diff options
Diffstat (limited to 'drivers/i2c/busses/i2c-sis630.c')
-rw-r--r-- | drivers/i2c/busses/i2c-sis630.c | 360 |
1 files changed, 201 insertions, 159 deletions
diff --git a/drivers/i2c/busses/i2c-sis630.c b/drivers/i2c/busses/i2c-sis630.c index de6dddb9f865..36a9556d7cfa 100644 --- a/drivers/i2c/busses/i2c-sis630.c +++ b/drivers/i2c/busses/i2c-sis630.c @@ -17,30 +17,25 @@ */ /* - Changes: - 24.08.2002 - Fixed the typo in sis630_access (Thanks to Mark M. Hoffman) - Changed sis630_transaction.(Thanks to Mark M. Hoffman) - 18.09.2002 - Added SIS730 as supported. - 21.09.2002 - Added high_clock module option.If this option is set - used Host Master Clock 56KHz (default 14KHz).For now we save old Host - Master Clock and after transaction completed restore (otherwise - it's confuse BIOS and hung Machine). - 24.09.2002 - Fixed typo in sis630_access - Fixed logical error by restoring of Host Master Clock - 31.07.2003 - Added block data read/write support. -*/ - -/* Status: beta Supports: SIS 630 SIS 730 + SIS 964 + + Notable differences between chips: + +------------------------+--------------------+-------------------+ + | | SIS630/730 | SIS964 | + +------------------------+--------------------+-------------------+ + | Clock | 14kHz/56kHz | 55.56kHz/27.78kHz | + | SMBus registers offset | 0x80 | 0xE0 | + | SMB_CNT | Bit 1 = Slave Busy | Bit 1 = Bus probe | + | (not used yet) | Bit 3 is reserved | Bit 3 = Last byte | + | SMB_PCOUNT | Offset + 0x06 | Offset + 0x14 | + | SMB_COUNT | 4:0 bits | 5:0 bits | + +------------------------+--------------------+-------------------+ + (Other differences don't affect the functions provided by the driver) Note: we assume there can only be one device, with one SMBus interface. */ @@ -55,22 +50,36 @@ #include <linux/acpi.h> #include <linux/io.h> -/* SIS630 SMBus registers */ -#define SMB_STS 0x80 /* status */ -#define SMB_EN 0x81 /* status enable */ -#define SMB_CNT 0x82 -#define SMBHOST_CNT 0x83 -#define SMB_ADDR 0x84 -#define SMB_CMD 0x85 -#define SMB_PCOUNT 0x86 /* processed count */ -#define SMB_COUNT 0x87 -#define SMB_BYTE 0x88 /* ~0x8F data byte field */ -#define SMBDEV_ADDR 0x90 -#define SMB_DB0 0x91 -#define SMB_DB1 0x92 -#define SMB_SAA 0x93 - -/* register count for request_region */ +/* SIS964 id is defined here as we are the only file using it */ +#define PCI_DEVICE_ID_SI_964 0x0964 + +/* SIS630/730/964 SMBus registers */ +#define SMB_STS 0x00 /* status */ +#define SMB_CNT 0x02 /* control */ +#define SMBHOST_CNT 0x03 /* host control */ +#define SMB_ADDR 0x04 /* address */ +#define SMB_CMD 0x05 /* command */ +#define SMB_COUNT 0x07 /* byte count */ +#define SMB_BYTE 0x08 /* ~0x8F data byte field */ + +/* SMB_STS register */ +#define BYTE_DONE_STS 0x10 /* Byte Done Status / Block Array */ +#define SMBCOL_STS 0x04 /* Collision */ +#define SMBERR_STS 0x02 /* Device error */ + +/* SMB_CNT register */ +#define MSTO_EN 0x40 /* Host Master Timeout Enable */ +#define SMBCLK_SEL 0x20 /* Host master clock selection */ +#define SMB_PROBE 0x02 /* Bus Probe/Slave busy */ +#define SMB_HOSTBUSY 0x01 /* Host Busy */ + +/* SMBHOST_CNT