_M2_CLK = 1<<1, /* Disable Clock for 2nd MAC */ + CFG_SNG_MAC = 1<<0, /* MAC Config: 0=2 MACs / 1=1 MAC*/ +}; + +/* B2_CHIP_ID 8 bit Chip Identification Number */ +enum { + CHIP_ID_YUKON_XL = 0xb3, /* YUKON-2 XL */ + CHIP_ID_YUKON_EC_U = 0xb4, /* YUKON-2 EC Ultra */ + CHIP_ID_YUKON_EX = 0xb5, /* YUKON-2 Extreme */ + CHIP_ID_YUKON_EC = 0xb6, /* YUKON-2 EC */ + CHIP_ID_YUKON_FE = 0xb7, /* YUKON-2 FE */ + CHIP_ID_YUKON_FE_P = 0xb8, /* YUKON-2 FE+ */ + CHIP_ID_YUKON_SUPR = 0xb9, /* YUKON-2 Supreme */ + CHIP_ID_YUKON_UL_2 = 0xba, /* YUKON-2 Ultra 2 */ +}; +enum yukon_ec_rev { + CHIP_REV_YU_EC_A1 = 0, /* Chip Rev. for Yukon-EC A1/A0 */ + CHIP_REV_YU_EC_A2 = 1, /* Chip Rev. for Yukon-EC A2 */ + CHIP_REV_YU_EC_A3 = 2, /* Chip Rev. for Yukon-EC A3 */ +}; +enum yukon_ec_u_rev { + CHIP_REV_YU_EC_U_A0 = 1, + CHIP_REV_YU_EC_U_A1 = 2, + CHIP_REV_YU_EC_U_B0 = 3, +}; +enum yukon_fe_rev { + CHIP_REV_YU_FE_A1 = 1, + CHIP_REV_YU_FE_A2 = 2, +}; +enum yukon_fe_p_rev { + CHIP_REV_YU_FE2_A0 = 0, +}; +enum yukon_ex_rev { + CHIP_REV_YU_EX_A0 = 1, + CHIP_REV_YU_EX_B0 = 2, +}; +enum yukon_supr_rev { + CHIP_REV_YU_SU_A0 = 0, +}; + + +/* B2_Y2_CLK_GATE 8 bit Clock Gating (Yukon-2 only) */ +enum { + Y2_STATUS_LNK2_INAC = 1<<7, /* Status Link 2 inactive (0 = active) */ + Y2_CLK_GAT_LNK2_DIS = 1<<6, /* Disable clock gating Link 2 */ + Y2_COR_CLK_LNK2_DIS = 1<<5, /* Disable Core clock Link 2 */ + Y2_PCI_CLK_LNK2_DIS = 1<<4, /* Disable PCI clock Link 2 */ + Y2_STATUS_LNK1_INAC = 1<<3, /* Status Link 1 inactive (0 = active) */ + Y2_CLK_GAT_LNK1_DIS = 1<<2, /* Disable clock gating Link 1 */ + Y2_COR_CLK_LNK1_DIS = 1<<1, /* Disable Core clock Link 1 */ + Y2_PCI_CLK_LNK1_DIS = 1<<0, /* Disable PCI clock Link 1 */ +}; + +/* B2_Y2_HW_RES 8 bit HW Resources (Yukon-2 only) */ +enum { + CFG_LED_MODE_MSK = 7<<2, /* Bit 4.. 2: LED Mode Mask */ + CFG_LINK_2_AVAIL = 1<<1, /* Link 2 available */ + CFG_LINK_1_AVAIL = 1<<0, /* Link 1 available */ +}; +#define CFG_LED_MODE(x) (((x) & CFG_LED_MODE_MSK) >> 2) +#define CFG_DUAL_MAC_MSK (CFG_LINK_2_AVAIL | CFG_LINK_1_AVAIL) + + +/* B2_Y2_CLK_CTRL 32 bit Clock Frequency Control Register (Yukon-2/EC) */ +enum { + Y2_CLK_DIV_VAL_MSK = 0xff<<16,/* Bit 23..16: Clock Divisor Value */ +#define Y2_CLK_DIV_VAL(x) (((x)<<16) & Y2_CLK_DIV_VAL_MSK) + Y2_CLK_DIV_VAL2_MSK = 7<<21, /* Bit 23..21: Clock Divisor Value */ + Y2_CLK_SELECT2_MSK = 0x1f<<16,/* Bit 20..16: Clock Select */ +#define Y2_CLK_DIV_VAL_2(x) (((x)<<21) & Y2_CLK_DIV_VAL2_MSK) +#define Y2_CLK_SEL_VAL_2(x) (((x)<<16) & Y2_CLK_SELECT2_MSK) + Y2_CLK_DIV_ENA = 1<<1, /* Enable Core Clock Division */ + Y2_CLK_DIV_DIS = 1<<0, /* Disable Core Clock Division */ +}; + +/* B2_TI_CTRL 8 bit Timer control */ +/* B2_IRQM_CTRL 8 bit IRQ Moderation Timer Control */ +enum { + TIM_START = 1<<2, /* Start Timer */ + TIM_STOP = 1<<1, /* Stop Timer */ + TIM_CLR_IRQ = 1<<0, /* Clear Timer IRQ (!IRQM) */ +}; + +/* B2_TI_TEST 8 Bit Timer Test */ +/* B2_IRQM_TEST 8 bit IRQ Moderation Timer Test */ +/* B28_DPT_TST 8 bit Descriptor Poll Timer Test Reg */ +enum { + TIM_T_ON = 1<<2, /* Test mode on */ + TIM_T_OFF = 1<<1, /* Test mode off */ + TIM_T_STEP = 1<<0, /* Test step */ +}; + +/* B3_RAM_ADDR 32 bit RAM Address, to read or write */ + /* Bit 31..19: reserved */ +#define RAM_ADR_RAN 0x0007ffffL /* Bit 18.. 0: RAM Address Range */ +/* RAM Interface Registers */ + +/* B3_RI_CTRL 16 bit RAM Interface Control Register */ +enum { + RI_CLR_RD_PERR = 1<<9, /* Clear IRQ RAM Read Parity Err */ + RI_CLR_WR_PERR = 1<<8, /* Clear IRQ RAM Write Parity Err*/ + + RI_RST_CLR = 1<<1, /* Clear RAM Interface Reset */ + RI_RST_SET = 1<<0, /* Set RAM Interface Reset */ +}; + +#define SK_RI_TO_53 36 /* RAM interface timeout */ + + +/* Port related registers FIFO, and Arbiter */ +#define SK_REG(port,reg) (((port)<<7)+(reg)) + +/* Transmit Arbiter Registers MAC 1 and 2, use SK_REG() to access */ +/* TXA_ITI_INI 32 bit Tx Arb Interval Timer Init Val */ +/* TXA_ITI_VAL 32 bit Tx Arb Interval Timer Value */ +/* TXA_LIM_INI 32 bit Tx Arb Limit Counter Init Val */ +/* TXA_LIM_VAL 32 bit Tx Arb Limit Counter Value */ + +#define TXA_MAX_VAL 0x00ffffffUL /* Bit 23.. 0: Max TXA Timer/Cnt Val */ + +/* TXA_CTRL 8 bit Tx Arbiter Control Register */ +enum { + TXA_ENA_FSYNC = 1<<7, /* Enable force of sync Tx queue */ + TXA_DIS_FSYNC = 1<<6, /* Disable force of sync Tx queue */ + TXA_ENA_ALLOC = 1<<5, /* Enable alloc of free bandwidth */ + TXA_DIS_ALLOC = 1<<4, /* Disable alloc of free bandwidth */ + TXA_START_RC = 1<<3, /* Start sync Rate Control */ + TXA_STOP_RC = 1<<2, /* Stop sync Rate Control */ + TXA_ENA_ARB = 1<<1, /* Enable Tx Arbiter */ + TXA_DIS_ARB = 1<<0, /* Disable Tx Arbiter */ +}; + +/* + * Bank 4 - 5 + */ +/* Transmit Arbiter Registers MAC 1 and 2, use SK_REG() to access */ +enum { + TXA_ITI_INI = 0x0200,/* 32 bit Tx Arb Interval Timer Init Val*/ + TXA_ITI_VAL = 0x0204,/* 32 bit Tx Arb Interval Timer Value */ + TXA_LIM_INI = 0x0208,/* 32 bit Tx Arb Limit Counter Init Val */ + TXA_LIM_VAL = 0x020c,/* 32 bit Tx Arb Limit Counter Value */ + TXA_CTRL = 0x0210,/* 8 bit Tx Arbiter Control Register */ + TXA_TEST = 0x0211,/* 8 bit Tx Arbiter Test Register */ + TXA_STAT = 0x0212,/* 8 bit Tx Arbiter Status Register */ +}; + + +enum { + B6_EXT_REG = 0x0300,/* External registers (GENESIS only) */ + B7_CFG_SPC = 0x0380,/* copy of the Configuration register */ + B8_RQ1_REGS = 0x0400,/* Receive Queue 1 */ + B8_RQ2_REGS = 0x0480,/* Receive Queue 2 */ + B8_TS1_REGS = 0x0600,/* Transmit sync queue 1 */ + B8_TA1_REGS = 0x0680,/* Transmit async queue 1 */ + B8_TS2_REGS = 0x0700,/* Transmit sync queue 2 */ + B8_TA2_REGS = 0x0780,/* Transmit sync queue 2 */ + B16_RAM_REGS = 0x0800,/* RAM Buffer Registers */ +}; + +/* Queue Register Offsets, use Q_ADDR() to access */ +enum { + B8_Q_REGS = 0x0400, /* base of Queue registers */ + Q_D = 0x00, /* 8*32 bit Current Descriptor */ + Q_VLAN = 0x20, /* 16 bit Current VLAN Tag */ + Q_DONE = 0x24, /* 16 bit Done Index */ + Q_AC_L = 0x28, /* 32 bit Current Address Counter Low dWord */ + Q_AC_H = 0x2c, /* 32 bit Current Address Counter High dWord */ + Q_BC = 0x30, /* 32 bit Current Byte Counter */ + Q_CSR = 0x34, /* 32 bit BMU Control/Status Register */ + Q_TEST = 0x38, /* 32 bit Test/Control Register */ + +/* Yukon-2 */ + Q_WM = 0x40, /* 16 bit FIFO Watermark */ + Q_AL = 0x42, /* 8 bit FIFO Alignment */ + Q_RSP = 0x44, /* 16 bit FIFO Read Shadow Pointer */ + Q_RSL = 0x46, /* 8 bit FIFO Read Shadow Level */ + Q_RP = 0x48, /* 8 bit FIFO Read Pointer */ + Q_RL = 0x4a, /* 8 bit FIFO Read Level */ + Q_WP = 0x4c, /* 8 bit FIFO Write Pointer */ + Q_WSP = 0x4d, /* 8 bit FIFO Write Shadow Pointer */ + Q_WL = 0x4e, /* 8 bit FIFO Write Level */ + Q_WSL = 0x4f, /* 8 bit FIFO Write Shadow Level */ +}; +#define Q_ADDR(reg, offs) (B8_Q_REGS + (reg) + (offs)) + +/* Q_TEST 32 bit Test Register */ +enum { + /* Transmit */ + F_TX_CHK_AUTO_OFF = 1<<31, /* Tx checksum auto calc off (Yukon EX) */ + F_TX_CHK_AUTO_ON = 1<<30, /* Tx checksum auto calc off (Yukon EX) */ + + /* Receive */ + F_M_RX_RAM_DIS = 1<<24, /* MAC Rx RAM Read Port disable */ + + /* Hardware testbits not used */ +}; + +/* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/ +enum { + Y2_B8_PREF_REGS = 0x0450, + + PREF_UNIT_CTRL = 0x00, /* 32 bit Control register */ + PREF_UNIT_LAST_IDX = 0x04, /* 16 bit Last Index */ + PREF_UNIT_ADDR_LO = 0x08, /* 32 bit List start addr, low part */ + PREF_UNIT_ADDR_HI = 0x0c, /* 32 bit List start addr, high part*/ + PREF_UNIT_GET_IDX = 0x10, /* 16 bit Get Index */ + PREF_UNIT_PUT_IDX = 0x14, /* 16 bit Put Index */ + PREF_UNIT_FIFO_WP = 0x20, /* 8 bit FIFO write pointer */ + PREF_UNIT_FIFO_RP = 0x24, /* 8 bit FIFO read pointer */ + PREF_UNIT_FIFO_WM = 0x28, /* 8 bit FIFO watermark */ + PREF_UNIT_FIFO_LEV = 0x2c, /* 8 bit FIFO level */ + + PREF_UNIT_MASK_IDX = 0x0fff, +}; +#define Y2_QADDR(q,reg) (Y2_B8_PREF_REGS + (q) + (reg)) + +/* RAM Buffer Register Offsets */ +enum { + + RB_START = 0x00,/* 32 bit RAM Buffer Start Address */ + RB_END = 0x04,/* 32 bit RAM Buffer End Address */ + RB_WP = 0x08,/* 32 bit RAM Buffer Write Pointer */ + RB_RP = 0x0c,/* 32 bit RAM Buffer Read Pointer */ + RB_RX_UTPP = 0x10,/* 32 bit Rx Upper Threshold, Pause Packet */ + RB_RX_LTPP = 0x14,/* 32 bit Rx Lower Threshold, Pause Packet */ + RB_RX_UTHP = 0x18,/* 32 bit Rx Upper Threshold, High Prio */ + RB_RX_LTHP = 0x1c,/* 32 bit