summaryrefslogtreecommitdiffstats
path: root/drivers/cdrom/cdu31a.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/cdrom/cdu31a.c')
-rw-r--r--drivers/cdrom/cdu31a.c3251
1 files changed, 0 insertions, 3251 deletions
diff --git a/drivers/cdrom/cdu31a.c b/drivers/cdrom/cdu31a.c
deleted file mode 100644
index 2157c58755e0..000000000000
--- a/drivers/cdrom/cdu31a.c
+++ /dev/null
@@ -1,3251 +0,0 @@
-/*
-* Sony CDU-31A CDROM interface device driver.
-*
-* Corey Minyard (minyard@wf-rch.cirr.com)
-*
-* Colossians 3:17
-*
-* See Documentation/cdrom/cdu31a for additional details about this driver.
-*
-* The Sony interface device driver handles Sony interface CDROM
-* drives and provides a complete block-level interface as well as an
-* ioctl() interface compatible with the Sun (as specified in
-* include/linux/cdrom.h). With this interface, CDROMs can be
-* accessed and standard audio CDs can be played back normally.
-*
-* WARNING - All autoprobes have been removed from the driver.
-* You MUST configure the CDU31A via a LILO config
-* at boot time or in lilo.conf. I have the
-* following in my lilo.conf:
-*
-* append="cdu31a=0x1f88,0,PAS"
-*
-* The first number is the I/O base address of the
-* card. The second is the interrupt (0 means none).
- * The third should be "PAS" if on a Pro-Audio
- * spectrum, or nothing if on something else.
- *
- * This interface is (unfortunately) a polled interface. This is
- * because most Sony interfaces are set up with DMA and interrupts
- * disables. Some (like mine) do not even have the capability to
- * handle interrupts or DMA. For this reason you will see a lot of
- * the following:
- *
- * retry_count = jiffies+ SONY_JIFFIES_TIMEOUT;
- * while (time_before(jiffies, retry_count) && (! <some condition to wait for))
- * {
- * while (handle_sony_cd_attention())
- * ;
- *
- * sony_sleep();
- * }
- * if (the condition not met)
- * {
- * return an error;
- * }
- *
- * This ugly hack waits for something to happen, sleeping a little
- * between every try. it also handles attentions, which are
- * asynchronous events from the drive informing the driver that a disk
- * has been inserted, removed, etc.
- *
- * NEWS FLASH - The driver now supports interrupts but they are
- * turned off by default. Use of interrupts is highly encouraged, it
- * cuts CPU usage down to a reasonable level. I had DMA in for a while
- * but PC DMA is just too slow. Better to just insb() it.
- *
- * One thing about these drives: They talk in MSF (Minute Second Frame) format.
- * There are 75 frames a second, 60 seconds a minute, and up to 75 minutes on a
- * disk. The funny thing is that these are sent to the drive in BCD, but the
- * interface wants to see them in decimal. A lot of conversion goes on.
- *
- * DRIVER SPECIAL FEATURES
- * -----------------------
- *
- * This section describes features beyond the normal audio and CD-ROM
- * functions of the drive.
- *
- * XA compatibility
- *
- * The driver should support XA disks for both the CDU31A and CDU33A.
- * It does this transparently, the using program doesn't need to set it.
- *
- * Multi-Session
- *
- * A multi-session disk looks just like a normal disk to the user.
- * Just mount one normally, and all the data should be there.
- * A special thanks to Koen for help with this!
- *
- * Raw sector I/O
- *
- * Using the CDROMREADAUDIO it is possible to read raw audio and data
- * tracks. Both operations return 2352 bytes per sector. On the data
- * tracks, the first 12 bytes is not returned by the drive and the value
- * of that data is indeterminate.
- *
- *
- * Copyright (C) 1993 Corey Minyard
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * TODO:
- * CDs with form1 and form2 sectors cause problems
- * with current read-ahead strategy.
- *
- * Credits:
- * Heiko Eissfeldt <heiko@colossus.escape.de>
- * For finding abug in the return of the track numbers.
- * TOC processing redone for proper multisession support.
- *
- *
- * It probably a little late to be adding a history, but I guess I
- * will start.
- *
- * 10/24/95 - Added support for disabling the eject button when the
- * drive is open. Note that there is a small problem
- * still here, if the eject button is pushed while the
- * drive light is flashing, the drive will return a bad
- * status and be reset. It recovers, though.
- *
- * 03/07/97 - Fixed a problem with timers.
- *
- *
- * 18 Spetember 1997 -- Ported to Uniform CD-ROM driver by
- * Heiko Eissfeldt <heiko@colossus.escape.de> with additional
- * changes by Erik Andersen <andersee@debian.org>
- *
- * 24 January 1998 -- Removed the scd_disc_status() function, which was now
- * just dead code left over from the port.
- * Erik Andersen <andersee@debian.org>
- *
- * 16 July 1998 -- Drive donated to Erik Andersen by John Kodis
- * <kodis@jagunet.com>. Work begun on fixing driver to
- * work under 2.1.X. Added temporary extra printks
- * which seem to slow it down enough to work.
- *
- * 9 November 1999 -- Make kernel-parameter implementation work with 2.3.x
- * Removed init_module & cleanup_module in favor of
- * module_init & module_exit.
- * Torben Mathiasen <tmm@image.dk>
- *
- * 22 October 2004 -- Make the driver work in 2.6.X
- * Added workaround to fix hard lockups on eject
- * Fixed door locking problem after mounting empty drive
- * Set double-speed drives to double speed by default
- * Removed all readahead things - not needed anymore
- * Ondrej Zary <rainbow@rainbow-software.org>
-*/
-
-#define DEBUG 1
-
-#include <linux/major.h>
-#include <linux/module.h>
-#include <linux/errno.h>
-#include <linux/signal.h>
-#include <linux/sched.h>
-#include <linux/timer.h>
-#include <linux/fs.h>
-#include <linux/kernel.h>
-#include <linux/hdreg.h>
-#include <linux/genhd.h>
-#include <linux/ioport.h>
-#include <linux/string.h>
-#include <linux/slab.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/cdrom.h>
-
-#include <asm/system.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
-#include <asm/dma.h>
-
-#include "cdu31a.h"
-
-#define MAJOR_NR CDU31A_CDROM_MAJOR
-#include <linux/blkdev.h>
-
-#define CDU31A_MAX_CONSECUTIVE_ATTENTIONS 10
-
-#define PFX "CDU31A: "
-
-/*
-** Edit the following data to change interrupts, DMA channels, etc.
-** Default is polled and no DMA. DMA is not recommended for double-speed
-** drives.
-*/
-static struct {
- unsigned short base; /* I/O Base Address */
- short int_num; /* Interrupt Number (-1 means scan for it,
- 0 means don't use) */
-} cdu31a_addresses[] __initdata = {
- {0}
-};
-
-static int handle_sony_cd_attention(void);
-static int read_subcode(void);
-static void sony_get_toc(void);
-static int scd_spinup(void);
-/*static int scd_open(struct inode *inode, struct file *filp);*/
-static int scd_open(struct cdrom_device_info *, int);
-static void do_sony_cd_cmd(unsigned char cmd,
- unsigned char *params,
- unsigned int num_params,
- unsigned char *result_buffer,
- unsigned int *result_size);
-static void size_to_buf(unsigned int size, unsigned char *buf);
-
-/* Parameters for the read-ahead. */
-static unsigned int sony_next_block; /* Next 512 byte block offset */
-static unsigned int sony_blocks_left = 0; /* Number of 512 byte blocks left
- in the current read command. */
-
-
-/* The base I/O address of the Sony Interface. This is a variable (not a
- #define) so it can be easily changed via some future ioctl() */
-static unsigned int cdu31a_port = 0;
-module_param(cdu31a_port, uint, 0);
-
-/*
- * The following are I/O addresses of the various registers for the drive. The
- * comment for the base address also applies here.
- */
-static volatile unsigned short sony_cd_cmd_reg;
-static volatile unsigned short sony_cd_param_reg;
-static volatile unsigned short sony_cd_write_reg;
-static volatile unsigned short sony_cd_control_reg;
-static volatile unsigned short sony_cd_status_reg;
-static volatile unsigned short sony_cd_result_reg;
-static volatile unsigned short sony_cd_read_reg;
-static volatile unsigned short sony_cd_fifost_reg;
-
-static struct request_queue *cdu31a_queue;
-static DEFINE_SPINLOCK(cdu31a_lock); /* queue lock */
-
-static int sony_spun_up = 0; /* Has the drive been spun up? */
-
-static int sony_speed = 0; /* Last wanted speed */
-
-static int sony_xa_mode = 0; /* Is an XA disk in the drive
- and the drive a CDU31A? */
-
-static int sony_raw_data_mode = 1; /* 1 if data tracks, 0 if audio.
- For raw data reads. */
-
-static unsigned int sony_usage = 0; /* How many processes have the
- drive open. */
-
-static int sony_pas_init = 0; /* Initialize the Pro-Audio
- Spectrum card? */
-
-static struct s_sony_session_toc single_toc; /* Holds the
- table of
- contents. */
-
-static struct s_all_sessions_toc sony_toc; /* entries gathered from all
- sessions */
-
-static int sony_toc_read = 0; /* Has the TOC been read for
- the drive? */
-
-static struct s_sony_subcode last_sony_subcode; /* Points to the last
- subcode address read */
-
-static DECLARE_MUTEX(sony_sem); /* Semaphore for drive hardware access */
-
-static int is_double_speed = 0; /* does the drive support double speed ? */
-
-static int is_auto_eject = 1; /* Door has been locked? 1=No/0=Yes */
-
-/*
- * The audio status uses the values from read subchannel data as specified
- * in include/linux/cdrom.h.
- */
-static volatile int sony_audio_status = CDROM_AUDIO_NO_STATUS;
-
-/*
- * The following are a hack for pausing and resuming audio play. The drive
- * does not work as I would expect it, if you stop it then start it again,
- * the drive seeks back to the beginning and starts over. This holds the
- * position during a pause so a resume can restart it. It uses the
- * audio status variable above to tell if it is paused.
- */
-static unsigned volatile char cur_pos_msf[3] = { 0, 0, 0 };
-static unsigned volatile char final_pos_msf[3] = { 0, 0, 0 };
-
-/* What IRQ is the drive using? 0 if none. */
-static int cdu31a_irq = 0;
-module_param(cdu31a_irq, int, 0);
-
-/* The interrupt handler will wake this queue up when it gets an
- interrupts. */
-static DECLARE_WAIT_QUEUE_HEAD(cdu31a_irq_wait);
-static int irq_flag = 0;
-
-static int curr_control_reg = 0; /* Current value of the control register */
-
-/* A disk changed variable. When a disk change is detected, it will
- all be set to TRUE. As the upper layers ask for disk_changed status
- it will be cleared. */
-static char disk_changed;
-
-/* This was readahead_buffer once... Now it's used only for audio reads */
-static char audio_buffer[CD_FRAMESIZE_RAW];
-
-/* Used to time a short period to abort an operation after the
- drive has been idle for a while. This keeps the light on
- the drive from flashing for very long. */
-static struct timer_list cdu31a_abort_timer;
-
-/* Marks if the timeout has started an abort read. This is used
- on entry to the drive to tell the code to read out the status
- from the abort read. */
-static int abort_read_started = 0;
-
-/*
- * Uniform cdrom interface function
- * report back, if disc has changed from time of last request.
- */
-static int scd_media_changed(struct cdrom_device_info *cdi, int disc_nr)
-{
- int retval;
-
- retval = disk_changed;
- disk_changed = 0;
-
- return retval;
-}
-
-/*
- * Uniform cdrom interface function
- * report back, if drive is ready
- */
-static int scd_drive_status(struct cdrom_device_info *cdi, int slot_nr)
-{
- if (CDSL_CURRENT != slot_nr)
- /* we have no changer support */
- return -EINVAL;
- if (sony_spun_up)
- return CDS_DISC_OK;
- if (down_interruptible(&sony_sem))
- return -ERESTARTSYS;
- if (scd_spinup() == 0)
- sony_spun_up = 1;
- up(&sony_sem);
- return sony_spun_up ? CDS_DISC_OK : CDS_DRIVE_NOT_READY;
-}
-
-static inline void enable_interrupts(void)
-{
- curr_control_reg |= (SONY_ATTN_INT_EN_BIT
- | SONY_RES_RDY_INT_EN_BIT
- | SONY_DATA_RDY_INT_EN_BIT);
- outb(curr_control_reg, sony_cd_control_reg);
-}
-
-static inline void disable_interrupts(void)
-{
- curr_control_reg &= ~(SONY_ATTN_INT_EN_BIT
- | SONY_RES_RDY_INT_EN_BIT
- | SONY_DATA_RDY_INT_EN_BIT);
- outb(curr_control_reg, sony_cd_control_reg);
-}
-
-/*
- * Wait a little while (used for polling the drive). If in initialization,
- * setting a timeout doesn't work, so just loop for a while.
