summaryrefslogtreecommitdiffstats
path: root/drivers/ata/pata_hpt3x2n.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/ata/pata_hpt3x2n.c')
-rw-r--r--drivers/ata/pata_hpt3x2n.c120
1 files changed, 56 insertions, 64 deletions
diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
index dd26bc73bd9a..01457b266f3d 100644
--- a/drivers/ata/pata_hpt3x2n.c
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -25,7 +25,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_hpt3x2n"
-#define DRV_VERSION "0.3.8"
+#define DRV_VERSION "0.3.10"
enum {
HPT_PCI_FAST = (1 << 31),
@@ -45,25 +45,24 @@ struct hpt_chip {
/* key for bus clock timings
* bit
- * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
- * DMA. cycles = value + 1
- * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW
- * DMA. cycles = value + 1
- * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file
+ * 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
+ * cycles = value + 1
+ * 4:8 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
+ * cycles = value + 1
+ * 9:12 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
* register access.
- * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file
+ * 13:17 cmd_low_time. Active time of DIOW_/DIOR_ during task file
* register access.
- * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer.
- * during task file register access.
- * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA
- * xfer.
- * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task
+ * 18:20 udma_cycle_time. Clock cycles for UDMA xfer.
+ * 21 CLK frequency for UDMA: 0=ATA clock, 1=dual ATA clock.
+ * 22:24 pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer.
+ * 25:27 cmd_pre_high_time. Time to initialize 1st PIO cycle for task file
* register access.
- * 28 UDMA enable
- * 29 DMA enable
- * 30 PIO_MST enable. if set, the chip is in bus master mode during
- * PIO.
- * 31 FIFO enable.
+ * 28 UDMA enable.
+ * 29 DMA enable.
+ * 30 PIO_MST enable. If set, the chip is in bus master mode during
+ * PIO xfer.
+ * 31 FIFO enable. Only for PIO.
*/
/* 66MHz DPLL clocks */
@@ -161,20 +160,12 @@ static int hpt3x2n_pre_reset(struct ata_link *link, unsigned long deadline)
return ata_sff_prereset(link, deadline);
}
-/**
- * hpt3x2n_set_piomode - PIO setup
- * @ap: ATA interface
- * @adev: device on the interface
- *
- * Perform PIO mode setup.
- */
-
-static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void hpt3x2n_set_mode(struct ata_port *ap, struct ata_device *adev,
+ u8 mode)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 addr1, addr2;
- u32 reg;
- u32 mode;
+ u32 reg, timing, mask;
u8 fast;
addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
@@ -185,11 +176,32 @@ static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
fast &= ~0x07;
pci_write_config_byte(pdev, addr2, fast);
+ /* Determine timing mask and find matching mode entry */
+ if (mode < XFER_MW_DMA_0)
+ mask = 0xcfc3ffff;
+ else if (mode < XFER_UDMA_0)
+ mask = 0x31c001ff;
+ else
+ mask = 0x303c0000;
+
+ timing = hpt3x2n_find_mode(ap, mode);
+
pci_read_config_dword(pdev, addr1, &reg);
- mode = hpt3x2n_find_mode(ap, adev->pio_mode);
- mode &= 0xCFC3FFFF; /* Leave DMA bits alone */
- reg &= ~0xCFC3FFFF; /* Strip timing bits */
- pci_write_config_dword(pdev, addr1, reg | mode);
+ reg = (reg & ~mask) | (timing & mask);
+ pci_write_config_dword(pdev, addr1, reg);
+}
+
+/**
+ * hpt3x2n_set_piomode - PIO setup
+ * @ap: ATA interface
+ * @adev: device on the interface
+ *
+ * Perform PIO mode setup.
+ */
+
+static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ hpt3x2n_set_mode(ap, adev, adev->pio_mode);
}
/**
@@ -197,32 +209,12 @@ static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
* @ap: ATA interface
* @adev: Device being configured
*
- * Set up the channel for MWDMA or UDMA modes. Much the same as with
- * PIO, load the mode number and then set MWDMA or UDMA flag.
+ * Set up the channel for MWDMA or UDMA modes.
*/
static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u32 addr1, addr2;
- u32 reg, mode, mask;
- u8 fast;
-
- addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
- addr2 = 0x51 + 4 * ap->port_no;
-
- /* Fast interrupt prediction disable, hold off interrupt disable */
- pci_read_config_byte(pdev, addr2, &fast);
- fast &= ~0x07;
- pci_write_config_byte(pdev, addr2, fast);
-
- mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000;
-
- pci_read_config_dword(pdev, addr1, &reg);
- mode = hpt3x2n_find_mode(ap, adev->dma_mode);
- mode &= mask;
- reg &= ~mask;
- pci_write_config_dword(pdev, addr1, reg | mode);
+ hpt3x2n_set_mode(ap, adev, adev->dma_mode);
}
/**
@@ -544,19 +536,19 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
pci_mhz);
/* Set our private data up. We only need a few flags so we use
it directly */
- if (pci_mhz > 60) {
+ if (pci_mhz > 60)
hpriv = (void *)(PCI66 | USE_DPLL);
- /*
- * On HPT371N, if ATA clock is 66 MHz we must set bit 2 in
- * the MISC. register to stretch the UltraDMA Tss timing.
- * NOTE: This register is only writeable via I/O space.
- */
- if (dev->device == PCI_DEVICE_ID_TTI_HPT371)
- outb(inb(iobase + 0x9c) | 0x04, iobase + 0x9c);
- }
+
+ /*
+ * On HPT371N, if ATA clock is 66 MHz we must set bit 2 in
+ * the MISC. register to stretch the UltraDMA Tss timing.
+ * NOTE: This register is only writeable via I/O space.
+ */
+ if (dev->device == PCI_DEVICE_ID_TTI_HPT371)
+ outb(inb(iobase + 0x9c) | 0x04, iobase + 0x9c);
/* Now kick off ATA set up */
- return ata_pci_sff_init_one(dev, ppi, &hpt3x2n_sht, hpriv);
+ return ata_pci_sff_init_one(dev, ppi, &hpt3x2n_sht, hpriv, 0);
}
static const struct pci_device_id hpt3x2n[] = {