1 files changed, 387 insertions, 72 deletions

diff --git a/drivers/clk/tegra/clk-dfll.c b/drivers/clk/tegra/clk-dfll.c
index 609e363dabf8..0400e5b1d627 100644
--- a/drivers/clk/tegra/clk-dfll.c
+++ b/drivers/clk/tegra/clk-dfll.c
@@ -1,7 +1,7 @@
 /*
  * clk-dfll.c - Tegra DFLL clock source common code
  *
- * Copyright (C) 2012-2014 NVIDIA Corporation. All rights reserved.
+ * Copyright (C) 2012-2019 NVIDIA Corporation. All rights reserved.
  *
  * Aleksandr Frid <afrid@nvidia.com>
  * Paul Walmsley <pwalmsley@nvidia.com>
@@ -47,6 +47,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/of.h>
+#include <linux/pinctrl/consumer.h>
 #include <linux/pm_opp.h>
 #include <linux/pm_runtime.h>
 #include <linux/regmap.h>
@@ -243,6 +244,12 @@ enum dfll_tune_range {
 	DFLL_TUNE_LOW = 1,
 };
 
+
+enum tegra_dfll_pmu_if {
+	TEGRA_DFLL_PMU_I2C = 0,
+	TEGRA_DFLL_PMU_PWM = 1,
+};
+
 /**
  * struct dfll_rate_req - target DFLL rate request data
  * @rate: target frequency, after the postscaling
@@ -300,10 +307,19 @@ struct tegra_dfll {
 	u32				i2c_reg;
 	u32				i2c_slave_addr;
 
-	/* i2c_lut array entries are regulator framework selectors */
-	unsigned			i2c_lut[MAX_DFLL_VOLTAGES];
-	int				i2c_lut_size;
-	u8				lut_min, lut_max, lut_safe;
+	/* lut array entries are regulator framework selectors or PWM values*/
+	unsigned			lut[MAX_DFLL_VOLTAGES];
+	unsigned long			lut_uv[MAX_DFLL_VOLTAGES];
+	int				lut_size;
+	u8				lut_bottom, lut_min, lut_max, lut_safe;
+
+	/* PWM interface */
+	enum tegra_dfll_pmu_if		pmu_if;
+	unsigned long			pwm_rate;
+	struct pinctrl			*pwm_pin;
+	struct pinctrl_state		*pwm_enable_state;
+	struct pinctrl_state		*pwm_disable_state;
+	u32				reg_init_uV;
 };
 
 #define clk_hw_to_dfll(_hw) container_of(_hw, struct tegra_dfll, dfll_clk_hw)
@@ -490,6 +506,34 @@ static void dfll_set_mode(struct tegra_dfll *td,
 }
 
 /*
+ * DVCO rate control
+ */
+
+static unsigned long get_dvco_rate_below(struct tegra_dfll *td, u8 out_min)
+{
+	struct dev_pm_opp *opp;
+	unsigned long rate, prev_rate;
+	unsigned long uv, min_uv;
+
+	min_uv = td->lut_uv[out_min];
+	for (rate = 0, prev_rate = 0; ; rate++) {
+		opp = dev_pm_opp_find_freq_ceil(td->soc->dev, &rate);
+		if (IS_ERR(opp))
+			break;
+
+		uv = dev_pm_opp_get_voltage(opp);
+		dev_pm_opp_put(opp);
+
+		if (uv && uv > min_uv)
+			return prev_rate;
+
+		prev_rate = rate;
+	}
+
+	return prev_rate;
+}
+
+/*
  * DFLL-to-I2C controller interface
  */
 
@@ -518,6 +562,118 @@ static int dfll_i2c_set_output_enabled(struct tegra_dfll *td, bool enable)
 	return 0;
 }
 
+
+/*
+ * DFLL-to-PWM controller interface
+ */
+
+/**
+ * dfll_pwm_set_output_enabled - enable/disable PWM voltage requests
+ * @td: DFLL instance
+ * @enable: whether to enable or disable the PWM voltage requests
+ *
+ * Set the master enable control for PWM control value updates. If disabled,
+ * then the PWM signal is not driven. Also configure the PWM output pad
+ * to the appropriate state.
+ */
+static int dfll_pwm_set_output_enabled(struct tegra_dfll *td, bool enable)
+{
+	int ret;
+	u32 val, div;
+
+	if (enable) {
+		ret = pinctrl_select_state(td->pwm_pin, td->pwm_enable_state);
+		if (ret < 0) {
+			dev_err(td->dev, "setting enable state failed\n");
+			return -EINVAL;
+		}
+		val = dfll_readl(td, DFLL_OUTPUT_CFG);
+		val &= ~DFLL_OUTPUT_CFG_PWM_DIV_MASK;
+		div = DIV_ROUND_UP(td->ref_rate, td->pwm_rate);
+		val |= (div << DFLL_OUTPUT_CFG_PWM_DIV_SHIFT)
+				& DFLL_OUTPUT_CFG_PWM_DIV_MASK;
+		dfll_writel(td, val, DFLL_OUTPUT_CFG);
+		dfll_wmb(td);
+
+		val |= DFLL_OUTPUT_CFG_PWM_ENABLE;
+		dfll_writel(td, val, DFLL_OUTPUT_CFG);
+		dfll_wmb(td);
+	} else {
+		ret = pinctrl_select_state(td->pwm_pin, td->pwm_disable_state);
+		if (ret < 0)
+			dev_warn(td->dev, "setting disable state failed\n");
+
+		val = dfll_readl(td, DFLL_OUTPUT_CFG);
+		val &= ~DFLL_OUTPUT_CFG_PWM_ENABLE;
+		dfll_writel(td, val, DFLL_OUTPUT_CFG);
+		dfll_wmb(td);
+	}
+
+	return 0;
+}
+
+/**
+ * dfll_set_force_output_value - set fixed value for force output
+ * @td: DFLL instance
+ * @out_val: value to force output
+ *
+ * Set the fixed value for force output, DFLL will output this value when
+ * force output is enabled.
+ */
+static u32 dfll_set_force_output_value(struct tegra_dfll *td, u8 out_val)
+{
+	u32 val = dfll_readl(td, DFLL_OUTPUT_FORCE);
+
+	val = (val & DFLL_OUTPUT_FORCE_ENABLE) | (out_val & OUT_MASK);
+	dfll_writel(td, val, DFLL_OUTPUT_FORCE);
+	dfll_wmb(td);
+
+	return dfll_readl(td, DFLL_OUTPUT_FORCE);
+}
+
+/**
+ * dfll_set_force_output_enabled - enable/disable force output
+ * @td: DFLL instance
+ * @enable: whether to enable or disable the force output
+ *
+ * Set the enable control for fouce output with fixed value.
+ */
+static void dfll_set_force_output_enabled(struct tegra_dfll *td, bool enable)
+{
+	u32 val = dfll_readl(td, DFLL_OUTPUT_FORCE);
+
+	if (enable)
+		val |= DFLL_OUTPUT_FORCE_ENABLE;
+	else
+		val &= ~DFLL_OUTPUT_FORCE_ENABLE;
+
+	dfll_writel(td, val, DFLL_OUTPUT_FORCE);
+	dfll_wmb(td);
+}
+
+/**
+ * dfll_force_output - force output a fixed value
+ * @td: DFLL instance
+ * @out_sel: value to force output
+ *
+ * Set the fixed value for force output, DFLL will output this value.
+ */
+static int dfll_force_output(struct tegra_dfll *td, unsigned int out_sel)
+{
+	u32 val;
+
+	if (out_sel > OUT_MASK)
+		return -EINVAL;
+
+	val = dfll_set_force_output_value(td, out_sel);
+	if ((td->mode < DFLL_CLOSED_LOOP) &&
+	    !(val & DFLL_OUTPUT_FORCE_ENABLE)) {
+		dfll_set_force_output_enabled(td, true);
+	}
+
+	return 0;
+}
+
 /**
  * dfll_load_lut - load the voltage lookup table
  * @td: struct tegra_dfll *
@@ -539,7 +695,7 @@ static void dfll_load_i2c_lut(struct tegra_dfll *td)
 			lut_index = i;
 
 		val = regulator_list_hardware_vsel(td->vdd_reg,
-						     td->i2c_lut[lut_index]);
+						     td->lut[lut_index]);
 		__raw_writel(val, td->lut_base + i * 4);
 	}
 