- */
-static inline void sony_sleep(void)
-{
- if (cdu31a_irq <= 0) {
- yield();
- } else { /* Interrupt driven */
- DEFINE_WAIT(w);
- int first = 1;
-
- while (1) {
- prepare_to_wait(&cdu31a_irq_wait, &w,
- TASK_INTERRUPTIBLE);
- if (first) {
- enable_interrupts();
- first = 0;
- }
-
- if (irq_flag != 0)
- break;
- if (!signal_pending(current)) {
- schedule();
- continue;
- } else
- disable_interrupts();
- break;
- }
- finish_wait(&cdu31a_irq_wait, &w);
- irq_flag = 0;
- }
-}
-
-
-/*
- * The following are convenience routine to read various status and set
- * various conditions in the drive.
- */
-static inline int is_attention(void)
-{
- return (inb(sony_cd_status_reg) & SONY_ATTN_BIT) != 0;
-}
-
-static inline int is_busy(void)
-{
- return (inb(sony_cd_status_reg) & SONY_BUSY_BIT) != 0;
-}
-
-static inline int is_data_ready(void)
-{
- return (inb(sony_cd_status_reg) & SONY_DATA_RDY_BIT) != 0;
-}
-
-static inline int is_data_requested(void)
-{
- return (inb(sony_cd_status_reg) & SONY_DATA_REQUEST_BIT) != 0;
-}
-
-static inline int is_result_ready(void)
-{
- return (inb(sony_cd_status_reg) & SONY_RES_RDY_BIT) != 0;
-}
-
-static inline int is_param_write_rdy(void)
-{
- return (inb(sony_cd_fifost_reg) & SONY_PARAM_WRITE_RDY_BIT) != 0;
-}
-
-static inline int is_result_reg_not_empty(void)
-{
- return (inb(sony_cd_fifost_reg) & SONY_RES_REG_NOT_EMP_BIT) != 0;
-}
-
-static inline void reset_drive(void)
-{
- curr_control_reg = 0;
- sony_toc_read = 0;
- outb(SONY_DRIVE_RESET_BIT, sony_cd_control_reg);
-}
-
-/*
- * Uniform cdrom interface function
- * reset drive and return when it is ready
- */
-static int scd_reset(struct cdrom_device_info *cdi)
-{
- unsigned long retry_count;
-
- if (down_interruptible(&sony_sem))
- return -ERESTARTSYS;
- reset_drive();
-
- retry_count = jiffies + SONY_RESET_TIMEOUT;
- while (time_before(jiffies, retry_count) && (!is_attention())) {
- sony_sleep();
- }
-
- up(&sony_sem);
- return 0;
-}
-
-static inline void clear_attention(void)
-{
- outb(curr_control_reg | SONY_ATTN_CLR_BIT, sony_cd_control_reg);
-}
-
-static inline void clear_result_ready(void)
-{
- outb(curr_control_reg | SONY_RES_RDY_CLR_BIT, sony_cd_control_reg);
-}
-
-static inline void clear_data_ready(void)
-{
- outb(curr_control_reg | SONY_DATA_RDY_CLR_BIT,
- sony_cd_control_reg);
-}
-
-static inline void clear_param_reg(void)
-{
- outb(curr_control_reg | SONY_PARAM_CLR_BIT, sony_cd_control_reg);
-}
-
-static inline unsigned char read_status_register(void)
-{
- return inb(sony_cd_status_reg);
-}
-
-static inline unsigned char read_result_register(void)
-{
- return inb(sony_cd_result_reg);
-}
-
-static inline unsigned char read_data_register(void)
-{
- return inb(sony_cd_read_reg);
-}
-
-static inline void write_param(unsigned char param)
-{
- outb(param, sony_cd_param_reg);
-}
-
-static inline void write_cmd(unsigned char cmd)
-{
- outb(curr_control_reg | SONY_RES_RDY_INT_EN_BIT,
- sony_cd_control_reg);
- outb(cmd, sony_cd_cmd_reg);
-}
-
-static irqreturn_t cdu31a_interrupt(int irq, void *dev_id)
-{
- unsigned char val;
-
- if (abort_read_started) {
- /* We might be waiting for an abort to finish. Don't
- disable interrupts yet, though, because we handle
- this one here. */
- /* Clear out the result registers. */
- while (is_result_reg_not_empty()) {
- val = read_result_register();
- }
- clear_data_ready();
- clear_result_ready();
-
- /* Clear out the data */
- while (is_data_requested()) {
- val = read_data_register();
- }
- abort_read_started = 0;
-
- /* If something was waiting, wake it up now. */
- if (waitqueue_active(&cdu31a_irq_wait)) {
- disable_interrupts();
- irq_flag = 1;
- wake_up_interruptible(&cdu31a_irq_wait);
- }
- } else if (waitqueue_active(&cdu31a_irq_wait)) {
- disable_interrupts();
- irq_flag = 1;
- wake_up_interruptible(&cdu31a_irq_wait);
- } else {
- disable_interrupts();
- printk(KERN_NOTICE PFX
- "Got an interrupt but nothing was waiting\n");
- }
- return IRQ_HANDLED;
-}
-
-/*
- * give more verbose error messages
- */
-static unsigned char *translate_error(unsigned char err_code)
-{
- static unsigned char errbuf[80];
-
- switch (err_code) {
- case 0x10: return "illegal command ";
- case 0x11: return "illegal parameter ";
-
- case 0x20: return "not loaded ";
- case 0x21: return "no disc ";
- case 0x22: return "not spinning ";
- case 0x23: return "spinning ";
- case 0x25: return "spindle servo ";
- case 0x26: return "focus servo ";
- case 0x29: return "eject mechanism ";
- case 0x2a: return "audio playing ";
- case 0x2c: return "emergency eject ";
-
- case 0x30: return "focus ";
- case 0x31: return "frame sync ";
- case 0x32: return "subcode address ";
- case 0x33: return "block sync ";
- case 0x34: return "header address ";
-
- case 0x40: return "illegal track read ";
- case 0x41: return "mode 0 read ";
- case 0x42: return "illegal mode read ";
- case 0x43: return "illegal block size read ";
- case 0x44: return "mode read ";
- case 0x45: return "form read ";
- case 0x46: return "leadout read ";
- case 0x47: return "buffer overrun ";
-
- case 0x53: return "unrecoverable CIRC ";
- case 0x57: return "unrecoverable LECC ";
-
- case 0x60: return "no TOC ";
- case 0x61: return "invalid subcode data ";
- case 0x63: return "focus on TOC read ";
- case 0x64: return "frame sync on TOC read ";
- case 0x65: return "TOC data ";
-
- case 0x70: return "hardware failure ";
- case 0x91: return "leadin ";
- case 0x92: return "leadout ";
- case 0x93: return "data track ";
- }
- sprintf(errbuf, "unknown 0x%02x ", err_code);
- return errbuf;
-}
-
-/*
- * Set the drive parameters so the drive will auto-spin-up when a
- * disk is inserted.
- */
-static void set_drive_params(int want_doublespeed)
-{
- unsigned char res_reg[12];
- unsigned int res_size;
- unsigned char params[3];
-
-
- params[0] = SONY_SD_AUTO_SPIN_DOWN_TIME;
- params[1] = 0x00; /* Never spin down the drive. */
- do_sony_cd_cmd(SONY_SET_DRIVE_PARAM_CMD,
- params, 2, res_reg, &res_size);
- if ((res_size < 2) || ((res_reg[0] & 0xf0) == 0x20)) {
- printk(KERN_NOTICE PFX
- "Unable to set spin-down time: 0x%2.2x\n", res_reg[1]);
- }
-
- params[0] = SONY_SD_MECH_CONTROL;
- params[1] = SONY_AUTO_SPIN_UP_BIT; /* Set auto spin up */
-
- if (is_auto_eject)
- params[1] |= SONY_AUTO_EJECT_BIT;
-
- if (is_double_speed && want_doublespeed) {
- params[1] |= SONY_DOUBLE_SPEED_BIT; /* Set the drive to double speed if
- possible */
- }
- do_sony_cd_cmd(SONY_SET_DRIVE_PARAM_CMD,
- params, 2, res_reg, &res_size);
- if ((res_size < 2) || ((res_reg[0] & 0xf0) == 0x20)) {
- printk(KERN_NOTICE PFX "Unable to set mechanical "
- "parameters: 0x%2.2x\n", res_reg[1]);
- }
-}
-
-/*
- * Uniform cdrom interface function
- * select reading speed for data access
- */
-static int scd_select_speed(struct cdrom_device_info *cdi, int speed)
-{
- if (speed == 0)
- sony_speed = 1;
- else
- sony_speed = speed - 1;
-
- if (down_interruptible(&sony_sem))
- return -ERESTARTSYS;
- set_drive_params(sony_speed);
- up(&sony_sem);
- return 0;
-}
-
-/*
- * Uniform cdrom interface function
- * lock or unlock eject button
- */
-static int scd_lock_door(struct cdrom_device_info *cdi, int lock)
-{
- if (lock == 0) {
- is_auto_eject = 1;
- } else {
- is_auto_eject = 0;
- }
- if (down_interruptible(&sony_sem))
- return -ERESTARTSYS;
- set_drive_params(sony_speed);
- up(&sony_sem);
- return 0;
-}
-
-/*
- * This code will reset the drive and attempt to restore sane parameters.
- */
-static void restart_on_error(void)
-{
- unsigned char res_reg[12];
- unsigned int res_size;
- unsigned long retry_count;
-
-
- printk(KERN_NOTICE PFX "Resetting drive on error\n");
- reset_drive();
- retry_count = jiffies + SONY_RESET_TIMEOUT;
- while (time_before(jiffies, retry_count) && (!is_attention())) {
- sony_sleep();
- }
- set_drive_params(sony_speed);
- do_sony_cd_cmd(SONY_SPIN_UP_CMD, NULL, 0, res_reg, &res_size);
- if ((res_size < 2) || ((res_reg[0] & 0xf0) == 0x20)) {
- printk(KERN_NOTICE PFX "Unable to spin up drive: 0x%2.2x\n",
- res_reg[1]);
- }
-
- msleep(2000);
-
- sony_get_toc();
-}
-
-/*
- * This routine writes data to the parameter register. Since this should
- * happen fairly fast, it is polled with no OS waits between.
- */
-static int write_params(unsigned char *params, int num_params)
-{
- unsigned int retry_count;
-
-
- retry_count = SONY_READY_RETRIES;
- while ((retry_count > 0) && (!is_param_write_rdy())) {
- retry_count--;
- }
- if (!is_param_write_rdy()) {
- return -EIO;
- }
-
- while (num_params > 0) {
- write_param(*params);
- params++;
- num_params--;
- }
-
- return 0;
-}
-
-
-/*
- * The following reads data from the command result register. It is a
- * fairly complex routine, all status info flows back through this
- * interface. The algorithm is stolen directly from the flowcharts in
- * the drive manual.
- */
-static void
-get_result(unsigned char *result_buffer, unsigned int *result_size)
-{
- unsigned char a, b;
- int i;
- unsigned long retry_count;
-
-
- while (handle_sony_cd_attention());
- /* Wait for the result data to be ready */
- retry_count = jiffies + SONY_JIFFIES_TIMEOUT;
- while (time_before(jiffies, retry_count)
- && (is_busy() || (!(is_result_ready())))) {
- sony_sleep();
-
- while (handle_sony_cd_attention());
- }
- if (is_busy() || (!(is_result_ready()))) {
- pr_debug(PFX "timeout out %d\n", __LINE__);
- result_buffer[0] = 0x20;
- result_buffer[1] = SONY_TIMEOUT_OP_ERR;
- *result_size = 2;
- return;
- }
-
- /*
- * Get the first two bytes. This determines what else needs
- * to be done.
- */
- clear_result_ready();
- a = read_result_register();
- *result_buffer = a;
- result_buffer++;
-
- /* Check for block error status result. */
- if ((a & 0xf0) == 0x50) {
- *result_size = 1;
- return;
- }
-
- b = read_result_register();
- *result_buffer = b;
- result_buffer++;
- *result_size = 2;
-
- /*
- * 0x20 means an error occurred. Byte 2 will have the error code.
- * Otherwise, the command succeeded, byte 2 will have the count of
- * how many more status bytes are coming.
- *
- * The result register can be read 10 bytes at a time, a wait for
- * result ready to be asserted must be done between every 10 bytes.
- */
- if ((a & 0xf0) != 0x20) {
- if (b > 8) {
- for (i = 0; i < 8; i++) {
- *result_buffer = read_result_register();
- result_buffer++;
- (*result_size)++;
- }
- b = b - 8;
-
- while (b > 10) {
- retry_count = SONY_READY_RETRIES;
- while ((retry_count > 0)
- && (!is_result_ready())) {
- retry_count--;
- }
- if (!is_result_ready()) {
- pr_debug(PFX "timeout out %d\n",
- __LINE__);
- result_buffer[0] = 0x20;
- result_buffer[1] =
- SONY_TIMEOUT_OP_ERR;
- *result_size = 2;
- return;
- }
-
- clear_result_ready();
-
- for (i = 0; i < 10; i++) {
- *result_buffer =
- read_result_register();
- result_buffer++;
- (*result_size)++;
- }
- b = b - 10;
- }
-
- if (b > 0) {
- retry_count = SONY_READY_RETRIES;
- while ((retry_count > 0)
- && (!is_result_ready())) {
- retry_count--;
- }
- if (!is_result_ready()) {
- pr_debug(PFX "timeout out %d\n",
- __LINE__);
- result_buffer[0] = 0x20;
- result_buffer[1] =
- SONY_TIMEOUT_OP_ERR;
- *result_size = 2;
- return;
- }
- }
- }
-
- while (b > 0) {
- *result_buffer = read_result_register();
- result_buffer++;
- (*result_size)++;
- b--;
- }
- }
-}
-
-/*
- * Do a command that does not involve data transfer. This routine must
- * be re-entrant from the same task to support being called from the
- * data operation code when an error occurs.
