diff options
| -rw-r--r-- | drivers/soc/qcom/Kconfig | 9 | ||||
| -rw-r--r-- | drivers/soc/qcom/Makefile | 1 | ||||
| -rw-r--r-- | drivers/soc/qcom/qcom-geni-se.c | 748 | ||||
| -rw-r--r-- | include/linux/qcom-geni-se.h | 425 |
4 files changed, 1183 insertions, 0 deletions
diff --git a/drivers/soc/qcom/Kconfig b/drivers/soc/qcom/Kconfig index 5c4535b545cc..d0372de29834 100644 --- a/drivers/soc/qcom/Kconfig +++ b/drivers/soc/qcom/Kconfig @@ -3,6 +3,15 @@ # menu "Qualcomm SoC drivers" +config QCOM_GENI_SE + tristate "QCOM GENI Serial Engine Driver" + depends on ARCH_QCOM || COMPILE_TEST + help + This driver is used to manage Generic Interface (GENI) firmware based + Qualcomm Technologies, Inc. Universal Peripheral (QUP) Wrapper. This + driver is also used to manage the common aspects of multiple Serial + Engines present in the QUP. + config QCOM_GLINK_SSR tristate "Qualcomm Glink SSR driver" depends on RPMSG diff --git a/drivers/soc/qcom/Makefile b/drivers/soc/qcom/Makefile index dcebf2814e6d..959aa748f5ac 100644 --- a/drivers/soc/qcom/Makefile +++ b/drivers/soc/qcom/Makefile @@ -1,4 +1,5 @@ # SPDX-License-Identifier: GPL-2.0 +obj-$(CONFIG_QCOM_GENI_SE) += qcom-geni-se.o obj-$(CONFIG_QCOM_GLINK_SSR) += glink_ssr.o obj-$(CONFIG_QCOM_GSBI) += qcom_gsbi.o obj-$(CONFIG_QCOM_MDT_LOADER) += mdt_loader.o diff --git a/drivers/soc/qcom/qcom-geni-se.c b/drivers/soc/qcom/qcom-geni-se.c new file mode 100644 index 000000000000..feed3db21c10 --- /dev/null +++ b/drivers/soc/qcom/qcom-geni-se.c @@ -0,0 +1,748 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (c) 2017-2018, The Linux Foundation. All rights reserved. + +#include <linux/clk.h> +#include <linux/slab.h> +#include <linux/dma-mapping.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_platform.h> +#include <linux/pinctrl/consumer.h> +#include <linux/platform_device.h> +#include <linux/qcom-geni-se.h> + +/** + * DOC: Overview + * + * Generic Interface (GENI) Serial Engine (SE) Wrapper driver is introduced + * to manage GENI firmware based Qualcomm Universal Peripheral (QUP) Wrapper + * controller. QUP Wrapper is designed to support various serial bus protocols + * like UART, SPI, I2C, I3C, etc. + */ + +/** + * DOC: Hardware description + * + * GENI based QUP is a highly-flexible and programmable module for supporting + * a wide range of serial interfaces like UART, SPI, I2C, I3C, etc. A single + * QUP module can provide upto 8 serial interfaces, using its internal + * serial engines. The actual configuration is determined by the target + * platform configuration. The protocol supported by each interface is + * determined by the firmware loaded to the serial engine. Each SE consists + * of a DMA Engine and GENI sub modules which enable serial engines to + * support FIFO and DMA modes of operation. + * + * + * +-----------------------------------------+ + * |QUP Wrapper | + * | +----------------------------+ | + * --QUP & SE Clocks--> | Serial Engine N | +-IO------> + * | | ... | | Interface + * <---Clock Perf.----+ +----+-----------------------+ | | + * State Interface | | Serial Engine 1 | | | + * | | | | | + * | | | | | + * <--------AHB-------> | | | | + * | | +----+ | + * | | | | + * | | | | + * <------SE IRQ------+ +----------------------------+ | + * | | + * +-----------------------------------------+ + * + * Figure 1: GENI based QUP Wrapper + * + * The GENI submodules include primary and secondary sequencers which are + * used to drive TX & RX operations. On serial interfaces that operate using + * master-slave model, primary sequencer drives both TX & RX operations. On + * serial interfaces that operate using peer-to-peer model, primary sequencer + * drives TX operation and secondary sequencer drives RX operation. + */ + +/** + * DOC: Software description + * + * GENI SE Wrapper driver is structured into 2 parts: + * + * geni_wrapper represents QUP Wrapper controller. This part of the driver + * manages QUP Wrapper information such as hardware version, clock + * performance table that is common to all the internal serial engines. + * + * geni_se represents serial engine. This part of the driver manages serial + * engine information such as clocks, containing QUP Wrapper, etc. This part + * of driver also supports operations (eg. initialize the concerned serial + * engine, select between FIFO and DMA mode of operation etc.) that are + * common to all the serial engines and are independent of serial interfaces. + */ + +#define MAX_CLK_PERF_LEVEL 32 +#define NUM_AHB_CLKS 2 + +/** + * @struct geni_wrapper - Data structure to represent the QUP Wrapper Core + * @dev: Device pointer of the QUP wrapper core + * @base: Base address of this instance