Rx Lower Threshold, High Prio */ + /* 0x10 - 0x1f: reserved at Tx RAM Buffer Registers */ + RB_PC = 0x20,/* 32 bit RAM Buffer Packet Counter */ + RB_LEV = 0x24,/* 32 bit RAM Buffer Level Register */ + RB_CTRL = 0x28,/* 32 bit RAM Buffer Control Register */ + RB_TST1 = 0x29,/* 8 bit RAM Buffer Test Register 1 */ + RB_TST2 = 0x2a,/* 8 bit RAM Buffer Test Register 2 */ +}; + +/* Receive and Transmit Queues */ +enum { + Q_R1 = 0x0000, /* Receive Queue 1 */ + Q_R2 = 0x0080, /* Receive Queue 2 */ + Q_XS1 = 0x0200, /* Synchronous Transmit Queue 1 */ + Q_XA1 = 0x0280, /* Asynchronous Transmit Queue 1 */ + Q_XS2 = 0x0300, /* Synchronous Transmit Queue 2 */ + Q_XA2 = 0x0380, /* Asynchronous Transmit Queue 2 */ +}; + +/* Different PHY Types */ +enum { + PHY_ADDR_MARV = 0, +}; + +#define RB_ADDR(offs, queue) ((u16) B16_RAM_REGS + (queue) + (offs)) + + +enum { + LNK_SYNC_INI = 0x0c30,/* 32 bit Link Sync Cnt Init Value */ + LNK_SYNC_VAL = 0x0c34,/* 32 bit Link Sync Cnt Current Value */ + LNK_SYNC_CTRL = 0x0c38,/* 8 bit Link Sync Cnt Control Register */ + LNK_SYNC_TST = 0x0c39,/* 8 bit Link Sync Cnt Test Register */ + + LNK_LED_REG = 0x0c3c,/* 8 bit Link LED Register */ + +/* Receive GMAC FIFO (YUKON and Yukon-2) */ + + RX_GMF_EA = 0x0c40,/* 32 bit Rx GMAC FIFO End Address */ + RX_GMF_AF_THR = 0x0c44,/* 32 bit Rx GMAC FIFO Almost Full Thresh. */ + RX_GMF_CTRL_T = 0x0c48,/* 32 bit Rx GMAC FIFO Control/Test */ + RX_GMF_FL_MSK = 0x0c4c,/* 32 bit Rx GMAC FIFO Flush Mask */ + RX_GMF_FL_THR = 0x0c50,/* 32 bit Rx GMAC FIFO Flush Threshold */ + RX_GMF_TR_THR = 0x0c54,/* 32 bit Rx Truncation Threshold (Yukon-2) */ + RX_GMF_UP_THR = 0x0c58,/* 8 bit Rx Upper Pause Thr (Yukon-EC_U) */ + RX_GMF_LP_THR = 0x0c5a,/* 8 bit Rx Lower Pause Thr (Yukon-EC_U) */ + RX_GMF_VLAN = 0x0c5c,/* 32 bit Rx VLAN Type Register (Yukon-2) */ + RX_GMF_WP = 0x0c60,/* 32 bit Rx GMAC FIFO Write Pointer */ + + RX_GMF_WLEV = 0x0c68,/* 32 bit Rx GMAC FIFO Write Level */ + + RX_GMF_RP = 0x0c70,/* 32 bit Rx GMAC FIFO Read Pointer */ + + RX_GMF_RLEV = 0x0c78,/* 32 bit Rx GMAC FIFO Read Level */ +}; + + +/* Q_BC 32 bit Current Byte Counter */ + +/* BMU Control Status Registers */ +/* B0_R1_CSR 32 bit BMU Ctrl/Stat Rx Queue 1 */ +/* B0_R2_CSR 32 bit BMU Ctrl/Stat Rx Queue 2 */ +/* B0_XA1_CSR 32 bit BMU Ctrl/Stat Sync Tx Queue 1 */ +/* B0_XS1_CSR 32 bit BMU Ctrl/Stat Async Tx Queue 1 */ +/* B0_XA2_CSR 32 bit BMU Ctrl/Stat Sync Tx Queue 2 */ +/* B0_XS2_CSR 32 bit BMU Ctrl/Stat Async Tx Queue 2 */ +/* Q_CSR 32 bit BMU Control/Status Register */ + +/* Rx BMU Control / Status Registers (Yukon-2) */ +enum { + BMU_IDLE = 1<<31, /* BMU Idle State */ + BMU_RX_TCP_PKT = 1<<30, /* Rx TCP Packet (when RSS Hash enabled) */ + BMU_RX_IP_PKT = 1<<29, /* Rx IP Packet (when RSS Hash enabled) */ + + BMU_ENA_RX_RSS_HASH = 1<<15, /* Enable Rx RSS Hash */ + BMU_DIS_RX_RSS_HASH = 1<<14, /* Disable Rx RSS Hash */ + BMU_ENA_RX_CHKSUM = 1<<13, /* Enable Rx TCP/IP Checksum Check */ + BMU_DIS_RX_CHKSUM = 1<<12, /* Disable Rx TCP/IP Checksum Check */ + BMU_CLR_IRQ_PAR = 1<<11, /* Clear IRQ on Parity errors (Rx) */ + BMU_CLR_IRQ_TCP = 1<<11, /* Clear IRQ on TCP segment. error (Tx) */ + BMU_CLR_IRQ_CHK = 1<<10, /* Clear IRQ Check */ + BMU_STOP = 1<<9, /* Stop Rx/Tx Queue */ + BMU_START = 1<<8, /* Start Rx/Tx Queue */ + BMU_FIFO_OP_ON = 1<<7, /* FIFO Operational On */ + BMU_FIFO_OP_OFF = 1<<6, /* FIFO Operational Off */ + BMU_FIFO_ENA = 1<<5, /* Enable FIFO */ + BMU_FIFO_RST = 1<<4, /* Reset FIFO */ + BMU_OP_ON = 1<<3, /* BMU Operational On */ + BMU_OP_OFF = 1<<2, /* BMU Operational Off */ + BMU_RST_CLR = 1<<1, /* Clear BMU Reset (Enable) */ + BMU_RST_SET = 1<<0, /* Set BMU Reset */ + + BMU_CLR_RESET = BMU_FIFO_RST | BMU_OP_OFF | BMU_RST_CLR, + BMU_OPER_INIT = BMU_CLR_IRQ_PAR | BMU_CLR_IRQ_CHK | BMU_START | + BMU_FIFO_ENA | BMU_OP_ON, + + BMU_WM_DEFAULT = 0x600, + BMU_WM_PEX = 0x80, +}; + +/* Tx BMU Control / Status Registers (Yukon-2) */ + /* Bit 31: same as for Rx */ +enum { + BMU_TX_IPIDINCR_ON = 1<<13, /* Enable IP ID Increment */ + BMU_TX_IPIDINCR_OFF = 1<<12, /* Disable IP ID Increment */ + BMU_TX_CLR_IRQ_TCP = 1<<11, /* Clear IRQ on TCP segment length mismatch */ +}; + +/* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/ +/* PREF_UNIT_CTRL 32 bit Prefetch Control register */ +enum { + PREF_UNIT_OP_ON = 1<<3, /* prefetch unit operational */ + PREF_UNIT_OP_OFF = 1<<2, /* prefetch unit not operational */ + PREF_UNIT_RST_CLR = 1<<1, /* Clear Prefetch Unit Reset */ + PREF_UNIT_RST_SET = 1<<0, /* Set Prefetch Unit Reset */ +}; + +/* RAM Buffer Register Offsets, use RB_ADDR(Queue, Offs) to access */ +/* RB_START 32 bit RAM Buffer Start Address */ +/* RB_END 32 bit RAM Buffer End Address */ +/* RB_WP 32 bit RAM Buffer Write Pointer */ +/* RB_RP 32 bit RAM Buffer Read Pointer */ +/* RB_RX_UTPP 32 bit Rx Upper Threshold, Pause Pack */ +/* RB_RX_LTPP 32 bit Rx Lower Threshold, Pause Pack */ +/* RB_RX_UTHP 32 bit Rx Upper Threshold, High Prio */ +/* RB_RX_LTHP 32 bit Rx Lower Threshold, High Prio */ +/* RB_PC 32 bit RAM Buffer Packet Counter */ +/* RB_LEV 32 bit RAM Buffer Level Register */ + +#define RB_MSK 0x0007ffff /* Bit 18.. 0: RAM Buffer Pointer Bits */ +/* RB_TST2 8 bit RAM Buffer Test Register 2 */ +/* RB_TST1 8 bit RAM Buffer Test Register 1 */ + +/* RB_CTRL 8 bit RAM Buffer Control Register */ +enum { + RB_ENA_STFWD = 1<<5, /* Enable Store & Forward */ + RB_DIS_STFWD = 1<<4, /* Disable Store & Forward */ + RB_ENA_OP_MD = 1<<3, /* Enable Operation Mode */ + RB_DIS_OP_MD = 1<<2, /* Disable Operation Mode */ + RB_RST_CLR = 1<<1, /* Clear RAM Buf STM Reset */ + RB_RST_SET = 1<<0, /* Set RAM Buf STM Reset */ +}; + + +/* Transmit GMAC FIFO (YUKON only) */ +enum { + TX_GMF_EA = 0x0d40,/* 32 bit Tx GMAC FIFO End Address */ + TX_GMF_AE_THR = 0x0d44,/* 32 bit Tx GMAC FIFO Almost Empty Thresh.*/ + TX_GMF_CTRL_T = 0x0d48,/* 32 bit Tx GMAC FIFO Control/Test */ + + TX_GMF_WP = 0x0d60,/* 32 bit Tx GMAC FIFO Write Pointer */ + TX_GMF_WSP = 0x0d64,/* 32 bit Tx GMAC FIFO Write Shadow Ptr. */ + TX_GMF_WLEV = 0x0d68,/* 32 bit Tx GMAC FIFO Write Level */ + + TX_GMF_RP = 0x0d70,/* 32 bit Tx GMAC FIFO Read Pointer */ + TX_GMF_RSTP = 0x0d74,/* 32 bit Tx GMAC FIFO Restart Pointer */ + TX_GMF_RLEV = 0x0d78,/* 32 bit Tx GMAC FIFO Read Level */ + + /* Threshold values for Yukon-EC Ultra and Extreme */ + ECU_AE_THR = 0x0070, /* Almost Empty Threshold */ + ECU_TXFF_LEV = 0x01a0, /* Tx BMU FIFO Level */ + ECU_JUMBO_WM = 0x0080, /* Jumbo Mode Watermark */ +}; + +/* Descriptor Poll Timer Registers */ +enum { + B28_DPT_INI = 0x0e00,/* 24 bit Descriptor Poll Timer Init Val */ + B28_DPT_VAL = 0x0e04,/* 24 bit Descriptor Poll Timer Curr Val */ + B28_DPT_CTRL = 0x0e08,/* 8 bit Descriptor Poll Timer Ctrl Reg */ + + B28_DPT_TST = 0x0e0a,/* 8 bit Descriptor Poll Timer Test Reg */ +}; + +/* Time Stamp Timer Registers (YUKON only) */ +enum { + GMAC_TI_ST_VAL = 0x0e14,/* 32 bit Time Stamp Timer Curr Val */ + GMAC_TI_ST_CTRL = 0x0e18,/* 8 bit Time Stamp Timer Ctrl Reg */ + GMAC_TI_ST_TST = 0x0e1a,/* 8 bit Time Stamp Timer Test Reg */ +}; + +/* Polling Unit Registers (Yukon-2 only) */ +enum { + POLL_CTRL = 0x0e20, /* 32 bit Polling Unit Control Reg */ + POLL_LAST_IDX = 0x0e24,/* 16 bit Polling Unit List Last Index */ + + POLL_LIST_ADDR_LO= 0x0e28,/* 32 bit Poll. List Start Addr (low) */ + POLL_LIST_ADDR_HI= 0x0e2c,/* 32 bit Poll. List Start Addr (high) */ +}; + +enum { + SMB_CFG = 0x0e40, /* 32 bit SMBus Config Register */ + SMB_CSR = 0x0e44, /* 32 bit SMBus Control/Status Register */ +}; + +enum { + CPU_WDOG = 0x0e48, /* 32 bit Watchdog Register */ + CPU_CNTR = 0x0e4C, /* 32 bit Counter Register */ + CPU_TIM = 0x0e50,/* 32 bit Timer Compare Register */ + CPU_AHB_ADDR = 0x0e54, /* 32 bit CPU AHB Debug Register */ + CPU_AHB_WDATA = 0x0e58, /* 32 bit CPU AHB Debug Register */ + CPU_AHB_RDATA = 0x0e5C, /* 32 bit CPU AHB Debug Register */ + HCU_MAP_BASE = 0x0e60, /* 32 bit Reset Mapping Base */ + CPU_AHB_CTRL = 0x0e64, /* 32 bit CPU AHB Debug Register */ + HCU_CCSR = 0x0e68, /* 32 bit CPU Control and Status Register */ + HCU_HCSR = 0x0e6C, /* 32 bit Host Control and Status Register */ +}; + +/* ASF Subsystem Registers (Yukon-2 only) */ +enum { + B28_Y2_SMB_CONFIG = 0x0e40,/* 32 bit ASF SMBus Config Register */ + B28_Y2_SMB_CSD_REG = 0x0e44,/* 32 bit ASF SMB Control/Status/Data */ + B28_Y2_ASF_IRQ_V_BASE=0x0e60,/* 32 bit ASF IRQ Vector Base */ + + B28_Y2_ASF_STAT_CMD= 0x0e68,/* 32 bit ASF Status and Command Reg */ + B28_Y2_ASF_HOST_COM= 0x0e6c,/* 32 bit ASF Host Communication Reg */ + B28_Y2_DATA_REG_1 = 0x0e70,/* 32 bit ASF/Host Data Register 1 */ + B28_Y2_DATA_REG_2 = 0x0e74,/* 32 bit ASF/Host Data Register 2 */ + B28_Y2_DATA_REG_3 = 0x0e78,/* 32 bit ASF/Host Data Register 3 */ + B28_Y2_DATA_REG_4 = 0x0e7c,/* 32 bit ASF/Host Data Register 4 */ +}; + +/* Status BMU Registers (Yukon-2 only)*/ +enum { + STAT_CTRL = 0x0e80,/* 32 bit Status BMU Control Reg */ + STAT_LAST_IDX = 0x0e84,/* 16 bit Status BMU Last Index */ + + STAT_LIST_ADDR_LO= 0x0e88,/* 32 bit Status List Start Addr (low) */ + STAT_LIST_ADDR_HI= 0x0e8c,/* 32 bit Status List Start Addr (high) */ + STAT_TXA1_RIDX = 0x0e90,/* 16 bit Status TxA1 Report Index Reg */ + STAT_TXS1_RIDX = 0x0e92,/* 16 bit Status TxS1 Report Index Reg */ + STAT_TXA2_RIDX = 0x0e94,/* 16 bit Status TxA2 Report Index Reg */ + STAT_TXS2_RIDX = 0x0e96,/* 16 bit Status TxS2 Report Index Reg */ + STAT_TX_IDX_TH = 0x0e98,/* 16 bit Status Tx Index Threshold Reg */ + STAT_PUT_IDX = 0x0e9c,/* 16 bit Status Put Index Reg */ + +/* FIFO Control/Status Registers (Yukon-2 only)*/ + STAT_FIFO_WP = 0x0ea0,/* 8 bit Status FIFO Write Pointer Reg */ + STAT_FIFO_RP = 0x0ea4,/* 8 bit Status FIFO Read Pointer Reg */ + STAT_FIFO_RSP = 0x0ea6,/* 8 bit Status FIFO Read Shadow Ptr */ + STAT_FIFO_LEVEL = 0x0ea8,/* 8 bit Status FIFO Level Reg */ + STAT_FIFO_SHLVL = 0x0eaa,/* 8 bit Status FIFO Shadow Level Reg */ + STAT_FIFO_WM = 0x0eac,/* 8 bit Status FIFO Watermark Reg */ + STAT_FIFO_ISR_WM= 0x0ead,/* 8 bit Status FIFO ISR Watermark Reg */ + +/* Level and ISR Timer Registers (Yukon-2 only)*/ + STAT_LEV_TIMER_INI= 0x0eb0,/* 32 bit Level Timer Init. Value Reg */ + STAT_LEV_TIMER_CNT= 0x0eb4,/* 32 bit Level Timer Counter Reg */ + STAT_LEV_TIMER_CTRL= 0x0eb8,/* 8 bit Level Timer Control Reg */ + STAT_LEV_TIMER_TEST= 0x0eb9,/* 8 bit Level Timer Test Reg */ + STAT_TX_TIMER_INI = 0x0ec0,/* 32 bit Tx Timer Init. Value Reg */ + STAT_TX_TIMER_CNT = 0x0ec4,/* 32 bit Tx Timer Counter Reg */ + STAT_TX_TIMER_CTRL = 0x0ec8,/* 8 bit Tx Timer Control Reg */ + STAT_TX_TIMER_TEST = 0x0ec9,/* 8 bit Tx Timer Test Reg */ + STAT_ISR_TIMER_INI = 0x0ed0,/* 32 bit ISR Timer Init. Value Reg */ + STAT_ISR_TIMER_CNT = 0x0ed4,/* 32 bit ISR Timer Counter Reg */ + STAT_ISR_TIMER_CTRL= 0x0ed8,/* 8 bit ISR Timer Control Reg */ + STAT_ISR_TIMER_TEST= 0x0ed9,/* 8 bit ISR Timer Test Reg */ +}; + +enum { + LINKLED_OFF = 0x01, + LINKLED_ON = 0x02, + LINKLED_LINKSYNC_OFF = 0x04, + LINKLED_LINKSYNC_ON = 0x08, + LINKLED_BLINK_OFF = 0x10, + LINKLED_BLINK_ON = 0x20, +}; + +/* GMAC and GPHY Control Registers (YUKON only) */ +enum { + GMAC_CTRL = 0x0f00,/* 32 bit GMAC Control Reg */ + GPHY_CTRL = 0x0f04,/* 32 bit GPHY Control Reg */ + GMAC_IRQ_SRC = 0x0f08,/* 8 bit GMAC Interrupt Source Reg */ + GMAC_IRQ_MSK = 0x0f0c,/* 8 bit GMAC Interrupt Mask Reg */ + GMAC_LINK_CTRL = 0x0f10,/* 16 bit Link Control Reg */ + +/* Wake-up Frame Pattern Match Control Registers (YUKON only) */ + WOL_CTRL_STAT = 0x0f20,/* 16 bit WOL Control/Status Reg */ + WOL_MATCH_CTL = 0x0f22,/* 8 bit WOL Match Control Reg */ + WOL_MATCH_RES = 0x0f23,/* 8 bit WOL Match Result Reg */ + WOL_MAC_ADDR = 0x0f24,/* 32 bit WOL MAC Address */ + WOL_PATT_RPTR = 0x0f2c,/* 8 bit WOL Pattern Read Pointer */ + +/* WOL Pattern Length Registers (YUKON only) */ + WOL_PATT_LEN_LO = 0x0f30,/* 32 bit WOL Pattern Length 3..0 */ + WOL_PATT_LEN_HI = 0x0f34,/* 24 bit WOL Pattern Length 6..4 */ + +/* WOL Pattern Counter Registers (YUKON only) */ + WOL_PATT_CNT_0 = 0x0f38,/* 32 bit WOL Pattern Counter 3..0 */ + WOL_PATT_CNT_4 = 0x0f3c,/* 24 bit WOL Pattern Counter 6..4 */ +}; +#define WOL_REGS(port, x) (x + (port)*0x80) + +enum { + WOL_PATT_RAM_1 = 0x1000,/* WOL Pattern RAM Link 1 */ + WOL_PATT_RAM_2 = 0x1400,/* WOL Pattern RAM Link 2 */ +}; +#define WOL_PATT_RAM_BASE(port) (WOL_PATT_RAM_1 + (port)*0x400) + +enum { + BASE_GMAC_1 = 0x2800,/* GMAC 1 registers */ + BASE_GMAC_2 = 0x3800,/* GMAC 2 registers */ +}; + +/* + * Marvel-PHY Registers, indirect addressed over GMAC + */ +enum { + PHY_MARV_CTRL = 0x00,/* 16 bit r/w PHY Control Register */ + PHY_MARV_STAT = 0x01,/* 16 bit r/o PHY Status Register */ + PHY_MARV_ID0 = 0x02,/* 16 bit r/o PHY ID0 Register */ + PHY_MARV_ID1 = 0x03,/* 16 bit r/o PHY ID1 Register */ + PHY_MARV_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */ + PHY_MARV_AUNE_LP = 0x05,/* 16 bit r/o Link Part Ability Reg */ + PHY_MARV_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */ + PHY_MARV_NEPG = 0x07,/* 16 bit r/w Next Page Register */ + PHY_MARV_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner */ + /* Marvel-specific registers */ + PHY_MARV_1000T_CTRL = 0x09,/* 16 bit r/w 1000Base-T Control Reg */ + PHY_MARV_1000T_STAT = 0x0a,/* 16 bit r/o 1000Base-T Status Reg */ + PHY_MARV_EXT_STAT = 0x0f,/* 16 bit r/o Extended Status Reg */ + PHY_MARV_PHY_CTRL = 0x10,/* 16 bit r/w PHY Specific Ctrl Reg */ + PHY_MARV_PHY_STAT = 0x11,/* 16 bit r/o PHY Specific Stat Reg */ + PHY_MARV_INT_MASK = 0x12,/* 16 bit r/w Interrupt Mask Reg */ + PHY_MARV_INT_STAT = 0x13,/* 16 bit r/o Interrupt Status Reg */ + PHY_MARV_EXT_CTRL = 0x14,/* 16 bit r/w Ext. PHY Specific Ctrl */ + PHY_MARV_RXE_CNT = 0x15,/* 16 bit r/w Receive Error Counter */ + PHY_MARV_EXT_ADR = 0x16,/* 16 bit r/w Ext. Ad. for Cable Diag. */ + PHY_MARV_PORT_IRQ = 0x17,/* 16 bit r/o Port 0 IRQ (88E1111 only) */ + PHY_MARV_LED_CTRL = 0x18,/* 16 bit r/w LED Control Reg */ + PHY_MARV_LED_OVER = 0x19,/* 16 bit r/w Manual LED Override Reg */ + PHY_MARV_EXT_CTRL_2 = 0x1a,/* 16 bit r/w Ext. PHY Specific Ctrl 2 */ + PHY_MARV_EXT_P_STAT = 0x1b,/* 16 bit r/w Ext. PHY Spec. Stat Reg */ + PHY_MARV_CABLE_DIAG = 0x1c,/* 16 bit r/o Cable Diagnostic Reg */ + PHY_MARV_PAGE_ADDR = 0x1d,/* 16 bit r/w Extended Page Address Reg */ + PHY_MARV_PAGE_DATA = 0x1e,/* 16 bit r/w Extended Page Data Reg */ + +/* for 10/100 Fast Ethernet PHY (88E3082 only) */ + PHY_MARV_FE_LED_PAR = 0x16,/* 16 bit r/w LED Parallel Select Reg. */ + PHY_MARV_FE_LED_SER = 0x17,/* 16 bit r/w LED Stream Select S. LED */ + PHY_MARV_FE_VCT_TX = 0x1a,/* 16 bit r/w VCT Reg. for TXP/N Pins */ + PHY_MARV_FE_VCT_RX = 0x1b,/* 16 bit r/o VCT Reg. for RXP/N Pins */ + PHY_MARV_FE_SPEC_2 = 0x1c,/* 16 bit r/w Specific Control Reg. 2 */ +}; + +enum { + PHY_CT_RESET = 1<<15, /* Bit 15: (sc) clear all PHY related regs */ + PHY_CT_LOOP = 1<<14, /* Bit 14: enable Loopback over PHY */ + PHY_CT_SPS_LSB = 1<<13, /* Bit 13: Speed select, lower bit */ + PHY_CT_ANE = 1<<12, /* Bit 12: Auto-Negotiation Enabled */ + PHY_CT_PDOWN = 1<<11, /* Bit 11: Power Down Mode */ + PHY_CT_ISOL = 1<<10, /* Bit 10: Isolate Mode */ + PHY_CT_RE_CFG = 1<<9, /* Bit 9: (sc) Restart Auto-Negotiation */ + PHY_CT_DUP_MD = 1<<8, /* Bit 8: Duplex Mode */ + PHY_CT_COL_TST = 1<<7, /* Bit 7: Collision Test enabled */ + PHY_CT_SPS_MSB = 1<<6, /* Bit 6: Speed select, upper bit */ +}; + +enum { + PHY_CT_SP1000 = PHY_CT_SPS_MSB, /* enable speed of 1000 Mbps */ + PHY_CT_SP100 = PHY_CT_SPS_LSB, /* enable speed of 100 Mbps */ + PHY_CT_SP10 = 0, /* enable speed of 10 Mbps */ +}; + +enum { + PHY_ST_EXT_ST = 1<<8, /* Bit 8: Extended Status Present */ + + PHY_ST_PRE_SUP = 1<<6, /* Bit 6: Preamble Suppression */ + PHY_ST_AN_OVER = 1<<5, /* Bit 5: Auto-Negotiation Over */ + PHY_ST_REM_FLT = 1<<4, /* Bit 4: Remote Fault Condition Occured */ + PHY_ST_AN_CAP = 1<<3, /* Bit 3: Auto-Negotiation Capability */ + PHY_ST_LSYNC = 1<<2, /* Bit 2: Link Synchronized */ + PHY_ST_JAB_DET = 1<<1, /* Bit 1: Jabber Detected */ + PHY_ST_EXT_REG = 1<<0, /* Bit 0: Extended Register available */ +}; + +enum { + PHY_I1_OUI_MSK = 0x3f<<10, /* Bit 15..10: Organization Unique ID */ + PHY_I1_MOD_NUM = 0x3f<<4, /* Bit 9.. 4: Model Number */ + PHY_I1_REV_MSK = 0xf, /* Bit 3.. 