@@ -594,24 +750,41 @@ static void dfll_init_out_if(struct tegra_dfll *td)
 {
 	u32 val;
 
-	td->lut_min = 0;
-	td->lut_max = td->i2c_lut_size - 1;
-	td->lut_safe = td->lut_min + 1;
+	td->lut_min = td->lut_bottom;
+	td->lut_max = td->lut_size - 1;
+	td->lut_safe = td->lut_min + (td->lut_min < td->lut_max ? 1 : 0);
+
+	/* clear DFLL_OUTPUT_CFG before setting new value */
+	dfll_writel(td, 0, DFLL_OUTPUT_CFG);
+	dfll_wmb(td);
 
-	dfll_i2c_writel(td, 0, DFLL_OUTPUT_CFG);
 	val = (td->lut_safe << DFLL_OUTPUT_CFG_SAFE_SHIFT) |
-		(td->lut_max << DFLL_OUTPUT_CFG_MAX_SHIFT) |
-		(td->lut_min << DFLL_OUTPUT_CFG_MIN_SHIFT);
-	dfll_i2c_writel(td, val, DFLL_OUTPUT_CFG);
-	dfll_i2c_wmb(td);
+	      (td->lut_max << DFLL_OUTPUT_CFG_MAX_SHIFT) |
+	      (td->lut_min << DFLL_OUTPUT_CFG_MIN_SHIFT);
+	dfll_writel(td, val, DFLL_OUTPUT_CFG);
+	dfll_wmb(td);
 
 	dfll_writel(td, 0, DFLL_OUTPUT_FORCE);
 	dfll_i2c_writel(td, 0, DFLL_INTR_EN);
 	dfll_i2c_writel(td, DFLL_INTR_MAX_MASK | DFLL_INTR_MIN_MASK,
 			DFLL_INTR_STS);
 
-	dfll_load_i2c_lut(td);
-	dfll_init_i2c_if(td);
+	if (td->pmu_if == TEGRA_DFLL_PMU_PWM) {
+		u32 vinit = td->reg_init_uV;
+		int vstep = td->soc->alignment.step_uv;
+		unsigned long vmin = td->lut_uv[0];
+
+		/* set initial voltage */
+		if ((vinit >= vmin) && vstep) {
+			unsigned int vsel;
+
+			vsel = DIV_ROUND_UP((vinit - vmin), vstep);
+			dfll_force_output(td, vsel);
+		}
+	} else {
+		dfll_load_i2c_lut(td);
+		dfll_init_i2c_if(td);
+	}
 }
 
 /*
@@ -631,17 +804,17 @@ static void dfll_init_out_if(struct tegra_dfll *td)
 static int find_lut_index_for_rate(struct tegra_dfll *td, unsigned long rate)
 {
 	struct dev_pm_opp *opp;
-	int i, uv;
+	int i, align_step;
 
 	opp = dev_pm_opp_find_freq_ceil(td->soc->dev, &rate);
 	if (IS_ERR(opp))
 		return PTR_ERR(opp);
 
-	uv = dev_pm_opp_get_voltage(opp);
+	align_step = dev_pm_opp_get_voltage(opp) / td->soc->alignment.step_uv;
 	dev_pm_opp_put(opp);
 
-	for (i = 0; i < td->i2c_lut_size; i++) {
-		if (regulator_list_voltage(td->vdd_reg, td->i2c_lut[i]) == uv)
+	for (i = td->lut_bottom; i < td->lut_size; i++) {
+		if ((td->lut_uv[i] / td->soc->alignment.step_uv) >= align_step)
 			return i;
 	}
 
