diff options
| -rw-r--r-- | Documentation/devicetree/bindings/net/davinci-mdio.txt | 8 | ||||
| -rw-r--r-- | drivers/net/ethernet/ti/Kconfig | 4 | ||||
| -rw-r--r-- | drivers/net/ethernet/ti/davinci_mdio.c | 21 |
3 files changed, 25 insertions, 8 deletions
diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt index 72efaaf764f7..0369e25aabd2 100644 --- a/Documentation/devicetree/bindings/net/davinci-mdio.txt +++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt @@ -1,8 +1,8 @@ -TI SoC Davinci MDIO Controller Device Tree Bindings +TI SoC Davinci/Keystone2 MDIO Controller Device Tree Bindings --------------------------------------------------- Required properties: -- compatible : Should be "ti,davinci_mdio" +- compatible : Should be "ti,davinci_mdio" or "ti,keystone_mdio" - reg : physical base address and size of the davinci mdio registers map - bus_freq : Mdio Bus frequency @@ -19,7 +19,7 @@ file. Examples: mdio: davinci_mdio@4A101000 { - compatible = "ti,cpsw"; + compatible = "ti,davinci_mdio"; reg = <0x4A101000 0x1000>; bus_freq = <1000000>; }; @@ -27,7 +27,7 @@ Examples: (or) mdio: davinci_mdio@4A101000 { - compatible = "ti,cpsw"; + compatible = "ti,davinci_mdio"; ti,hwmods = "davinci_mdio"; bus_freq = <1000000>; }; diff --git a/drivers/net/ethernet/ti/Kconfig b/drivers/net/ethernet/ti/Kconfig index 53150c25a96b..1769700a6070 100644 --- a/drivers/net/ethernet/ti/Kconfig +++ b/drivers/net/ethernet/ti/Kconfig @@ -5,7 +5,7 @@ config NET_VENDOR_TI bool "Texas Instruments (TI) devices" default y - depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX)) + depends on PCI || EISA || AR7 || (ARM && (ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE)) ---help--- If you have a network (Ethernet) card belonging to this class, say Y and read the Ethernet-HOWTO, available from @@ -32,7 +32,7 @@ config TI_DAVINCI_EMAC config TI_DAVINCI_MDIO tristate "TI DaVinci MDIO Support" - depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX ) + depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 || SOC_AM33XX || ARCH_KEYSTONE ) select PHYLIB ---help--- This driver supports TI's DaVinci MDIO module. diff --git a/drivers/net/ethernet/ti/davinci_mdio.c b/drivers/net/ethernet/ti/davinci_mdio.c index 735dc53d4b01..2791f6f2db11 100644 --- a/drivers/net/ethernet/ti/davinci_mdio.c +++ b/drivers/net/ethernet/ti/davinci_mdio.c @@ -38,6 +38,7 @@ #include <linux/davinci_emac.h> #include <linux/of.h> #include <linux/of_device.h> +#include <linux/of_mdio.h> #include <linux/pinctrl/consumer.h> /* @@ -95,6 +96,10 @@ struct davinci_mdio_data { struct mii_bus *bus; bool suspended; unsigned long access_time; /* jiffies */ + /* Indicates that driver shouldn't modify phy_mask in case + * if MDIO bus is registered from DT. + */ + bool skip_scan; }; static void __davinci_mdio_reset(struct davinci_mdio_data *data) @@ -144,6 +149,9 @@ static int davinci_mdio_reset(struct mii_bus *bus) dev_info(data->dev, "davinci mdio revision %d.%d\n", (ver >> 8) & 0xff, ver & 0xff); + if (data->skip_scan) + return 0; + /* get phy mask from the alive register */ phy_mask = __raw_readl(&data->regs->alive); if (phy_mask) { @@ -369,8 +377,17 @@ static int davinci_mdio_probe(struct platform_device *pdev) goto bail_out; } - /* register the mii bus */ - ret = mdiobus_register(data->bus); + /* register the mii bus + * Create PHYs from DT only in case if PHY child nodes are explicitly + * defined to support backward compatibility with DTs which assume that + * Davinci MDIO will always scan the bus for PHYs detection. + */ + if (dev->of_node && of_get_child_count(dev->of_node)) { + data->skip_scan = true; + ret = of_mdiobus_register(data->bus, dev->of_node); + } else { + ret = mdiobus_register(data->bus); + } if (ret) goto bail_out; |