diff options
Diffstat (limited to 'Documentation/devicetree')
12 files changed, 208 insertions, 12 deletions
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,sgmiisys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,sgmiisys.txt index 30cb645c0e54..f5518f26a914 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,sgmiisys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,sgmiisys.txt @@ -9,6 +9,8 @@ Required Properties: - "mediatek,mt7622-sgmiisys", "syscon" - "mediatek,mt7629-sgmiisys", "syscon" - #clock-cells: Must be 1 +- mediatek,physpeed: Should be one of "auto", "1000" or "2500" to match up + the capability of the target PHY. The SGMIISYS controller uses the common clk binding from Documentation/devicetree/bindings/clock/clock-bindings.txt diff --git a/Documentation/devicetree/bindings/net/dsa/ksz.txt b/Documentation/devicetree/bindings/net/dsa/ksz.txt index e7db7268fd0f..4ac21cef370e 100644 --- a/Documentation/devicetree/bindings/net/dsa/ksz.txt +++ b/Documentation/devicetree/bindings/net/dsa/ksz.txt @@ -16,6 +16,8 @@ Required properties: Optional properties: - reset-gpios : Should be a gpio specifier for a reset line +- microchip,synclko-125 : Set if the output SYNCLKO frequency should be set to + 125MHz instead of 25MHz. See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional required and optional properties. diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt index feb007af13cb..6f9538974bb9 100644 --- a/Documentation/devicetree/bindings/net/dsa/marvell.txt +++ b/Documentation/devicetree/bindings/net/dsa/marvell.txt @@ -21,10 +21,13 @@ which is at a different MDIO base address in different switch families. 6341, 6350, 6351, 6352 - "marvell,mv88e6190" : Switch has base address 0x00. Use with models: 6190, 6190X, 6191, 6290, 6390, 6390X +- "marvell,mv88e6250" : Switch has base address 0x08 or 0x18. Use with model: + 6250 Required properties: -- compatible : Should be one of "marvell,mv88e6085" or - "marvell,mv88e6190" as indicated above +- compatible : Should be one of "marvell,mv88e6085", + "marvell,mv88e6190" or "marvell,mv88e6250" as + indicated above - reg : Address on the MII bus for the switch. Optional properties: diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt index e88c3641d613..5475682bf06e 100644 --- a/Documentation/devicetree/bindings/net/ethernet.txt +++ b/Documentation/devicetree/bindings/net/ethernet.txt @@ -43,6 +43,7 @@ Documentation/devicetree/bindings/phy/phy-bindings.txt. * "rxaui" * "xaui" * "10gbase-kr" (10GBASE-KR, XFI, SFI) + * "usxgmii" - phy-connection-type: the same as "phy-mode" property but described in the Devicetree Specification; - phy-handle: phandle, specifies a reference to a node representing a PHY diff --git a/Documentation/devicetree/bindings/net/keystone-netcp.txt b/Documentation/devicetree/bindings/net/keystone-netcp.txt index 6262c2f293b0..24f11e042f8d 100644 --- a/Documentation/devicetree/bindings/net/keystone-netcp.txt +++ b/Documentation/devicetree/bindings/net/keystone-netcp.txt @@ -104,6 +104,23 @@ Required properties: - 10Gb mac<->mac forced mode : 11 ----phy-handle: phandle to PHY device +- cpts: sub-node time synchronization (CPTS) submodule configuration +-- clocks: CPTS reference clock. Should point on cpts-refclk-mux clock. +-- clock-names: should be "cpts" +-- cpts-refclk-mux: multiplexer clock definition sub-node for CPTS reference (RFTCLK) clock +--- #clock-cells: should be 0 +--- clocks: list of CPTS reference (RFTCLK) clock's parents as defined in Data manual +--- ti,mux-tbl: array of multiplexer indexes as defined in Data manual +--- assigned-clocks: should point on cpts-refclk-mux clock +--- assigned-clock-parents: should point on required RFTCLK clock parent to be selected +-- cpts_clock_mult: (optional) Numerator to convert input clock ticks + into nanoseconds +-- cpts_clock_shift: (optional) Denominator to convert input clock ticks into + nanoseconds. + Mult and shift will be calculated basing on CPTS + rftclk frequency if both cpts_clock_shift and + cpts_clock_mult properties are not provided. + Optional properties: - enable-ale: NetCP driver keeps the address learning feature in the ethernet switch module disabled. This attribute is to enable the address @@ -168,6 +185,23 @@ netcp: netcp@2000000 { tx-queue = <648>; tx-channel = <8>; + cpts { + clocks = <&cpts_refclk_mux>; + clock-names = "cpts"; + + cpts_refclk_mux: cpts-refclk-mux { + #clock-cells = <0>; + clocks = <&chipclk12>, <&chipclk13>, + <&timi0>, <&timi1>, + <&tsipclka>, <&tsrefclk>, + <&tsipclkb>; + ti,mux-tbl = <0x0>, <0x1>, <0x2>, + <0x3>, <0x4>, <0x8>, <0xC>; + assigned-clocks = <&cpts_refclk_mux>; + assigned-clock-parents = <&chipclk12>; + }; + }; + interfaces { gbe0: interface-0 { slave-port = <0>; @@ -219,3 +253,13 @@ netcp: netcp@2000000 { }; }; }; + +CPTS board configuration - select external CPTS RFTCLK: + +&tsrefclk{ + clock-frequency = <500000000>; +}; + +&cpts_refclk_mux { + assigned-clock-parents = <&tsrefclk>; +}; diff --git a/Documentation/devicetree/bindings/net/mediatek-net.txt b/Documentation/devicetree/bindings/net/mediatek-net.txt index 503f2b9194e2..770ff98d4524 100644 --- a/Documentation/devicetree/bindings/net/mediatek-net.txt +++ b/Documentation/devicetree/bindings/net/mediatek-net.txt @@ -11,6 +11,7 @@ Required properties: "mediatek,mt2701-eth": for MT2701 SoC "mediatek,mt7623-eth", "mediatek,mt2701-eth": for MT7623 SoC "mediatek,mt7622-eth": for MT7622 SoC + "mediatek,mt7629-eth": for MT7629 SoC - reg: Address and length of the register set for the device - interrupts: Should contain the three frame engines interrupts in numeric order. These are fe_int0, fe_int1 and fe_int2. @@ -19,14 +20,23 @@ Required properties: "ethif", "esw", "gp2", "gp1" : For MT2701 and MT7623 SoC "ethif", "esw", "gp0", "gp1", "gp2", "sgmii_tx250m", "sgmii_rx250m", "sgmii_cdr_ref", "sgmii_cdr_fb", "sgmii_ck", "eth2pll" : For MT7622 SoC + "ethif", "sgmiitop", "esw", "gp0", "gp1", "gp2", "fe", "sgmii_tx250m", + "sgmii_rx250m", "sgmii_cdr_ref", "sgmii_cdr_fb", "sgmii2_tx250m", + "sgmii2_rx250m", "sgmii2_cdr_ref", "sgmii2_cdr_fb", "sgmii_ck", + "eth2pll" : For MT7629 SoC. - power-domains: phandle to the power domain that the ethernet is part of - resets: Should contain phandles to the ethsys reset signals - reset-names: Should contain the names of reset signal listed in the resets property These are "fe", "gmac" and "ppe" - mediatek,ethsys: phandle to the syscon node that handles the port setup -- mediatek,sgmiisys: phandle to the syscon node that handles the SGMII setup - which is required for those SoCs equipped with SGMII such as MT7622 SoC. +- mediatek,infracfg: phandle to the syscon node that handles the path from + GMAC to PHY variants, which is required for MT7629 SoC. +- mediatek,sgmiisys: a list of phandles to the syscon node that handles the + SGMII setup which is required for those SoCs equipped with SGMII such + as MT7622 and MT7629 SoC. And MT7622 have only one set of SGMII shared + by GMAC1 and GMAC2; MT7629 have two independent sets of SGMII directed + to GMAC1 and GMAC2, respectively. - mediatek,pctl: phandle to the syscon node that handles the ports slew rate and driver current: only for MT2701 and MT7623 SoC diff --git a/Documentation/devicetree/bindings/net/qca,ar71xx.txt b/Documentation/devicetree/bindings/net/qca,ar71xx.txt new file mode 100644 index 000000000000..2a33e71ba72b --- /dev/null +++ b/Documentation/devicetree/bindings/net/qca,ar71xx.txt @@ -0,0 +1,45 @@ +Required properties: +- compatible: Should be "qca,<soc>-eth". Currently support compatibles are: + qca,ar7100-eth - Atheros AR7100 + qca,ar7240-eth - Atheros AR7240 + qca,ar7241-eth - Atheros AR7241 + qca,ar7242-eth - Atheros AR7242 + qca,ar9130-eth - Atheros AR9130 + qca,ar9330-eth - Atheros AR9330 + qca,ar9340-eth - Atheros AR9340 + qca,qca9530-eth - Qualcomm Atheros QCA9530 + qca,qca9550-eth - Qualcomm Atheros QCA9550 + qca,qca9560-eth - Qualcomm Atheros QCA9560 + +- reg : Address and length of the register set for the device +- interrupts : Should contain eth interrupt +- phy-mode : See ethernet.txt file in the same directory +- clocks: the clock used by the core +- clock-names: the names of the clock listed in the clocks property. These are + "eth" and "mdio". +- resets: Should contain phandles to the reset signals +- reset-names: Should contain the names of reset signal listed in the resets + property. These are "mac" and "mdio" + +Optional properties: +- phy-handle : phandle to the PHY device connected to this device. +- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. + Use