blob: bbdfa9c2d469fdb5a2945350d6d25486b54ffee6 (
plain) (
tree)
|
|
/*
* include/linux/serial.h
*
* Copyright (C) 1992, 1994 by Theodore Ts'o.
*
* Redistribution of this file is permitted under the terms of the GNU
* Public License (GPL)
*
* These are the UART port assignments, expressed as offsets from the base
* register. These assignments should hold for any serial port based on
* a 8250, 16450, or 16550(A).
*/
#ifndef _LINUX_SERIAL_REG_H
#define _LINUX_SERIAL_REG_H
#define UART_RX 0 /* In: Receive buffer (DLAB=0) */
#define UART_TX 0 /* Out: Transmit buffer (DLAB=0) */
#define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */
#define UART_DLM 1 /* Out: Divisor Latch High (DLAB=1) */
#define UART_IER 1 /* Out: Interrupt Enable Register */
#define UART_IIR 2 /* In: Interrupt ID Register */
#define UART_FCR 2 /* Out: FIFO Control Register */
#define UART_EFR 2 /* I/O: Extended Features Register */
/* (DLAB=1, 16C660 only) */
#define UART_LCR 3 /* Out: Line Control Register */
#define UART_MCR 4 /* Out: Modem Control Register */
#define UART_LSR 5 /* In: Line Status Register */
#define UART_MSR 6 /* In: Modem Status Register */
#define UART_SCR 7 /* I/O: Scratch Register */
/*
* These are the definitions for the FIFO Control Register
* (16650 only)
*/
#define UART_FCR_ENABLE_FIFO 0x01 /* Enable the FIFO */
#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */
#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */
#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */
#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */
#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */
#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */
#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */
#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */
/* 16650 redefinitions */
#define UART_FCR6_R_TRIGGER_8 0x00 /* Mask for receive trigger set at 1 */
#define UART_FCR6_R_TRIGGER_16 0x40 /* Mask for receive trigger set at 4 */
#define UART_FCR6_R_TRIGGER_24 0x80 /* Mask for receive trigger set at 8 */
#define UART_FCR6_R_TRIGGER_28 0xC0 /* Mask for receive trigger set at 14 */
#define UART_FCR6_T_TRIGGER_16 0x00 /* Mask for transmit trigger set at 16 */
#define UART_FCR6_T_TRIGGER_8 0x10 /* Mask for transmit trigger set at 8 */
#define UART_FCR6_T_TRIGGER_24 0x20 /* Mask for transmit trigger set at 24 */
#define UART_FCR6_T_TRIGGER_30 0x30 /* Mask for transmit trigger set at 30 */
/*
* These are the definitions for the Line Control Register
*
* Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
* UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
*/
#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */
#define UART_LCR_SBC 0x40 /* Set break control */
#define UART_LCR_SPAR 0x20 /* Stick parity (?) */
#define UART_LCR_EPAR 0x10 /* Even parity select */
#define UART_LCR_PARITY 0x08 /* Parity Enable */
#define UART_LCR_STOP 0x04 /* Stop bits: 0=1 stop bit, 1= 2 stop bits */
#define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */
#define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */
#define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */
#define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */
/*
* These are the definitions for the Line Status Register
*/
#define UART_LSR_TEMT 0x40 /* Transmitter empty */
#define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */
#define UART_LSR_BI 0x10 /* Break interrupt indicator */
#define UART_LSR_FE 0x08 /* Frame error indicator */
#define UART_LSR_PE 0x04 /* Parity error indicator */
#define UART_LSR_OE 0x02 /* Overrun error indicator */
#define UART_LSR_DR 0x01 /* Receiver data ready */
/*
* These are the definitions for the Interrupt Identification Register
*/
#define UART_IIR_NO_INT 0x01 /* No interrupts pending */
#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */
#define UART_IIR_MSI 0x00 /* Modem status interrupt */
#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */
#define UART_IIR_RDI 0x04 /* Receiver data interrupt */
#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */
/*
* These are the definitions for the Interrupt Enable Register
*/
#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */
#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */
#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */
#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */
/*
* These are the definitions for the Modem Control Register
*/
#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */
#define UART_MCR_OUT2 0x08 /* Out2 complement */
#define UART_MCR_OUT1 0x04 /* Out1 complement */
#define UART_MCR_RTS 0x02 /* RTS complement */
#define UART_MCR_DTR 0x01 /* DTR complement */
/*
* These are the definitions for the Modem Status Register
*/
#define UART_MSR_DCD 0x80 /* Data Carrier Detect */
#define UART_MSR_RI 0x40 /* Ring Indicator */
#define UART_MSR_DSR 0x20 /* Data Set Ready */
#define UART_MSR_CTS 0x10 /* Clear to Send */
#define UART_MSR_DDCD 0x08 /* Delta DCD */
#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */
#define UART_MSR_DDSR 0x02 /* Delta DSR */
#define UART_MSR_DCTS 0x01 /* Delta CTS */
#define UART_MSR_ANY_DELTA 0x0F /* Any of the delta bits! */
/*
* These are the definitions for the Extended Features Register
* (StarTech 16C660 only, when DLAB=1)
*/
#define UART_EFR_CTS 0x80 /* CTS flow control */
#define UART_EFR_RTS 0x40 /* RTS flow control */
#define UART_EFR_SCD 0x20 /* Special character detect */
#define UART_EFR_ENI 0x10 /* Enhanced Interrupt */
/*
* the low four bits control software flow control
*/
#define serial_echo_outb(v,a) outb((v),(a)+serial_base_ports[serial_tty])
#define serial_echo_inb(a) inb((a)+serial_base_ports[serial_tty])
#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
/* Wait for transmitter & holding register to empty */
#define WAIT_FOR_XMITR \
do { \
lsr = serial_echo_inb(UART_LSR); \
} while ((lsr & BOTH_EMPTY) != BOTH_EMPTY)
#if 0
static inline void serial_echo(int ch)
{
int lsr;
WAIT_FOR_XMITR;
serial_echo_outb(ch, UART_TX);
}
static inline void serial_debug(int ch)
{
serial_echo(ch);
serial_echo('\r');
serial_echo('\n');
}
#endif
#endif /* _LINUX_SERIAL_REG_H */
|