register */ +#define SMB_KILL 0x20 /* Kill */ +#define SMB_START 0x10 /* Start */ + +/* register count for request_region + * As we don't use SMB_PCOUNT, 20 is ok for SiS630 and SiS964 + */ #define SIS630_SMB_IOREGION 20 /* PCI address constants */ @@ -96,65 +105,71 @@ static struct pci_driver sis630_driver; static bool high_clock; static bool force; module_param(high_clock, bool, 0); -MODULE_PARM_DESC(high_clock, "Set Host Master Clock to 56KHz (default 14KHz)."); +MODULE_PARM_DESC(high_clock, + "Set Host Master Clock to 56KHz (default 14KHz) (SIS630/730 only)."); module_param(force, bool, 0); MODULE_PARM_DESC(force, "Forcibly enable the SIS630. DANGEROUS!"); -/* acpi base address */ -static unsigned short acpi_base; +/* SMBus base adress */ +static unsigned short smbus_base; /* supported chips */ static int supported[] = { PCI_DEVICE_ID_SI_630, PCI_DEVICE_ID_SI_730, + PCI_DEVICE_ID_SI_760, 0 /* terminates the list */ }; static inline u8 sis630_read(u8 reg) { - return inb(acpi_base + reg); + return inb(smbus_base + reg); } static inline void sis630_write(u8 reg, u8 data) { - outb(data, acpi_base + reg); + outb(data, smbus_base + reg); } -static int sis630_transaction_start(struct i2c_adapter *adap, int size, u8 *oldclock) +static int sis630_transaction_start(struct i2c_adapter *adap, int size, + u8 *oldclock) { - int temp; + int temp; /* Make sure the SMBus host is ready to start transmitting. */ - if ((temp = sis630_read(SMB_CNT) & 0x03) != 0x00) { - dev_dbg(&adap->dev, "SMBus busy (%02x).Resetting...\n",temp); + temp = sis630_read(SMB_CNT); + if ((temp & (SMB_PROBE | SMB_HOSTBUSY)) != 0x00) { + dev_dbg(&adap->dev, "SMBus busy (%02x). Resetting...\n", temp); /* kill smbus transaction */ - sis630_write(SMBHOST_CNT, 0x20); + sis630_write(SMBHOST_CNT, SMB_KILL); - if ((temp = sis630_read(SMB_CNT) & 0x03) != 0x00) { + temp = sis630_read(SMB_CNT); + if (temp & (SMB_PROBE | SMB_HOSTBUSY)) { dev_dbg(&adap->dev, "Failed! (%02x)\n", temp); return -EBUSY; - } else { + } else { dev_dbg(&adap->dev, "Successful!\n"); } - } + } /* save old clock, so we can prevent machine for hung */ *oldclock = sis630_read(SMB_CNT); dev_dbg(&adap->dev, "saved clock 0x%02x\n", *oldclock); - /* disable timeout interrupt , set Host Master Clock to 56KHz if requested */ + /* disable timeout interrupt, + * set Host Master Clock to 56KHz if requested */ if (high_clock) - sis630_write(SMB_CNT, 0x20); + sis630_write(SMB_CNT, SMBCLK_SEL); else - sis630_write(SMB_CNT, (*oldclock & ~0x40)); + sis630_write(SMB_CNT, (*oldclock & ~MSTO_EN)); /* clear all sticky bits */ temp = sis630_read(SMB_STS); sis630_write(SMB_STS, temp & 0x1e); /* start the transaction by setting bit 4 and size */ - sis630_write(SMBHOST_CNT,0x10 | (size & 0x07)); + sis630_write(SMBHOST_CNT, SMB_START | (size & 0x07)); return 0; } @@ -168,7 +183,7 @@ static int sis630_transaction_wait(struct i2c_adapter *adap, int size) msleep(1); temp = sis630_read(SMB_STS); /* check if block transmitted */ - if (size == SIS630_BLOCK_DATA && (temp & 0x10)) + if (size == SIS630_BLOCK_DATA && (temp & BYTE_DONE_STS)) break; } while (!