of QUP wrapper core + * @ahb_clks: Handle to the primary & secondary AHB clocks + */ +struct geni_wrapper { + struct device *dev; + void __iomem *base; + struct clk_bulk_data ahb_clks[NUM_AHB_CLKS]; +}; + +#define QUP_HW_VER_REG 0x4 + +/* Common SE registers */ +#define GENI_INIT_CFG_REVISION 0x0 +#define GENI_S_INIT_CFG_REVISION 0x4 +#define GENI_OUTPUT_CTRL 0x24 +#define GENI_CGC_CTRL 0x28 +#define GENI_CLK_CTRL_RO 0x60 +#define GENI_IF_DISABLE_RO 0x64 +#define GENI_FW_S_REVISION_RO 0x6c +#define SE_GENI_BYTE_GRAN 0x254 +#define SE_GENI_TX_PACKING_CFG0 0x260 +#define SE_GENI_TX_PACKING_CFG1 0x264 +#define SE_GENI_RX_PACKING_CFG0 0x284 +#define SE_GENI_RX_PACKING_CFG1 0x288 +#define SE_GENI_M_GP_LENGTH 0x910 +#define SE_GENI_S_GP_LENGTH 0x914 +#define SE_DMA_TX_PTR_L 0xc30 +#define SE_DMA_TX_PTR_H 0xc34 +#define SE_DMA_TX_ATTR 0xc38 +#define SE_DMA_TX_LEN 0xc3c +#define SE_DMA_TX_IRQ_EN 0xc48 +#define SE_DMA_TX_IRQ_EN_SET 0xc4c +#define SE_DMA_TX_IRQ_EN_CLR 0xc50 +#define SE_DMA_TX_LEN_IN 0xc54 +#define SE_DMA_TX_MAX_BURST 0xc5c +#define SE_DMA_RX_PTR_L 0xd30 +#define SE_DMA_RX_PTR_H 0xd34 +#define SE_DMA_RX_ATTR 0xd38 +#define SE_DMA_RX_LEN 0xd3c +#define SE_DMA_RX_IRQ_EN 0xd48 +#define SE_DMA_RX_IRQ_EN_SET 0xd4c +#define SE_DMA_RX_IRQ_EN_CLR 0xd50 +#define SE_DMA_RX_LEN_IN 0xd54 +#define SE_DMA_RX_MAX_BURST 0xd5c +#define SE_DMA_RX_FLUSH 0xd60 +#define SE_GSI_EVENT_EN 0xe18 +#define SE_IRQ_EN 0xe1c +#define SE_DMA_GENERAL_CFG 0xe30 + +/* GENI_OUTPUT_CTRL fields */ +#define DEFAULT_IO_OUTPUT_CTRL_MSK GENMASK(6, 0) + +/* GENI_CGC_CTRL fields */ +#define CFG_AHB_CLK_CGC_ON BIT(0) +#define CFG_AHB_WR_ACLK_CGC_ON BIT(1) +#define DATA_AHB_CLK_CGC_ON BIT(2) +#define SCLK_CGC_ON BIT(3) +#define TX_CLK_CGC_ON BIT(4) +#define RX_CLK_CGC_ON BIT(5) +#define EXT_CLK_CGC_ON BIT(6) +#define PROG_RAM_HCLK_OFF BIT(8) +#define PROG_RAM_SCLK_OFF BIT(9) +#define DEFAULT_CGC_EN GENMASK(6, 0) + +/* SE_GSI_EVENT_EN fields */ +#define DMA_RX_EVENT_EN BIT(0) +#define DMA_TX_EVENT_EN BIT(1) +#define GENI_M_EVENT_EN BIT(2) +#define GENI_S_EVENT_EN BIT(3) + +/* SE_IRQ_EN fields */ +#define DMA_RX_IRQ_EN BIT(0) +#define DMA_TX_IRQ_EN BIT(1) +#define GENI_M_IRQ_EN BIT(2) +#define GENI_S_IRQ_EN BIT(3) + +/* SE_DMA_GENERAL_CFG */ +#define DMA_RX_CLK_CGC_ON BIT(0) +#define DMA_TX_CLK_CGC_ON BIT(1) +#define DMA_AHB_SLV_CFG_ON BIT(2) +#define AHB_SEC_SLV_CLK_CGC_ON BIT(3) +#define DUMMY_RX_NON_BUFFERABLE BIT(4) +#define RX_DMA_ZERO_PADDING_EN BIT(5) +#define RX_DMA_IRQ_DELAY_MSK GENMASK(8, 6) +#define RX_DMA_IRQ_DELAY_SHFT 6 + +/** + * geni_se_get_qup_hw_version() - Read the QUP wrapper Hardware version + * @se: Pointer to the corresponding serial engine. + * + * Return: Hardware Version of the wrapper. + */ +u32 geni_se_get_qup_hw_version(struct geni_se *se) +{ + struct geni_wrapper *wrapper = se->wrapper; + + return readl_relaxed(wrapper->base + QUP_HW_VER_REG); +} +EXPORT_SYMBOL(geni_se_get_qup_hw_version); + +static void geni_se_io_set_mode(void __iomem *base) +{ + u32 val; + + val = readl_relaxed(base + SE_IRQ_EN); + val |= GENI_M_IRQ_EN | GENI_S_IRQ_EN; + val |= DMA_TX_IRQ_EN | DMA_RX_IRQ_EN; + writel_relaxed(val, base + SE_IRQ_EN); + + val = readl_relaxed(base + SE_GENI_DMA_MODE_EN); + val &= ~GENI_DMA_MODE_EN; + writel_relaxed(val, base + SE_GENI_DMA_MODE_EN); + + writel_relaxed(0, base + SE_GSI_EVENT_EN); +} + +static void geni_se_io_init(void __iomem *base) +{ + u32 val; + + val = readl_relaxed(base + GENI_CGC_CTRL); + val |= DEFAULT_CGC_EN; + writel_relaxed(val, base + GENI_CGC_CTRL); + + val = readl_relaxed(base + SE_DMA_GENERAL_CFG); + val |= AHB_SEC_SLV_CLK_CGC_ON | DMA_AHB_SLV_CFG_ON; + val |= DMA_TX_CLK_CGC_ON | DMA_RX_CLK_CGC_ON; + writel_relaxed(val, base + SE_DMA_GENERAL_CFG); + + writel_relaxed(DEFAULT_IO_OUTPUT_CTRL_MSK, base + GENI_OUTPUT_CTRL); + writel_relaxed(FORCE_DEFAULT, base + GENI_FORCE_DEFAULT_REG); +} + +/** + * geni_se_init() - Initialize the GENI serial engine + * @se: Pointer to the concerned serial engine. + * @rx_wm: Receive watermark, in units of FIFO words. + * @rx_rfr_wm: Ready-for-receive watermark, in units of FIFO words. + * + * This function is used to initialize the GENI serial engine, configure + * receive watermark and ready-for-receive watermarks. + */ +void geni_se_init(struct geni_se *se, u32 rx_wm, u32 rx_rfr) +{ + u32 val; + + geni_se_io_init(se->base); + geni_se_io_set_mode(se->base); + + writel_relaxed(rx_wm, se->base + SE_GENI_RX_WATERMARK_REG); + writel_relaxed(rx_rfr, se->base + SE_GENI_RX_RFR_WATERMARK_REG); + + val = readl_relaxed(se->base + SE_GENI_M_IRQ_EN); + val |= M_COMMON_GENI_M_IRQ_EN; + writel_relaxed(val, se->base + SE_GENI_M_IRQ_EN); + + val = readl_relaxed(se->base + SE_GENI_S_IRQ_EN); + val |= S_COMMON_GENI_S_IRQ_EN; + writel_relaxed(val, se->base + SE_GENI_S_IRQ_EN); +} +EXPORT_SYMBOL(geni_se_init); + +static void geni_se_select_fifo_mode(struct geni_se *se) +{ + u32 proto = geni_se_read_proto(se); + u32 val; + + writel_relaxed(0, se->base + SE_GSI_EVENT_EN); + writel_relaxed(0xffffffff, se->base + SE_GENI_M_IRQ_CLEAR); + writel_relaxed(0xffffffff, se->base + SE_GENI_S_IRQ_CLEAR); + writel_relaxed(0xffffffff, se->base + SE_DMA_TX_IRQ_CLR); + writel_relaxed(0xffffffff, se->base + SE_DMA_RX_IRQ_CLR); + writel_relaxed(0xffffffff, se->base + SE_IRQ_EN); + + val = readl_relaxed(se->base + SE_GENI_M_IRQ_EN); + if (proto != GENI_SE_UART) { + val |= M_CMD_DONE_EN | M_TX_FIFO_WATERMARK_EN; + val |= M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN; + } + writel_relaxed(val, se->base + SE_GENI_M_IRQ_EN); + + val = readl_relaxed(se->base + SE_GENI_S_IRQ_EN); + if (proto != GENI_SE_UART) + val |= S_CMD_DONE_EN; + writel_relaxed(val, se->base + SE_GENI_S_IRQ_EN); + + val = readl_relaxed(se->base + SE_GENI_DMA_MODE_EN); + val &= ~GENI_DMA_MODE_EN; + writel_relaxed(val, se->base + SE_GENI_DMA_MODE_EN); +} + +static void geni_se_select_dma_mode(struct geni_se *se) +{ + u32 val; + + writel_relaxed(0, se->base + SE_GSI_EVENT_EN); + writel_relaxed(0xffffffff, se->base + SE_GENI_M_IRQ_CLEAR); + writel_relaxed(0xffffffff, se->base + SE_GENI_S_IRQ_CLEAR); + writel_relaxed(0xffffffff, se->base + SE_DMA_TX_IRQ_CLR); + writel_relaxed(0xffffffff, se->base + SE_DMA_RX_IRQ_CLR); + writel_relaxed(0xffffffff, se->base + SE_IRQ_EN); + + val = readl_relaxed(se->base + SE_GENI_DMA_MODE_EN); + val |= GENI_DMA_MODE_EN; + writel_relaxed(val, se->base + SE_GENI_DMA_MODE_EN); +} + +/** + * geni_se_select_mode() - Select the serial engine transfer mode + * @se: Pointer to the concerned serial engine. + * @mode: Transfer mode to be selected. + */ +void geni_se_select_mode(struct geni_se *se, enum geni_se_xfer_mode mode) +{ + WARN_ON(mode != GENI_SE_FIFO && mode != GENI_SE_DMA); + + switch (mode) { + case GENI_SE_FIFO: + geni_se_select_fifo_mode(se); + break; + case GENI_SE_DMA: + geni_se_select_dma_mode(se); + break; + case GENI_SE_INVALID: + default: + break; + } +} +EXPORT_SYMBOL(geni_se_select_mode); + +/** + * DOC: Overview + * + * GENI FIFO packing is highly configurable. TX/RX packing/unpacking consist + * of up to 4 operations, each operation represented by 4 configuration vectors + * of 10 bits programmed in GENI_TX_PACKING_CFG0 and GENI_TX_PACKING_CFG1 for + * TX FIFO and in GENI_RX_PACKING_CFG0 and GENI_RX_PACKING_CFG1 for RX FIFO. + * Refer to below examples for detailed bit-field description. + * + * Example 1: word_size = 7, packing_mode = 4 x 8, msb_to_lsb = 1 + * + * +-----------+-------+-------+-------+-------+ + * | | vec_0 | vec_1 | vec_2 | vec_3 | + * +-----------+-------+-------+-------+-------+ + * | start | 0x6 | 0xe | 0x16 | 0x1e | + * | direction | 1 | 1 | 1 | 1 | + * | length | 6 | 6 | 6 | 6 | + * | stop | 0 | 0 | 0 | 1 | + * +-----------+-------+-------+-------+-------+ + * + * Example 2: word_size = 15, packing_mode = 2 x 16, msb_to_lsb = 0 + * + * +-----------+-------+-------+-------+-------+ + * | | vec_0 | vec_1 | vec_2 | vec_3 | + * +-----------+-------+-------+-------+-------+ + * | start | 0x0 | 0x8 | 0x10 | 0x18 | + * | direction | 0 | 0 | 0 | 0 | + * | length | 7 | 6 | 7 | 6 | + * | stop | 0 | 0 | 0 | 1 | + * +-----------+-------+-------+-------+-------+ + * + * Example 3: word_size = 23, packing_mode = 1 x 32, msb_to_lsb = 1 + * + * +-----------+-------+-------+-------+-------+ + * | | vec_0 | vec_1 | vec_2 | vec_3 | + * +-----------+-------+-------+-------+-------+ + * | start | 0x16 | 0xe | 0x6 | 0x0 | + * | direction | 1 | 1 | 1 | 1 | + * | length | 7 | 7 | 6 | 0 | + * | stop | 0 | 0 | 1 | 0 | + * +-----------+-------+-------+-------+-------+ + * + */ + +#define NUM_PACKING_VECTORS 4 +#define PACKING_START_SHIFT 5 +#define PACKING_DIR_SHIFT 4 +#define PACKING_LEN_SHIFT 1 +#define PACKING_STOP_BIT BIT(0) +#define PACKING_VECTOR_SHIFT 10 +/** + * geni_se_config_packing() - Packing configuration of the serial engine + * @se: Pointer to the concerned serial engine + * @bpw: Bits of data per transfer word. + * @pack_words: Number of words per fifo element. + * @msb_to_lsb: Transfer from MSB to LSB or vice-versa. + * @tx_cfg: Flag to configure the TX Packing. + * @rx_cfg: Flag to configure the RX Packing. + * + * This function is used to configure the packing rules for the current + * transfer. + */ +void geni_se_config_packing(struct geni_se *se, int bpw, int pack_words, + bool msb_to_lsb, bool tx_cfg, bool rx_cfg) +{ + u32 