@@ -863,9 +1036,14 @@ static int dfll_lock(struct tegra_dfll *td)
 			return -EINVAL;
 		}
 
-		dfll_i2c_set_output_enabled(td, true);
+		if (td->pmu_if == TEGRA_DFLL_PMU_PWM)
+			dfll_pwm_set_output_enabled(td, true);
+		else
+			dfll_i2c_set_output_enabled(td, true);
+
 		dfll_set_mode(td, DFLL_CLOSED_LOOP);
 		dfll_set_frequency_request(td, req);
+		dfll_set_force_output_enabled(td, false);
 		return 0;
 
 	default:
@@ -889,7 +1067,10 @@ static int dfll_unlock(struct tegra_dfll *td)
 	case DFLL_CLOSED_LOOP:
 		dfll_set_open_loop_config(td);
 		dfll_set_mode(td, DFLL_OPEN_LOOP);
-		dfll_i2c_set_output_enabled(td, false);
+		if (td->pmu_if == TEGRA_DFLL_PMU_PWM)
+			dfll_pwm_set_output_enabled(td, false);
+		else
+			dfll_i2c_set_output_enabled(td, false);
 		return 0;
 
 	case DFLL_OPEN_LOOP:
@@ -1171,15 +1352,17 @@ static int attr_registers_show(struct seq_file *s, void *data)
 		seq_printf(s, "[0x%02x] = 0x%08x\n", offs,
 			   dfll_i2c_readl(td, offs));
 
-	seq_puts(s, "\nINTEGRATED I2C CONTROLLER REGISTERS:\n");
-	offs = DFLL_I2C_CLK_DIVISOR;
-	seq_printf(s, "[0x%02x] = 0x%08x\n", offs,
-		   __raw_readl(td->i2c_controller_base + offs));
-
-	seq_puts(s, "\nLUT:\n");
-	for (offs = 0; offs <  4 * MAX_DFLL_VOLTAGES; offs += 4)
+	if (td->pmu_if == TEGRA_DFLL_PMU_I2C) {
+		seq_puts(s, "\nINTEGRATED I2C CONTROLLER REGISTERS:\n");
+		offs = DFLL_I2C_CLK_DIVISOR;
 		seq_printf(s, "[0x%02x] = 0x%08x\n", offs,
-			   __raw_readl(td->lut_base + offs));
+			   __raw_readl(td->i2c_controller_base + offs));
+
+		seq_puts(s, "\nLUT:\n");
+		for (offs = 0; offs <  4 * MAX_DFLL_VOLTAGES; offs += 4)
+			seq_printf(s, "[0x%02x] = 0x%08x\n", offs,
+				   __raw_readl(td->lut_base + offs));
+	}
 
 	return 0;
 }
@@ -1349,15 +1532,21 @@ di_err1:
  */
 static int find_vdd_map_entry_exact(struct tegra_dfll *td, int uV)
 {
-	int i, n_voltages, reg_uV;
+	int i, n_voltages, reg_uV,reg_volt_id, align_step;
+
+	if (WARN_ON(td->pmu_if == TEGRA_DFLL_PMU_PWM))
+		return -EINVAL;
 
+	align_step = uV / td->soc->alignment.step_uv;
 	n_voltages = regulator_count_voltages(td->vdd_reg);
 	for (i = 0; i < n_voltages; i++) {
 		reg_uV = regulator_list_voltage(td->vdd_reg, i);
 		if (reg_uV < 0)
 			break;
 
-		if (uV == reg_uV)
+		reg_volt_id = reg_uV / td->soc->alignment.step_uv;
+
+		if (align_step == reg_volt_id)
 			return i;
 	}
 
@@ -1371,15 +1560,21 @@ static int find_vdd_map_entry_exact(struct tegra_dfll *td, int uV)
  * */
 static int find_vdd_map_entry_min(struct tegra_dfll *td, int uV)
 {
-	int i, n_voltages, reg_uV;
+	int i, n_voltages, reg_uV, reg_volt_id, align_step;
 