0: Revision Number */ +}; + +/* different Marvell PHY Ids */ +enum { + PHY_MARV_ID0_VAL= 0x0141, /* Marvell Unique Identifier */ + + PHY_BCOM_ID1_A1 = 0x6041, + PHY_BCOM_ID1_B2 = 0x6043, + PHY_BCOM_ID1_C0 = 0x6044, + PHY_BCOM_ID1_C5 = 0x6047, + + PHY_MARV_ID1_B0 = 0x0C23, /* Yukon (PHY 88E1011) */ + PHY_MARV_ID1_B2 = 0x0C25, /* Yukon-Plus (PHY 88E1011) */ + PHY_MARV_ID1_C2 = 0x0CC2, /* Yukon-EC (PHY 88E1111) */ + PHY_MARV_ID1_Y2 = 0x0C91, /* Yukon-2 (PHY 88E1112) */ + PHY_MARV_ID1_FE = 0x0C83, /* Yukon-FE (PHY 88E3082 Rev.A1) */ + PHY_MARV_ID1_ECU= 0x0CB0, /* Yukon-ECU (PHY 88E1149 Rev.B2?) */ +}; + +/* Advertisement register bits */ +enum { + PHY_AN_NXT_PG = 1<<15, /* Bit 15: Request Next Page */ + PHY_AN_ACK = 1<<14, /* Bit 14: (ro) Acknowledge Received */ + PHY_AN_RF = 1<<13, /* Bit 13: Remote Fault Bits */ + + PHY_AN_PAUSE_ASYM = 1<<11,/* Bit 11: Try for asymmetric */ + PHY_AN_PAUSE_CAP = 1<<10, /* Bit 10: Try for pause */ + PHY_AN_100BASE4 = 1<<9, /* Bit 9: Try for 100mbps 4k packets */ + PHY_AN_100FULL = 1<<8, /* Bit 8: Try for 100mbps full-duplex */ + PHY_AN_100HALF = 1<<7, /* Bit 7: Try for 100mbps half-duplex */ + PHY_AN_10FULL = 1<<6, /* Bit 6: Try for 10mbps full-duplex */ + PHY_AN_10HALF = 1<<5, /* Bit 5: Try for 10mbps half-duplex */ + PHY_AN_CSMA = 1<<0, /* Bit 0: Only selector supported */ + PHY_AN_SEL = 0x1f, /* Bit 4..0: Selector Field, 00001=Ethernet*/ + PHY_AN_FULL = PHY_AN_100FULL | PHY_AN_10FULL | PHY_AN_CSMA, + PHY_AN_ALL = PHY_AN_10HALF | PHY_AN_10FULL | + PHY_AN_100HALF | PHY_AN_100FULL, +}; + +/***** PHY_BCOM_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/ +/***** PHY_MARV_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/ +enum { + PHY_B_1000S_MSF = 1<<15, /* Bit 15: Master/Slave Fault */ + PHY_B_1000S_MSR = 1<<14, /* Bit 14: Master/Slave Result */ + PHY_B_1000S_LRS = 1<<13, /* Bit 13: Local Receiver Status */ + PHY_B_1000S_RRS = 1<<12, /* Bit 12: Remote Receiver Status */ + PHY_B_1000S_LP_FD = 1<<11, /* Bit 11: Link Partner can FD */ + PHY_B_1000S_LP_HD = 1<<10, /* Bit 10: Link Partner can HD */ + /* Bit 9..8: reserved */ + PHY_B_1000S_IEC = 0xff, /* Bit 7..0: Idle Error Count */ +}; + +/** Marvell-Specific */ +enum { + PHY_M_AN_NXT_PG = 1<<15, /* Request Next Page */ + PHY_M_AN_ACK = 1<<14, /* (ro) Acknowledge Received */ + PHY_M_AN_RF = 1<<13, /* Remote Fault */ + + PHY_M_AN_ASP = 1<<11, /* Asymmetric Pause */ + PHY_M_AN_PC = 1<<10, /* MAC Pause implemented */ + PHY_M_AN_100_T4 = 1<<9, /* Not cap. 100Base-T4 (always 0) */ + PHY_M_AN_100_FD = 1<<8, /* Advertise 100Base-TX Full Duplex */ + PHY_M_AN_100_HD = 1<<7, /* Advertise 100Base-TX Half Duplex */ + PHY_M_AN_10_FD = 1<<6, /* Advertise 10Base-TX Full Duplex */ + PHY_M_AN_10_HD = 1<<5, /* Advertise 10Base-TX Half Duplex */ + PHY_M_AN_SEL_MSK =0x1f<<4, /* Bit 4.. 0: Selector Field Mask */ +}; + +/* special defines for FIBER (88E1011S only) */ +enum { + PHY_M_AN_ASP_X = 1<<8, /* Asymmetric Pause */ + PHY_M_AN_PC_X = 1<<7, /* MAC Pause implemented */ + PHY_M_AN_1000X_AHD = 1<<6, /* Advertise 10000Base-X Half Duplex */ + PHY_M_AN_1000X_AFD = 1<<5, /* Advertise 10000Base-X Full Duplex */ +}; + +/* Pause Bits (PHY_M_AN_ASP_X and PHY_M_AN_PC_X) encoding */ +enum { + PHY_M_P_NO_PAUSE_X = 0<<7,/* Bit 8.. 7: no Pause Mode */ + PHY_M_P_SYM_MD_X = 1<<7, /* Bit 8.. 7: symmetric Pause Mode */ + PHY_M_P_ASYM_MD_X = 2<<7,/* Bit 8.. 7: asymmetric Pause Mode */ + PHY_M_P_BOTH_MD_X = 3<<7,/* Bit 8.. 7: both Pause Mode */ +}; + +/***** PHY_MARV_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/ +enum { + PHY_M_1000C_TEST = 7<<13,/* Bit 15..13: Test Modes */ + PHY_M_1000C_MSE = 1<<12, /* Manual Master/Slave Enable */ + PHY_M_1000C_MSC = 1<<11, /* M/S Configuration (1=Master) */ + PHY_M_1000C_MPD = 1<<10, /* Multi-Port Device */ + PHY_M_1000C_AFD = 1<<9, /* Advertise Full Duplex */ + PHY_M_1000C_AHD = 1<<8, /* Advertise Half Duplex */ +}; + +/***** PHY_MARV_PHY_CTRL 16 bit r/w PHY Specific Ctrl Reg *****/ +enum { + PHY_M_PC_TX_FFD_MSK = 3<<14,/* Bit 15..14: Tx FIFO Depth Mask */ + PHY_M_PC_RX_FFD_MSK = 3<<12,/* Bit 13..12: Rx FIFO Depth Mask */ + PHY_M_PC_ASS_CRS_TX = 1<<11, /* Assert CRS on Transmit */ + PHY_M_PC_FL_GOOD = 1<<10, /* Force Link Good */ + PHY_M_PC_EN_DET_MSK = 3<<8,/* Bit 9.. 8: Energy Detect Mask */ + PHY_M_PC_ENA_EXT_D = 1<<7, /* Enable Ext. Distance (10BT) */ + PHY_M_PC_MDIX_MSK = 3<<5,/* Bit 6.. 5: MDI/MDIX Config. Mask */ + PHY_M_PC_DIS_125CLK = 1<<4, /* Disable 125 CLK */ + PHY_M_PC_MAC_POW_UP = 1<<3, /* MAC Power up */ + PHY_M_PC_SQE_T_ENA = 1<<2, /* SQE Test Enabled */ + PHY_M_PC_POL_R_DIS = 1<<1, /* Polarity Reversal Disabled */ + PHY_M_PC_DIS_JABBER = 1<<0, /* Disable Jabber */ +}; + +enum { + PHY_M_PC_EN_DET = 2<<8, /* Energy Detect (Mode 1) */ + PHY_M_PC_EN_DET_PLUS = 3<<8, /* Energy Detect Plus (Mode 2) */ +}; + +#define PHY_M_PC_MDI_XMODE(x) (((u16)(x)<<5) & PHY_M_PC_MDIX_MSK) + +enum { + PHY_M_PC_MAN_MDI = 0, /* 00 = Manual MDI configuration */ + PHY_M_PC_MAN_MDIX = 1, /* 01 = Manual MDIX configuration */ + PHY_M_PC_ENA_AUTO = 3, /* 11 = Enable Automatic Crossover */ +}; + +/* for Yukon-EC Ultra Gigabit Ethernet PHY (88E1149 only) */ +enum { + PHY_M_PC_COP_TX_DIS = 1<<3, /* Copper Transmitter Disable */ + PHY_M_PC_POW_D_ENA = 1<<2, /* Power Down Enable */ +}; + +/* for 10/100 Fast Ethernet PHY (88E3082 only) */ +enum { + PHY_M_PC_ENA_DTE_DT = 1<<15, /* Enable Data Terminal Equ. (DTE) Detect */ + PHY_M_PC_ENA_ENE_DT = 1<<14, /* Enable Energy Detect (sense & pulse) */ + PHY_M_PC_DIS_NLP_CK = 1<<13, /* Disable Normal Link Puls (NLP) Check */ + PHY_M_PC_ENA_LIP_NP = 1<<12, /* Enable Link Partner Next Page Reg. */ + PHY_M_PC_DIS_NLP_GN = 1<<11, /* Disable Normal Link Puls Generation */ + + PHY_M_PC_DIS_SCRAMB = 1<<9, /* Disable Scrambler */ + PHY_M_PC_DIS_FEFI = 1<<8, /* Disable Far End Fault Indic. (FEFI) */ + + PHY_M_PC_SH_TP_SEL = 1<<6, /* Shielded Twisted Pair Select */ + PHY_M_PC_RX_FD_MSK = 3<<2,/* Bit 3.. 2: Rx FIFO Depth Mask */ +}; + +/***** PHY_MARV_PHY_STAT 16 bit r/o PHY Specific Status Reg *****/ +enum { + PHY_M_PS_SPEED_MSK = 3<<14, /* Bit 15..14: Speed Mask */ + PHY_M_PS_SPEED_1000 = 1<<15, /* 10 = 1000 Mbps */ + PHY_M_PS_SPEED_100 = 1<<14, /* 01 = 100 Mbps */ + PHY_M_PS_SPEED_10 = 0, /* 00 = 10 Mbps */ + PHY_M_PS_FULL_DUP = 1<<13, /* Full Duplex */ + PHY_M_PS_PAGE_REC = 1<<12, /* Page Received */ + PHY_M_PS_SPDUP_RES = 1<<11, /* Speed & Duplex Resolved */ + PHY_M_PS_LINK_UP = 1<<10, /* Link Up */ + PHY_M_PS_CABLE_MSK = 7<<7, /* Bit 9.. 7: Cable Length Mask */ + PHY_M_PS_MDI_X_STAT = 1<<6, /* MDI Crossover Stat (1=MDIX) */ + PHY_M_PS_DOWNS_STAT = 1<<5, /* Downshift Status (1=downsh.) */ + PHY_M_PS_ENDET_STAT = 1<<4, /* Energy Detect Status (1=act) */ + PHY_M_PS_TX_P_EN = 1<<3, /* Tx Pause Enabled */ + PHY_M_PS_RX_P_EN = 1<<2, /* Rx Pause Enabled */ + PHY_M_PS_POL_REV = 1<<1, /* Polarity Reversed */ + PHY_M_PS_JABBER = 1<<0, /* Jabber */ +}; + +#define PHY_M_PS_PAUSE_MSK (PHY_M_PS_TX_P_EN | PHY_M_PS_RX_P_EN) + +/* for 10/100 Fast Ethernet PHY (88E3082 only) */ +enum { + PHY_M_PS_DTE_DETECT = 1<<15, /* Data Terminal Equipment (DTE) Detected */ + PHY_M_PS_RES_SPEED = 1<<14, /* Resolved Speed (1=100 Mbps, 0=10 Mbps */ +}; + +enum { + PHY_M_IS_AN_ERROR = 1<<15, /* Auto-Negotiation Error */ + PHY_M_IS_LSP_CHANGE = 1<<14, /* Link Speed Changed */ + PHY_M_IS_DUP_CHANGE = 1<<13, /* Duplex Mode Changed */ + PHY_M_IS_AN_PR = 1<<12, /* Page Received */ + PHY_M_IS_AN_COMPL = 1<<11, /* Auto-Negotiation Completed */ + PHY_M_IS_LST_CHANGE = 1<<10, /* Link Status Changed */ + PHY_M_IS_SYMB_ERROR = 1<<9, /* Symbol Error */ + PHY_M_IS_FALSE_CARR = 1<<8, /* False Carrier */ + PHY_M_IS_FIFO_ERROR = 1<<7, /* FIFO Overflow/Underrun Error */ + PHY_M_IS_MDI_CHANGE = 1<<6, /* MDI Crossover Changed */ + PHY_M_IS_DOWNSH_DET = 1<<5, /* Downshift Detected */ + PHY_M_IS_END_CHANGE = 1<<4, /* Energy Detect Changed */ + + PHY_M_IS_DTE_CHANGE = 1<<2, /* DTE Power Det. Status Changed */ + PHY_M_IS_POL_CHANGE = 1<<1, /* Polarity Changed */ + PHY_M_IS_JABBER = 1<<0, /* Jabber */ + + PHY_M_DEF_MSK = PHY_M_IS_LSP_CHANGE | PHY_M_IS_LST_CHANGE + | PHY_M_IS_DUP_CHANGE, + PHY_M_AN_MSK = PHY_M_IS_AN_ERROR | PHY_M_IS_AN_COMPL, +}; + + +/***** PHY_MARV_EXT_CTRL 16 bit r/w Ext. PHY Specific Ctrl *****/ +enum { + PHY_M_EC_ENA_BC_EXT = 1<<15, /* Enable Block Carr. Ext. (88E1111 only) */ + PHY_M_EC_ENA_LIN_LB = 1<<14, /* Enable Line Loopback (88E1111 only) */ + + PHY_M_EC_DIS_LINK_P = 1<<12, /* Disable Link Pulses (88E1111 only) */ + PHY_M_EC_M_DSC_MSK = 3<<10, /* Bit 11..10: Master Downshift Counter */ + /* (88E1011 only) */ + PHY_M_EC_S_DSC_MSK = 3<<8,/* Bit 9.. 8: Slave Downshift Counter */ + /* (88E1011 only) */ + PHY_M_EC_M_DSC_MSK2 = 7<<9,/* Bit 11.. 9: Master Downshift Counter */ + /* (88E1111 only) */ + PHY_M_EC_DOWN_S_ENA = 1<<8, /* Downshift Enable (88E1111 only) */ + /* !!! Errata in spec. (1 = disable) */ + PHY_M_EC_RX_TIM_CT = 1<<7, /* RGMII Rx Timing Control*/ + PHY_M_EC_MAC_S_MSK = 7<<4,/* Bit 6.. 