- */
-static void
-do_sony_cd_cmd(unsigned char cmd,
- unsigned char *params,
- unsigned int num_params,
- unsigned char *result_buffer, unsigned int *result_size)
-{
- unsigned long retry_count;
- int num_retries = 0;
-
-retry_cd_operation:
-
- while (handle_sony_cd_attention());
-
- retry_count = jiffies + SONY_JIFFIES_TIMEOUT;
- while (time_before(jiffies, retry_count) && (is_busy())) {
- sony_sleep();
-
- while (handle_sony_cd_attention());
- }
- if (is_busy()) {
- pr_debug(PFX "timeout out %d\n", __LINE__);
- result_buffer[0] = 0x20;
- result_buffer[1] = SONY_TIMEOUT_OP_ERR;
- *result_size = 2;
- } else {
- clear_result_ready();
- clear_param_reg();
-
- write_params(params, num_params);
- write_cmd(cmd);
-
- get_result(result_buffer, result_size);
- }
-
- if (((result_buffer[0] & 0xf0) == 0x20)
- && (num_retries < MAX_CDU31A_RETRIES)) {
- num_retries++;
- msleep(100);
- goto retry_cd_operation;
- }
-}
-
-
-/*
- * Handle an attention from the drive. This will return 1 if it found one
- * or 0 if not (if one is found, the caller might want to call again).
- *
- * This routine counts the number of consecutive times it is called
- * (since this is always called from a while loop until it returns
- * a 0), and returns a 0 if it happens too many times. This will help
- * prevent a lockup.
- */
-static int handle_sony_cd_attention(void)
-{
- unsigned char atten_code;
- static int num_consecutive_attentions = 0;
- volatile int val;
-
-
-#if 0
- pr_debug(PFX "Entering %s\n", __FUNCTION__);
-#endif
- if (is_attention()) {
- if (num_consecutive_attentions >
- CDU31A_MAX_CONSECUTIVE_ATTENTIONS) {
- printk(KERN_NOTICE PFX "Too many consecutive "
- "attentions: %d\n", num_consecutive_attentions);
- num_consecutive_attentions = 0;
- pr_debug(PFX "Leaving %s at %d\n", __FUNCTION__,
- __LINE__);
- return 0;
- }
-
- clear_attention();
- atten_code = read_result_register();
-
- switch (atten_code) {
- /* Someone changed the CD. Mark it as changed */
- case SONY_MECH_LOADED_ATTN:
- disk_changed = 1;
- sony_toc_read = 0;
- sony_audio_status = CDROM_AUDIO_NO_STATUS;
- sony_blocks_left = 0;
- break;
-
- case SONY_SPIN_DOWN_COMPLETE_ATTN:
- /* Mark the disk as spun down. */
- sony_spun_up = 0;
- break;
-
- case SONY_AUDIO_PLAY_DONE_ATTN:
- sony_audio_status = CDROM_AUDIO_COMPLETED;
- read_subcode();
- break;
-
- case SONY_EJECT_PUSHED_ATTN:
- if (is_auto_eject) {
- sony_audio_status = CDROM_AUDIO_INVALID;
- }
- break;
-
- case SONY_LEAD_IN_ERR_ATTN:
- case SONY_LEAD_OUT_ERR_ATTN:
- case SONY_DATA_TRACK_ERR_ATTN:
- case SONY_AUDIO_PLAYBACK_ERR_ATTN:
- sony_audio_status = CDROM_AUDIO_ERROR;
- break;
- }
-
- num_consecutive_attentions++;
- pr_debug(PFX "Leaving %s at %d\n", __FUNCTION__, __LINE__);
- return 1;
- } else if (abort_read_started) {
- while (is_result_reg_not_empty()) {
- val = read_result_register();
- }
- clear_data_ready();
- clear_result_ready();
- /* Clear out the data */
- while (is_data_requested()) {
- val = read_data_register();
- }
- abort_read_started = 0;
- pr_debug(PFX "Leaving %s at %d\n", __FUNCTION__, __LINE__);
- return 1;
- }
-
- num_consecutive_attentions = 0;
-#if 0
- pr_debug(PFX "Leaving %s at %d\n", __FUNCTION__, __LINE__);
-#endif
- return 0;
-}
-
-
-/* Convert from an integer 0-99 to BCD */
-static inline unsigned int int_to_bcd(unsigned int val)
-{
- int retval;
-
-
- retval = (val / 10) << 4;
- retval = retval | val % 10;
- return retval;
-}
-
-
-/* Convert from BCD to an integer from 0-99 */
-static unsigned int bcd_to_int(unsigned int bcd)
-{
- return (((bcd >> 4) & 0x0f) * 10) + (bcd & 0x0f);
-}
-
-
-/*
- * Convert a logical sector value (like the OS would want to use for
- * a block device) to an MSF format.
- */
-static void log_to_msf(unsigned int log, unsigned char *msf)
-{
- log = log + LOG_START_OFFSET;
- msf[0] = int_to_bcd(log / 4500);
- log = log % 4500;
- msf[1] = int_to_bcd(log / 75);
- msf[2] = int_to_bcd(log % 75);
-}
-
-
-/*
- * Convert an MSF format to a logical sector.
- */
-static unsigned int msf_to_log(unsigned char *msf)
-{
- unsigned int log;
-
-
- log = msf[2];
- log += msf[1] * 75;
- log += msf[0] * 4500;
- log = log - LOG_START_OFFSET;
-
- return log;
-}
-
-
-/*
- * Take in integer size value and put it into a buffer like
- * the drive would want to see a number-of-sector value.
- */
-static void size_to_buf(unsigned int size, unsigned char *buf)
-{
- buf[0] = size / 65536;
- size = size % 65536;
- buf[1] = size / 256;
- buf[2] = size % 256;
-}
-
-/* Starts a read operation. Returns 0 on success and 1 on failure.
- The read operation used here allows multiple sequential sectors
- to be read and status returned for each sector. The driver will
- read the output one at a time as the requests come and abort the
- operation if the requested sector is not the next one from the
- drive. */
-static int
-start_request(unsigned int sector, unsigned int nsect)
-{
- unsigned char params[6];
- unsigned long retry_count;
-
-
- pr_debug(PFX "Entering %s\n", __FUNCTION__);
- log_to_msf(sector, params);
- size_to_buf(nsect, &params[3]);
-
- /*
- * Clear any outstanding attentions and wait for the drive to
- * complete any pending operations.
- */
- while (handle_sony_cd_attention());
-
- retry_count = jiffies + SONY_JIFFIES_TIMEOUT;
- while (time_before(jiffies, retry_count) && (is_busy())) {
- sony_sleep();
-
- while (handle_sony_cd_attention());
- }
-
- if (is_busy()) {
- printk(KERN_NOTICE PFX "Timeout while waiting "
- "to issue command\n");
- pr_debug(PFX "Leaving %s at %d\n", __FUNCTION__, __LINE__);
- return 1;
- } else {
- /* Issue the command */
- clear_result_ready();
- clear_param_reg();
-
- write_params(params, 6);
- write_cmd(SONY_READ_BLKERR_STAT_CMD);
-
- sony_blocks_left = nsect * 4;
- sony_next_block = sector * 4;
- pr_debug(PFX "Leaving %s at %d\n", __FUNCTION__, __LINE__);
- return 0;
- }
- pr_debug(PFX "Leaving %s at %d\n", __FUNCTION__, __LINE__);
-}
-
-/* Abort a pending read operation. Clear all the drive status variables. */
-static void abort_read(void)
-{
- unsigned char result_reg[2];
- int result_size;
- volatile int val;
-
-
- do_sony_cd_cmd(SONY_ABORT_CMD, NULL, 0, result_reg, &result_size);
- if ((result_reg[0] & 0xf0) == 0x20) {
- printk(KERN_ERR PFX "Aborting read, %s error\n",
- translate_error(result_reg[1]));
- }
-
- while (is_result_reg_not_empty()) {
- val = read_result_register();
- }
- clear_data_ready();
- clear_result_ready();
- /* Clear out the data */
- while (is_data_requested()) {
- val = read_data_register();
- }
-
- sony_blocks_left = 0;
-}
-
-/* Called when the timer times out. This will abort the
- pending read operation. */
-static void handle_abort_timeout(unsigned long data)
-{
- pr_debug(PFX "Entering %s\n", __FUNCTION__);
- /* If it is in use, ignore it. */
- if (down_trylock(&sony_sem) == 0) {
- /* We can't use abort_read(), because it will sleep
- or schedule in the timer interrupt. Just start
- the operation, finish it on the next access to
- the drive. */
- clear_result_ready();
- clear_param_reg();
- write_cmd(SONY_ABORT_CMD);
-
- sony_blocks_left = 0;
- abort_read_started = 1;
- up(&sony_sem);
- }
- pr_debug(PFX "Leaving %s\n", __FUNCTION__);
-}
-
-/* Actually get one sector of data from the drive. */
-static void
-input_data_sector(char *buffer)
-{
- pr_debug(PFX "Entering %s\n", __FUNCTION__);
-
- /* If an XA disk on a CDU31A, skip the first 12 bytes of data from
- the disk. The real data is after that. We can use audio_buffer. */
- if (sony_xa_mode)
- insb(sony_cd_read_reg, audio_buffer, CD_XA_HEAD);
-
- clear_data_ready();
-
- insb(sony_cd_read_reg, buffer, 2048);
-
- /* If an XA disk, we have to clear out the rest of the unused
- error correction data. We can use audio_buffer for that. */
- if (sony_xa_mode)
- insb(sony_cd_read_reg, audio_buffer, CD_XA_TAIL);
-
- pr_debug(PFX "Leaving %s\n", __FUNCTION__);
-}
-
-/* read data from the drive. Note the nsect must be <= 4. */
-static void
-read_data_block(char *buffer,
- unsigned int block,
- unsigned int nblocks,
- unsigned char res_reg[], int *res_size)
-{
- unsigned long retry_count;
-
- pr_debug(PFX "Entering %s\n", __FUNCTION__);
-
- res_reg[0] = 0;
- res_reg[1] = 0;
- *res_size = 0;
-
- /* Wait for the drive to tell us we have something */
- retry_count = jiffies + SONY_JIFFIES_TIMEOUT;
- while (time_before(jiffies, retry_count) && !(is_data_ready())) {
- while (handle_sony_cd_attention());
-
- sony_sleep();
- }
- if (!(is_data_ready())) {
- if (is_result_ready()) {
- get_result(res_reg, res_size);
- if ((res_reg[0] & 0xf0) != 0x20) {
- printk(KERN_NOTICE PFX "Got result that should"
- " have been error: %d\n", res_reg[0]);
- res_reg[0] = 0x20;
- res_reg[1] = SONY_BAD_DATA_ERR;
- *res_size = 2;
- }
- abort_read();
- } else {
- pr_debug(PFX "timeout out %d\n", __LINE__);
- res_reg[0] = 0x20;
- res_reg[1] = SONY_TIMEOUT_OP_ERR;
- *res_size = 2;
- abort_read();
- }
- } else {
- input_data_sector(buffer);
- sony_blocks_left -= nblocks;
- sony_next_block += nblocks;
-
- /* Wait for the status from the drive. */
- retry_count = jiffies + SONY_JIFFIES_TIMEOUT;
- while (time_before(jiffies, retry_count)
- && !(is_result_ready())) {
- while (handle_sony_cd_attention());
-
- sony_sleep();
- }
-
- if (!is_result_ready()) {
- pr_debug(PFX "timeout out %d\n", __LINE__);
- res_reg[0] = 0x20;
- res_reg[1] = SONY_TIMEOUT_OP_ERR;
- *res_size = 2;
- abort_read();
- } else {
- get_result(res_reg, res_size);
-
- /* If we got a buffer status, handle that. */
- if ((res_reg[0] & 0xf0) == 0x50) {
-
- if ((res_reg[0] ==
- SONY_NO_CIRC_ERR_BLK_STAT)
- || (res_reg[0] ==
- SONY_NO_LECC_ERR_BLK_STAT)
- || (res_reg[0] ==
- SONY_RECOV_LECC_ERR_BLK_STAT)) {
- /* nothing here */
- } else {
- printk(KERN_ERR PFX "Data block "
- "error: 0x%x\n", res_reg[0]);
- res_reg[0] = 0x20;
- res_reg[1] = SONY_BAD_DATA_ERR;
- *res_size = 2;
- }
-
- /* Final transfer is done for read command, get final result. */
- if (sony_blocks_left == 0) {
- get_result(res_reg, res_size);
- }
- } else if ((res_reg[0] & 0xf0) != 0x20) {
- /* The drive gave me bad status, I don't know what to do.
- Reset the driver and return an error. */
- printk(KERN_ERR PFX "Invalid block "
- "status: 0x%x\n", res_reg[0]);
- restart_on_error();
- res_reg[0] = 0x20;
- res_reg[1] = SONY_BAD_DATA_ERR;
- *res_size = 2;
- }
- }
- }
- pr_debug(PFX "Leaving %s at %d\n", __FUNCTION__, __LINE__);
-}
-
-
-/*
- * The OS calls this to perform a read or write operation to the drive.