instead of phy-handle. + +Optional subnodes: +- mdio : specifies the mdio bus, used as a container for phy nodes + according to phy.txt in the same directory + +Example: + +ethernet@1a000000 { + compatible = "qca,ar9330-eth"; + reg = <0x1a000000 0x200>; + interrupts = <5>; + resets = <&rst 13>, <&rst 23>; + reset-names = "mac", "mdio"; + clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_MDIO>; + clock-names = "eth", "mdio"; + + phy-mode = "gmii"; +}; diff --git a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt index 17d6819669c8..612a8e8abc88 100644 --- a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt +++ b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt @@ -6,11 +6,17 @@ present in Documentation/devicetree/bindings/net/stmmac.txt. The device node has additional properties: Required properties: - - compatible : Should contain "altr,socfpga-stmmac" along with - "snps,dwmac" and any applicable more detailed + - compatible : For Cyclone5/Arria5 SoCs it should contain + "altr,socfpga-stmmac". For Arria10/Agilex/Stratix10 SoCs + "altr,socfpga-stmmac-a10-s10". + Along with "snps,dwmac" and any applicable more detailed designware version numbers documented in stmmac.txt - altr,sysmgr-syscon : Should be the phandle to the system manager node that encompasses the glue register, the register offset, and the register shift. + On Cyclone5/Arria5, the register shift represents the PHY mode bits, while + on the Arria10/Stratix10/Agilex platforms, the register shift represents + bit for each emac to enable/disable signals from the FPGA fabric to the + EMAC modules. - altr,f2h_ptp_ref_clk use f2h_ptp_ref_clk instead of default eosc1 clock for ptp ref clk. This affects all emacs as the clock is common. diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.txt b/Documentation/devicetree/bindings/net/ti,dp83867.txt index 9ef9338aaee1..db6aa3f2215b 100644 --- a/Documentation/devicetree/bindings/net/ti,dp83867.txt +++ b/Documentation/devicetree/bindings/net/ti,dp83867.txt @@ -11,6 +11,14 @@ Required properties: - ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h for applicable values +Note: If the interface type is PHY_INTERFACE_MODE_RGMII the TX/RX clock delays + will be left at their default values, as set by the PHY's pin strapping. + The default strapping will use a delay of 2.00 ns. Thus + PHY_INTERFACE_MODE_RGMII, by default, does not behave as RGMII with no + internal delay, but as PHY_INTERFACE_MODE_RGMII_ID. The device tree + should use "rgmii-id" if internal delays are desired as this may be + changed in future to cause "rgmii" mode to disable delays. + Optional property: - ti,min-output-impedance - MAC Interface Impedance control to set the programmable output impedance to @@ -25,8 +33,10 @@ Optional property: software needs to take when this pin is strapped in these modes. See data manual for details. - - ti,clk-output-sel - Muxing option for CLK_OUT pin - see dt-bindings/net/ti-dp83867.h - for applicable values. + - ti,clk-output-sel - Muxing option for CLK_OUT pin. See dt-bindings/net/ti-dp83867.h + for applicable values. The CLK_OUT pin can also + be disabled by this property. When omitted, the + PHY's default will be left as is. Note: ti,min-output-impedance and ti,max-output-impedance are mutually exclusive. When both properties are present ti,max-output-impedance diff --git a/Documentation/devicetree/bindings/net/wiznet,w5x00.txt b/Documentation/devicetree/bindings/net/wiznet,w5x00.txt new file mode 100644 index 000000000000..e9665798c4be --- /dev/null +++ b/Documentation/devicetree/bindings/net/wiznet,w5x00.txt @@ -0,0 +1,50 @@ +* Wiznet w5x00 + +This is a standalone 10/100 MBit Ethernet controller with SPI interface. + +For each device connected to a SPI bus, define a child node within +the SPI master node. + +Required properties: +- compatible: Should be one of the following strings: + "wiznet,w5100" + "wiznet,w5200" + "wiznet,w5500" +- reg: Specify the SPI chip select the chip is wired to. +- interrupts: Specify the interrupt index within the interrupt controller (referred + to above in interrupt-parent) and interrupt type. w5x00 natively + generates falling edge interrupts, however, additional board logic + might invert the signal. +- pinctrl-names: List of