4: Def. MAC interface speed */ + PHY_M_EC_FIB_AN_ENA = 1<<3, /* Fiber Auto-Neg. Enable (88E1011S only) */ + PHY_M_EC_DTE_D_ENA = 1<<2, /* DTE Detect Enable (88E1111 only) */ + PHY_M_EC_TX_TIM_CT = 1<<1, /* RGMII Tx Timing Control */ + PHY_M_EC_TRANS_DIS = 1<<0, /* Transmitter Disable (88E1111 only) */}; + +#define PHY_M_EC_M_DSC(x) ((u16)(x)<<10 & PHY_M_EC_M_DSC_MSK) + /* 00=1x; 01=2x; 10=3x; 11=4x */ +#define PHY_M_EC_S_DSC(x) ((u16)(x)<<8 & PHY_M_EC_S_DSC_MSK) + /* 00=dis; 01=1x; 10=2x; 11=3x */ +#define PHY_M_EC_DSC_2(x) ((u16)(x)<<9 & PHY_M_EC_M_DSC_MSK2) + /* 000=1x; 001=2x; 010=3x; 011=4x */ +#define PHY_M_EC_MAC_S(x) ((u16)(x)<<4 & PHY_M_EC_MAC_S_MSK) + /* 01X=0; 110=2.5; 111=25 (MHz) */ + +/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */ +enum { + PHY_M_PC_DIS_LINK_Pa = 1<<15,/* Disable Link Pulses */ + PHY_M_PC_DSC_MSK = 7<<12,/* Bit 14..12: Downshift Counter */ + PHY_M_PC_DOWN_S_ENA = 1<<11,/* Downshift Enable */ +}; +/* !!! Errata in spec. (1 = disable) */ + +#define PHY_M_PC_DSC(x) (((u16)(x)<<12) & PHY_M_PC_DSC_MSK) + /* 100=5x; 101=6x; 110=7x; 111=8x */ +enum { + MAC_TX_CLK_0_MHZ = 2, + MAC_TX_CLK_2_5_MHZ = 6, + MAC_TX_CLK_25_MHZ = 7, +}; + +/***** PHY_MARV_LED_CTRL 16 bit r/w LED Control Reg *****/ +enum { + PHY_M_LEDC_DIS_LED = 1<<15, /* Disable LED */ + PHY_M_LEDC_PULS_MSK = 7<<12,/* Bit 14..12: Pulse Stretch Mask */ + PHY_M_LEDC_F_INT = 1<<11, /* Force Interrupt */ + PHY_M_LEDC_BL_R_MSK = 7<<8,/* Bit 10.. 8: Blink Rate Mask */ + PHY_M_LEDC_DP_C_LSB = 1<<7, /* Duplex Control (LSB, 88E1111 only) */ + PHY_M_LEDC_TX_C_LSB = 1<<6, /* Tx Control (LSB, 88E1111 only) */ + PHY_M_LEDC_LK_C_MSK = 7<<3,/* Bit 5.. 3: Link Control Mask */ + /* (88E1111 only) */ +}; + +enum { + PHY_M_LEDC_LINK_MSK = 3<<3,/* Bit 4.. 3: Link Control Mask */ + /* (88E1011 only) */ + PHY_M_LEDC_DP_CTRL = 1<<2, /* Duplex Control */ + PHY_M_LEDC_DP_C_MSB = 1<<2, /* Duplex Control (MSB, 88E1111 only) */ + PHY_M_LEDC_RX_CTRL = 1<<1, /* Rx Activity / Link */ + PHY_M_LEDC_TX_CTRL = 1<<0, /* Tx Activity / Link */ + PHY_M_LEDC_TX_C_MSB = 1<<0, /* Tx Control (MSB, 88E1111 only) */ +}; + +#define PHY_M_LED_PULS_DUR(x) (((u16)(x)<<12) & PHY_M_LEDC_PULS_MSK) + +/***** PHY_MARV_PHY_STAT (page 3)16 bit r/w Polarity Control Reg. *****/ +enum { + PHY_M_POLC_LS1M_MSK = 0xf<<12, /* Bit 15..12: LOS,STAT1 Mix % Mask */ + PHY_M_POLC_IS0M_MSK = 0xf<<8, /* Bit 11.. 8: INIT,STAT0 Mix % Mask */ + PHY_M_POLC_LOS_MSK = 0x3<<6, /* Bit 7.. 6: LOS Pol. Ctrl. Mask */ + PHY_M_POLC_INIT_MSK = 0x3<<4, /* Bit 5.. 4: INIT Pol. Ctrl. Mask */ + PHY_M_POLC_STA1_MSK = 0x3<<2, /* Bit 3.. 2: STAT1 Pol. Ctrl. Mask */ + PHY_M_POLC_STA0_MSK = 0x3, /* Bit 1.. 0: STAT0 Pol. Ctrl. Mask */ +}; + +#define PHY_M_POLC_LS1_P_MIX(x) (((x)<<12) & PHY_M_POLC_LS1M_MSK) +#define PHY_M_POLC_IS0_P_MIX(x) (((x)<<8) & PHY_M_POLC_IS0M_MSK) +#define PHY_M_POLC_LOS_CTRL(x) (((x)<<6) & PHY_M_POLC_LOS_MSK) +#define PHY_M_POLC_INIT_CTRL(x) (((x)<<4) & PHY_M_POLC_INIT_MSK) +#define PHY_M_POLC_STA1_CTRL(x) (((x)<<2) & PHY_M_POLC_STA1_MSK) +#define PHY_M_POLC_STA0_CTRL(x) (((x)<<0) & PHY_M_POLC_STA0_MSK) + +enum { + PULS_NO_STR = 0,/* no pulse stretching */ + PULS_21MS = 1,/* 21 ms to 42 ms */ + PULS_42MS = 2,/* 42 ms to 84 ms */ + PULS_84MS = 3,/* 84 ms to 170 ms */ + PULS_170MS = 4,/* 170 ms to 340 ms */ + PULS_340MS = 5,/* 340 ms to 670 ms */ + PULS_670MS = 6,/* 670 ms to 1.3 s */ + PULS_1300MS = 7,/* 1.3 s to 2.7 s */ +}; + +#define PHY_M_LED_BLINK_RT(x) (((u16)(x)<<8) & PHY_M_LEDC_BL_R_MSK) + +enum { + BLINK_42MS = 0,/* 42 ms */ + BLINK_84MS = 1,/* 84 ms */ + BLINK_170MS = 2,/* 170 ms */ + BLINK_340MS = 3,/* 340 ms */ + BLINK_670MS = 4,/* 670 ms */ +}; + +/***** PHY_MARV_LED_OVER 16 bit r/w Manual LED Override Reg *****/ +#define PHY_M_LED_MO_SGMII(x) ((x)<<14) /* Bit 15..14: SGMII AN Timer */ + +#define PHY_M_LED_MO_DUP(x) ((x)<<10) /* Bit 11..10: Duplex */ +#define PHY_M_LED_MO_10(x) ((x)<<8) /* Bit 9.. 8: Link 10 */ +#define PHY_M_LED_MO_100(x) ((x)<<6) /* Bit 7.. 6: Link 100 */ +#define PHY_M_LED_MO_1000(x) ((x)<<4) /* Bit 5.. 4: Link 1000 */ +#define PHY_M_LED_MO_RX(x) ((x)<<2) /* Bit 3.. 2: Rx */ +#define PHY_M_LED_MO_TX(x) ((x)<<0) /* Bit 1.. 0: Tx */ + +enum led_mode { + MO_LED_NORM = 0, + MO_LED_BLINK = 1, + MO_LED_OFF = 2, + MO_LED_ON = 3, +}; + +/***** PHY_MARV_EXT_CTRL_2 16 bit r/w Ext. PHY Specific Ctrl 2 *****/ +enum { + PHY_M_EC2_FI_IMPED = 1<<6, /* Fiber Input Impedance */ + PHY_M_EC2_FO_IMPED = 1<<5, /* Fiber Output Impedance */ + PHY_M_EC2_FO_M_CLK = 1<<4, /* Fiber Mode Clock Enable */ + PHY_M_EC2_FO_BOOST = 1<<3, /* Fiber Output Boost */ + PHY_M_EC2_FO_AM_MSK = 7,/* Bit 2.. 0: Fiber Output Amplitude */ +}; + +/***** PHY_MARV_EXT_P_STAT 16 bit r/w Ext. PHY Specific Status *****/ +enum { + PHY_M_FC_AUTO_SEL = 1<<15, /* Fiber/Copper Auto Sel. Dis. */ + PHY_M_FC_AN_REG_ACC = 1<<14, /* Fiber/Copper AN Reg. Access */ + PHY_M_FC_RESOLUTION = 1<<13, /* Fiber/Copper Resolution */ + PHY_M_SER_IF_AN_BP = 1<<12, /* Ser. IF AN Bypass Enable */ + PHY_M_SER_IF_BP_ST = 1<<11, /* Ser. IF AN Bypass Status */ + PHY_M_IRQ_POLARITY = 1<<10, /* IRQ polarity */ + PHY_M_DIS_AUT_MED = 1<<9, /* Disable Aut. Medium Reg. Selection */ + /* (88E1111 only) */ + + PHY_M_UNDOC1 = 1<<7, /* undocumented bit !! */ + PHY_M_DTE_POW_STAT = 1<<4, /* DTE Power Status (88E1111 only) */ + PHY_M_MODE_MASK = 0xf, /* Bit 3.. 0: copy of HWCFG MODE[3:0] */ +}; + +/* for 10/100 Fast Ethernet PHY (88E3082 only) */ +/***** PHY_MARV_FE_LED_PAR 16 bit r/w LED Parallel Select Reg. *****/ + /* Bit 15..12: reserved (used internally) */ +enum { + PHY_M_FELP_LED2_MSK = 0xf<<8, /* Bit 11.. 8: LED2 Mask (LINK) */ + PHY_M_FELP_LED1_MSK = 0xf<<4, /* Bit 7.. 4: LED1 Mask (ACT) */ + PHY_M_FELP_LED0_MSK = 0xf, /* Bit 3.. 0: LED0 Mask (SPEED) */ +}; + +#define PHY_M_FELP_LED2_CTRL(x) (((u16)(x)<<8) & PHY_M_FELP_LED2_MSK) +#define PHY_M_FELP_LED1_CTRL(x) (((u16)(x)<<4) & PHY_M_FELP_LED1_MSK) +#define PHY_M_FELP_LED0_CTRL(x) (((u16)(x)<<0) & PHY_M_FELP_LED0_MSK) + +enum { + LED_PAR_CTRL_COLX = 0x00, + LED_PAR_CTRL_ERROR = 0x01, + LED_PAR_CTRL_DUPLEX = 0x02, + LED_PAR_CTRL_DP_COL = 0x03, + LED_PAR_CTRL_SPEED = 0x04, + LED_PAR_CTRL_LINK = 0x05, + LED_PAR_CTRL_TX = 0x06, + LED_PAR_CTRL_RX = 0x07, + LED_PAR_CTRL_ACT = 0x08, + LED_PAR_CTRL_LNK_RX = 0x09, + LED_PAR_CTRL_LNK_AC = 0x0a, + LED_PAR_CTRL_ACT_BL = 0x0b, + LED_PAR_CTRL_TX_BL = 0x0c, + LED_PAR_CTRL_RX_BL = 0x0d, + LED_PAR_CTRL_COL_BL = 0x0e, + LED_PAR_CTRL_INACT = 0x0f +}; + +/*****,PHY_MARV_FE_SPEC_2 16 bit r/w Specific Control Reg. 2 *****/ +enum { + PHY_M_FESC_DIS_WAIT = 1<<2, /* Disable TDR Waiting Period */ + PHY_M_FESC_ENA_MCLK = 1<<1, /* Enable MAC Rx Clock in sleep mode */ + PHY_M_FESC_SEL_CL_A = 1<<0, /* Select Class A driver (100B-TX) */ +}; + +/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */ +/***** PHY_MARV_PHY_CTRL (page 1) 16 bit r/w Fiber Specific Ctrl *****/ +enum { + PHY_M_FIB_FORCE_LNK = 1<<10,/* Force Link Good */ + PHY_M_FIB_SIGD_POL = 1<<9, /* SIGDET Polarity */ + PHY_M_FIB_TX_DIS = 1<<3, /* Transmitter Disable */ +}; + +/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */ +/***** PHY_MARV_PHY_CTRL (page 2) 16 bit r/w MAC Specific Ctrl *****/ +enum { + PHY_M_MAC_MD_MSK = 7<<7, /* Bit 9.. 7: Mode Select Mask */ + PHY_M_MAC_GMIF_PUP = 1<<3, /* GMII Power Up (88E1149 only) */ + PHY_M_MAC_MD_AUTO = 3,/* Auto Copper/1000Base-X */ + PHY_M_MAC_MD_COPPER = 5,/* Copper only */ + PHY_M_MAC_MD_1000BX = 7,/* 1000Base-X only */ +}; +#define PHY_M_MAC_MODE_SEL(x) (((x)<<7) & PHY_M_MAC_MD_MSK) + +/***** PHY_MARV_PHY_CTRL (page 3) 16 bit r/w LED Control Reg. *****/ +enum { + PHY_M_LEDC_LOS_MSK = 0xf<<12,/* Bit 15..12: LOS LED Ctrl. Mask */ + PHY_M_LEDC_INIT_MSK = 0xf<<8, /* Bit 11.. 8: INIT LED Ctrl. Mask */ + PHY_M_LEDC_STA1_MSK = 0xf<<4,/* Bit 7.. 4: STAT1 LED Ctrl. Mask */ + PHY_M_LEDC_STA0_MSK = 0xf, /* Bit 3.. 