summaryrefslogtreecommitdiffstats
path: root/drivers/net/de620.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/de620.c')
-rw-r--r--drivers/net/de620.c38
1 files changed, 19 insertions, 19 deletions
diff --git a/drivers/net/de620.c b/drivers/net/de620.c
index 22fc5b869a60..a18d4d14b665 100644
--- a/drivers/net/de620.c
+++ b/drivers/net/de620.c
@@ -40,7 +40,7 @@
*****************************************************************************/
static const char version[] =
"de620.c: $Revision: 1.40 $, Bjorn Ekwall <bj0rn@blox.se>\n";
-
+
/***********************************************************************
*
* "Tuning" section.
@@ -115,7 +115,7 @@ static const char version[] =
#define COUNT_LOOPS
*/
#endif
-
+
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/types.h>
@@ -250,7 +250,7 @@ static struct nic {
byte Media;
byte SCR;
} nic_data;
-
+
/**********************************************************
* *
* Convenience macros/functions for D-Link DE-620 adapter *
@@ -432,7 +432,7 @@ de620_get_register(struct net_device *dev, byte reg)
return value;
}
-
+
/*********************************************************************
*
* Open/initialize the board.
@@ -515,10 +515,10 @@ static void de620_set_multicast_list(struct net_device *dev)
}
/*******************************************************
- *
+ *
* Handle timeouts on transmit
*/
-
+
static void de620_timeout(struct net_device *dev)
{
printk(KERN_WARNING "%s: transmit timed out, %s?\n", dev->name, "network cable problem");
@@ -540,9 +540,9 @@ static int de620_start_xmit(struct sk_buff *skb, struct net_device *dev)
byte using_txbuf;
using_txbuf = de620_tx_buffs(dev); /* Peek at the adapter */
-
+
netif_stop_queue(dev);
-
+
if ((len = skb->len) < RUNT)
len = RUNT;
@@ -584,7 +584,7 @@ static int de620_start_xmit(struct sk_buff *skb, struct net_device *dev)
dev_kfree_skb (skb);
return 0;
}
-
+
/*****************************************************
*
* Handle the network interface interrupts.
@@ -599,7 +599,7 @@ de620_interrupt(int irq_in, void *dev_id, struct pt_regs *regs)
int again = 0;
spin_lock(&de620_lock);
-
+
/* Read the status register (_not_ the status port) */
irq_status = de620_get_register(dev, R_STS);
@@ -615,7 +615,7 @@ de620_interrupt(int irq_in, void *dev_id, struct pt_regs *regs)
if(de620_tx_buffs(dev) != (TXBF0 | TXBF1))
netif_wake_queue(dev);
-
+
spin_unlock(&de620_lock);
return IRQ_HANDLED;
}
@@ -720,7 +720,7 @@ static int de620_rx_intr(struct net_device *dev)
return (next_rx_page != curr_page); /* That was slightly tricky... */
}
-
+
/*********************************************
*
* Reset the adapter to a known state
@@ -803,7 +803,7 @@ static int adapter_init(struct net_device *dev)
return 0; /* all ok */
}
-
+
/******************************************************************************
*
* Only start-up code below
@@ -827,7 +827,7 @@ struct net_device * __init de620_probe(int unit)
SET_MODULE_OWNER(dev);
spin_lock_init(&de620_lock);
-
+
/*
* This is where the base_addr and irq gets set.
* Tunable at compile-time and insmod-time
@@ -840,7 +840,7 @@ struct net_device * __init de620_probe(int unit)
sprintf(dev->name, "eth%d", unit);
netdev_boot_setup_check(dev);
}
-
+
if (de620_debug)
printk(version);
@@ -889,7 +889,7 @@ struct net_device * __init de620_probe(int unit)
dev->tx_timeout = de620_timeout;
dev->watchdog_timeo = HZ*2;
dev->set_multicast_list = de620_set_multicast_list;
-
+
/* base_addr and irq are already set, see above! */
/* dump eeprom */
@@ -917,7 +917,7 @@ out1:
out:
return ERR_PTR(err);
}
-
+
/**********************************
*
* Read info from on-board EEPROM
@@ -1003,7 +1003,7 @@ static int __init read_eeprom(struct net_device *dev)
return 0; /* no errors */
}
-
+
/******************************************************************************
*
* Loadable module skeleton
@@ -1029,7 +1029,7 @@ void cleanup_module(void)
#endif /* MODULE */
MODULE_LICENSE("GPL");
-
+
/*
* (add '-DMODULE' when compiling as loadable module)
*