- * Write obviously fail. Reads to a read ahead of sony_buffer_size
- * bytes to help speed operations. This especially helps since the OS
- * uses 1024 byte blocks and the drive uses 2048 byte blocks. Since most
- * data access on a CD is done sequentially, this saves a lot of operations.
- */
-static void do_cdu31a_request(request_queue_t * q)
-{
- struct request *req;
- int block, nblock, num_retries;
- unsigned char res_reg[12];
- unsigned int res_size;
-
- pr_debug(PFX "Entering %s\n", __FUNCTION__);
-
- spin_unlock_irq(q->queue_lock);
- if (down_interruptible(&sony_sem)) {
- spin_lock_irq(q->queue_lock);
- return;
- }
-
- /* Get drive status before doing anything. */
- while (handle_sony_cd_attention());
-
- /* Make sure we have a valid TOC. */
- sony_get_toc();
-
-
- /* Make sure the timer is cancelled. */
- del_timer(&cdu31a_abort_timer);
-
- while (1) {
- /*
- * The beginning here is stolen from the hard disk driver. I hope
- * it's right.
- */
- req = elv_next_request(q);
- if (!req)
- goto end_do_cdu31a_request;
-
- if (!sony_spun_up)
- scd_spinup();
-
- block = req->sector;
- nblock = req->nr_sectors;
- pr_debug(PFX "request at block %d, length %d blocks\n",
- block, nblock);
- if (!sony_toc_read) {
- printk(KERN_NOTICE PFX "TOC not read\n");
- end_request(req, 0);
- continue;
- }
-
- /* WTF??? */
- if (!blk_fs_request(req)) {
- end_request(req, 0);
- continue;
- }
- if (rq_data_dir(req) == WRITE) {
- end_request(req, 0);
- continue;
- }
-
- /*
- * If the block address is invalid or the request goes beyond the end of
- * the media, return an error.
- */
- if (((block + nblock) / 4) >= sony_toc.lead_out_start_lba) {
- printk(KERN_NOTICE PFX "Request past end of media\n");
- end_request(req, 0);
- continue;
- }
-
- if (nblock > 4)
- nblock = 4;
- num_retries = 0;
-
- try_read_again:
- while (handle_sony_cd_attention());
-
- if (!sony_toc_read) {
- printk(KERN_NOTICE PFX "TOC not read\n");
- end_request(req, 0);
- continue;
- }
-
- /* If no data is left to be read from the drive, start the
- next request. */
- if (sony_blocks_left == 0) {
- if (start_request(block / 4, nblock / 4)) {
- end_request(req, 0);
- continue;
- }
- }
- /* If the requested block is not the next one waiting in
- the driver, abort the current operation and start a
- new one. */
- else if (block != sony_next_block) {
- pr_debug(PFX "Read for block %d, expected %d\n",
- block, sony_next_block);
- abort_read();
- if (!sony_toc_read) {
- printk(KERN_NOTICE PFX "TOC not read\n");
- end_request(req, 0);
- continue;
- }
- if (start_request(block / 4, nblock / 4)) {
- printk(KERN_NOTICE PFX "start request failed\n");
- end_request(req, 0);
- continue;
- }
- }
-
- read_data_block(req->buffer, block, nblock, res_reg, &res_size);
-
- if (res_reg[0] != 0x20) {
- if (!end_that_request_first(req, 1, nblock)) {
- spin_lock_irq(q->queue_lock);
- blkdev_dequeue_request(req);
- end_that_request_last(req, 1);
- spin_unlock_irq(q->queue_lock);
- }
- continue;
- }
-
- if (num_retries > MAX_CDU31A_RETRIES) {
- end_request(req, 0);
- continue;
- }
-
- num_retries++;
- if (res_reg[1] == SONY_NOT_SPIN_ERR) {
- do_sony_cd_cmd(SONY_SPIN_UP_CMD, NULL, 0, res_reg,
- &res_size);
- } else {
- printk(KERN_NOTICE PFX "%s error for block %d, nblock %d\n",
- translate_error(res_reg[1]), block, nblock);
- }
- goto try_read_again;
- }
- end_do_cdu31a_request:
-#if 0
- /* After finished, cancel any pending operations. */
- abort_read();
-#else
- /* Start a timer to time out after a while to disable
- the read. */
- cdu31a_abort_timer.expires = jiffies + 2 * HZ; /* Wait 2 seconds */
- add_timer(&cdu31a_abort_timer);
-#endif
-
- up(&sony_sem);
- spin_lock_irq(q->queue_lock);
- pr_debug(PFX "Leaving %s at %d\n", __FUNCTION__, __LINE__);
-}
-
-
-/*
- * Read the table of contents from the drive and set up TOC if
- * successful.
- */
-static void sony_get_toc(void)
-{
- unsigned char res_reg[2];
- unsigned int res_size;
- unsigned char parms[1];
- int session;
- int num_spin_ups;
- int totaltracks = 0;
- int mint = 99;
- int maxt = 0;
-
- pr_debug(PFX "Entering %s\n", __FUNCTION__);
-
- num_spin_ups = 0;
- if (!sony_toc_read) {
- respinup_on_gettoc:
- /* Ignore the result, since it might error if spinning already. */
- do_sony_cd_cmd(SONY_SPIN_UP_CMD, NULL, 0, res_reg,
- &res_size);
-
- do_sony_cd_cmd(SONY_READ_TOC_CMD, NULL, 0, res_reg,
- &res_size);
-
- /* The drive sometimes returns error 0. I don't know why, but ignore
- it. It seems to mean the drive has already done the operation. */
- if ((res_size < 2)
- || ((res_reg[0] != 0) && (res_reg[1] != 0))) {
- /* If the drive is already playing, it's ok. */
- if ((res_reg[1] == SONY_AUDIO_PLAYING_ERR)
- || (res_reg[1] == 0)) {
- goto gettoc_drive_spinning;
- }
-
- /* If the drive says it is not spun up (even though we just did it!)
- then retry the operation at least a few times. */
- if ((res_reg[1] == SONY_NOT_SPIN_ERR)
- && (num_spin_ups < MAX_CDU31A_RETRIES)) {
- num_spin_ups++;
- goto respinup_on_gettoc;
- }
-
- printk("cdu31a: Error reading TOC: %x %s\n",
- res_reg[0], translate_error(res_reg[1]));
- return;
- }
-
- gettoc_drive_spinning:
-
- /* The idea here is we keep asking for sessions until the command
- fails. Then we know what the last valid session on the disk is.
- No need to check session 0, since session 0 is the same as session
- 1; the command returns different information if you give it 0.
- */
-#if DEBUG
- memset(&sony_toc, 0x0e, sizeof(sony_toc));
- memset(&single_toc, 0x0f, sizeof(single_toc));
-#endif
- session = 1;
- while (1) {
-/* This seems to slow things down enough to make it work. This
- * appears to be a problem in do_sony_cd_cmd. This printk seems
- * to address the symptoms... -Erik */
- pr_debug(PFX "Trying session %d\n", session);
- parms[0] = session;
- do_sony_cd_cmd(SONY_READ_TOC_SPEC_CMD,
- parms, 1, res_reg, &res_size);
-
- pr_debug(PFX "%2.2x %2.2x\n", res_reg[0], res_reg[1]);
-
- if ((res_size < 2)
- || ((res_reg[0] & 0xf0) == 0x20)) {
- /* An error reading the TOC, this must be past the last session. */
- if (session == 1)
- printk
- ("Yikes! Couldn't read any sessions!");
- break;
- }
- pr_debug(PFX "Reading session %d\n", session);
-
- parms[0] = session;
- do_sony_cd_cmd(SONY_REQ_TOC_DATA_SPEC_CMD,
- parms,
- 1,
- (unsigned char *) &single_toc,
- &res_size);
- if ((res_size < 2)
- || ((single_toc.exec_status[0] & 0xf0) ==
- 0x20)) {
- printk(KERN_ERR PFX "Error reading "
- "session %d: %x %s\n",
- session, single_toc.exec_status[0],
- translate_error(single_toc.
- exec_status[1]));
- /* An error reading the TOC. Return without sony_toc_read
- set. */
- return;
- }
- pr_debug(PFX "add0 %01x, con0 %01x, poi0 %02x, "
- "1st trk %d, dsktyp %x, dum0 %x\n",
- single_toc.address0, single_toc.control0,
- single_toc.point0,
- bcd_to_int(single_toc.first_track_num),
- single_toc.disk_type, single_toc.dummy0);
- pr_debug(PFX "add1 %01x, con1 %01x, poi1 %02x, "
- "lst trk %d, dummy1 %x, dum2 %x\n",
- single_toc.address1, single_toc.control1,
- single_toc.point1,
- bcd_to_int(single_toc.last_track_num),
- single_toc.dummy1, single_toc.dummy2);
- pr_debug(PFX "add2 %01x, con2 %01x, poi2 %02x "
- "leadout start min %d, sec %d, frame %d\n",
- single_toc.address2, single_toc.control2,
- single_toc.point2,
- bcd_to_int(single_toc.lead_out_start_msf[0]),
- bcd_to_int(single_toc.lead_out_start_msf[1]),
- bcd_to_int(single_toc.lead_out_start_msf[2]));
- if (res_size > 18 && single_toc.pointb0 > 0xaf)
- pr_debug(PFX "addb0 %01x, conb0 %01x, poib0 %02x, nextsession min %d, sec %d, frame %d\n"
- "#mode5_ptrs %02d, max_start_outer_leadout_msf min %d, sec %d, frame %d\n",
- single_toc.addressb0,
- single_toc.controlb0,
- single_toc.pointb0,
- bcd_to_int(single_toc.
- next_poss_prog_area_msf
- [0]),
- bcd_to_int(single_toc.
- next_poss_prog_area_msf
- [1]),
- bcd_to_int(single_toc.
- next_poss_prog_area_msf
- [2]),
- single_toc.num_mode_5_pointers,
- bcd_to_int(single_toc.
- max_start_outer_leadout_msf
- [0]),
- bcd_to_int(single_toc.
- max_start_outer_leadout_msf
- [1]),
- bcd_to_int(single_toc.
- max_start_outer_leadout_msf
- [2]));
- if (res_size > 27 && single_toc.pointb1 > 0xaf)
- pr_debug(PFX "addb1 %01x, conb1 %01x, poib1 %02x, %x %x %x %x #skipint_ptrs %d, #skiptrkassign %d %x\n",
- single_toc.addressb1,
- single_toc.controlb1,
- single_toc.pointb1,
- single_toc.dummyb0_1[0],
- single_toc.dummyb0_1[1],
- single_toc.dummyb0_1[2],
- single_toc.dummyb0_1[3],
- single_toc.num_skip_interval_pointers,
- single_toc.num_skip_track_assignments,
- single_toc.dummyb0_2);
- if (res_size > 36 && single_toc.pointb2 > 0xaf)
- pr_debug(PFX "addb2 %01x, conb2 %01x, poib2 %02x, %02x %02x %02x %02x %02x %02x %02x\n",
- single_toc.addressb2,
- single_toc.controlb2,
- single_toc.pointb2,
- single_toc.tracksb2[0],
- single_toc.tracksb2[1],
- single_toc.tracksb2[2],
- single_toc.tracksb2[3],
- single_toc.tracksb2[4],
- single_toc.tracksb2[5],
- single_toc.tracksb2[6]);
- if (res_size > 45 && single_toc.pointb3 > 0xaf)
- pr_debug(PFX "addb3 %01x, conb3 %01x, poib3 %02x, %02x %02x %02x %02x %02x %02x %02x\n",
- single_toc.addressb3,
- single_toc.controlb3,
- single_toc.pointb3,
- single_toc.tracksb3[0],
- single_toc.tracksb3[1],
- single_toc.tracksb3[2],
- single_toc.tracksb3[3],
- single_toc.tracksb3[4],
- single_toc.tracksb3[5],
- single_toc.tracksb3[6]);
- if (res_size > 54 && single_toc.pointb4 > 0xaf)
- pr_debug(PFX "addb4 %01x, conb4 %01x, poib4 %02x, %02x %02x %02x %02x %02x %02x %02x\n",
- single_toc.addressb4,
- single_toc.controlb4,
- single_toc.pointb4,
- single_toc.tracksb4[0],
- single_toc.tracksb4[1],
- single_toc.tracksb4[2],
- single_toc.tracksb4[3],
- single_toc.tracksb4[4],
- single_toc.tracksb4[5],
- single_toc.tracksb4[6]);
- if (res_size > 63 && single_toc.pointc0 > 0xaf)
- pr_debug(PFX "addc0 %01x, conc0 %01x, poic0 %02x, %02x %02x %02x %02x %02x %02x %02x\n",
- single_toc.addressc0,
- single_toc.controlc0,
- single_toc.pointc0,
- single_toc.dummyc0[0],
- single_toc.dummyc0[1],
- single_toc.dummyc0[2],
- single_toc.dummyc0[3],
- single_toc.dummyc0[4],
- single_toc.dummyc0[5],
- single_toc.dummyc0[6]);
-#undef DEBUG
-#define DEBUG 0
-
- sony_toc.lead_out_start_msf[0] =
- bcd_to_int(single_toc.lead_out_start_msf[0]);
- sony_toc.lead_out_start_msf[1] =
- bcd_to_int(single_toc.lead_out_start_msf[1]);
- sony_toc.lead_out_start_msf[2] =
- bcd_to_int(single_toc.lead_out_start_msf[2]);
- sony_toc.lead_out_start_lba =
- single_toc.lead_out_start_lba =
- msf_to_log(sony_toc.lead_out_start_msf);
-
- /* For points that do not exist, move the data over them
- to the right location. */
- if (single_toc.pointb0 != 0xb0) {
- memmove(((char *) &single_toc) + 27,
- ((char *) &single_toc) + 18,
- res_size - 18);
- res_size += 9;
- } else if (res_size > 18) {
- sony_toc.lead_out_start_msf[0] =
- bcd_to_int(single_toc.