0: STAT0 LED Ctrl. Mask */ +}; + +#define PHY_M_LEDC_LOS_CTRL(x) (((x)<<12) & PHY_M_LEDC_LOS_MSK) +#define PHY_M_LEDC_INIT_CTRL(x) (((x)<<8) & PHY_M_LEDC_INIT_MSK) +#define PHY_M_LEDC_STA1_CTRL(x) (((x)<<4) & PHY_M_LEDC_STA1_MSK) +#define PHY_M_LEDC_STA0_CTRL(x) (((x)<<0) & PHY_M_LEDC_STA0_MSK) + +/* GMAC registers */ +/* Port Registers */ +enum { + GM_GP_STAT = 0x0000, /* 16 bit r/o General Purpose Status */ + GM_GP_CTRL = 0x0004, /* 16 bit r/w General Purpose Control */ + GM_TX_CTRL = 0x0008, /* 16 bit r/w Transmit Control Reg. */ + GM_RX_CTRL = 0x000c, /* 16 bit r/w Receive Control Reg. */ + GM_TX_FLOW_CTRL = 0x0010, /* 16 bit r/w Transmit Flow-Control */ + GM_TX_PARAM = 0x0014, /* 16 bit r/w Transmit Parameter Reg. */ + GM_SERIAL_MODE = 0x0018, /* 16 bit r/w Serial Mode Register */ +/* Source Address Registers */ + GM_SRC_ADDR_1L = 0x001c, /* 16 bit r/w Source Address 1 (low) */ + GM_SRC_ADDR_1M = 0x0020, /* 16 bit r/w Source Address 1 (middle) */ + GM_SRC_ADDR_1H = 0x0024, /* 16 bit r/w Source Address 1 (high) */ + GM_SRC_ADDR_2L = 0x0028, /* 16 bit r/w Source Address 2 (low) */ + GM_SRC_ADDR_2M = 0x002c, /* 16 bit r/w Source Address 2 (middle) */ + GM_SRC_ADDR_2H = 0x0030, /* 16 bit r/w Source Address 2 (high) */ + +/* Multicast Address Hash Registers */ + GM_MC_ADDR_H1 = 0x0034, /* 16 bit r/w Multicast Address Hash 1 */ + GM_MC_ADDR_H2 = 0x0038, /* 16 bit r/w Multicast Address Hash 2 */ + GM_MC_ADDR_H3 = 0x003c, /* 16 bit r/w Multicast Address Hash 3 */ + GM_MC_ADDR_H4 = 0x0040, /* 16 bit r/w Multicast Address Hash 4 */ + +/* Interrupt Source Registers */ + GM_TX_IRQ_SRC = 0x0044, /* 16 bit r/o Tx Overflow IRQ Source */ + GM_RX_IRQ_SRC = 0x0048, /* 16 bit r/o Rx Overflow IRQ Source */ + GM_TR_IRQ_SRC = 0x004c, /* 16 bit r/o Tx/Rx Over. IRQ Source */ + +/* Interrupt Mask Registers */ + GM_TX_IRQ_MSK = 0x0050, /* 16 bit r/w Tx Overflow IRQ Mask */ + GM_RX_IRQ_MSK = 0x0054, /* 16 bit r/w Rx Overflow IRQ Mask */ + GM_TR_IRQ_MSK = 0x0058, /* 16 bit r/w Tx/Rx Over. IRQ Mask */ + +/* Serial Management Interface (SMI) Registers */ + GM_SMI_CTRL = 0x0080, /* 16 bit r/w SMI Control Register */ + GM_SMI_DATA = 0x0084, /* 16 bit r/w SMI Data Register */ + GM_PHY_ADDR = 0x0088, /* 16 bit r/w GPHY Address Register */ +/* MIB Counters */ + GM_MIB_CNT_BASE = 0x0100, /* Base Address of MIB Counters */ + GM_MIB_CNT_END = 0x025C, /* Last MIB counter */ +}; + + +/* + * MIB Counters base address definitions (low word) - + * use offset 4 for access to high word (32 bit r/o) + */ +enum { + GM_RXF_UC_OK = GM_MIB_CNT_BASE + 0, /* Unicast Frames Received OK */ + GM_RXF_BC_OK = GM_MIB_CNT_BASE + 8, /* Broadcast Frames Received OK */ + GM_RXF_MPAUSE = GM_MIB_CNT_BASE + 16, /* Pause MAC Ctrl Frames Received */ + GM_RXF_MC_OK = GM_MIB_CNT_BASE + 24, /* Multicast Frames Received OK */ + GM_RXF_FCS_ERR = GM_MIB_CNT_BASE + 32, /* Rx Frame Check Seq. Error */ + + GM_RXO_OK_LO = GM_MIB_CNT_BASE + 48, /* Octets Received OK Low */ + GM_RXO_OK_HI = GM_MIB_CNT_BASE + 56, /* Octets Received OK High */ + GM_RXO_ERR_LO = GM_MIB_CNT_BASE + 64, /* Octets Received Invalid Low */ + GM_RXO_ERR_HI = GM_MIB_CNT_BASE + 72, /* Octets Received Invalid High */ + GM_RXF_SHT = GM_MIB_CNT_BASE + 80, /* Frames <64 Byte Received OK */ + GM_RXE_FRAG = GM_MIB_CNT_BASE + 88, /* Frames <64 Byte Received with FCS Err */ + GM_RXF_64B = GM_MIB_CNT_BASE + 96, /* 64 Byte Rx Frame */ + GM_RXF_127B = GM_MIB_CNT_BASE + 104,/* 65-127 Byte Rx Frame */ + GM_RXF_255B = GM_MIB_CNT_BASE + 112,/* 128-255 Byte Rx Frame */ + GM_RXF_511B = GM_MIB_CNT_BASE + 120,/* 256-511 Byte Rx Frame */ + GM_RXF_1023B = GM_MIB_CNT_BASE + 128,/* 512-1023 Byte Rx Frame */ + GM_RXF_1518B = GM_MIB_CNT_BASE + 136,/* 1024-1518 Byte Rx Frame */ + GM_RXF_MAX_SZ = GM_MIB_CNT_BASE + 144,/* 1519-MaxSize Byte Rx Frame */ + GM_RXF_LNG_ERR = GM_MIB_CNT_BASE + 152,/* Rx Frame too Long Error */ + GM_RXF_JAB_PKT = GM_MIB_CNT_BASE + 160,/* Rx Jabber Packet Frame */ + + GM_RXE_FIFO_OV = GM_MIB_CNT_BASE + 176,/* Rx FIFO overflow Event */ + GM_TXF_UC_OK = GM_MIB_CNT_BASE + 192,/* Unicast Frames Xmitted OK */ + GM_TXF_BC_OK = GM_MIB_CNT_BASE + 200,/* Broadcast Frames Xmitted OK */ + GM_TXF_MPAUSE = GM_MIB_CNT_BASE + 208,/* Pause MAC Ctrl Frames Xmitted */ + GM_TXF_MC_OK = GM_MIB_CNT_BASE + 216,/* Multicast Frames Xmitted OK */ + GM_TXO_OK_LO = GM_MIB_CNT_BASE + 224,/* Octets Transmitted OK Low */ + GM_TXO_OK_HI = GM_MIB_CNT_BASE + 232,/* Octets Transmitted OK High */ + GM_TXF_64B = GM_MIB_CNT_BASE + 240,/* 64 Byte Tx Frame */ + GM_TXF_127B = GM_MIB_CNT_BASE + 248,/* 65-127 Byte Tx Frame */ + GM_TXF_255B = GM_MIB_CNT_BASE + 256,/* 128-255 Byte Tx Frame */ + GM_TXF_511B = GM_MIB_CNT_BASE + 264,/* 256-511 Byte Tx Frame */ + GM_TXF_1023B = GM_MIB_CNT_BASE + 272,/* 512-1023 Byte Tx Frame */ + GM_TXF_1518B = GM_MIB_CNT_BASE + 280,/* 1024-1518 Byte Tx Frame */ + GM_TXF_MAX_SZ = GM_MIB_CNT_BASE + 288,/* 1519-MaxSize Byte Tx Frame */ + + GM_TXF_COL = GM_MIB_CNT_BASE + 304,/* Tx Collision */ + GM_TXF_LAT_COL = GM_MIB_CNT_BASE + 312,/* Tx Late Collision */ + GM_TXF_ABO_COL = GM_MIB_CNT_BASE + 320,/* Tx aborted due to Exces. Col. */ + GM_TXF_MUL_COL = GM_MIB_CNT_BASE + 328,/* Tx Multiple Collision */ + GM_TXF_SNG_COL = GM_MIB_CNT_BASE + 336,/* Tx Single Collision */ + GM_TXE_FIFO_UR = GM_MIB_CNT_BASE + 344,/* Tx FIFO Underrun Event */ +}; + +/* GMAC Bit Definitions */ +/* GM_GP_STAT 16 bit r/o General Purpose Status Register */ +enum { + GM_GPSR_SPEED = 1<<15, /* Bit 15: Port Speed (1 = 100 Mbps) */ + GM_GPSR_DUPLEX = 1<<14, /* Bit 14: Duplex Mode (1 = Full) */ + GM_GPSR_FC_TX_DIS = 1<<13, /* Bit 13: Tx Flow-Control Mode Disabled */ + GM_GPSR_LINK_UP = 1<<12, /* Bit 12: Link Up Status */ + GM_GPSR_PAUSE = 1<<11, /* Bit 11: Pause State */ + GM_GPSR_TX_ACTIVE = 1<<10, /* Bit 10: Tx in Progress */ + GM_GPSR_EXC_COL = 1<<9, /* Bit 9: Excessive Collisions Occured */ + GM_GPSR_LAT_COL = 1<<8, /* Bit 8: Late Collisions Occured */ + + GM_GPSR_PHY_ST_CH = 1<<5, /* Bit 5: PHY Status Change */ + GM_GPSR_GIG_SPEED = 1<<4, /* Bit 4: Gigabit Speed (1 = 1000 Mbps) */ + GM_GPSR_PART_MODE = 1<<3, /* Bit 3: Partition mode */ + GM_GPSR_FC_RX_DIS = 1<<2, /* Bit 2: Rx Flow-Control Mode Disabled */ + GM_GPSR_PROM_EN = 1<<1, /* Bit 1: Promiscuous Mode Enabled */ +}; + +/* GM_GP_CTRL 16 bit r/w General Purpose Control Register */ +enum { + GM_GPCR_PROM_ENA = 1<<14, /* Bit 14: Enable Promiscuous Mode */ + GM_GPCR_FC_TX_DIS = 1<<13, /* Bit 13: Disable Tx Flow-Control Mode */ + GM_GPCR_TX_ENA = 1<<12, /* Bit 12: Enable Transmit */ + GM_GPCR_RX_ENA = 1<<11, /* Bit 11: Enable Receive */ + GM_GPCR_BURST_ENA = 1<<10, /* Bit 10: Enable Burst Mode */ + GM_GPCR_LOOP_ENA = 1<<9, /* Bit 9: Enable MAC Loopback Mode */ + GM_GPCR_PART_ENA = 1<<8, /* Bit 8: Enable Partition Mode */ + GM_GPCR_GIGS_ENA = 1<<7, /* Bit 7: Gigabit Speed (1000 Mbps) */ + GM_GPCR_FL_PASS = 1<<6, /* Bit 6: Force Link Pass */ + GM_GPCR_DUP_FULL = 1<<5, /* Bit 5: Full Duplex Mode */ + GM_GPCR_FC_RX_DIS = 1<<4, /* Bit 4: Disable Rx Flow-Control Mode */ + GM_GPCR_SPEED_100 = 1<<3, /* Bit 3: Port Speed 100 Mbps */ + GM_GPCR_AU_DUP_DIS = 1<<2, /* Bit 2: Disable Auto-Update Duplex */ + GM_GPCR_AU_FCT_DIS = 1<<1, /* Bit 1: Disable Auto-Update Flow-C. */ + GM_GPCR_AU_SPD_DIS = 1<<0, /* Bit 0: Disable Auto-Update Speed */ +}; + +#define GM_GPCR_SPEED_1000 (GM_GPCR_GIGS_ENA | GM_GPCR_SPEED_100) +#define GM_GPCR_AU_ALL_DIS (GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_FCT_DIS|GM_GPCR_AU_SPD_DIS) + +/* GM_TX_CTRL 16 bit r/w Transmit Control Register */ +enum { + GM_TXCR_FORCE_JAM = 1<<15, /* Bit 15: Force Jam / Flow-Control */ + GM_TXCR_CRC_DIS = 1<<14, /* Bit 14: Disable insertion of CRC */ + GM_TXCR_PAD_DIS = 1<<13, /* Bit 13: Disable padding of packets */ + GM_TXCR_COL_THR_MSK = 7<<10, /* Bit 12..10: Collision Threshold */ +}; + +#define TX_COL_THR(x) (((x)<<10) & GM_TXCR_COL_THR_MSK) +#define TX_COL_DEF 0x04 + +/* GM_RX_CTRL 16 bit r/w Receive Control Register */ +enum { + GM_RXCR_UCF_ENA = 1<<15, /* Bit 15: Enable Unicast filtering */ + GM_RXCR_MCF_ENA = 1<<14, /* Bit 14: Enable Multicast filtering */ + GM_RXCR_CRC_DIS = 1<<13, /* Bit 13: Remove 4-byte CRC */ + GM_RXCR_PASS_FC = 1<<12, /* Bit 12: Pass FC packets to FIFO */ +}; + +/* GM_TX_PARAM 16 bit r/w Transmit Parameter Register */ +enum { + GM_TXPA_JAMLEN_MSK = 0x03<<14, /* Bit 15..14: Jam Length */ + GM_TXPA_JAMIPG_MSK = 0x1f<<9, /* Bit 13..9: Jam IPG */ + GM_TXPA_JAMDAT_MSK = 0x1f<<4, /* Bit 8..4: IPG Jam to Data */ + GM_TXPA_BO_LIM_MSK = 0x0f, /* Bit 3.. 