assigned state names, see pinctrl binding documentation. +- pinctrl-0: List of phandles to configure the GPIO pin used as interrupt line, + see also generic and your platform specific pinctrl binding + documentation. + +Optional properties: +- spi-max-frequency: Maximum frequency of the SPI bus when accessing the w5500. + According to the w5500 datasheet, the chip allows a maximum of 80 MHz, however, + board designs may need to limit this value. +- local-mac-address: See ethernet.txt in the same directory. + + +Example (for Raspberry Pi with pin control stuff for GPIO irq): + +&spi { + ethernet@0: w5500@0 { + compatible = "wiznet,w5500"; + reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <ð1_pins>; + interrupt-parent = <&gpio>; + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + spi-max-frequency = <30000000>; + }; +}; + +&gpio { + eth1_pins: eth1_pins { + brcm,pins = <25>; + brcm,function = <0>; /* in */ + brcm,pull = <0>; /* none */ + }; +}; diff --git a/Documentation/devicetree/bindings/net/xilinx_axienet.txt b/Documentation/devicetree/bindings/net/xilinx_axienet.txt index 38f9ec076743..7360617cdedb 100644 --- a/Documentation/devicetree/bindings/net/xilinx_axienet.txt +++ b/Documentation/devicetree/bindings/net/xilinx_axienet.txt @@ -17,8 +17,15 @@ For more details about mdio please refer phy.txt file in the same directory. Required properties: - compatible : Must be one of "xlnx,axi-ethernet-1.00.a", "xlnx,axi-ethernet-1.01.a", "xlnx,axi-ethernet-2.01.a" -- reg : Address and length of the IO space. -- interrupts : Should be a list of two interrupt, TX and RX. +- reg : Address and length of the IO space, as well as the address + and length of the AXI DMA controller IO space, unless + axistream-connected is specified, in which case the reg + attribute of the node referenced by it is used. +- interrupts : Should be a list of 2 or 3 interrupts: TX DMA, RX DMA, + and optionally Ethernet core. If axistream-connected is + specified, the TX/RX DMA interrupts should be on that node + instead, and only the Ethernet core interrupt is optionally + specified here. - phy-handle : Should point to the external phy device. See ethernet.txt file in the same directory. - xlnx,rxmem : Set to allocated memory buffer for Rx/Tx in the hardware @@ -31,15 +38,29 @@ Optional properties: 1 to enable partial TX checksum offload, 2 to enable full TX checksum offload - xlnx,rxcsum : Same values as xlnx,txcsum but for RX checksum offload +- clocks : AXI bus clock for the device. Refer to common clock bindings. + Used to calculate MDIO clock divisor. If not specified, it is + auto-detected from the CPU clock (but only on platforms where + this is possible). New device trees should specify this - the + auto detection is only for backward compatibility. +- axistream-connected: Reference to another node which contains the resources + for the AXI DMA controller used by this device. + If this is specified, the DMA-related resources from that + device (DMA registers and DMA TX/RX interrupts) rather + than this one will be used. + - mdio : Child node for MDIO bus. Must be defined if PHY access is + required through the core's MDIO interface (i.e. always, + unless the PHY is accessed through a different bus). Example: axi_ethernet_eth: ethernet@40c00000 { compatible = "xlnx,axi-ethernet-1.00.a"; device_type = "network"; interrupt-parent = <µblaze_0_axi_intc>; - interrupts = <2 0>; + interrupts = <2 0 1>; + clocks = <&axi_clk>; phy-mode = "mii"; - reg = <0x40c00000 0x40000>; + reg = <0x40c00000 0x40000 0x50c00000 0x40000>; xlnx,rxcsum = <0x2>; xlnx,rxmem = <0x800>; xlnx,txcsum = <0x2>; diff --git a/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt b/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt index 454c937076a2..d48f9eb3636e 100644 --- a/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt +++ b/Documentation/devicetree/bindings/ptp/ptp-qoriq.txt @@ -4,6 +4,8 @@ General Properties: - compatible Should be "fsl,etsec-ptp" for eTSEC Should be "fsl,fman-ptp-timer" for DPAA FMan + Should be "fsl,dpaa2-ptp" for DPAA2 + Should be "fsl,enetc-ptp" for ENETC - reg Offset and length of the register set for the device - interrupts There should be at least two interrupts. Some devices have as many as four PTP related interrupts. |