diff options
Diffstat (limited to 'Documentation/kernel-parameters.txt')
| -rw-r--r-- | Documentation/kernel-parameters.txt | 105 |
1 files changed, 85 insertions, 20 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 5d4427d17281..fce5b5e516cc 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -57,6 +57,7 @@ parameter is applicable: ISAPNP ISA PnP code is enabled. ISDN Appropriate ISDN support is enabled. JOY Appropriate joystick support is enabled. + KVM Kernel Virtual Machine support is enabled. LIBATA Libata driver is enabled LP Printer support is enabled. LOOP Loopback device support is enabled. @@ -84,7 +85,6 @@ parameter is applicable: PPT Parallel port support is enabled. PS2 Appropriate PS/2 support is enabled. RAM RAM disk support is enabled. - ROOTPLUG The example Root Plug LSM is enabled. S390 S390 architecture is enabled. SCSI Appropriate SCSI support is enabled. A lot of drivers has their options described inside of @@ -344,6 +344,15 @@ and is between 256 and 4096 characters. It is defined in the file Change the amount of debugging information output when initialising the APIC and IO-APIC components. + show_lapic= [APIC,X86] Advanced Programmable Interrupt Controller + Limit apic dumping. The parameter defines the maximal + number of local apics being dumped. Also it is possible + to set it to "all" by meaning -- no limit here. + Format: { 1 (default) | 2 | ... | all }. + The parameter valid if only apic=debug or + apic=verbose is specified. + Example: apic=debug show_lapic=all + apm= [APM] Advanced Power Management See header of arch/x86/kernel/apm_32.c. @@ -670,7 +679,8 @@ and is between 256 and 4096 characters. It is defined in the file earlyprintk= [X86,SH,BLACKFIN] earlyprintk=vga earlyprintk=serial[,ttySn[,baudrate]] - earlyprintk=dbgp + earlyprintk=ttySn[,baudrate] + earlyprintk=dbgp[debugController#] Append ",keep" to not disable it when the real console takes over. @@ -777,6 +787,13 @@ and is between 256 and 4096 characters. It is defined in the file by the set_ftrace_notrace file in the debugfs tracing directory. + ftrace_graph_filter=[function-list] + [FTRACE] Limit the top level callers functions traced + by the function graph tracer at boot up. + function-list is a comma separated list of functions + that can be changed at run time by the + set_graph_function file in the debugfs tracing directory. + gamecon.map[2|3]= [HW,JOY] Multisystem joystick and NES/SNES/PSX pad support via parallel port (up to 5 devices per port) @@ -932,7 +949,7 @@ and is between 256 and 4096 characters. It is defined in the file 1 -- enable informational integrity auditing messages. ima_hash= [IMA] - Formt: { "sha1" | "md5" } + Format: { "sha1" | "md5" } default: "sha1" ima_tcb [IMA] @@ -1098,6 +1115,44 @@ and is between 256 and 4096 characters. It is defined in the file kstack=N [X86] Print N words from the kernel stack in oops dumps. + kvm.ignore_msrs=[KVM] Ignore guest accesses to unhandled MSRs. + Default is 0 (don't ignore, but inject #GP) + + kvm.oos_shadow= [KVM] Disable out-of-sync shadow paging. + Default is 1 (enabled) + + kvm-amd.nested= [KVM,AMD] Allow nested virtualization in KVM/SVM. + Default is 0 (off) + + kvm-amd.npt= [KVM,AMD] Disable nested paging (virtualized MMU) + for all guests. + Default is 1 (enabled) if in 64bit or 32bit-PAE mode + + kvm-intel.bypass_guest_pf= + [KVM,Intel] Disables bypassing of guest page faults + on Intel chips. Default is 1 (enabled) + + kvm-intel.ept= [KVM,Intel] Disable extended page tables + (virtualized MMU) support on capable Intel chips. + Default is 1 (enabled) + + kvm-intel.emulate_invalid_guest_state= + [KVM,Intel] Enable emulation of invalid guest states + Default is 0 (disabled) + + kvm-intel.flexpriority= + [KVM,Intel] Disable