0: Backoff Limit Mask */ + + TX_JAM_LEN_DEF = 0x03, + TX_JAM_IPG_DEF = 0x0b, + TX_IPG_JAM_DEF = 0x1c, + TX_BOF_LIM_DEF = 0x04, +}; + +#define TX_JAM_LEN_VAL(x) (((x)<<14) & GM_TXPA_JAMLEN_MSK) +#define TX_JAM_IPG_VAL(x) (((x)<<9) & GM_TXPA_JAMIPG_MSK) +#define TX_IPG_JAM_DATA(x) (((x)<<4) & GM_TXPA_JAMDAT_MSK) +#define TX_BACK_OFF_LIM(x) ((x) & GM_TXPA_BO_LIM_MSK) + + +/* GM_SERIAL_MODE 16 bit r/w Serial Mode Register */ +enum { + GM_SMOD_DATABL_MSK = 0x1f<<11, /* Bit 15..11: Data Blinder (r/o) */ + GM_SMOD_LIMIT_4 = 1<<10, /* Bit 10: 4 consecutive Tx trials */ + GM_SMOD_VLAN_ENA = 1<<9, /* Bit 9: Enable VLAN (Max. Frame Len) */ + GM_SMOD_JUMBO_ENA = 1<<8, /* Bit 8: Enable Jumbo (Max. Frame Len) */ + GM_SMOD_IPG_MSK = 0x1f /* Bit 4..0: Inter-Packet Gap (IPG) */ +}; + +#define DATA_BLIND_VAL(x) (((x)<<11) & GM_SMOD_DATABL_MSK) +#define DATA_BLIND_DEF 0x04 + +#define IPG_DATA_VAL(x) (x & GM_SMOD_IPG_MSK) +#define IPG_DATA_DEF 0x1e + +/* GM_SMI_CTRL 16 bit r/w SMI Control Register */ +enum { + GM_SMI_CT_PHY_A_MSK = 0x1f<<11,/* Bit 15..11: PHY Device Address */ + GM_SMI_CT_REG_A_MSK = 0x1f<<6,/* Bit 10.. 6: PHY Register Address */ + GM_SMI_CT_OP_RD = 1<<5, /* Bit 5: OpCode Read (0=Write)*/ + GM_SMI_CT_RD_VAL = 1<<4, /* Bit 4: Read Valid (Read completed) */ + GM_SMI_CT_BUSY = 1<<3, /* Bit 3: Busy (Operation in progress) */ +}; + +#define GM_SMI_CT_PHY_AD(x) (((u16)(x)<<11) & GM_SMI_CT_PHY_A_MSK) +#define GM_SMI_CT_REG_AD(x) (((u16)(x)<<6) & GM_SMI_CT_REG_A_MSK) + +/* GM_PHY_ADDR 16 bit r/w GPHY Address Register */ +enum { + GM_PAR_MIB_CLR = 1<<5, /* Bit 5: Set MIB Clear Counter Mode */ + GM_PAR_MIB_TST = 1<<4, /* Bit 4: MIB Load Counter (Test Mode) */ +}; + +/* Receive Frame Status Encoding */ +enum { + GMR_FS_LEN = 0x7fff<<16, /* Bit 30..16: Rx Frame Length */ + GMR_FS_VLAN = 1<<13, /* VLAN Packet */ + GMR_FS_JABBER = 1<<12, /* Jabber Packet */ + GMR_FS_UN_SIZE = 1<<11, /* Undersize Packet */ + GMR_FS_MC = 1<<10, /* Multicast Packet */ + GMR_FS_BC = 1<<9, /* Broadcast Packet */ + GMR_FS_RX_OK = 1<<8, /* Receive OK (Good Packet) */ + GMR_FS_GOOD_FC = 1<<7, /* Good Flow-Control Packet */ + GMR_FS_BAD_FC = 1<<6, /* Bad Flow-Control Packet */ + GMR_FS_MII_ERR = 1<<5, /* MII Error */ + GMR_FS_LONG_ERR = 1<<4, /* Too Long Packet */ + GMR_FS_FRAGMENT = 1<<3, /* Fragment */ + + GMR_FS_CRC_ERR = 1<<1, /* CRC Error */ + GMR_FS_RX_FF_OV = 1<<0, /* Rx FIFO Overflow */ + + GMR_FS_ANY_ERR = GMR_FS_RX_FF_OV | GMR_FS_CRC_ERR | + GMR_FS_FRAGMENT | GMR_FS_LONG_ERR | + GMR_FS_MII_ERR | GMR_FS_BAD_FC | + GMR_FS_UN_SIZE | GMR_FS_JABBER, +}; + +/* RX_GMF_CTRL_T 32 bit Rx GMAC FIFO Control/Test */ +enum { + RX_TRUNC_ON = 1<<27, /* enable packet truncation */ + RX_TRUNC_OFF = 1<<26, /* disable packet truncation */ + RX_VLAN_STRIP_ON = 1<<25, /* enable VLAN stripping */ + RX_VLAN_STRIP_OFF = 1<<24, /* disable VLAN stripping */ + + RX_MACSEC_FLUSH_ON = 1<<23, + RX_MACSEC_FLUSH_OFF = 1<<22, + RX_MACSEC_ASF_FLUSH_ON = 1<<21, + RX_MACSEC_ASF_FLUSH_OFF = 1<<20, + + GMF_RX_OVER_ON = 1<<19, /* enable flushing on receive overrun */ + GMF_RX_OVER_OFF = 1<<18, /* disable flushing on receive overrun */ + GMF_ASF_RX_OVER_ON = 1<<17, /* enable flushing of ASF when overrun */ + GMF_ASF_RX_OVER_OFF = 1<<16, /* disable flushing of ASF when overrun */ + + GMF_WP_TST_ON = 1<<14, /* Write Pointer Test On */ + GMF_WP_TST_OFF = 1<<13, /* Write Pointer Test Off */ + GMF_WP_STEP = 1<<12, /* Write Pointer Step/Increment */ + + GMF_RP_TST_ON = 1<<10, /* Read Pointer Test On */ + GMF_RP_TST_OFF = 1<<9, /* Read Pointer Test Off */ + GMF_RP_STEP = 1<<8, /* Read Pointer Step/Increment */ + GMF_RX_F_FL_ON = 1<<7, /* Rx FIFO Flush Mode On */ + GMF_RX_F_FL_OFF = 1<<6, /* Rx FIFO Flush Mode Off */ + GMF_CLI_RX_FO = 1<<5, /* Clear IRQ Rx FIFO Overrun */ + GMF_CLI_RX_C = 1<<4, /* Clear IRQ Rx Frame Complete */ + + GMF_OPER_ON = 1<<3, /* Operational Mode On */ + GMF_OPER_OFF = 1<<2, /* Operational Mode Off */ + GMF_RST_CLR = 1<<1, /* Clear GMAC FIFO Reset */ + GMF_RST_SET = 1<<0, /* Set GMAC FIFO Reset */ + + RX_GMF_FL_THR_DEF = 0xa, /* flush threshold (default) */ + + GMF_RX_CTRL_DEF = GMF_OPER_ON | GMF_RX_F_FL_ON, +}; + +/* TX_GMF_EA 32 bit Tx GMAC FIFO End Address */ +enum { + TX_DYN_WM_ENA = 3, /* Yukon-FE+ specific */ +}; + +/* TX_GMF_CTRL_T 32 bit Tx GMAC FIFO Control/Test */ +enum { + TX_STFW_DIS = 1<<31,/* Disable Store & Forward (Yukon-EC Ultra) */ + TX_STFW_ENA = 1<<30,/* Enable Store & Forward (Yukon-EC Ultra) */ + + TX_VLAN_TAG_ON = 1<<25,/* enable VLAN tagging */ + TX_VLAN_TAG_OFF = 1<<24,/* disable VLAN tagging */ + + TX_JUMBO_ENA = 1<<23,/* PCI Jumbo Mode enable (Yukon-EC Ultra) */ + TX_JUMBO_DIS = 1<<22,/* PCI Jumbo Mode enable (Yukon-EC Ultra) */ + + GMF_WSP_TST_ON = 1<<18,/* Write Shadow Pointer Test On */ + GMF_WSP_TST_OFF = 1<<17,/* Write Shadow Pointer Test Off */ + GMF_WSP_STEP = 1<<16,/* Write Shadow Pointer Step/Increment */ + + GMF_CLI_TX_FU = 1<<6, /* Clear IRQ Tx FIFO Underrun */ + GMF_CLI_TX_FC = 1<<5, /* Clear IRQ Tx Frame Complete */ + GMF_CLI_TX_PE = 1<<4, /* Clear IRQ Tx Parity Error */ +}; + +/* GMAC_TI_ST_CTRL 8 bit Time Stamp Timer Ctrl Reg (YUKON only) */ +enum { + GMT_ST_START = 1<<2, /* Start Time Stamp Timer */ + GMT_ST_STOP = 1<<1, /* Stop Time Stamp Timer */ + GMT_ST_CLR_IRQ = 1<<0, /* Clear Time Stamp Timer IRQ */ +}; + +/* B28_Y2_ASF_STAT_CMD 32 bit ASF Status and Command Reg */ +enum { + Y2_ASF_OS_PRES = 1<<4, /* ASF operation system present */ + Y2_ASF_RESET = 1<<3, /* ASF system in reset state */ + Y2_ASF_RUNNING = 1<<2, /* ASF system operational */ + Y2_ASF_CLR_HSTI = 1<<1, /* Clear ASF IRQ */ + Y2_ASF_IRQ = 1<<0, /* Issue an IRQ to ASF system */ + + Y2_ASF_UC_STATE = 3<<2, /* ASF uC State */ + Y2_ASF_CLK_HALT = 0, /* ASF system clock stopped */ +}; + +/* B28_Y2_ASF_HOST_COM 32 bit ASF Host Communication Reg */ +enum { + Y2_ASF_CLR_ASFI = 1<<1, /* Clear host IRQ */ + Y2_ASF_HOST_IRQ = 1<<0, /* Issue an IRQ to HOST system */ +}; +/* HCU_CCSR CPU Control and Status Register */ +enum { + HCU_CCSR_SMBALERT_MONITOR= 1<<27, /* SMBALERT pin monitor */ + HCU_CCSR_CPU_SLEEP = 1<<26, /* CPU sleep status */ + /* Clock Stretching Timeout */ + HCU_CCSR_CS_TO = 1<<25, + HCU_CCSR_WDOG = 1<<24, /* Watchdog Reset */ + + HCU_CCSR_CLR_IRQ_HOST = 1<<17, /* Clear IRQ_HOST */ + HCU_CCSR_SET_IRQ_HCU = 1<<16, /* Set IRQ_HCU */ + + HCU_CCSR_AHB_RST = 1<<9, /* Reset AHB bridge */ + HCU_CCSR_CPU_RST_MODE = 1<<8, /* CPU Reset Mode */ + + HCU_CCSR_SET_SYNC_CPU = 1<<5, + HCU_CCSR_CPU_CLK_DIVIDE_MSK = 3<<3,/* CPU Clock Divide */ + HCU_CCSR_CPU_CLK_DIVIDE_BASE= 1<<3, + HCU_CCSR_OS_PRSNT = 1<<2, /* ASF OS Present */ +/* Microcontroller State */ + HCU_CCSR_UC_STATE_MSK = 3, + HCU_CCSR_UC_STATE_BASE = 1<<0, + HCU_CCSR_ASF_RESET = 0, + HCU_CCSR_ASF_HALTED = 1<<1, + HCU_CCSR_ASF_RUNNING = 1<<0, +}; + +/* HCU_HCSR Host Control and Status Register */ +enum { + HCU_HCSR_SET_IRQ_CPU = 1<<16, /* Set IRQ_CPU */ + + HCU_HCSR_CLR_IRQ_HCU = 1<<1, /* Clear IRQ_HCU */ + HCU_HCSR_SET_IRQ_HOST = 1<<0, /* Set IRQ_HOST */ +}; + +/* STAT_CTRL 32 bit Status BMU control register (Yukon-2 only) */ +enum { + SC_STAT_CLR_IRQ = 1<<4, /* Status Burst IRQ clear */ + SC_STAT_OP_ON = 1<<3, /* Operational Mode On */ + SC_STAT_OP_OFF = 1<<2, /* Operational Mode Off */ + SC_STAT_RST_CLR = 1<<1, /* Clear Status Unit Reset (Enable) */ + SC_STAT_RST_SET = 1<<0, /* Set Status Unit Reset */ +}; + +/* GMAC_CTRL 32 bit GMAC Control Reg (YUKON only) */ +enum { + GMC_SET_RST = 1<<15,/* MAC SEC RST */ + GMC_SEC_RST_OFF = 1<<14,/* MAC SEC RSt OFF */ + GMC_BYP_MACSECRX_ON = 1<<13,/* Bypass macsec RX */ + GMC_BYP_MACSECRX_OFF= 1<<12,/* Bypass macsec RX off */ + GMC_BYP_MACSECTX_ON = 1<<11,/* Bypass macsec TX */ + GMC_BYP_MACSECTX_OFF= 1<<10,/* Bypass macsec TX off*/ + GMC_BYP_RETR_ON = 1<<9, /* Bypass retransmit FIFO On */ + GMC_BYP_RETR_OFF= 1<<8, /* Bypass retransmit FIFO Off */ + + GMC_H_BURST_ON = 1<<7, /* Half Duplex Burst Mode On */ + GMC_H_BURST_OFF = 1<<6, /* Half Duplex Burst Mode Off */ + GMC_F_LOOPB_ON = 1<<5, /* FIFO Loopback On */ + GMC_F_LOOPB_OFF = 1<<4, /* FIFO Loopback Off */ + GMC_PAUSE_ON = 1<<3, /* Pause On */ + GMC_PAUSE_OFF = 1<<2, /* Pause Off */ + GMC_RST_CLR = 1<<1, /* Clear GMAC Reset */ + GMC_RST_SET = 1<<0, /* Set GMAC Reset */ +}; + +/* GPHY_CTRL 32 bit GPHY Control Reg (YUKON only) */ +enum { + GPC_TX_PAUSE = 1<<30, /* Tx pause enabled (ro) */ + GPC_RX_PAUSE = 1<<29, /* Rx pause enabled (ro) */ + GPC_SPEED = 3<<27, /* PHY speed (ro) */ + GPC_LINK = 1<<26, /* Link up (ro) */ + GPC_DUPLEX = 1<<25, /* Duplex (ro) */ + GPC_CLOCK = 1<<24, /* 125Mhz clock stable (ro) */ + + GPC_PDOWN = 1<<23, /* Internal regulator 2.5 power down */ + GPC_TSTMODE = 1<<22, /* Test mode */ + GPC_REG18 = 1<<21, /* Reg18 Power down */ + GPC_REG12SEL = 3<<19, /* Reg12 power setting */ + GPC_REG18SEL = 3<<17, /* Reg18 power setting */ + GPC_SPILOCK = 1<<16, /* SPI lock (ASF) */ + + GPC_LEDMUX = 3<<14, /* LED Mux */ + GPC_INTPOL = 1<<13, /* Interrupt polarity */ + GPC_DETECT = 1<<12, /* Energy detect */ + GPC_1000HD = 1<<11, /* Enable 1000Mbit HD */ + GPC_SLAVE = 1<<10, /* Slave mode */ + GPC_PAUSE = 1<<9, /* Pause enable */ + GPC_LEDCTL = 3<<6, /* GPHY Leds */ + + GPC_RST_CLR = 1<<1, /* Clear GPHY Reset */ + GPC_RST_SET = 1<<0, /* Set GPHY Reset */ +}; + +/* GMAC_IRQ_SRC 8 bit GMAC Interrupt Source Reg (YUKON only) */ +/* GMAC_IRQ_MSK 8 bit GMAC Interrupt Mask Reg (YUKON only) */ +enum { + GM_IS_TX_CO_OV = 1<<5, /* Transmit Counter Overflow IRQ */ + GM_IS_RX_CO_OV = 1<<4, /* Receive Counter Overflow IRQ */ + GM_IS_TX_FF_UR = 1<<3, /* Transmit FIFO Underrun */ + GM_IS_TX_COMPL = 1<<2, /* Frame Transmission Complete */ + GM_IS_RX_FF_OR = 1<<1, /* Receive FIFO Overrun */ + GM_IS_RX_COMPL = 1<<0, /* Frame Reception Complete */ + +#define GMAC_DEF_MSK GM_IS_TX_FF_UR +}; + +/* GMAC_LINK_CTRL 16 bit GMAC Link Control Reg (YUKON only) */ +enum { /* Bits 15.. 