cfg0, cfg1, cfg[NUM_PACKING_VECTORS] = {0}; + int len; + int temp_bpw = bpw; + int idx_start = msb_to_lsb ? bpw - 1 : 0; + int idx = idx_start; + int idx_delta = msb_to_lsb ? -BITS_PER_BYTE : BITS_PER_BYTE; + int ceil_bpw = ALIGN(bpw, BITS_PER_BYTE); + int iter = (ceil_bpw * pack_words) / BITS_PER_BYTE; + int i; + + if (iter <= 0 || iter > NUM_PACKING_VECTORS) + return; + + for (i = 0; i < iter; i++) { + len = min_t(int, temp_bpw, BITS_PER_BYTE) - 1; + cfg[i] = idx << PACKING_START_SHIFT; + cfg[i] |= msb_to_lsb << PACKING_DIR_SHIFT; + cfg[i] |= len << PACKING_LEN_SHIFT; + + if (temp_bpw <= BITS_PER_BYTE) { + idx = ((i + 1) * BITS_PER_BYTE) + idx_start; + temp_bpw = bpw; + } else { + idx = idx + idx_delta; + temp_bpw = temp_bpw - BITS_PER_BYTE; + } + } + cfg[iter - 1] |= PACKING_STOP_BIT; + cfg0 = cfg[0] | (cfg[1] << PACKING_VECTOR_SHIFT); + cfg1 = cfg[2] | (cfg[3] << PACKING_VECTOR_SHIFT); + + if (tx_cfg) { + writel_relaxed(cfg0, se->base + SE_GENI_TX_PACKING_CFG0); + writel_relaxed(cfg1, se->base + SE_GENI_TX_PACKING_CFG1); + } + if (rx_cfg) { + writel_relaxed(cfg0, se->base + SE_GENI_RX_PACKING_CFG0); + writel_relaxed(cfg1, se->base + SE_GENI_RX_PACKING_CFG1); + } + + /* + * Number of protocol words in each FIFO entry + * 0 - 4x8, four words in each entry, max word size of 8 bits + * 1 - 2x16, two words in each entry, max word size of 16 bits + * 2 - 1x32, one word in each entry, max word size of 32 bits + * 3 - undefined + */ + if (pack_words || bpw == 32) + writel_relaxed(bpw / 16, se->base + SE_GENI_BYTE_GRAN); +} +EXPORT_SYMBOL(geni_se_config_packing); + +static void geni_se_clks_off(struct geni_se *se) +{ + struct geni_wrapper *wrapper = se->wrapper; + + clk_disable_unprepare(se->clk); + clk_bulk_disable_unprepare(ARRAY_SIZE(wrapper->ahb_clks), + wrapper->ahb_clks); +} + +/** + * geni_se_resources_off() - Turn off resources associated with the serial + * engine + * @se: Pointer to the concerned serial engine. + * + * Return: 0 on success, standard Linux error codes on failure/error. + */ +int geni_se_resources_off(struct geni_se *se) +{ + int ret; + + ret = pinctrl_pm_select_sleep_state(se->dev); + if (ret) + return ret; + + geni_se_clks_off(se); + return 0; +} +EXPORT_SYMBOL(geni_se_resources_off); + +static int geni_se_clks_on(struct geni_se *se) +{ + int ret; + struct geni_wrapper *wrapper = se->wrapper; + + ret = clk_bulk_prepare_enable(ARRAY_SIZE(wrapper->ahb_clks), + wrapper->ahb_clks); + if (ret) + return ret; + + ret = clk_prepare_enable(se->clk); + if (ret) + clk_bulk_disable_unprepare(ARRAY_SIZE(wrapper->ahb_clks), + wrapper->ahb_clks); + return ret; +} + +/** + * geni_se_resources_on() - Turn on resources associated with the serial + * engine + * @se: Pointer to the concerned serial engine. + * + * Return: 0 on success, standard Linux error codes on failure/error. + */ +int geni_se_resources_on(struct geni_se *se) +{ + int ret; + + ret = geni_se_clks_on(se); + if (ret) + return ret; + + ret = pinctrl_pm_select_default_state(se->dev); + if (ret) + geni_se_clks_off(se); + + return ret; +} +EXPORT_SYMBOL(geni_se_resources_on); + +/** + * geni_se_clk_tbl_get() - Get the clock table to program DFS + * @se: Pointer to the concerned serial engine. + * @tbl: Table in which the output is returned. + * + * This function is called by the protocol drivers to determine the different + * clock frequencies supported by serial engine core clock. The protocol + * drivers use the output to determine the clock frequency index to be + * programmed into DFS. + * + * Return: number of valid performance levels in the table on success, + * standard Linux error codes on failure. + */ +int geni_se_clk_tbl_get(struct geni_se *se, unsigned long **tbl) +{ + unsigned long freq = 0; + int i; + + if (se->clk_perf_tbl) { + *tbl = se->clk_perf_tbl; + return se->num_clk_levels; + } + + se->clk_perf_tbl = devm_kcalloc(se->dev, MAX_CLK_PERF_LEVEL, + sizeof(*se->clk_perf_tbl), + GFP_KERNEL); + if (!se->clk_perf_tbl) + return -ENOMEM; + + for (i = 0; i < MAX_CLK_PERF_LEVEL; i++) { + freq = clk_round_rate(se->clk, freq + 1); + if (!freq || freq == se->clk_perf_tbl[i - 1]) + break; + se->clk_perf_tbl[i] = freq; + } + se->num_clk_levels = i; + *tbl = se->clk_perf_tbl; + return se->num_clk_levels; +} +EXPORT_SYMBOL(geni_se_clk_tbl_get); + +/** + * geni_se_clk_freq_match() - Get the matching or closest SE clock frequency + * @se: Pointer to the concerned serial engine. + * @req_freq: Requested clock frequency. + * @index: Index of the resultant frequency in the table. + * @res_freq: Resultant frequency which matches or is closer to the + * requested frequency. + * @exact: Flag to indicate exact multiple requirement of the requested + * frequency. + * + * This function is called by the protocol drivers to determine the matching + * or exact multiple of the requested frequency, as provided by the serial + * engine clock in order to meet the performance requirements. If there is + * no matching or exact multiple of the requested frequency found, then it + * selects the closest floor frequency, if exact flag is not set. + * + * Return: 0 on success, standard Linux error codes on failure. + */ +int geni_se_clk_freq_match(struct geni_se *se, unsigned long req_freq, + unsigned int *index, unsigned long *res_freq, + bool exact) +{ + unsigned long *tbl; + int num_clk_levels; + int i; + + num_clk_levels = geni_se_clk_tbl_get(se, &tbl); + if (num_clk_levels < 0) + return num_clk_levels; + + if (num_clk_levels == 0) + return -EINVAL; + + *res_freq = 0; + for (i = 0; i < num_clk_levels; i++) { + if (!(tbl[i] % req_freq)) { + *index = i; + *res_freq = tbl[i]; + return 0; + } + + if (!(*res_freq) || ((tbl[i] > *res_freq) && + (tbl[i] < req_freq))) { + *index = i; + *res_freq = tbl[i]; + } + } + + if (exact) + return -EINVAL; + + return 0; +} +EXPORT_SYMBOL(geni_se_clk_freq_match); + +#define GENI_SE_DMA_DONE_EN BIT(0) +#define GENI_SE_DMA_EOT_EN BIT(1) +#define GENI_SE_DMA_AHB_ERR_EN BIT(2) +#define GENI_SE_DMA_EOT_BUF BIT(0) +/** + * geni_se_tx_dma_prep() - Prepare the serial engine for TX DMA transfer + * @se: Pointer to the concerned serial engine. + * @buf: Pointer to the TX buffer. + * @len: Length of the TX buffer. + * @iova: Pointer to store the mapped DMA address. + * + * This function is used to prepare the buffers for DMA TX. + * + * Return: 0 on success, standard Linux error codes on failure. + */ +int geni_se_tx_dma_prep(struct geni_se *se, void *buf, size_t len, + dma_addr_t *iova) +{ + struct geni_wrapper *wrapper = se->wrapper; + u32 val; + + *iova = dma_map_single(wrapper->dev, buf, len, DMA_TO_DEVICE); + if (dma_mapping_error(wrapper->dev, *iova)) + return -EIO; + + val = GENI_SE_DMA_DONE_EN; + val |= GENI_SE_DMA_EOT_EN; + val |= GENI_SE_DMA_AHB_ERR_EN; + writel_relaxed(val, se->base + SE_DMA_TX_IRQ_EN_SET); + writel_relaxed(lower_32_bits(*iova), se->base + SE_DMA_TX_PTR_L); + writel_relaxed(upper_32_bits(*iova), se->base + SE_DMA_TX_PTR_H); + writel_relaxed(GENI_SE_DMA_EOT_BUF, se->base + SE_DMA_TX_ATTR); + writel_relaxed(len, se->base + SE_DMA_TX_LEN); + return 0; +} +EXPORT_SYMBOL(geni_se_tx_dma_prep); + +/** + * geni_se_rx_dma_prep() - Prepare the serial engine for RX DMA transfer + * @se: Pointer to the concerned serial engine. + * @buf: Pointer to the RX buffer. + * @len: Length of the RX buffer. + * @iova: Pointer to store the mapped DMA address. + * + * This function is used to prepare the buffers for DMA RX. + * + * Return: 0 on success, standard Linux error codes on failure. + */ +int geni_se_rx_dma_prep(struct geni_se *se, void *buf, size_t len, + dma_addr_t *iova) +{ + struct geni_wrapper *wrapper = se->wrapper; + u32 val; + + *iova = dma_map_single(wrapper->dev, buf, len, DMA_FROM_DEVICE); + if (dma_mapping_error(wrapper->dev, *iova)) + return -EIO; + + val = GENI_SE_DMA_DONE_EN; + val |= GENI_SE_DMA_EOT_EN; + val |= GENI_SE_DMA_AHB_ERR_EN; + writel_relaxed(val, se->base + SE_DMA_RX_IRQ_EN_SET); + writel_relaxed(lower_32_bits(*iova), se->base + SE_DMA_RX_PTR_L); + writel_relaxed(upper_32_bits(*iova), se->base + SE_DMA_RX_PTR_H); + /* RX does not have EOT buffer type bit. So just reset RX_ATTR */ + writel_relaxed(0, se->base + SE_DMA_RX_ATTR); + writel_relaxed(len, se->base + SE_DMA_RX_LEN); + return 0; +} +EXPORT_SYMBOL(geni_se_rx_dma_prep); + +/** + * geni_se_tx_dma_unprep() - Unprepare the serial engine after TX DMA transfer + * @se: Pointer to the concerned serial engine. + * @iova: DMA address of the TX buffer. + * @len: Length of the TX buffer. + * + * This function is used to unprepare the DMA buffers after DMA TX. + */ +void geni_se_tx_dma_unprep(struct geni_se *se, dma_addr_t iova, size_t len) +{ + struct geni_wrapper *wrapper = se->wrapper; + + if (iova && !dma_mapping_error(wrapper->dev, iova)) + dma_unmap_single(wrapper->dev, iova, len, DMA_TO_DEVICE); +} +EXPORT_SYMBOL(geni_se_tx_dma_unprep); + +/** + * geni_se_rx_dma_unprep() - Unprepare the serial engine after RX DMA transfer + * @se: Pointer to the concerned serial engine. + * @iova: DMA address of the RX buffer. + * @len: Length of the RX buffer. + * + * This function is used to unprepare the DMA buffers after DMA RX. + */ +void geni_se_rx_dma_unprep(struct geni_se *se, dma_addr_t iova, size_t len) +{ + struct geni_wrapper *wrapper = se->wrapper; + + if (iova && !dma_mapping_error(wrapper->dev, iova)) + dma_unmap_single(wrapper->dev, iova, len, DMA_FROM_DEVICE); +} +EXPORT_SYMBOL(geni_se_rx_dma_unprep); + +static