- max_start_outer_leadout_msf
- [0]);
- sony_toc.lead_out_start_msf[1] =
- bcd_to_int(single_toc.
- max_start_outer_leadout_msf
- [1]);
- sony_toc.lead_out_start_msf[2] =
- bcd_to_int(single_toc.
- max_start_outer_leadout_msf
- [2]);
- sony_toc.lead_out_start_lba =
- msf_to_log(sony_toc.
- lead_out_start_msf);
- }
- if (single_toc.pointb1 != 0xb1) {
- memmove(((char *) &single_toc) + 36,
- ((char *) &single_toc) + 27,
- res_size - 27);
- res_size += 9;
- }
- if (single_toc.pointb2 != 0xb2) {
- memmove(((char *) &single_toc) + 45,
- ((char *) &single_toc) + 36,
- res_size - 36);
- res_size += 9;
- }
- if (single_toc.pointb3 != 0xb3) {
- memmove(((char *) &single_toc) + 54,
- ((char *) &single_toc) + 45,
- res_size - 45);
- res_size += 9;
- }
- if (single_toc.pointb4 != 0xb4) {
- memmove(((char *) &single_toc) + 63,
- ((char *) &single_toc) + 54,
- res_size - 54);
- res_size += 9;
- }
- if (single_toc.pointc0 != 0xc0) {
- memmove(((char *) &single_toc) + 72,
- ((char *) &single_toc) + 63,
- res_size - 63);
- res_size += 9;
- }
-#if DEBUG
- printk(PRINT_INFO PFX "start track lba %u, "
- "leadout start lba %u\n",
- single_toc.start_track_lba,
- single_toc.lead_out_start_lba);
- {
- int i;
- for (i = 0;
- i <
- 1 +
- bcd_to_int(single_toc.last_track_num)
- -
- bcd_to_int(single_toc.
- first_track_num); i++) {
- printk(KERN_INFO PFX "trk %02d: add 0x%01x, con 0x%01x, track %02d, start min %02d, sec %02d, frame %02d\n",
- i,
- single_toc.tracks[i].address,
- single_toc.tracks[i].control,
- bcd_to_int(single_toc.
- tracks[i].track),
- bcd_to_int(single_toc.
- tracks[i].
- track_start_msf
- [0]),
- bcd_to_int(single_toc.
- tracks[i].
- track_start_msf
- [1]),
- bcd_to_int(single_toc.
- tracks[i].
- track_start_msf
- [2]));
- if (mint >
- bcd_to_int(single_toc.
- tracks[i].track))
- mint =
- bcd_to_int(single_toc.
- tracks[i].
- track);
- if (maxt <
- bcd_to_int(single_toc.
- tracks[i].track))
- maxt =
- bcd_to_int(single_toc.
- tracks[i].
- track);
- }
- printk(KERN_INFO PFX "min track number %d, "
- "max track number %d\n",
- mint, maxt);
- }
-#endif
-
- /* prepare a special table of contents for a CD-I disc. They don't have one. */
- if (single_toc.disk_type == 0x10 &&
- single_toc.first_track_num == 2 &&
- single_toc.last_track_num == 2 /* CD-I */ ) {
- sony_toc.tracks[totaltracks].address = 1;
- sony_toc.tracks[totaltracks].control = 4; /* force data tracks */
- sony_toc.tracks[totaltracks].track = 1;
- sony_toc.tracks[totaltracks].
- track_start_msf[0] = 0;
- sony_toc.tracks[totaltracks].
- track_start_msf[1] = 2;
- sony_toc.tracks[totaltracks].
- track_start_msf[2] = 0;
- mint = maxt = 1;
- totaltracks++;
- } else
- /* gather track entries from this session */
- {
- int i;
- for (i = 0;
- i <
- 1 +
- bcd_to_int(single_toc.last_track_num)
- -
- bcd_to_int(single_toc.
- first_track_num);
- i++, totaltracks++) {
- sony_toc.tracks[totaltracks].
- address =
- single_toc.tracks[i].address;
- sony_toc.tracks[totaltracks].
- control =
- single_toc.tracks[i].control;
- sony_toc.tracks[totaltracks].
- track =
- bcd_to_int(single_toc.
- tracks[i].track);
- sony_toc.tracks[totaltracks].
- track_start_msf[0] =
- bcd_to_int(single_toc.
- tracks[i].
- track_start_msf[0]);
- sony_toc.tracks[totaltracks].
- track_start_msf[1] =
- bcd_to_int(single_toc.
- tracks[i].
- track_start_msf[1]);
- sony_toc.tracks[totaltracks].
- track_start_msf[2] =
- bcd_to_int(single_toc.
- tracks[i].
- track_start_msf[2]);
- if (i == 0)
- single_toc.
- start_track_lba =
- msf_to_log(sony_toc.
- tracks
- [totaltracks].
- track_start_msf);
- if (mint >
- sony_toc.tracks[totaltracks].
- track)
- mint =
- sony_toc.
- tracks[totaltracks].
- track;
- if (maxt <
- sony_toc.tracks[totaltracks].
- track)
- maxt =
- sony_toc.
- tracks[totaltracks].
- track;
- }
- }
- sony_toc.first_track_num = mint;
- sony_toc.last_track_num = maxt;
- /* Disk type of last session wins. For example:
- CD-Extra has disk type 0 for the first session, so
- a dumb HiFi CD player thinks it is a plain audio CD.
- We are interested in the disk type of the last session,
- which is 0x20 (XA) for CD-Extra, so we can access the
- data track ... */
- sony_toc.disk_type = single_toc.disk_type;
- sony_toc.sessions = session;
-
- /* don't believe everything :-) */
- if (session == 1)
- single_toc.start_track_lba = 0;
- sony_toc.start_track_lba =
- single_toc.start_track_lba;
-
- if (session > 1 && single_toc.pointb0 == 0xb0 &&
- sony_toc.lead_out_start_lba ==
- single_toc.lead_out_start_lba) {
- break;
- }
-
- /* Let's not get carried away... */
- if (session > 40) {
- printk(KERN_NOTICE PFX "too many sessions: "
- "%d\n", session);
- break;
- }
- session++;
- }
- sony_toc.track_entries = totaltracks;
- /* add one entry for the LAST track with track number CDROM_LEADOUT */
- sony_toc.tracks[totaltracks].address = single_toc.address2;
- sony_toc.tracks[totaltracks].control = single_toc.control2;
- sony_toc.tracks[totaltracks].track = CDROM_LEADOUT;
- sony_toc.tracks[totaltracks].track_start_msf[0] =
- sony_toc.lead_out_start_msf[0];
- sony_toc.tracks[totaltracks].track_start_msf[1] =
- sony_toc.lead_out_start_msf[1];
- sony_toc.tracks[totaltracks].track_start_msf[2] =
- sony_toc.lead_out_start_msf[2];
-
- sony_toc_read = 1;
-
- pr_debug(PFX "Disk session %d, start track: %d, "
- "stop track: %d\n",
- session, single_toc.start_track_lba,
- single_toc.lead_out_start_lba);
- }
- pr_debug(PFX "Leaving %s\n", __FUNCTION__);
-}
-
-
-/*
- * Uniform cdrom interface function
- * return multisession offset and sector information
- */
-static int scd_get_last_session(struct cdrom_device_info *cdi,
- struct cdrom_multisession *ms_info)
-{
- if (ms_info == NULL)
- return 1;
-
- if (!sony_toc_read) {
- if (down_interruptible(&sony_sem))
- return -ERESTARTSYS;
- sony_get_toc();
- up(&sony_sem);
- }
-
- ms_info->addr_format = CDROM_LBA;
- ms_info->addr.lba = sony_toc.start_track_lba;
- ms_info->xa_flag = sony_toc.disk_type == SONY_XA_DISK_TYPE ||
- sony_toc.disk_type == 0x10 /* CDI */ ;
-
- return 0;
-}
-
-/*
- * Search for a specific track in the table of contents.
- */
-static int find_track(int track)
-{
- int i;
-
- for (i = 0; i <= sony_toc.track_entries; i++) {
- if (sony_toc.tracks[i].track == track) {
- return i;
- }
- }
-
- return -1;
-}
-
-
-/*
- * Read the subcode and put it in last_sony_subcode for future use.
- */
-static int read_subcode(void)
-{
- unsigned int res_size;
-
-
- do_sony_cd_cmd(SONY_REQ_SUBCODE_ADDRESS_CMD,
- NULL,
- 0, (unsigned char *) &last_sony_subcode, &res_size);
- if ((res_size < 2)
- || ((last_sony_subcode.exec_status[0] & 0xf0) == 0x20)) {
- printk(KERN_ERR PFX "Sony CDROM error %s (read_subcode)\n",
- translate_error(last_sony_subcode.exec_status[1]));
- return -EIO;
- }
-
- last_sony_subcode.track_num =
- bcd_to_int(last_sony_subcode.track_num);
- last_sony_subcode.index_num =
- bcd_to_int(last_sony_subcode.index_num);
- last_sony_subcode.abs_msf[0] =
- bcd_to_int(last_sony_subcode.abs_msf[0]);
- last_sony_subcode.abs_msf[1] =
- bcd_to_int(last_sony_subcode.abs_msf[1]);
- last_sony_subcode.abs_msf[2] =
- bcd_to_int(last_sony_subcode.abs_msf[2]);
-
- last_sony_subcode.rel_msf[0] =
- bcd_to_int(last_sony_subcode.rel_msf[0]);
- last_sony_subcode.rel_msf[1] =
- bcd_to_int(last_sony_subcode.rel_msf[1]);
- last_sony_subcode.rel_msf[2] =
- bcd_to_int(last_sony_subcode.rel_msf[2]);
- return 0;
-}
-
-/*
- * Uniform cdrom interface function
- * return the media catalog number found on some older audio cds
- */
-static int
-scd_get_mcn(struct cdrom_device_info *cdi, struct cdrom_mcn *mcn)
-{
- unsigned char resbuffer[2 + 14];
- unsigned char *mcnp = mcn->medium_catalog_number;
- unsigned char *resp = resbuffer + 3;
- unsigned int res_size;
-
- memset(mcn->medium_catalog_number, 0, 14);
- if (down_interruptible(&sony_sem))
- return -ERESTARTSYS;
- do_sony_cd_cmd(SONY_REQ_UPC_EAN_CMD,
- NULL, 0, resbuffer, &res_size);
- up(&sony_sem);
- if ((res_size < 2) || ((resbuffer[0] & 0xf0) == 0x20));
- else {
- /* packed bcd to single ASCII digits */
- *mcnp++ = (*resp >> 4) + '0';
- *mcnp++ = (*resp++ & 0x0f) + '0';
- *mcnp++ = (*resp >> 4) + '0';
- *mcnp++ = (*resp++ & 0x0f) + '0';
- *mcnp++ = (*resp >> 4) + '0';
- *mcnp++ = (*resp++ & 0x0f) + '0';
- *mcnp++ = (*resp >> 4) + '0';
- *mcnp++ = (*resp++ & 0x0f) + '0';
- *mcnp++ = (*resp >> 4) + '0';
- *mcnp++ = (*resp++ & 0x0f) + '0';
- *mcnp++ = (*resp >> 4) + '0';
- *mcnp++ = (*resp++ & 0x0f) + '0';
- *mcnp++ = (*resp >> 4) + '0';
- }
- *mcnp = '\0';
- return 0;
-}
-
-
-/*
- * Get the subchannel info like the CDROMSUBCHNL command wants to see it. If
- * the drive is playing, the subchannel needs to be read (since it would be
- * changing). If the drive is paused or completed, the subcode information has
- * already been stored, just use that. The ioctl call wants things in decimal
- * (not BCD), so all the conversions are done.