2: reserved */ + GMLC_RST_CLR = 1<<1, /* Clear GMAC Link Reset */ + GMLC_RST_SET = 1<<0, /* Set GMAC Link Reset */ +}; + + +/* WOL_CTRL_STAT 16 bit WOL Control/Status Reg */ +enum { + WOL_CTL_LINK_CHG_OCC = 1<<15, + WOL_CTL_MAGIC_PKT_OCC = 1<<14, + WOL_CTL_PATTERN_OCC = 1<<13, + WOL_CTL_CLEAR_RESULT = 1<<12, + WOL_CTL_ENA_PME_ON_LINK_CHG = 1<<11, + WOL_CTL_DIS_PME_ON_LINK_CHG = 1<<10, + WOL_CTL_ENA_PME_ON_MAGIC_PKT = 1<<9, + WOL_CTL_DIS_PME_ON_MAGIC_PKT = 1<<8, + WOL_CTL_ENA_PME_ON_PATTERN = 1<<7, + WOL_CTL_DIS_PME_ON_PATTERN = 1<<6, + WOL_CTL_ENA_LINK_CHG_UNIT = 1<<5, + WOL_CTL_DIS_LINK_CHG_UNIT = 1<<4, + WOL_CTL_ENA_MAGIC_PKT_UNIT = 1<<3, + WOL_CTL_DIS_MAGIC_PKT_UNIT = 1<<2, + WOL_CTL_ENA_PATTERN_UNIT = 1<<1, + WOL_CTL_DIS_PATTERN_UNIT = 1<<0, +}; + + +/* Control flags */ +enum { + UDPTCP = 1<<0, + CALSUM = 1<<1, + WR_SUM = 1<<2, + INIT_SUM= 1<<3, + LOCK_SUM= 1<<4, + INS_VLAN= 1<<5, + EOP = 1<<7, +}; + +enum { + HW_OWNER = 1<<7, + OP_TCPWRITE = 0x11, + OP_TCPSTART = 0x12, + OP_TCPINIT = 0x14, + OP_TCPLCK = 0x18, + OP_TCPCHKSUM = OP_TCPSTART, + OP_TCPIS = OP_TCPINIT | OP_TCPSTART, + OP_TCPLW = OP_TCPLCK | OP_TCPWRITE, + OP_TCPLSW = OP_TCPLCK | OP_TCPSTART | OP_TCPWRITE, + OP_TCPLISW = OP_TCPLCK | OP_TCPINIT | OP_TCPSTART | OP_TCPWRITE, + + OP_ADDR64 = 0x21, + OP_VLAN = 0x22, + OP_ADDR64VLAN = OP_ADDR64 | OP_VLAN, + OP_LRGLEN = 0x24, + OP_LRGLENVLAN = OP_LRGLEN | OP_VLAN, + OP_MSS = 0x28, + OP_MSSVLAN = OP_MSS | OP_VLAN, + + OP_BUFFER = 0x40, + OP_PACKET = 0x41, + OP_LARGESEND = 0x43, + OP_LSOV2 = 0x45, + +/* YUKON-2 STATUS opcodes defines */ + OP_RXSTAT = 0x60, + OP_RXTIMESTAMP = 0x61, + OP_RXVLAN = 0x62, + OP_RXCHKS = 0x64, + OP_RXCHKSVLAN = OP_RXCHKS | OP_RXVLAN, + OP_RXTIMEVLAN = OP_RXTIMESTAMP | OP_RXVLAN, + OP_RSS_HASH = 0x65, + OP_TXINDEXLE = 0x68, + OP_MACSEC = 0x6c, + OP_PUTIDX = 0x70, +}; + +enum status_css { + CSS_TCPUDPCSOK = 1<<7, /* TCP / UDP checksum is ok */ + CSS_ISUDP = 1<<6, /* packet is a UDP packet */ + CSS_ISTCP = 1<<5, /* packet is a TCP packet */ + CSS_ISIPFRAG = 1<<4, /* packet is a TCP/UDP frag, CS calc not done */ + CSS_ISIPV6 = 1<<3, /* packet is a IPv6 packet */ + CSS_IPV4CSUMOK = 1<<2, /* IP v4: TCP header checksum is ok */ + CSS_ISIPV4 = 1<<1, /* packet is a IPv4 packet */ + CSS_LINK_BIT = 1<<0, /* port number (legacy) */ +}; + +/* Yukon 2 hardware interface */ +struct sky2_tx_le { + u32 addr; + u16 length; /* also vlan tag or checksum start */ + u8 ctrl; + u8 opcode; +} __attribute((packed)); + +struct sky2_rx_le { + u32 addr; + u16 length; + u8 ctrl; + u8 opcode; +} __attribute((packed)); + +struct sky2_status_le { + u32 status; /* also checksum */ + u16 length; /* also vlan tag */ + u8 css; + u8 opcode; +} __attribute((packed)); + +struct tx_ring_info { + struct io_buffer *iob; + u32 mapaddr; + u32 maplen; +}; + +struct rx_ring_info { + struct io_buffer *iob; + u32 data_addr; + u32 data_size; +}; + +enum flow_control { + FC_NONE = 0, + FC_TX = 1, + FC_RX = 2, + FC_BOTH = 3, +}; + +struct sky2_port { + struct sky2_hw *hw; + struct net_device *netdev; + unsigned port; + + struct tx_ring_info *tx_ring; + struct sky2_tx_le *tx_le; + u16 tx_cons; /* next le to check */ + u16 tx_prod; /* next le to use */ + + struct rx_ring_info *rx_ring; + struct sky2_rx_le *rx_le; + + u16 rx_next; /* next re to check */ + u16 rx_put; /* next le index to use */ + u16 rx_data_size; + + u32 rx_le_map; + u32 tx_le_map; + u16 advertising; /* ADVERTISED_ bits */ + u16 speed; /* SPEED_1000, SPEED_100, ... */ + u8 autoneg; /* AUTONEG_ENABLE, AUTONEG_DISABLE */ + u8 duplex; /* DUPLEX_HALF, DUPLEX_FULL */ + enum flow_control flow_mode; + enum flow_control flow_status; +}; + +struct sky2_hw { + unsigned long regs; + struct pci_device *pdev; + struct net_device *dev[2]; + unsigned long flags; +#define SKY2_HW_USE_MSI 0x00000001 +#define SKY2_HW_FIBRE_PHY 0x00000002 +#define SKY2_HW_GIGABIT 0x00000004 +#define SKY2_HW_NEWER_PHY 0x00000008 +#define SKY2_HW_RAM_BUFFER 0x00000010 +#define SKY2_HW_NEW_LE 0x00000020 /* new LSOv2 format */ +#define SKY2_HW_AUTO_TX_SUM 0x00000040 /* new IP decode for Tx */ +#define SKY2_HW_ADV_POWER_CTL 0x00000080 /* additional PHY power regs */ + + u8 chip_id; + u8 chip_rev; + u8 pmd_type; + u8 ports; + + struct sky2_status_le *st_le; + u32 st_idx; + u32 st_dma; +}; + +static inline int sky2_is_copper(const struct sky2_hw *hw) +{ + return !(hw->flags & SKY2_HW_FIBRE_PHY); +} + +/* Register accessor for memory mapped device */ +static inline u32 sky2_read32(const struct sky2_hw *hw, unsigned reg) +{ + return readl(hw->regs + reg); +} + +static inline u16 sky2_read16(const struct sky2_hw *hw, unsigned reg) +{ + return readw(hw->regs + reg); +} + +static inline u8 sky2_read8(const struct sky2_hw *hw, unsigned reg) +{ + return readb(hw->regs + reg); +} + +static inline void sky2_write32(const struct sky2_hw *hw, unsigned reg, u32 val) +{ + writel(val, hw->regs + reg); +} + +static inline void sky2_write16(const struct sky2_hw *hw, unsigned reg, u16 val) +{ + writew(val, hw->regs + reg); +} + +static inline void sky2_write8(const struct sky2_hw *hw, unsigned reg, u8 val) +{ + writeb(val, hw->regs + reg); +} + +/* Yukon PHY related registers */ +#define SK_GMAC_REG(port,reg) \ + (BASE_GMAC_1 + (port) * (BASE_GMAC_2-BASE_GMAC_1) + (reg)) +#define GM_PHY_RETRIES 100 + +static inline u16 gma_read16(const struct sky2_hw *hw, unsigned port, unsigned reg) +{ + return sky2_read16(hw, SK_GMAC_REG(port,reg)); +} + +static inline u32 gma_read32(struct sky2_hw *hw, unsigned port, unsigned reg) +{ + unsigned base = SK_GMAC_REG(port, reg); + return (u32) sky2_read16(hw, base) + | (u32) sky2_read16(hw, base+4) << 16; +} + +static inline void gma_write16(const struct sky2_hw *hw, unsigned port, int r, u16 v) +{ + sky2_write16(hw, SK_GMAC_REG(port,r), v); +} + +static inline void gma_set_addr(struct sky2_hw *hw, unsigned port, unsigned reg, + const u8 *addr) +{ + gma_write16(hw, port, reg, (u16) addr[0] | ((u16) addr[1] << 8)); + gma_write16(hw, port, reg+4,(u16) addr[2] | ((u16) addr[3] << 8)); + gma_write16(hw, port, reg+8,(u16) addr[4] | ((u16) addr[5] << 8)); +} + +/* PCI config space access */ +static inline u32 sky2_pci_read32(const struct sky2_hw *hw, unsigned reg) +{ + return sky2_read32(hw, Y2_CFG_SPC + reg); +} + +static inline u16 sky2_pci_read16(const struct sky2_hw *hw, unsigned reg) +{ + return sky2_read16(hw, Y2_CFG_SPC + reg); +} + +static inline void sky2_pci_write32(struct sky2_hw *hw, unsigned reg, u32 val) +{ + sky2_write32(hw, Y2_CFG_SPC + reg, val); +} + +static inline void sky2_pci_write16(struct sky2_hw *hw, unsigned reg, u16 val) +{ + sky2_write16(hw, Y2_CFG_SPC + reg, val); +} +#endif diff --git a/src/include/gpxe/errfile.h b/src/include/gpxe/errfile.h index 8fb6a95f..b7f63fc5 100644 --- a/src/include/gpxe/errfile.h +++ b/src/include/gpxe/errfile.h @@ -111,6 +111,7 @@ FILE_LICENCE ( GPL2_OR_LATER ); #define ERRFILE_ne2k_isa ( ERRFILE_DRIVER | 0x004c0000 ) #define ERRFILE_b44 ( ERRFILE_DRIVER | 0x004d0000 ) #define ERRFILE_rtl818x ( ERRFILE_DRIVER | 0x004e0000 ) +#define ERRFILE_sky2 ( ERRFILE_DRIVER | 0x004f0000 ) #define ERRFILE_scsi ( ERRFILE_DRIVER | 0x00700000 ) #define ERRFILE_arbel ( ERRFILE_DRIVER | 0x00710000 ) -- cgit v1.2.3-55-g7522