int geni_se_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct resource *res; + struct geni_wrapper *wrapper; + int ret; + + wrapper = devm_kzalloc(dev, sizeof(*wrapper), GFP_KERNEL); + if (!wrapper) + return -ENOMEM; + + wrapper->dev = dev; + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + wrapper->base = devm_ioremap_resource(dev, res); + if (IS_ERR(wrapper->base)) + return PTR_ERR(wrapper->base); + + wrapper->ahb_clks[0].id = "m-ahb"; + wrapper->ahb_clks[1].id = "s-ahb"; + ret = devm_clk_bulk_get(dev, NUM_AHB_CLKS, wrapper->ahb_clks); + if (ret) { + dev_err(dev, "Err getting AHB clks %d\n", ret); + return ret; + } + + dev_set_drvdata(dev, wrapper); + dev_dbg(dev, "GENI SE Driver probed\n"); + return devm_of_platform_populate(dev); +} + +static const struct of_device_id geni_se_dt_match[] = { + { .compatible = "qcom,geni-se-qup", }, + {} +}; +MODULE_DEVICE_TABLE(of, geni_se_dt_match); + +static struct platform_driver geni_se_driver = { + .driver = { + .name = "geni_se_qup", + .of_match_table = geni_se_dt_match, + }, + .probe = geni_se_probe, +}; +module_platform_driver(geni_se_driver); + +MODULE_DESCRIPTION("GENI Serial Engine Driver"); +MODULE_LICENSE("GPL v2"); diff --git a/include/linux/qcom-geni-se.h b/include/linux/qcom-geni-se.h new file mode 100644 index 000000000000..5d6144977828 --- /dev/null +++ b/include/linux/qcom-geni-se.h @@ -0,0 +1,425 @@ +/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */ +/* + * Copyright (c) 2017-2018, The Linux Foundation. All rights reserved. + */ + +#ifndef _LINUX_QCOM_GENI_SE +#define _LINUX_QCOM_GENI_SE + +/* Transfer mode supported by GENI Serial Engines */ +enum geni_se_xfer_mode { + GENI_SE_INVALID, + GENI_SE_FIFO, + GENI_SE_DMA, +}; + +/* Protocols supported by GENI Serial Engines */ +enum geni_se_protocol_type { + GENI_SE_NONE, + GENI_SE_SPI, + GENI_SE_UART, + GENI_SE_I2C, + GENI_SE_I3C, +}; + +struct geni_wrapper; +struct clk; + +/** + * struct geni_se - GENI Serial Engine + * @base: Base Address of the Serial Engine's register block + * @dev: Pointer to the Serial Engine device + * @wrapper: Pointer to the parent QUP Wrapper core + * @clk: Handle to the core serial engine clock + * @num_clk_levels: Number of valid clock levels in clk_perf_tbl + * @clk_perf_tbl: Table of clock frequency input to serial engine clock + */ +struct geni_se { + void __iomem *base; + struct device *dev; + struct geni_wrapper *wrapper; + struct clk *clk; + unsigned int num_clk_levels; + unsigned long *clk_perf_tbl; +}; + +/* Common SE registers */ +#define GENI_FORCE_DEFAULT_REG 0x20 +#define SE_GENI_STATUS 0x40 +#define GENI_SER_M_CLK_CFG 0x48 +#define GENI_SER_S_CLK_CFG 0x4c +#define GENI_FW_REVISION_RO 0x68 +#define SE_GENI_CLK_SEL 0x7c +#define SE_GENI_DMA_MODE_EN 0x258 +#define SE_GENI_M_CMD0 0x600 +#define SE_GENI_M_CMD_CTRL_REG 0x604 +#define SE_GENI_M_IRQ_STATUS 0x610 +#define SE_GENI_M_IRQ_EN 0x614 +#define SE_GENI_M_IRQ_CLEAR 0x618 +#define SE_GENI_S_CMD0 0x630 +#define SE_GENI_S_CMD_CTRL_REG 0x634 +#define SE_GENI_S_IRQ_STATUS 0x640 +#define SE_GENI_S_IRQ_EN 0x644 +#define SE_GENI_S_IRQ_CLEAR 0x648 +#define SE_GENI_TX_FIFOn 0x700 +#define SE_GENI_RX_FIFOn 0x780 +#define SE_GENI_TX_FIFO_STATUS 0x800 +#define SE_GENI_RX_FIFO_STATUS 0x804 +#define SE_GENI_TX_WATERMARK_REG 0x80c +#define SE_GENI_RX_WATERMARK_REG 0x810 +#define SE_GENI_RX_RFR_WATERMARK_REG 0x814 +#define SE_GENI_IOS 0x908 +#define SE_DMA_TX_IRQ_STAT 0xc40 +#define SE_DMA_TX_IRQ_CLR 0xc44 +#define SE_DMA_TX_FSM_RST 0xc58 +#define SE_DMA_RX_IRQ_STAT 0xd40 +#define SE_DMA_RX_IRQ_CLR 0xd44 +#define SE_DMA_RX_FSM_RST 0xd58 +#define SE_HW_PARAM_0 0xe24 +#define SE_HW_PARAM_1 0xe28 + +/* GENI_FORCE_DEFAULT_REG fields */ +#define FORCE_DEFAULT BIT(0) + +/* GENI_STATUS fields */ +#define M_GENI_CMD_ACTIVE BIT(0) +#define S_GENI_CMD_ACTIVE BIT(12) + +/* GENI_SER_M_CLK_CFG/GENI_SER_S_CLK_CFG */ +#define SER_CLK_EN BIT(0) +#define CLK_DIV_MSK GENMASK(15, 4) +#define CLK_DIV_SHFT 4 + +/* GENI_FW_REVISION_RO fields */ +#define FW_REV_PROTOCOL_MSK GENMASK(15, 8) +#define FW_REV_PROTOCOL_SHFT 8 + +/* GENI_CLK_SEL fields */ +#define CLK_SEL_MSK GENMASK(2, 0) + +/* SE_GENI_DMA_MODE_EN */ +#define GENI_DMA_MODE_EN BIT(0) + +/* GENI_M_CMD0 fields */ +#define M_OPCODE_MSK GENMASK(31, 27) +#define M_OPCODE_SHFT 27 +#define M_PARAMS_MSK GENMASK(26, 0) + +/* GENI_M_CMD_CTRL_REG */ +#define M_GENI_CMD_CANCEL BIT(2) +#define M_GENI_CMD_ABORT BIT(1) +#define M_GENI_DISABLE BIT(0) + +/* GENI_S_CMD0 fields */ +#define S_OPCODE_MSK GENMASK(31, 27) +#define S_OPCODE_SHFT 27 +#define S_PARAMS_MSK GENMASK(26, 0) + +/* GENI_S_CMD_CTRL_REG */ +#define S_GENI_CMD_CANCEL BIT(2) +#define S_GENI_CMD_ABORT BIT(1) +#define S_GENI_DISABLE BIT(0) + +/* GENI_M_IRQ_EN fields */ +#define M_CMD_DONE_EN BIT(0) +#define M_CMD_OVERRUN_EN BIT(1) +#define M_ILLEGAL_CMD_EN BIT(2) +#define M_CMD_FAILURE_EN BIT(3) +#define M_CMD_CANCEL_EN BIT(4) +#define M_CMD_ABORT_EN BIT(5) +#define M_TIMESTAMP_EN BIT(6) +#define M_RX_IRQ_EN BIT(7) +#define M_GP_SYNC_IRQ_0_EN BIT(8) +#define M_GP_IRQ_0_EN BIT(9) +#define M_GP_IRQ_1_EN BIT(10) +#define M_GP_IRQ_2_EN BIT(11) +#define M_GP_IRQ_3_EN BIT(12) +#define M_GP_IRQ_4_EN BIT(13) +#define M_GP_IRQ_5_EN BIT(14) +#define M_IO_DATA_DEASSERT_EN BIT(22) +#define M_IO_DATA_ASSERT_EN BIT(23) +#define M_RX_FIFO_RD_ERR_EN BIT(24) +#define M_RX_FIFO_WR_ERR_EN BIT(25) +#define M_RX_FIFO_WATERMARK_EN BIT(26) +#define M_RX_FIFO_LAST_EN BIT(27) +#define M_TX_FIFO_RD_ERR_EN BIT(28) +#define M_TX_FIFO_WR_ERR_EN BIT(29) +#define M_TX_FIFO_WATERMARK_EN BIT(30) +#define M_SEC_IRQ_EN BIT(31) +#define M_COMMON_GENI_M_IRQ_EN (GENMASK(6, 1) | \ + M_IO_DATA_DEASSERT_EN | \ + M_IO_DATA_ASSERT_EN | M_RX_FIFO_RD_ERR_EN | \ + M_RX_FIFO_WR_ERR_EN | M_TX_FIFO_RD_ERR_EN | \ + M_TX_FIFO_WR_ERR_EN) + +/* GENI_S_IRQ_EN fields */ +#define S_CMD_DONE_EN BIT(0) +#define S_CMD_OVERRUN_EN BIT(1) +#define S_ILLEGAL_CMD_EN BIT(2) +#define S_CMD_FAILURE_EN BIT(3) +#define S_CMD_CANCEL_EN BIT(4) +#define S_CMD_ABORT_EN BIT(5) +#define S_GP_SYNC_IRQ_0_EN BIT(8) +#define S_GP_IRQ_0_EN BIT(9) +#define S_GP_IRQ_1_EN BIT(10) +#define S_GP_IRQ_2_EN BIT(11) +#define S_GP_IRQ_3_EN BIT(12) +#define S_GP_IRQ_4_EN BIT(13) +#define S_GP_IRQ_5_EN BIT(14) +#define S_IO_DATA_DEASSERT_EN BIT(22) +#define S_IO_DATA_ASSERT_EN BIT(23) +#define S_RX_FIFO_RD_ERR_EN BIT(24) +#define S_RX_FIFO_WR_ERR_EN BIT(25) +#define S_RX_FIFO_WATERMARK_EN BIT(26) +#define S_RX_FIFO_LAST_EN BIT(27) +#define S_COMMON_GENI_S_IRQ_EN (GENMASK(5, 1) | GENMASK(13, 9) | \ + S_RX_FIFO_RD_ERR_EN | S_RX_FIFO_WR_ERR_EN) + +/* GENI_/TX/RX/RX_RFR/_WATERMARK_REG fields */ +#define WATERMARK_MSK GENMASK(5, 0) + +/* GENI_TX_FIFO_STATUS fields */ +#define TX_FIFO_WC GENMASK(27, 0) + +/* GENI_RX_FIFO_STATUS fields */ +#define RX_LAST BIT(31) +#define RX_LAST_BYTE_VALID_MSK GENMASK(30, 28) +#define RX_LAST_BYTE_VALID_SHFT 28 +#define RX_FIFO_WC_MSK GENMASK(24, 0) + +/* SE_GENI_IOS fields */ +#define IO2_DATA_IN BIT(1) +#define RX_DATA_IN BIT(0) + +/* SE_DMA_TX_IRQ_STAT Register fields */ +#define TX_DMA_DONE BIT(0) +#define TX_EOT BIT(1) +#define TX_SBE BIT(2) +#define TX_RESET_DONE BIT(3) + +/* SE_DMA_RX_IRQ_STAT Register fields */ +#define RX_DMA_DONE BIT(0) +#define RX_EOT BIT(1) +#define RX_SBE BIT(2) +#define RX_RESET_DONE BIT(3) +#define RX_FLUSH_DONE BIT(4) +#define RX_GENI_GP_IRQ GENMASK(10, 5) +#define RX_GENI_CANCEL_IRQ BIT(11) +#define RX_GENI_GP_IRQ_EXT GENMASK(13, 12) + +/* SE_HW_PARAM_0 fields */ +#define TX_FIFO_WIDTH_MSK GENMASK(29, 24) +#define TX_FIFO_WIDTH_SHFT 24 +#define TX_FIFO_DEPTH_MSK GENMASK(21, 16) +#define TX_FIFO_DEPTH_SHFT 16 + +/* SE_HW_PARAM_1 fields */ +#define RX_FIFO_WIDTH_MSK GENMASK(29, 24) +#define RX_FIFO_WIDTH_SHFT 24 +#define RX_FIFO_DEPTH_MSK GENMASK(21, 16) +#define RX_FIFO_DEPTH_SHFT 16 + +#define HW_VER_MAJOR_MASK GENMASK(31, 28) +#define HW_VER_MAJOR_SHFT 28 +#define HW_VER_MINOR_MASK GENMASK(27, 16) +#define HW_VER_MINOR_SHFT 16 +#define HW_VER_STEP_MASK GENMASK(15, 0) + +#if IS_ENABLED(CONFIG_QCOM_GENI_SE) + +u32 geni_se_get_qup_hw_version(struct geni_se *se); + +#define geni_se_get_wrapper_version(se, major, minor, step) do { \ + u32 ver; \ +\ + ver = geni_se_get_qup_hw_version(se); \ + major = (ver & HW_VER_MAJOR_MASK) >> HW_VER_MAJOR_SHFT; \ + minor = (ver & HW_VER_MINOR_MASK) >> HW_VER_MINOR_SHFT; \ + step = version & HW_VER_STEP_MASK; \ +} while (0) + +/** + * geni_se_read_proto() - Read the protocol configured for a serial engine + * @se: Pointer to the concerned serial engine. + * + * Return: Protocol value as configured in the serial engine. + */ +static inline u32 geni_se_read_proto(struct geni_se *se) +{ + u32 val; + + val = readl_relaxed(se->base + GENI_FW_REVISION_RO); + + return (val & FW_REV_PROTOCOL_MSK) >> FW_REV_PROTOCOL_SHFT; +} + +/** + * geni_se_setup_m_cmd() - Setup the primary sequencer + * @se: Pointer to the concerned serial engine. + * @cmd: Command/Operation to setup in the primary sequencer. + * @params: Parameter for the sequencer command. + * + * This function is used to configure the primary sequencer with the + * command and its associated parameters. + */ +static inline void geni_se_setup_m_cmd(struct geni_se *se, u32 cmd, u32 params) +{ + u32 m_cmd; + + m_cmd = (cmd << M_OPCODE_SHFT) | (params & M_PARAMS_MSK); + writel_relaxed(m_cmd, se->base + SE_GENI_M_CMD0); +} + +/** + * geni_se_setup_s_cmd() - Setup the secondary sequencer + * @se: Pointer to the concerned serial engine. + * @cmd: Command/Operation to setup in the secondary sequencer. + * @params: Parameter for the sequencer command. + * + * This function is used to configure the secondary sequencer with the + * command and its associated parameters. + */ +static inline void geni_se_setup_s_cmd(struct geni_se *se, u32 cmd, u32 params) +{ + u32 s_cmd; + + s_cmd = readl_relaxed(se->base + SE_GENI_S_CMD0); + s_cmd &= ~(S_OPCODE_MSK | S_PARAMS_MSK); + s_cmd |= (cmd << S_OPCODE_SHFT); + s_cmd |= (params & S_PARAMS_MSK); + writel_relaxed(s_cmd, se->base + SE_GENI_S_CMD0); +} + +/** + * geni_se_cancel_m_cmd() - Cancel the command configured in the primary + * sequencer + * @se: Pointer to the concerned serial engine. + * + * This function is used to cancel the currently configured command in the + * primary sequencer. + */ +static inline void geni_se_cancel_m_cmd(struct geni_se *se) +{ + writel_relaxed(M_GENI_CMD_CANCEL, se->base + SE_GENI_M_CMD_CTRL_REG); +} + +/** + * geni_se_cancel_s_cmd() - Cancel the command configured in the secondary + * sequencer + * @se: Pointer to the concerned serial engine. + * + * This function is used to cancel the currently configured command in the + * secondary sequencer. + */ +static inline void geni_se_cancel_s_cmd(struct geni_se *se) +{ + writel_relaxed(S_GENI_CMD_CANCEL, se->base + SE_GENI_S_CMD_CTRL_REG); +} + +/** + * geni_se_abort_m_cmd() - Abort the command configured in the primary sequencer + * @se: Pointer to the concerned serial engine. + * + * This function is used to force abort the currently configured command in the + * primary sequencer. + */ +static inline void geni_se_abort_m_cmd(struct geni_se *se) +{ + writel_relaxed(M_GENI_CMD_ABORT, se->base + SE_GENI_M_CMD_CTRL_REG); +} + +/** + * geni_se_abort_s_cmd() - Abort the command configured in the secondary + * sequencer + * @se: Pointer to the concerned serial engine. + * + * This function is used to force abort the currently configured command in the + * secondary sequencer. + */ +static inline void geni_se_abort_s_cmd(struct geni_se *se) +{ + writel_relaxed(S_GENI_CMD_ABORT, se->base + SE_GENI_S_CMD_CTRL_REG); +} + +/** + * geni_se_get_tx_fifo_depth() - Get the TX fifo depth of the serial engine + * @se: Pointer to the concerned serial engine. + * + * This function is used to get the depth i.e. number of elements in the + * TX fifo of the serial engine. + * + * Return: TX fifo depth in units of FIFO words. + */ +static inline u32 geni_se_get_tx_fifo_depth(struct geni_se *se) +{ + u32 val; + + val = readl_relaxed(se->base + SE_HW_PARAM_0); + + return (val & TX_FIFO_DEPTH_MSK) >> TX_FIFO_DEPTH_SHFT; +} + +/** + * geni_se_get_tx_fifo_width() - Get the TX fifo width of the serial engine + * @se: Pointer to the concerned serial engine. + * + * This function is used to get the width i.e. word size per element in the + * TX fifo of the serial engine. + * + * Return: TX fifo width in bits + */ +static inline u32 geni_se_get_tx_fifo_width(struct geni_se *se) +{ + u32 val; + + val = readl_relaxed(se->base + SE_HW_PARAM_0); + + return (val & TX_FIFO_WIDTH_MSK) >> TX_FIFO_WIDTH_SHFT; +} + +/** + * geni_se_get_rx_fifo_depth() - Get the RX fifo depth of the serial engine + * @se: Pointer to the concerned serial engine. + * + * This function is used to get the depth i.e. number of elements in the + * RX fifo of the serial engine. + * + * Return: RX fifo depth in units of FIFO words + */ +static inline u32 geni_se_get_rx_fifo_depth(struct geni_se *se) +{ + u32 val; + + val = readl_relaxed(se->base + SE_HW_PARAM_1); + + return (val & RX_FIFO_DEPTH_MSK) >> RX_FIFO_DEPTH_SHFT; +} + +void geni_se_init(struct geni_se *se, u32 rx_wm, u32 rx_rfr); + +void geni_se_select_mode(struct geni_se *se, enum geni_se_xfer_mode mode); + +void geni_se_config_packing(struct geni_se *se, int bpw, int pack_words, + bool msb_to_lsb, bool tx_cfg, bool rx_cfg); + +int geni_se_resources_off(struct geni_se *se); + +int geni_se_resources_on(struct geni_se *se); + +int geni_se_clk_tbl_get(struct geni_se *se, unsigned long **tbl); + +int geni_se_clk_freq_match(struct geni_se *se, unsigned long req_freq, + unsigned int *index, unsigned long *res_freq, + bool exact); + +int geni_se_tx_dma_prep(struct geni_se *se, void *buf, size_t len, + dma_addr_t *iova); + +int geni_se_rx_dma_prep(struct geni_se *se, void *buf, size_t len, + dma_addr_t *iova); + +void geni_se_tx_dma_unprep(struct geni_se *se, dma_addr_t iova, size_t len); + +void geni_se_rx_dma_unprep(struct geni_se *se, dma_addr_t iova, size_t len); +#endif +#endif |