+	if (WARN_ON(td->pmu_if == TEGRA_DFLL_PMU_PWM))
+		return -EINVAL;
+
+	align_step = uV / td->soc->alignment.step_uv;
 	n_voltages = regulator_count_voltages(td->vdd_reg);
 	for (i = 0; i < n_voltages; i++) {
 		reg_uV = regulator_list_voltage(td->vdd_reg, i);
 		if (reg_uV < 0)
 			break;
 
-		if (uV <= reg_uV)
+		reg_volt_id = reg_uV / td->soc->alignment.step_uv;
+
+		if (align_step <= reg_volt_id)
 			return i;
 	}
 
@@ -1387,9 +1582,61 @@ static int find_vdd_map_entry_min(struct tegra_dfll *td, int uV)
 	return -EINVAL;
 }
 
+/*
+ * dfll_build_pwm_lut - build the PWM regulator lookup table
+ * @td: DFLL instance
+ * @v_max: Vmax from OPP table
+ *
+ * Look-up table in h/w is ignored when PWM is used as DFLL interface to PMIC.
+ * In this case closed loop output is controlling duty cycle directly. The s/w
+ * look-up that maps PWM duty cycle to voltage is still built by this function.
+ */
+static int dfll_build_pwm_lut(struct tegra_dfll *td, unsigned long v_max)
+{
+	int i;
+	unsigned long rate, reg_volt;
+	u8 lut_bottom = MAX_DFLL_VOLTAGES;
+	int v_min = td->soc->cvb->min_millivolts * 1000;
+
+	for (i = 0; i < MAX_DFLL_VOLTAGES; i++) {
+		reg_volt = td->lut_uv[i];
+
+		/* since opp voltage is exact mv */
+		reg_volt = (reg_volt / 1000) * 1000;
+		if (reg_volt > v_max)
+			break;
+
+		td->lut[i] = i;
+		if ((lut_bottom == MAX_DFLL_VOLTAGES) && (reg_volt >= v_min))
+			lut_bottom = i;
+	}
+
+	/* determine voltage boundaries */
+	td->lut_size = i;
+	if ((lut_bottom == MAX_DFLL_VOLTAGES) ||
+	    (lut_bottom + 1 >= td->lut_size)) {
+		dev_err(td->dev, "no voltage above DFLL minimum %d mV\n",
+			td->soc->cvb->min_millivolts);
+		return -EINVAL;
+	}
+	td->lut_bottom = lut_bottom;
+
+	/* determine rate boundaries */
+	rate = get_dvco_rate_below(td, td->lut_bottom);
+	if (!rate) {
+		dev_err(td->dev, "no opp below DFLL minimum voltage %d mV\n",
+			td->soc->cvb->min_millivolts);
+		return -EINVAL;
+	}
+	td->dvco_rate_min = rate;
+
+	return 0;
+}
+
 /**
  * dfll_build_i2c_lut - build the I2C voltage register lookup table
  * @td: DFLL instance
+ * @v_max: Vmax from OPP table
  *
  * The DFLL hardware has 33 bytes of look-up table RAM that must be filled with
  * PMIC voltage register values that span the entire DFLL operating range.
@@ -1397,33 +1644,24 @@ static int find_vdd_map_entry_min(struct tegra_dfll *td, int uV)
  * the soc-specific platform driver (td->soc->opp_dev) and the PMIC
  * register-to-voltage mapping queried from the regulator framework.
  *
- * On success, fills in td->i2c_lut and returns 0, or -err on failure.
+ * On success, fills in td->lut and returns 0, or -err on failure.
  */
-static int dfll_build_i2c_lut(struct tegra_dfll *td)
+static int dfll_build_i2c_lut(struct tegra_dfll *td, unsigned long v_max)
 {
+	unsigned long rate, v, v_opp;
 	int ret = -EINVAL;
-	int j, v, v_max, v_opp;
-	int selector;
-	unsigned long rate;
-	struct dev_pm_opp *opp;
-	int lut;
-
-	rate = ULONG_MAX;
-	opp = dev_pm_opp_find_freq_floor(td->soc->dev, &rate);
-	if (IS_ERR(opp)) {
-		dev_err(td->dev, "couldn't get vmax opp, empty opp table?\n");
-		goto out;
-	}
-	v_max = dev_pm_opp_get_voltage(opp);
-	dev_pm_opp_put(opp);
+	int j, selector, lut;
 