(temp & 0x0e) && (timeout++ < MAX_TIMEOUT)); @@ -178,19 +193,14 @@ static int sis630_transaction_wait(struct i2c_adapter *adap, int size) result = -ETIMEDOUT; } - if (temp & 0x02) { + if (temp & SMBERR_STS) { dev_dbg(&adap->dev, "Error: Failed bus transaction\n"); result = -ENXIO; } - if (temp & 0x04) { + if (temp & SMBCOL_STS) { dev_err(&adap->dev, "Bus collision!\n"); - result = -EIO; - /* - TBD: Datasheet say: - the software should clear this bit and restart SMBUS operation. - Should we do it or user start request again? - */ + result = -EAGAIN; } return result; @@ -198,21 +208,21 @@ static int sis630_transaction_wait(struct i2c_adapter *adap, int size) static void sis630_transaction_end(struct i2c_adapter *adap, u8 oldclock) { - int temp = 0; - /* clear all status "sticky" bits */ - sis630_write(SMB_STS, temp); + sis630_write(SMB_STS, 0xFF); - dev_dbg(&adap->dev, "SMB_CNT before clock restore 0x%02x\n", sis630_read(SMB_CNT)); + dev_dbg(&adap->dev, + "SMB_CNT before clock restore 0x%02x\n", sis630_read(SMB_CNT)); /* * restore old Host Master Clock if high_clock is set * and oldclock was not 56KHz */ - if (high_clock && !(oldclock & 0x20)) - sis630_write(SMB_CNT,(sis630_read(SMB_CNT) & ~0x20)); + if (high_clock && !(oldclock & SMBCLK_SEL)) + sis630_write(SMB_CNT, sis630_read(SMB_CNT) & ~SMBCLK_SEL); - dev_dbg(&adap->dev, "SMB_CNT after clock restore 0x%02x\n", sis630_read(SMB_CNT)); + dev_dbg(&adap->dev, + "SMB_CNT after clock restore 0x%02x\n", sis630_read(SMB_CNT)); } static int sis630_transaction(struct i2c_adapter *adap, int size) @@ -229,7 +239,8 @@ static int sis630_transaction(struct i2c_adapter *adap, int size) return result; } -static int sis630_block_data(struct i2c_adapter *adap, union i2c_smbus_data *data, int read_write) +static int sis630_block_data(struct i2c_adapter *adap, + union i2c_smbus_data *data, int read_write) { int i, len = 0, rc = 0; u8 oldclock = 0; @@ -241,39 +252,43 @@ static int sis630_block_data(struct i2c_adapter *adap, union i2c_smbus_data *dat else if (len > 32) len = 32; sis630_write(SMB_COUNT, len); - for (i=1; i <= len; i++) { - dev_dbg(&adap->dev, "set data 0x%02x\n", data->block[i]); + for (i = 1; i <= len; i++) { + dev_dbg(&adap->dev, + "set data 0x%02x\n", data->block[i]); /* set data */ - sis630_write(SMB_BYTE+(i-1)%8, data->block[i]); - if (i==8 || (len<8 && i==len)) { - dev_dbg(&adap->dev, "start trans len=%d i=%d\n",len ,i); + sis630_write(SMB_BYTE + (i - 1) % 8, data->block[i]); + if (i == 8 || (len < 8 && i == len)) { + dev_dbg(&adap->dev, + "start trans len=%d i=%d\n", len, i); /* first transaction */ rc = sis630_transaction_start(adap, SIS630_BLOCK_DATA, &oldclock); if (rc) return rc; - } - else if ((i-1)%8 == 7 || i==len) { - dev_dbg(&adap->dev, "trans_wait len=%d i=%d\n",len,i); - if (i>8) { - dev_dbg(&adap->dev, "clear smbary_sts len=%d i=%d\n",len,i); + } else if ((i - 1) % 8 == 7 || i == len) { + dev_dbg(&adap->dev, + "trans_wait len=%d i=%d\n", len, i); + if (i > 8) { + dev_dbg(&adap->dev, + "clear smbary_sts" + " len=%d i=%d\n", len, i); /* If this is not first transaction, we must clear sticky bit. clear SMBARY_STS */ - sis630_write(SMB_STS,0x10); + sis630_write(SMB_STS, BYTE_DONE_STS); } rc = sis630_transaction_wait(adap, SIS630_BLOCK_DATA); if (rc) { - dev_dbg(&adap->dev, "trans_wait failed\n"); + dev_dbg(&adap->dev, + "trans_wait failed\n"); break; } } } - } - else { + } else { /* read request */ data->block[0] = len = 0; rc = sis630_transaction_start(adap, @@ -294,18 +309,22 @@ static int sis630_block_data(struct i2c_adapter *adap, union i2c_smbus_data *dat if (data->block[0] > 32) data->block[0] = 32; - dev_dbg(&adap->dev, "block data read len=0x%x\n", data->block[0]); + dev_dbg(&adap->dev, + "block data read len=0x%x\n", data->block[0]); - for (i=0; i < 8 && len < data->block[0]; i++,len++) { - dev_dbg(&adap->dev, "read i=%d len=%d\n", i, len); - data->block[len+1] = sis630_read(SMB_BYTE+i); + for (i = 0; i < 8 && len < data->block[0]; i++, len++) { + dev_dbg(&adap->dev, + "read i=%d len=%d\n", i, len); + data->block[len + 1] = sis630_read(SMB_BYTE + + i); } - dev_dbg(&adap->dev, "clear smbary_sts len=%d i=%d\n",len,i); + dev_dbg(&adap->dev, + "clear smbary_sts len=%d i=%d\n", len, i); /* clear SMBARY_STS */ - sis630_write(SMB_STS,0x10); - } while(len < data->block[0]); + sis630_write(SMB_STS, BYTE_DONE_STS); + } while (len < data->block[0]); } sis630_transaction_end(adap, oldclock); @@ -321,42 +340,47 @@ static s32 sis630_access(struct i2c_adapter *adap, u16 addr, int status; switch (size) { - case I2C_SMBUS_QUICK: - sis630_write(SMB_ADDR, ((addr & 0x7f) << 1) | (read_write & 0x01)); - size = SIS630_QUICK; - break; - case I2C_SMBUS_BYTE: - sis630_write(SMB_ADDR, ((addr & 0x7f) << 1) | (read_write & 0x01)); - if (read_write == I2C_SMBUS_WRITE) - sis630_write(SMB_CMD, command); - size = SIS630_BYTE; - break; - case I2C_SMBUS_BYTE_DATA: - sis630_write(SMB_ADDR, ((addr & 0x7f) << 1) | (read_write & 0x01)); - sis630_write(SMB_CMD, command); - if (read_write == I2C_SMBUS_WRITE) - sis630_write(SMB_BYTE, data->byte); - size = SIS630_BYTE_DATA; - break; - case I2C_SMBUS_PROC_CALL: - case I2C_SMBUS_WORD_DATA: - sis630_write(SMB_ADDR,((addr & 0x7f) << 1) | (read_write & 0x01)); + case I2C_SMBUS_QUICK: + sis630_write(SMB_ADDR, + ((addr & 0x7f) << 1) | (read_write & 0x01)); + size = SIS630_QUICK; + break; + case I2C_SMBUS_BYTE: + sis630_write(SMB_ADDR, + ((addr & 0x7f) << 1) | (read_write & 0x01)); + if (read_write == I2C_SMBUS_WRITE) sis630_write(SMB_CMD, command); - if (read_write == I2C_SMBUS_WRITE) { - sis630_write(SMB_BYTE, data->word & 0xff); - sis630_write(SMB_BYTE + 1,(data->word & 0xff00) >> 8); - } - size = (size == I2C_SMBUS_PROC_CALL ? SIS630_PCALL : SIS630_WORD_DATA); - break; - case I2C_SMBUS_BLOCK_DATA: - sis630_write(SMB_ADDR,((addr & 0x7f) << 1) | (read_write & 0x01)); - sis630_write(SMB_CMD, command); - size = SIS630_BLOCK_DATA; - return sis630_block_data(adap, data, read_write); - default: - dev_warn(&adap->dev, "Unsupported transaction %d\n", - size); - return -EOPNOTSUPP; + size = SIS630_BYTE; + break; + case I2C_SMBUS_BYTE_DATA: + sis630_write(SMB_ADDR, + ((addr & 0x7f) << 1) | (read_write & 0x01)); + sis630_write(SMB_CMD, command); + if (read_write == I2C_SMBUS_WRITE) + sis630_write(SMB_BYTE, data->byte); + size = SIS630_BYTE_DATA; + break; + case I2C_SMBUS_PROC_CALL: + case I2C_SMBUS_WORD_DATA: + sis630_write(SMB_ADDR, + ((addr & 0x7f) << 1) | (read_write & 0x01)); + sis630_write(SMB_CMD, command); + if (read_write == I2C_SMBUS_WRITE) { + sis630_write(SMB_BYTE, data->word & 0xff); + sis630_write(SMB_BYTE + 1, (data->word & 0xff00) >> 8); + } + size = (size == I2C_SMBUS_PROC_CALL ? + SIS630_PCALL : SIS630_WORD_DATA); + break; + case I2C_SMBUS_BLOCK_DATA: + sis630_write(SMB_ADDR, + ((addr & 0x7f) << 1) | (read_write & 0x01)); + sis630_write(SMB_CMD, command); + size = SIS630_BLOCK_DATA; + return sis630_block_data(adap, data, read_write); + default: + dev_warn(&adap->dev, "Unsupported transaction %d\n", size); + return -EOPNOTSUPP; } status = sis630_transaction(adap, size); @@ -368,15 +392,16 @@ static s32 sis630_access(struct i2c_adapter *adap, u16 addr, return 0; } - switch(size) { - case SIS630_BYTE: - case SIS630_BYTE_DATA: - data->byte = sis630_read(SMB_BYTE); - break; - case SIS630_PCALL: - case SIS630_WORD_DATA: - data->word = sis630_read(SMB_BYTE) + (sis630_read(SMB_BYTE + 1) << 8); - break; + switch (size) { + case SIS630_BYTE: + case SIS630_BYTE_DATA: + data->byte = sis630_read(SMB_BYTE); + break; + case SIS630_PCALL: + case SIS630_WORD_DATA: + data->word = sis630_read(SMB_BYTE) + + (sis630_read(SMB_BYTE + 1) << 8); + break; } return 0; @@ -384,9 +409,9 @@ static s32 sis630_access(struct i2c_adapter *adap, u16 addr, static u32 sis630_func(struct i2c_adapter *adapter) { - return I2C_FUNC_SMBUS_QUICK | I2C_FUNC_SMBUS_BYTE | I2C_FUNC_SMBUS_BYTE_DATA | - I2C_FUNC_SMBUS_WORD_DATA | I2C_FUNC_SMBUS_PROC_CALL | - I2C_FUNC_SMBUS_BLOCK_DATA; + return I2C_FUNC_SMBUS_QUICK | I2C_FUNC_SMBUS_BYTE | + I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA | + I2C_FUNC_SMBUS_PROC_CALL | I2C_FUNC_SMBUS_BLOCK_DATA; } static int sis630_setup(struct pci_dev *sis630_dev) @@ -394,21 +419,23 @@ static int sis630_setup(struct pci_dev *sis630_dev) unsigned char b; struct pci_dev *dummy = NULL; int retval, i; + /* acpi base address */ + unsigned short acpi_base; /* check for supported SiS devices */ - for (i=0; supported[i] > 0 ; i++) { - if ((dummy = pci_get_device(PCI_VENDOR_ID_SI, supported[i], dummy))) + for (i = 0; supported[i] > 0; i++) { + dummy = pci_get_device(PCI_VENDOR_ID_SI, supported[i], dummy); + if (dummy) break; /* found */ } if (dummy) { pci_dev_put(dummy); - } - else if (force) { - dev_err(&sis630_dev->dev, "WARNING: Can't detect SIS630 compatible device, but " + } else if (force) { + dev_err(&sis630_dev->dev, + "WARNING: Can't detect SIS630 compatible device, but " "loading because of force option enabled\n"); - } - else { + } else { return -ENODEV; } @@ -416,7 +443,7 @@ static int sis630_setup(struct pci_dev *sis630_dev) Enable ACPI first , so we can accsess reg 74-75 in acpi io space and read acpi base addr */ - if (pci_read_config_byte(sis630_dev, SIS630_BIOS_CTL_REG,&b)) { + if (pci_read_config_byte(sis630_dev, SIS630_BIOS_CTL_REG, &b)) { dev_err(&sis630_dev->dev, "Error: Can't read bios ctl reg\n"); retval = -ENODEV; goto exit; @@ -430,24 +457,35 @@ static int sis630_setup(struct pci_dev *sis630_dev) } /* Determine the ACPI base address */ - if (pci_read_config_word(sis630_dev,SIS630_ACPI_BASE_REG,&acpi_base)) { - dev_err(&sis630_dev->dev, "Error: Can't determine ACPI base address\n"); + if (pci_read_config_word(sis630_dev, + SIS630_ACPI_BASE_REG, &acpi_base)) { + dev_err(&sis630_dev->dev, + "Error: Can't determine ACPI base address\n"); retval = -ENODEV; goto exit; } - dev_dbg(&sis630_dev->dev, "ACPI base at 0x%04x\n", acpi_base); + dev_dbg(&sis630_dev->dev, "ACPI base at 0x%04hx\n", acpi_base); + + if (supported[i] == PCI_DEVICE_ID_SI_760) + smbus_base = acpi_base + 0xE0; + else + smbus_base = acpi_base + 0x80; + + dev_dbg(&sis630_dev->dev, "SMBus base at 0x%04hx\n", smbus_base); - retval = acpi_check_region(acpi_base + SMB_STS, SIS630_SMB_IOREGION, + retval = acpi_check_region(smbus_base + SMB_STS, SIS630_SMB_IOREGION, sis630_driver.name); if (retval) goto exit; /* Everything is happy, let's grab the memory and set things up. */ - if (!request_region(acpi_base + SMB_STS, SIS630_SMB_IOREGION, + if (!request_region(smbus_base + SMB_STS, SIS630_SMB_IOREGION, sis630_driver.name)) { - dev_err(&sis630_dev->dev, "SMBus registers 0x%04x-0x%04x already " - "in use!\n", acpi_base + SMB_STS, acpi_base + SMB_SAA); + dev_err(&sis630_dev->dev, + "I/O Region 0x%04hx-0x%04hx for SMBus already in use.\n", + smbus_base + SMB_STS, + smbus_base + SMB_STS + SIS630_SMB_IOREGION - 1); retval = -EBUSY; goto exit; } @@ -456,7 +494,7 @@ static int sis630_setup(struct pci_dev *sis630_dev) exit: if (retval) - acpi_base = 0; + smbus_base = 0; return retval; } @@ -470,20 +508,24 @@ static struct i2c_adapter sis630_adapter = { .owner = THIS_MODULE, .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, + .retries = 3 }; static DEFINE_PCI_DEVICE_TABLE(sis630_ids) = { { PCI_DEVICE(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503) }, { PCI_DEVICE(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC) }, + { PCI_DEVICE(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_964) }, { 0, } }; -MODULE_DEVICE_TABLE (pci, sis630_ids); +MODULE_DEVICE_TABLE(pci, sis630_ids); static int sis630_probe(struct pci_dev *dev, const struct pci_device_id *id) { if (sis630_setup(dev)) { - dev_err(&dev->dev, "SIS630 comp. bus not detected, module not inserted.\n"); + dev_err(&dev->dev, + "SIS630 compatible bus not detected, " + "module not inserted.\n"); return -ENODEV; } @@ -491,17 +533,17 @@ static int sis630_probe(struct pci_dev *dev, const struct pci_device_id *id) sis630_adapter.dev.parent = &dev->dev; snprintf(sis630_adapter.name, sizeof(sis630_adapter.name), - "SMBus SIS630 adapter at %04x", acpi_base + SMB_STS); + "SMBus SIS630 adapter at %04hx", smbus_base + SMB_STS); return i2c_add_adapter(&sis630_adapter); } static void sis630_remove(struct pci_dev *dev) { - if (acpi_base) { + if (smbus_base) { i2c_del_adapter(&sis630_adapter); - release_region(acpi_base + SMB_STS, SIS630_SMB_IOREGION); - acpi_base = 0; + release_region(smbus_base + SMB_STS, SIS630_SMB_IOREGION); + smbus_base = 0; } } |