- */
-static int sony_get_subchnl_info(struct cdrom_subchnl *schi)
-{
- /* Get attention stuff */
- while (handle_sony_cd_attention());
-
- sony_get_toc();
- if (!sony_toc_read) {
- return -EIO;
- }
-
- switch (sony_audio_status) {
- case CDROM_AUDIO_NO_STATUS:
- case CDROM_AUDIO_PLAY:
- if (read_subcode() < 0) {
- return -EIO;
- }
- break;
-
- case CDROM_AUDIO_PAUSED:
- case CDROM_AUDIO_COMPLETED:
- break;
-
-#if 0
- case CDROM_AUDIO_NO_STATUS:
- schi->cdsc_audiostatus = sony_audio_status;
- return 0;
- break;
-#endif
- case CDROM_AUDIO_INVALID:
- case CDROM_AUDIO_ERROR:
- default:
- return -EIO;
- }
-
- schi->cdsc_audiostatus = sony_audio_status;
- schi->cdsc_adr = last_sony_subcode.address;
- schi->cdsc_ctrl = last_sony_subcode.control;
- schi->cdsc_trk = last_sony_subcode.track_num;
- schi->cdsc_ind = last_sony_subcode.index_num;
- if (schi->cdsc_format == CDROM_MSF) {
- schi->cdsc_absaddr.msf.minute =
- last_sony_subcode.abs_msf[0];
- schi->cdsc_absaddr.msf.second =
- last_sony_subcode.abs_msf[1];
- schi->cdsc_absaddr.msf.frame =
- last_sony_subcode.abs_msf[2];
-
- schi->cdsc_reladdr.msf.minute =
- last_sony_subcode.rel_msf[0];
- schi->cdsc_reladdr.msf.second =
- last_sony_subcode.rel_msf[1];
- schi->cdsc_reladdr.msf.frame =
- last_sony_subcode.rel_msf[2];
- } else if (schi->cdsc_format == CDROM_LBA) {
- schi->cdsc_absaddr.lba =
- msf_to_log(last_sony_subcode.abs_msf);
- schi->cdsc_reladdr.lba =
- msf_to_log(last_sony_subcode.rel_msf);
- }
-
- return 0;
-}
-
-/* Get audio data from the drive. This is fairly complex because I
- am looking for status and data at the same time, but if I get status
- then I just look for data. I need to get the status immediately so
- the switch from audio to data tracks will happen quickly. */
-static void
-read_audio_data(char *buffer, unsigned char res_reg[], int *res_size)
-{
- unsigned long retry_count;
- int result_read;
-
-
- res_reg[0] = 0;
- res_reg[1] = 0;
- *res_size = 0;
- result_read = 0;
-
- /* Wait for the drive to tell us we have something */
- retry_count = jiffies + SONY_JIFFIES_TIMEOUT;
- continue_read_audio_wait:
- while (time_before(jiffies, retry_count) && !(is_data_ready())
- && !(is_result_ready() || result_read)) {
- while (handle_sony_cd_attention());
-
- sony_sleep();
- }
- if (!(is_data_ready())) {
- if (is_result_ready() && !result_read) {
- get_result(res_reg, res_size);
-
- /* Read block status and continue waiting for data. */
- if ((res_reg[0] & 0xf0) == 0x50) {
- result_read = 1;
- goto continue_read_audio_wait;
- }
- /* Invalid data from the drive. Shut down the operation. */
- else if ((res_reg[0] & 0xf0) != 0x20) {
- printk(KERN_WARNING PFX "Got result that "
- "should have been error: %d\n",
- res_reg[0]);
- res_reg[0] = 0x20;
- res_reg[1] = SONY_BAD_DATA_ERR;
- *res_size = 2;
- }
- abort_read();
- } else {
- pr_debug(PFX "timeout out %d\n", __LINE__);
- res_reg[0] = 0x20;
- res_reg[1] = SONY_TIMEOUT_OP_ERR;
- *res_size = 2;
- abort_read();
- }
- } else {
- clear_data_ready();
-
- /* If data block, then get 2340 bytes offset by 12. */
- if (sony_raw_data_mode) {
- insb(sony_cd_read_reg, buffer + CD_XA_HEAD,
- CD_FRAMESIZE_RAW1);
- } else {
- /* Audio gets the whole 2352 bytes. */
- insb(sony_cd_read_reg, buffer, CD_FRAMESIZE_RAW);
- }
-
- /* If I haven't already gotten the result, get it now. */
- if (!result_read) {
- /* Wait for the drive to tell us we have something */
- retry_count = jiffies + SONY_JIFFIES_TIMEOUT;
- while (time_before(jiffies, retry_count)
- && !(is_result_ready())) {
- while (handle_sony_cd_attention());
-
- sony_sleep();
- }
-
- if (!is_result_ready()) {
- pr_debug(PFX "timeout out %d\n", __LINE__);
- res_reg[0] = 0x20;
- res_reg[1] = SONY_TIMEOUT_OP_ERR;
- *res_size = 2;
- abort_read();
- return;
- } else {
- get_result(res_reg, res_size);
- }
- }
-
- if ((res_reg[0] & 0xf0) == 0x50) {
- if ((res_reg[0] == SONY_NO_CIRC_ERR_BLK_STAT)
- || (res_reg[0] == SONY_NO_LECC_ERR_BLK_STAT)
- || (res_reg[0] == SONY_RECOV_LECC_ERR_BLK_STAT)
- || (res_reg[0] == SONY_NO_ERR_DETECTION_STAT)) {
- /* Ok, nothing to do. */
- } else {
- printk(KERN_ERR PFX "Data block error: 0x%x\n",
- res_reg[0]);
- res_reg[0] = 0x20;
- res_reg[1] = SONY_BAD_DATA_ERR;
- *res_size = 2;
- }
- } else if ((res_reg[0] & 0xf0) != 0x20) {
- /* The drive gave me bad status, I don't know what to do.
- Reset the driver and return an error. */
- printk(KERN_NOTICE PFX "Invalid block status: 0x%x\n",
- res_reg[0]);
- restart_on_error();
- res_reg[0] = 0x20;
- res_reg[1] = SONY_BAD_DATA_ERR;
- *res_size = 2;
- }
- }
-}
-
-/* Perform a raw data read. This will automatically detect the
- track type and read the proper data (audio or data). */
-static int read_audio(struct cdrom_read_audio *ra)
-{
- int retval;
- unsigned char params[2];
- unsigned char res_reg[12];
- unsigned int res_size;
- unsigned int cframe;
-
- if (down_interruptible(&sony_sem))
- return -ERESTARTSYS;
- if (!sony_spun_up)
- scd_spinup();
-
- /* Set the drive to do raw operations. */
- params[0] = SONY_SD_DECODE_PARAM;
- params[1] = 0x06 | sony_raw_data_mode;
- do_sony_cd_cmd(SONY_SET_DRIVE_PARAM_CMD,
- params, 2, res_reg, &res_size);
- if ((res_size < 2) || ((res_reg[0] & 0xf0) == 0x20)) {
- printk(KERN_ERR PFX "Unable to set decode params: 0x%2.2x\n",
- res_reg[1]);
- retval = -EIO;
- goto out_up;
- }
-
- /* From here down, we have to goto exit_read_audio instead of returning
- because the drive parameters have to be set back to data before
- return. */
-
- retval = 0;
- if (start_request(ra->addr.lba, ra->nframes)) {
- retval = -EIO;
- goto exit_read_audio;
- }
-
- /* For every requested frame. */
- cframe = 0;
- while (cframe < ra->nframes) {
- read_audio_data(audio_buffer, res_reg, &res_size);
- if ((res_reg[0] & 0xf0) == 0x20) {
- if (res_reg[1] == SONY_BAD_DATA_ERR) {
- printk(KERN_ERR PFX "Data error on audio "
- "sector %d\n",
- ra->addr.lba + cframe);
- } else if (res_reg[1] == SONY_ILL_TRACK_R_ERR) {
- /* Illegal track type, change track types and start over. */
- sony_raw_data_mode =
- (sony_raw_data_mode) ? 0 : 1;
-
- /* Set the drive mode. */
- params[0] = SONY_SD_DECODE_PARAM;
- params[1] = 0x06 | sony_raw_data_mode;
- do_sony_cd_cmd(SONY_SET_DRIVE_PARAM_CMD,
- params,
- 2, res_reg, &res_size);
- if ((res_size < 2)
- || ((res_reg[0] & 0xf0) == 0x20)) {
- printk(KERN_ERR PFX "Unable to set "
- "decode params: 0x%2.2x\n",
- res_reg[1]);
- retval = -EIO;
- goto exit_read_audio;
- }
-
- /* Restart the request on the current frame. */
- if (start_request
- (ra->addr.lba + cframe,
- ra->nframes - cframe)) {
- retval = -EIO;
- goto exit_read_audio;
- }
-
- /* Don't go back to the top because don't want to get into
- and infinite loop. A lot of code gets duplicated, but
- that's no big deal, I don't guess. */
- read_audio_data(audio_buffer, res_reg,
- &res_size);
- if ((res_reg[0] & 0xf0) == 0x20) {
- if (res_reg[1] ==
- SONY_BAD_DATA_ERR) {
- printk(KERN_ERR PFX "Data error"
- " on audio sector %d\n",
- ra->addr.lba +
- cframe);
- } else {
- printk(KERN_ERR PFX "Error reading audio data on sector %d: %s\n",
- ra->addr.lba + cframe,
- translate_error
- (res_reg[1]));
- retval = -EIO;
- goto exit_read_audio;
- }
- } else if (copy_to_user(ra->buf +
- (CD_FRAMESIZE_RAW
- * cframe),
- audio_buffer,
- CD_FRAMESIZE_RAW)) {
- retval = -EFAULT;
- goto exit_read_audio;
- }
- } else {
- printk(KERN_ERR PFX "Error reading audio "
- "data on sector %d: %s\n",
- ra->addr.lba + cframe,
- translate_error(res_reg[1]));
- retval = -EIO;
- goto exit_read_audio;
- }
- } else if (copy_to_user(ra->buf + (CD_FRAMESIZE_RAW * cframe),
- (char *)audio_buffer,
- CD_FRAMESIZE_RAW)) {
- retval = -EFAULT;
- goto exit_read_audio;
- }
-
- cframe++;
- }
-
- get_result(res_reg, &res_size);
- if ((res_reg[0] & 0xf0) == 0x20) {
- printk(KERN_ERR PFX "Error return from audio read: %s\n",
- translate_error(res_reg[1]));
- retval = -EIO;
- goto exit_read_audio;
- }
-
- exit_read_audio:
-
- /* Set the drive mode back to the proper one for the disk. */
- params[0] = SONY_SD_DECODE_PARAM;
- if (!sony_xa_mode) {
- params[1] = 0x0f;
- } else {
- params[1] = 0x07;
- }
- do_sony_cd_cmd(SONY_SET_DRIVE_PARAM_CMD,
- params, 2, res_reg, &res_size);
- if ((res_size < 2) || ((res_reg[0] & 0xf0) == 0x20)) {
- printk(KERN_ERR PFX "Unable to reset decode params: 0x%2.2x\n",
- res_reg[1]);
- retval = -EIO;
- }
-
- out_up:
- up(&sony_sem);
-
- return retval;
-}
-
-static int
-do_sony_cd_cmd_chk(const char *name,
- unsigned char cmd,
- unsigned char *params,
- unsigned int num_params,
- unsigned char *result_buffer, unsigned int *result_size)
-{
- do_sony_cd_cmd(cmd, params, num_params, result_buffer,
- result_size);
- if ((*result_size < 2) || ((result_buffer[0] & 0xf0) == 0x20)) {
- printk(KERN_ERR PFX "Error %s (CDROM%s)\n",
- translate_error(result_buffer[1]), name);
- return -EIO;
- }
- return 0;
-}
-
-/*
- * Uniform cdrom interface function
- * open the tray
- */
-static int scd_tray_move(struct cdrom_device_info *cdi, int position)
-{
- int retval;
-
- if (down_interruptible(&sony_sem))
- return -ERESTARTSYS;
- if (position == 1 /* open tray */ ) {
- unsigned char res_reg[12];
- unsigned int res_size;
-
- do_sony_cd_cmd(SONY_AUDIO_STOP_CMD, NULL, 0, res_reg,
- &res_size);
- do_sony_cd_cmd(SONY_SPIN_DOWN_CMD, NULL, 0, res_reg,
- &res_size);
-
- sony_audio_status = CDROM_AUDIO_INVALID;
- retval = do_sony_cd_cmd_chk("EJECT", SONY_EJECT_CMD, NULL, 0,
- res_reg, &res_size);
- } else {
- if (0 == scd_spinup())
- sony_spun_up = 1;
- retval = 0;
- }
- up(&sony_sem);
- return retval;
-}
-
-/*
- * The big ugly ioctl handler.
- */
-static int scd_audio_ioctl(struct cdrom_device_info *cdi,
- unsigned int cmd, void *arg)
-{
- unsigned char res_reg[12];
- unsigned int res_size;
- unsigned char params[7];
- int i, retval;
-
- if (down_interruptible(&sony_sem))
- return -ERESTARTSYS;
- switch (cmd) {
- case CDROMSTART: /* Spin up the drive */
- retval = do_sony_cd_cmd_chk("START", SONY_SPIN_UP_CMD, NULL,
- 0, res_reg, &res_size);
- break;
-
- case CDROMSTOP: /* Spin down the drive */
- do_sony_cd_cmd(SONY_AUDIO_STOP_CMD, NULL, 0, res_reg,
- &res_size);
-
- /*
- * Spin the drive down, ignoring the error if the disk was
- * already not spinning.