 	v = td->soc->cvb->min_millivolts * 1000;
 	lut = find_vdd_map_entry_exact(td, v);
 	if (lut < 0)
 		goto out;
-	td->i2c_lut[0] = lut;
+	td->lut[0] = lut;
+	td->lut_bottom = 0;
 
 	for (j = 1, rate = 0; ; rate++) {
+		struct dev_pm_opp *opp;
+
 		opp = dev_pm_opp_find_freq_ceil(td->soc->dev, &rate);
 		if (IS_ERR(opp))
 			break;
@@ -1435,39 +1673,64 @@ static int dfll_build_i2c_lut(struct tegra_dfll *td)
 		dev_pm_opp_put(opp);
 
 		for (;;) {
-			v += max(1, (v_max - v) / (MAX_DFLL_VOLTAGES - j));
+			v += max(1UL, (v_max - v) / (MAX_DFLL_VOLTAGES - j));
 			if (v >= v_opp)
 				break;
 
 			selector = find_vdd_map_entry_min(td, v);
 			if (selector < 0)
 				goto out;
-			if (selector != td->i2c_lut[j - 1])
-				td->i2c_lut[j++] = selector;
+			if (selector != td->lut[j - 1])
+				td->lut[j++] = selector;
 		}
 
 		v = (j == MAX_DFLL_VOLTAGES - 1) ? v_max : v_opp;
 		selector = find_vdd_map_entry_exact(td, v);
 		if (selector < 0)
 			goto out;
-		if (selector != td->i2c_lut[j - 1])
-			td->i2c_lut[j++] = selector;
+		if (selector != td->lut[j - 1])
+			td->lut[j++] = selector;
 
 		if (v >= v_max)
 			break;
 	}
-	td->i2c_lut_size = j;
+	td->lut_size = j;
 
 	if (!td->dvco_rate_min)
 		dev_err(td->dev, "no opp above DFLL minimum voltage %d mV\n",
 			td->soc->cvb->min_millivolts);
-	else
+	else {
 		ret = 0;
+		for (j = 0; j < td->lut_size; j++)
+			td->lut_uv[j] =
+				regulator_list_voltage(td->vdd_reg,
+						       td->lut[j]);
+	}
 
 out:
 	return ret;
 }
 
+static int dfll_build_lut(struct tegra_dfll *td)
+{
+	unsigned long rate, v_max;
+	struct dev_pm_opp *opp;
+
+	rate = ULONG_MAX;
+	opp = dev_pm_opp_find_freq_floor(td->soc->dev, &rate);
+	if (IS_ERR(opp)) {
+		dev_err(td->dev, "couldn't get vmax opp, empty opp table?\n");
+		return -EINVAL;
+	}
+	v_max = dev_pm_opp_get_voltage(opp);
+	dev_pm_opp_put(opp);
+
+	if (td->pmu_if == TEGRA_DFLL_PMU_PWM)
+		return dfll_build_pwm_lut(td, v_max);
+	else
+		return dfll_build_i2c_lut(td, v_max);
+}
+
 /**
  * read_dt_param - helper function for reading required parameters from the DT
  * @td: DFLL instance
@@ -1526,11 +1789,56 @@ static int dfll_fetch_i2c_params(struct tegra_dfll *td)
 	}
 	td->i2c_reg = vsel_reg;
 