FlexPriority feature (TPR shadow). + Default is 1 (enabled) + + kvm-intel.unrestricted_guest= + [KVM,Intel] Disable unrestricted guest feature + (virtualized real and unpaged mode) on capable + Intel chips. Default is 1 (enabled) + + kvm-intel.vpid= [KVM,Intel] Disable Virtual Processor Identification + feature (tagged TLBs) on capable Intel chips. + Default is 1 (enabled) + l2cr= [PPC] l3cr= [PPC] @@ -1247,6 +1302,10 @@ and is between 256 and 4096 characters. It is defined in the file (machvec) in a generic kernel. Example: machvec=hpzx1_swiotlb + machtype= [Loongson] Share the same kernel image file between different + yeeloong laptop. + Example: machtype=lemote-yeeloong-2f-7inch + max_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory greater than or equal to this physical address is ignored. @@ -1522,7 +1581,7 @@ and is between 256 and 4096 characters. It is defined in the file of returning the full 64-bit number. The default is to return 64-bit inode numbers. - nmi_debug= [KNL,AVR32] Specify one or more actions to take + nmi_debug= [KNL,AVR32,SH] Specify one or more actions to take when a NMI is triggered. Format: [state][,regs][,debounce][,die] @@ -1543,6 +1602,11 @@ and is between 256 and 4096 characters. It is defined in the file symbolic names: lapic and ioapic Example: nmi_watchdog=2 or nmi_watchdog=panic,lapic + netpoll.carrier_timeout= + [NET] Specifies amount of time (in seconds) that + netpoll should wait for a carrier. By default netpoll + waits 4 seconds. + no387 [BUGS=X86-32] Tells the kernel to use the 387 maths emulation library even if a 387 maths coprocessor is present. @@ -1927,11 +1991,12 @@ and is between 256 and 4096 characters. It is defined in the file Format: { 0 | 1 } See arch/parisc/kernel/pdc_chassis.c - percpu_alloc= [X86] Select which percpu first chunk allocator to use. - Allowed values are one of "lpage", "embed" and "4k". - See comments in arch/x86/kernel/setup_percpu.c for - details on each allocator. This parameter is primarily - for debugging and performance comparison. + percpu_alloc= Select which percpu first chunk allocator to use. + Currently supported values are "embed" and "page". + Archs may support subset or none of the selections. + See comments in mm/percpu.c for details on each + allocator. This parameter is primarily for debugging + and performance comparison. pf. [PARIDE] See Documentation/blockdev/paride.txt. @@ -1982,8 +2047,15 @@ and is between 256 and 4096 characters. It is defined in the file print-fatal-signals= [KNL] debug: print fatal signals - print-fatal-signals=1: print segfault info to - the kernel console. + + If enabled, warn about various signal handling + related application anomalies: too many signals, + too many POSIX.1 timers, fatal signals causing a + coredump - etc. + + If you hit the warning due to signal overflow, + you might want to try "ulimit -i unlimited". + default: off. printk.time= Show timing data prefixed to each printk message line @@ -2114,15 +2186,6 @@ and is between 256 and 4096 characters. It is defined in the file Useful for devices that are detected asynchronously (e.g. USB and MMC devices). - root_plug.vendor_id= - [ROOTPLUG] Override the default vendor ID - - root_plug.product_id= - [ROOTPLUG] Override the default product ID - - root_plug.debug= - [ROOTPLUG] Enable debugging output - rw [KNL] Mount root device read-write on boot S [KNL] Run init in single mode @@ -2132,6 +2195,8 @@ and is between 256 and 4096 characters. It is defined in the file sbni= [NET] Granch SBNI12 leased line adapter + sched_debug [KNL] Enables verbose scheduler debug messages. + sc1200wdt= [HW,WDT] SC1200 WDT (watchdog) driver Format: <io>[,<timeout>[,<isapnp>]] |