- */
- sony_audio_status = CDROM_AUDIO_NO_STATUS;
- retval = do_sony_cd_cmd_chk("STOP", SONY_SPIN_DOWN_CMD, NULL,
- 0, res_reg, &res_size);
- break;
-
- case CDROMPAUSE: /* Pause the drive */
- if (do_sony_cd_cmd_chk
- ("PAUSE", SONY_AUDIO_STOP_CMD, NULL, 0, res_reg,
- &res_size)) {
- retval = -EIO;
- break;
- }
- /* Get the current position and save it for resuming */
- if (read_subcode() < 0) {
- retval = -EIO;
- break;
- }
- cur_pos_msf[0] = last_sony_subcode.abs_msf[0];
- cur_pos_msf[1] = last_sony_subcode.abs_msf[1];
- cur_pos_msf[2] = last_sony_subcode.abs_msf[2];
- sony_audio_status = CDROM_AUDIO_PAUSED;
- retval = 0;
- break;
-
- case CDROMRESUME: /* Start the drive after being paused */
- if (sony_audio_status != CDROM_AUDIO_PAUSED) {
- retval = -EINVAL;
- break;
- }
-
- do_sony_cd_cmd(SONY_SPIN_UP_CMD, NULL, 0, res_reg,
- &res_size);
-
- /* Start the drive at the saved position. */
- params[1] = int_to_bcd(cur_pos_msf[0]);
- params[2] = int_to_bcd(cur_pos_msf[1]);
- params[3] = int_to_bcd(cur_pos_msf[2]);
- params[4] = int_to_bcd(final_pos_msf[0]);
- params[5] = int_to_bcd(final_pos_msf[1]);
- params[6] = int_to_bcd(final_pos_msf[2]);
- params[0] = 0x03;
- if (do_sony_cd_cmd_chk
- ("RESUME", SONY_AUDIO_PLAYBACK_CMD, params, 7, res_reg,
- &res_size) < 0) {
- retval = -EIO;
- break;
- }
- sony_audio_status = CDROM_AUDIO_PLAY;
- retval = 0;
- break;
-
- case CDROMPLAYMSF: /* Play starting at the given MSF address. */
- do_sony_cd_cmd(SONY_SPIN_UP_CMD, NULL, 0, res_reg,
- &res_size);
-
- /* The parameters are given in int, must be converted */
- for (i = 1; i < 7; i++) {
- params[i] =
- int_to_bcd(((unsigned char *) arg)[i - 1]);
- }
- params[0] = 0x03;
- if (do_sony_cd_cmd_chk
- ("PLAYMSF", SONY_AUDIO_PLAYBACK_CMD, params, 7,
- res_reg, &res_size) < 0) {
- retval = -EIO;
- break;
- }
-
- /* Save the final position for pauses and resumes */
- final_pos_msf[0] = bcd_to_int(params[4]);
- final_pos_msf[1] = bcd_to_int(params[5]);
- final_pos_msf[2] = bcd_to_int(params[6]);
- sony_audio_status = CDROM_AUDIO_PLAY;
- retval = 0;
- break;
-
- case CDROMREADTOCHDR: /* Read the table of contents header */
- {
- struct cdrom_tochdr *hdr;
-
- sony_get_toc();
- if (!sony_toc_read) {
- retval = -EIO;
- break;
- }
-
- hdr = (struct cdrom_tochdr *) arg;
- hdr->cdth_trk0 = sony_toc.first_track_num;
- hdr->cdth_trk1 = sony_toc.last_track_num;
- }
- retval = 0;
- break;
-
- case CDROMREADTOCENTRY: /* Read a given table of contents entry */
- {
- struct cdrom_tocentry *entry;
- int track_idx;
- unsigned char *msf_val = NULL;
-
- sony_get_toc();
- if (!sony_toc_read) {
- retval = -EIO;
- break;
- }
-
- entry = (struct cdrom_tocentry *) arg;
-
- track_idx = find_track(entry->cdte_track);
- if (track_idx < 0) {
- retval = -EINVAL;
- break;
- }
-
- entry->cdte_adr =
- sony_toc.tracks[track_idx].address;
- entry->cdte_ctrl =
- sony_toc.tracks[track_idx].control;
- msf_val =
- sony_toc.tracks[track_idx].track_start_msf;
-
- /* Logical buffer address or MSF format requested? */
- if (entry->cdte_format == CDROM_LBA) {
- entry->cdte_addr.lba = msf_to_log(msf_val);
- } else if (entry->cdte_format == CDROM_MSF) {
- entry->cdte_addr.msf.minute = *msf_val;
- entry->cdte_addr.msf.second =
- *(msf_val + 1);
- entry->cdte_addr.msf.frame =
- *(msf_val + 2);
- }
- }
- retval = 0;
- break;
-
- case CDROMPLAYTRKIND: /* Play a track. This currently ignores index. */
- {
- struct cdrom_ti *ti = (struct cdrom_ti *) arg;
- int track_idx;
-
- sony_get_toc();
- if (!sony_toc_read) {
- retval = -EIO;
- break;
- }
-
- if ((ti->cdti_trk0 < sony_toc.first_track_num)
- || (ti->cdti_trk0 > sony_toc.last_track_num)
- || (ti->cdti_trk1 < ti->cdti_trk0)) {
- retval = -EINVAL;
- break;
- }
-
- track_idx = find_track(ti->cdti_trk0);
- if (track_idx < 0) {
- retval = -EINVAL;
- break;
- }
- params[1] =
- int_to_bcd(sony_toc.tracks[track_idx].
- track_start_msf[0]);
- params[2] =
- int_to_bcd(sony_toc.tracks[track_idx].
- track_start_msf[1]);
- params[3] =
- int_to_bcd(sony_toc.tracks[track_idx].
- track_start_msf[2]);
-
- /*
- * If we want to stop after the last track, use the lead-out
- * MSF to do that.
- */
- if (ti->cdti_trk1 >= sony_toc.last_track_num) {
- track_idx = find_track(CDROM_LEADOUT);
- } else {
- track_idx = find_track(ti->cdti_trk1 + 1);
- }
- if (track_idx < 0) {
- retval = -EINVAL;
- break;
- }
- params[4] =
- int_to_bcd(sony_toc.tracks[track_idx].
- track_start_msf[0]);
- params[5] =
- int_to_bcd(sony_toc.tracks[track_idx].
- track_start_msf[1]);
- params[6] =
- int_to_bcd(sony_toc.tracks[track_idx].
- track_start_msf[2]);
- params[0] = 0x03;
-
- do_sony_cd_cmd(SONY_SPIN_UP_CMD, NULL, 0, res_reg,
- &res_size);
-
- do_sony_cd_cmd(SONY_AUDIO_PLAYBACK_CMD, params, 7,
- res_reg, &res_size);
-
- if ((res_size < 2)
- || ((res_reg[0] & 0xf0) == 0x20)) {
- printk(KERN_ERR PFX
- "Params: %x %x %x %x %x %x %x\n",
- params[0], params[1], params[2],
- params[3], params[4], params[5],
- params[6]);
- printk(KERN_ERR PFX
- "Error %s (CDROMPLAYTRKIND)\n",
- translate_error(res_reg[1]));
- retval = -EIO;
- break;
- }
-
- /* Save the final position for pauses and resumes */
- final_pos_msf[0] = bcd_to_int(params[4]);
- final_pos_msf[1] = bcd_to_int(params[5]);
- final_pos_msf[2] = bcd_to_int(params[6]);
- sony_audio_status = CDROM_AUDIO_PLAY;
- retval = 0;
- break;
- }
-
- case CDROMVOLCTRL: /* Volume control. What volume does this change, anyway? */
- {
- struct cdrom_volctrl *volctrl =
- (struct cdrom_volctrl *) arg;
-
- params[0] = SONY_SD_AUDIO_VOLUME;
- params[1] = volctrl->channel0;
- params[2] = volctrl->channel1;
- retval = do_sony_cd_cmd_chk("VOLCTRL",
- SONY_SET_DRIVE_PARAM_CMD,
- params, 3, res_reg,
- &res_size);
- break;
- }
- case CDROMSUBCHNL: /* Get subchannel info */
- retval = sony_get_subchnl_info((struct cdrom_subchnl *) arg);
- break;
-
- default:
- retval = -EINVAL;
- break;
- }
- up(&sony_sem);
- return retval;
-}
-
-static int scd_read_audio(struct cdrom_device_info *cdi,
- unsigned int cmd, unsigned long arg)
-{
- void __user *argp = (void __user *)arg;
- int retval;
-
- if (down_interruptible(&sony_sem))
- return -ERESTARTSYS;
- switch (cmd) {
- case CDROMREADAUDIO: /* Read 2352 byte audio tracks and 2340 byte
- raw data tracks. */
- {
- struct cdrom_read_audio ra;
-
-
- sony_get_toc();
- if (!sony_toc_read) {
- retval = -EIO;
- break;
- }
-
- if (copy_from_user(&ra, argp, sizeof(ra))) {
- retval = -EFAULT;
- break;
- }
-
- if (ra.nframes == 0) {
- retval = 0;
- break;
- }
-
- if (!access_ok(VERIFY_WRITE, ra.buf,
- CD_FRAMESIZE_RAW * ra.nframes))
- return -EFAULT;
-
- if (ra.addr_format == CDROM_LBA) {
- if ((ra.addr.lba >=
- sony_toc.lead_out_start_lba)
- || (ra.addr.lba + ra.nframes >=
- sony_toc.lead_out_start_lba)) {
- retval = -EINVAL;
- break;
- }
- } else if (ra.addr_format == CDROM_MSF) {
- if ((ra.addr.msf.minute >= 75)
- || (ra.addr.msf.second >= 60)
- || (ra.addr.msf.frame >= 75)) {
- retval = -EINVAL;
- break;
- }
-
- ra.addr.lba = ((ra.addr.msf.minute * 4500)
- + (ra.addr.msf.second * 75)
- + ra.addr.msf.frame);
- if ((ra.addr.lba >=
- sony_toc.lead_out_start_lba)
- || (ra.addr.lba + ra.nframes >=
- sony_toc.lead_out_start_lba)) {
- retval = -EINVAL;
- break;
- }
-
- /* I know, this can go negative on an unsigned. However,
- the first thing done to the data is to add this value,
- so this should compensate and allow direct msf access. */
- ra.addr.lba -= LOG_START_OFFSET;
- } else {
- retval = -EINVAL;
- break;
- }
-
- retval = read_audio(&ra);
- break;
- }
- retval = 0;
- break;
-
- default:
- retval = -EINVAL;
- }
- up(&sony_sem);
- return retval;
-}
-
-static int scd_spinup(void)
-{
- unsigned char res_reg[12];
- unsigned int res_size;
- int num_spin_ups;
-
- num_spin_ups = 0;
-
- respinup_on_open:
- do_sony_cd_cmd(SONY_SPIN_UP_CMD, NULL, 0, res_reg, &res_size);
-
- /* The drive sometimes returns error 0. I don't know why, but ignore
- it. It seems to mean the drive has already done the operation. */
- if ((res_size < 2) || ((res_reg[0] != 0) && (res_reg[1] != 0))) {
- printk(KERN_ERR PFX "%s error (scd_open, spin up)\n",
- translate_error(res_reg[1]));
- return 1;
- }
-
- do_sony_cd_cmd(SONY_READ_TOC_CMD, NULL, 0, res_reg, &res_size);
-
- /* The drive sometimes returns error 0. I don't know why, but ignore
- it. It seems to mean the drive has already done the operation. */
- if ((res_size < 2) || ((res_reg[0] != 0) && (res_reg[1] != 0))) {
- /* If the drive is already playing, it's ok. */
- if ((res_reg[1] == SONY_AUDIO_PLAYING_ERR)
- || (res_reg[1] == 0)) {
- return 0;
- }
-
- /* If the drive says it is not spun up (even though we just did it!)
- then retry the operation at least a few times. */
- if ((res_reg[1] == SONY_NOT_SPIN_ERR)
- && (num_spin_ups < MAX_CDU31A_RETRIES)) {
- num_spin_ups++;
- goto respinup_on_open;
- }
-
- printk(KERN_ERR PFX "Error %s (scd_open, read toc)\n",
- translate_error(res_reg[1]));
- do_sony_cd_cmd(SONY_SPIN_DOWN_CMD, NULL, 0, res_reg,
- &res_size);
- return 1;
- }
- return 0;
-}
-
-/*
- * Open the drive for operations. Spin the drive up and read the table of
- * contents if these have not already been done.
- */
-static int scd_open(struct cdrom_device_info *cdi, int purpose)
-{
- unsigned char res_reg[12];
- unsigned int res_size;
- unsigned char params[2];
-
- if (purpose == 1) {
- /* Open for IOCTLs only - no media check */
- sony_usage++;
- return 0;
- }
-
- if (sony_usage == 0) {
- if (scd_spinup() != 0)
- return -EIO;
- sony_get_toc();
- if (!sony_toc_read) {
- do_sony_cd_cmd(SONY_SPIN_DOWN_CMD, NULL, 0,
- res_reg, &res_size);
- return -EIO;
- }
-
- /* For XA on the CDU31A only, we have to do special reads.