-	ret = dfll_build_i2c_lut(td);
-	if (ret) {
-		dev_err(td->dev, "couldn't build I2C LUT\n");
+	return 0;
+}
+
+static int dfll_fetch_pwm_params(struct tegra_dfll *td)
+{
+	int ret, i;
+	u32 pwm_period;
+
+	if (!td->soc->alignment.step_uv || !td->soc->alignment.offset_uv) {
+		dev_err(td->dev,
+			"Missing step or alignment info for PWM regulator");
+		return -EINVAL;
+	}
+	for (i = 0; i < MAX_DFLL_VOLTAGES; i++)
+		td->lut_uv[i] = td->soc->alignment.offset_uv +
+				i * td->soc->alignment.step_uv;
+
+	ret = read_dt_param(td, "nvidia,pwm-tristate-microvolts",
+			    &td->reg_init_uV);
+	if (!ret) {
+		dev_err(td->dev, "couldn't get initialized voltage\n");
+		return ret;
+	}
+
+	ret = read_dt_param(td, "nvidia,pwm-period-nanoseconds", &pwm_period);
+	if (!ret) {
+		dev_err(td->dev, "couldn't get PWM period\n");
 		return ret;
 	}
+	td->pwm_rate = (NSEC_PER_SEC / pwm_period) * (MAX_DFLL_VOLTAGES - 1);
+
+	td->pwm_pin = devm_pinctrl_get(td->dev);
+	if (IS_ERR(td->pwm_pin)) {
+		dev_err(td->dev, "DT: missing pinctrl device\n");
+		return PTR_ERR(td->pwm_pin);
+	}
+
+	td->pwm_enable_state = pinctrl_lookup_state(td->pwm_pin,
+						    "dvfs_pwm_enable");
+	if (IS_ERR(td->pwm_enable_state)) {
+		dev_err(td->dev, "DT: missing pwm enabled state\n");
+		return PTR_ERR(td->pwm_enable_state);
+	}
+
+	td->pwm_disable_state = pinctrl_lookup_state(td->pwm_pin,
+						     "dvfs_pwm_disable");
+	if (IS_ERR(td->pwm_disable_state)) {
+		dev_err(td->dev, "DT: missing pwm disabled state\n");
+		return PTR_ERR(td->pwm_disable_state);
+	}
 
 	return 0;
 }
@@ -1597,16 +1905,6 @@ int tegra_dfll_register(struct platform_device *pdev,
 
 	td->soc = soc;
 
-	td->vdd_reg = devm_regulator_get(td->dev, "vdd-cpu");
-	if (IS_ERR(td->vdd_reg)) {
-		ret = PTR_ERR(td->vdd_reg);
-		if (ret != -EPROBE_DEFER)
-			dev_err(td->dev, "couldn't get vdd_cpu regulator: %d\n",
-				ret);
-
-		return ret;
-	}
-
 	td->dvco_rst = devm_reset_control_get(td->dev, "dvco");
 	if (IS_ERR(td->dvco_rst)) {
 		dev_err(td->dev, "couldn't get dvco reset\n");
@@ -1619,10 +1917,27 @@ int tegra_dfll_register(struct platform_device *pdev,
 		return ret;
 	}
 
-	ret = dfll_fetch_i2c_params(td);
+	if (of_property_read_bool(td->dev->of_node, "nvidia,pwm-to-pmic")) {
+		td->pmu_if = TEGRA_DFLL_PMU_PWM;
+		ret = dfll_fetch_pwm_params(td);
+	} else  {
+		td->vdd_reg = devm_regulator_get(td->dev, "vdd-cpu");
+		if (IS_ERR(td->vdd_reg)) {
+			dev_err(td->dev, "couldn't get vdd_cpu regulator\n");
+			return PTR_ERR(td->vdd_reg);
+		}
+		td->pmu_if = TEGRA_DFLL_PMU_I2C;
+		ret = dfll_fetch_i2c_params(td);
+	}
 	if (ret)
 		return ret;
 
+	ret = dfll_build_lut(td);
+	if (ret) {
+		dev_err(td->dev, "couldn't build LUT\n");
+		return ret;
+	}
+
 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!mem) {
 		dev_err(td->dev, "no control register resource\n");