- The CDU33A handles XA automagically. */
- /* if ( (sony_toc.disk_type == SONY_XA_DISK_TYPE) */
- if ((sony_toc.disk_type != 0x00)
- && (!is_double_speed)) {
- params[0] = SONY_SD_DECODE_PARAM;
- params[1] = 0x07;
- do_sony_cd_cmd(SONY_SET_DRIVE_PARAM_CMD,
- params, 2, res_reg, &res_size);
- if ((res_size < 2)
- || ((res_reg[0] & 0xf0) == 0x20)) {
- printk(KERN_WARNING PFX "Unable to set "
- "XA params: 0x%2.2x\n", res_reg[1]);
- }
- sony_xa_mode = 1;
- }
- /* A non-XA disk. Set the parms back if necessary. */
- else if (sony_xa_mode) {
- params[0] = SONY_SD_DECODE_PARAM;
- params[1] = 0x0f;
- do_sony_cd_cmd(SONY_SET_DRIVE_PARAM_CMD,
- params, 2, res_reg, &res_size);
- if ((res_size < 2)
- || ((res_reg[0] & 0xf0) == 0x20)) {
- printk(KERN_WARNING PFX "Unable to reset "
- "XA params: 0x%2.2x\n", res_reg[1]);
- }
- sony_xa_mode = 0;
- }
-
- sony_spun_up = 1;
- }
-
- sony_usage++;
-
- return 0;
-}
-
-
-/*
- * Close the drive. Spin it down if no task is using it. The spin
- * down will fail if playing audio, so audio play is OK.
- */
-static void scd_release(struct cdrom_device_info *cdi)
-{
- if (sony_usage == 1) {
- unsigned char res_reg[12];
- unsigned int res_size;
-
- do_sony_cd_cmd(SONY_SPIN_DOWN_CMD, NULL, 0, res_reg,
- &res_size);
-
- sony_spun_up = 0;
- }
- sony_usage--;
-}
-
-static struct cdrom_device_ops scd_dops = {
- .open = scd_open,
- .release = scd_release,
- .drive_status = scd_drive_status,
- .media_changed = scd_media_changed,
- .tray_move = scd_tray_move,
- .lock_door = scd_lock_door,
- .select_speed = scd_select_speed,
- .get_last_session = scd_get_last_session,
- .get_mcn = scd_get_mcn,
- .reset = scd_reset,
- .audio_ioctl = scd_audio_ioctl,
- .capability = CDC_OPEN_TRAY | CDC_CLOSE_TRAY | CDC_LOCK |
- CDC_SELECT_SPEED | CDC_MULTI_SESSION |
- CDC_MCN | CDC_MEDIA_CHANGED | CDC_PLAY_AUDIO |
- CDC_RESET | CDC_DRIVE_STATUS,
- .n_minors = 1,
-};
-
-static struct cdrom_device_info scd_info = {
- .ops = &scd_dops,
- .speed = 2,
- .capacity = 1,
- .name = "cdu31a"
-};
-
-static int scd_block_open(struct inode *inode, struct file *file)
-{
- return cdrom_open(&scd_info, inode, file);
-}
-
-static int scd_block_release(struct inode *inode, struct file *file)
-{
- return cdrom_release(&scd_info, file);
-}
-
-static int scd_block_ioctl(struct inode *inode, struct file *file,
- unsigned cmd, unsigned long arg)
-{
- int retval;
-
- /* The eject and close commands should be handled by Uniform CD-ROM
- * driver - but I always got hard lockup instead of eject
- * until I put this here.
- */
- switch (cmd) {
- case CDROMEJECT:
- scd_lock_door(&scd_info, 0);
- retval = scd_tray_move(&scd_info, 1);
- break;
- case CDROMCLOSETRAY:
- retval = scd_tray_move(&scd_info, 0);
- break;
- case CDROMREADAUDIO:
- retval = scd_read_audio(&scd_info, CDROMREADAUDIO, arg);
- break;
- default:
- retval = cdrom_ioctl(file, &scd_info, inode, cmd, arg);
- }
- return retval;
-}
-
-static int scd_block_media_changed(struct gendisk *disk)
-{
- return cdrom_media_changed(&scd_info);
-}
-
-static struct block_device_operations scd_bdops =
-{
- .owner = THIS_MODULE,
- .open = scd_block_open,
- .release = scd_block_release,
- .ioctl = scd_block_ioctl,
- .media_changed = scd_block_media_changed,
-};
-
-static struct gendisk *scd_gendisk;
-
-/* The different types of disc loading mechanisms supported */
-static char *load_mech[] __initdata =
- { "caddy", "tray", "pop-up", "unknown" };
-
-static int __init
-get_drive_configuration(unsigned short base_io,
- unsigned char res_reg[], unsigned int *res_size)
-{
- unsigned long retry_count;
-
-
- if (!request_region(base_io, 4, "cdu31a"))
- return 0;
-
- /* Set the base address */
- cdu31a_port = base_io;
-
- /* Set up all the register locations */
- sony_cd_cmd_reg = cdu31a_port + SONY_CMD_REG_OFFSET;
- sony_cd_param_reg = cdu31a_port + SONY_PARAM_REG_OFFSET;
- sony_cd_write_reg = cdu31a_port + SONY_WRITE_REG_OFFSET;
- sony_cd_control_reg = cdu31a_port + SONY_CONTROL_REG_OFFSET;
- sony_cd_status_reg = cdu31a_port + SONY_STATUS_REG_OFFSET;
- sony_cd_result_reg = cdu31a_port + SONY_RESULT_REG_OFFSET;
- sony_cd_read_reg = cdu31a_port + SONY_READ_REG_OFFSET;
- sony_cd_fifost_reg = cdu31a_port + SONY_FIFOST_REG_OFFSET;
-
- /*
- * Check to see if anything exists at the status register location.
- * I don't know if this is a good way to check, but it seems to work
- * ok for me.
- */
- if (read_status_register() != 0xff) {
- /*
- * Reset the drive and wait for attention from it (to say it's reset).
- * If you don't wait, the next operation will probably fail.
- */
- reset_drive();
- retry_count = jiffies + SONY_RESET_TIMEOUT;
- while (time_before(jiffies, retry_count)
- && (!is_attention())) {
- sony_sleep();
- }
-
-#if 0
- /* If attention is never seen probably not a CDU31a present */
- if (!is_attention()) {
- res_reg[0] = 0x20;
- goto out_err;
- }
-#endif
-
- /*
- * Get the drive configuration.
- */
- do_sony_cd_cmd(SONY_REQ_DRIVE_CONFIG_CMD,
- NULL,
- 0, (unsigned char *) res_reg, res_size);
- if (*res_size <= 2 || (res_reg[0] & 0xf0) != 0)
- goto out_err;
- return 1;
- }
-
- /* Return an error */
- res_reg[0] = 0x20;
-out_err:
- release_region(cdu31a_port, 4);
- cdu31a_port = 0;
- return 0;
-}
-
-#ifndef MODULE
-/*
- * Set up base I/O and interrupts, called from main.c.
- */
-
-static int __init cdu31a_setup(char *strings)
-{
- int ints[4];
-
- (void) get_options(strings, ARRAY_SIZE(ints), ints);
-
- if (ints[0] > 0) {
- cdu31a_port = ints[1];
- }
- if (ints[0] > 1) {
- cdu31a_irq = ints[2];
- }
- if ((strings != NULL) && (*strings != '\0')) {
- if (strcmp(strings, "PAS") == 0) {
- sony_pas_init = 1;
- } else {
- printk(KERN_NOTICE PFX "Unknown interface type: %s\n",
- strings);
- }
- }
-
- return 1;
-}
-
-__setup("cdu31a=", cdu31a_setup);
-
-#endif
-
-/*
- * Initialize the driver.
- */
-int __init cdu31a_init(void)
-{
- struct s_sony_drive_config drive_config;
- struct gendisk *disk;
- int deficiency = 0;
- unsigned int res_size;
- char msg[255];
- char buf[40];
- int i;
- int tmp_irq;
-
- /*
- * According to Alex Freed (freed@europa.orion.adobe.com), this is
- * required for the Fusion CD-16 package. If the sound driver is
- * loaded, it should work fine, but just in case...
- *
- * The following turn on the CD-ROM interface for a Fusion CD-16.
- */
- if (sony_pas_init) {
- outb(0xbc, 0x9a01);
- outb(0xe2, 0x9a01);
- }
-
- /* Setting the base I/O address to 0xffff will disable it. */
- if (cdu31a_port == 0xffff)
- goto errout3;
-
- if (cdu31a_port != 0) {
- /* Need IRQ 0 because we can't sleep here. */
- tmp_irq = cdu31a_irq;
- cdu31a_irq = 0;
- if (!get_drive_configuration(cdu31a_port,
- drive_config.exec_status,
- &res_size))
- goto errout3;
- cdu31a_irq = tmp_irq;
- } else {
- cdu31a_irq = 0;
- for (i = 0; cdu31a_addresses[i].base; i++) {
- if (get_drive_configuration(cdu31a_addresses[i].base,
- drive_config.exec_status,
- &res_size)) {
- cdu31a_irq = cdu31a_addresses[i].int_num;
- break;
- }
- }
- if (!cdu31a_port)
- goto errout3;
- }
-
- if (register_blkdev(MAJOR_NR, "cdu31a"))
- goto errout2;
-
- disk = alloc_disk(1);
- if (!disk)
- goto errout1;
- disk->major = MAJOR_NR;
- disk->first_minor = 0;
- sprintf(disk->disk_name, "cdu31a");
- disk->fops = &scd_bdops;
- disk->flags = GENHD_FL_CD;
-
- if (SONY_HWC_DOUBLE_SPEED(drive_config))
- is_double_speed = 1;
-
- tmp_irq = cdu31a_irq; /* Need IRQ 0 because we can't sleep here. */
- cdu31a_irq = 0;
-
- sony_speed = is_double_speed; /* Set 2X drives to 2X by default */
- set_drive_params(sony_speed);
-
- cdu31a_irq = tmp_irq;
-
- if (cdu31a_irq > 0) {
- if (request_irq
- (cdu31a_irq, cdu31a_interrupt, IRQF_DISABLED,
- "cdu31a", NULL)) {
- printk(KERN_WARNING PFX "Unable to grab IRQ%d for "
- "the CDU31A driver\n", cdu31a_irq);
- cdu31a_irq = 0;
- }
- }
-
- sprintf(msg, "Sony I/F CDROM : %8.8s %16.16s %8.8s\n",
- drive_config.vendor_id,
- drive_config.product_id,
- drive_config.product_rev_level);
- sprintf(buf, " Capabilities: %s",
- load_mech[SONY_HWC_GET_LOAD_MECH(drive_config)]);
- strcat(msg, buf);
- if (SONY_HWC_AUDIO_PLAYBACK(drive_config))
- strcat(msg, ", audio");
- else
- deficiency |= CDC_PLAY_AUDIO;
- if (SONY_HWC_EJECT(drive_config))
- strcat(msg, ", eject");
- else
- deficiency |= CDC_OPEN_TRAY;
- if (SONY_HWC_LED_SUPPORT(drive_config))
- strcat(msg, ", LED");
- if (SONY_HWC_ELECTRIC_VOLUME(drive_config))
- strcat(msg, ", elec. Vol");
- if (SONY_HWC_ELECTRIC_VOLUME_CTL(drive_config))
- strcat(msg, ", sep. Vol");
- if (is_double_speed)
- strcat(msg, ", double speed");
- else
- deficiency |= CDC_SELECT_SPEED;
- if (cdu31a_irq > 0) {
- sprintf(buf, ", irq %d", cdu31a_irq);
- strcat(msg, buf);
- }
- strcat(msg, "\n");
- printk(KERN_INFO PFX "%s",msg);
-
- cdu31a_queue = blk_init_queue(do_cdu31a_request, &cdu31a_lock);
- if (!cdu31a_queue)
- goto errout0;
- blk_queue_hardsect_size(cdu31a_queue, 2048);
-
- init_timer(&cdu31a_abort_timer);
- cdu31a_abort_timer.function = handle_abort_timeout;
-
- scd_info.mask = deficiency;
- scd_gendisk = disk;
- if (register_cdrom(&scd_info))
- goto err;
- disk->queue = cdu31a_queue;
- add_disk(disk);
-
- disk_changed = 1;
- return 0;
-
-err:
- blk_cleanup_queue(cdu31a_queue);
-errout0:
- if (cdu31a_irq)
- free_irq(cdu31a_irq, NULL);
- printk(KERN_ERR PFX "Unable to register with Uniform cdrom driver\n");
- put_disk(disk);
-errout1:
- if (unregister_blkdev(MAJOR_NR, "cdu31a")) {
- printk(KERN_WARNING PFX "Can't unregister block device\n");
- }
-errout2:
- release_region(cdu31a_port, 4);
-errout3:
- return -EIO;
-}
-
-
-static void __exit cdu31a_exit(void)
-{
- del_gendisk(scd_gendisk);
- put_disk(scd_gendisk);
- if (unregister_cdrom(&scd_info)) {
- printk(KERN_WARNING PFX "Can't unregister from Uniform "
- "cdrom driver\n");
- return;
- }
- if ((unregister_blkdev(MAJOR_NR, "cdu31a") == -EINVAL)) {
- printk(KERN_WARNING PFX "Can't unregister\n");
- return;
- }
-
- blk_cleanup_queue(cdu31a_queue);
-
- if (cdu31a_irq > 0)
- free_irq(cdu31a_irq, NULL);
-
- release_region(cdu31a_port, 4);
- printk(KERN_INFO PFX "module released.\n");
-}
-
-#ifdef MODULE
-module_init(cdu31a_init);
-#endif
-module_exit(cdu31a_exit);
-
-MODULE_LICENSE("GPL");
-MODULE_ALIAS_BLOCKDEV_MAJOR(CDU31A_CDROM_MAJOR);