summaryrefslogtreecommitdiffstats
path: root/drivers/net/e1000e/lib.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/e1000e/lib.c')
-rw-r--r--drivers/net/e1000e/lib.c65
1 files changed, 31 insertions, 34 deletions
diff --git a/drivers/net/e1000e/lib.c b/drivers/net/e1000e/lib.c
index 9c3ce719e8da..ea3ff6369c86 100644
--- a/drivers/net/e1000e/lib.c
+++ b/drivers/net/e1000e/lib.c
@@ -603,7 +603,6 @@ s32 e1000e_check_for_serdes_link(struct e1000_hw *hw)
**/
static s32 e1000_set_default_fc_generic(struct e1000_hw *hw)
{
- struct e1000_mac_info *mac = &hw->mac;
s32 ret_val;
u16 nvm_data;
@@ -624,12 +623,12 @@ static s32 e1000_set_default_fc_generic(struct e1000_hw *hw)
}
if ((nvm_data & NVM_WORD0F_PAUSE_MASK) == 0)
- mac->fc = e1000_fc_none;
+ hw->fc.type = e1000_fc_none;
else if ((nvm_data & NVM_WORD0F_PAUSE_MASK) ==
NVM_WORD0F_ASM_DIR)
- mac->fc = e1000_fc_tx_pause;
+ hw->fc.type = e1000_fc_tx_pause;
else
- mac->fc = e1000_fc_full;
+ hw->fc.type = e1000_fc_full;
return 0;
}
@@ -660,7 +659,7 @@ s32 e1000e_setup_link(struct e1000_hw *hw)
* If flow control is set to default, set flow control based on
* the EEPROM flow control settings.
*/
- if (mac->fc == e1000_fc_default) {
+ if (hw->fc.type == e1000_fc_default) {
ret_val = e1000_set_default_fc_generic(hw);
if (ret_val)
return ret_val;
@@ -671,9 +670,9 @@ s32 e1000e_setup_link(struct e1000_hw *hw)
* in case we get disconnected and then reconnected into a different
* hub or switch with different Flow Control capabilities.
*/
- mac->original_fc = mac->fc;
+ hw->fc.original_type = hw->fc.type;
- hw_dbg(hw, "After fix-ups FlowControl is now = %x\n", mac->fc);
+ hw_dbg(hw, "After fix-ups FlowControl is now = %x\n", hw->fc.type);
/* Call the necessary media_type subroutine to configure the link. */
ret_val = mac->ops.setup_physical_interface(hw);
@@ -691,7 +690,7 @@ s32 e1000e_setup_link(struct e1000_hw *hw)
ew32(FCAH, FLOW_CONTROL_ADDRESS_HIGH);
ew32(FCAL, FLOW_CONTROL_ADDRESS_LOW);
- ew32(FCTTV, mac->fc_pause_time);
+ ew32(FCTTV, hw->fc.pause_time);
return e1000e_set_fc_watermarks(hw);
}
@@ -725,7 +724,7 @@ static s32 e1000_commit_fc_settings_generic(struct e1000_hw *hw)
* do not support receiving pause frames).
* 3: Both Rx and Tx flow control (symmetric) are enabled.
*/
- switch (mac->fc) {
+ switch (hw->fc.type) {
case e1000_fc_none:
/* Flow control completely disabled by a software over-ride. */
txcw = (E1000_TXCW_ANE | E1000_TXCW_FD);
@@ -857,7 +856,7 @@ s32 e1000e_setup_fiber_serdes_link(struct e1000_hw *hw)
* detect a signal. If we have a signal, then poll for a "Link-Up"
* indication.
*/
- if (hw->media_type == e1000_media_type_internal_serdes ||
+ if (hw->phy.media_type == e1000_media_type_internal_serdes ||
(er32(CTRL) & E1000_CTRL_SWDPIN1)) {
ret_val = e1000_poll_fiber_serdes_link_generic(hw);
} else {
@@ -898,7 +897,6 @@ void e1000e_config_collision_dist(struct e1000_hw *hw)
**/
s32 e1000e_set_fc_watermarks(struct e1000_hw *hw)
{
- struct e1000_mac_info *mac = &hw->mac;
u32 fcrtl = 0, fcrth = 0;
/*
@@ -908,15 +906,15 @@ s32 e1000e_set_fc_watermarks(struct e1000_hw *hw)
* ability to transmit pause frames is not enabled, then these
* registers will be set to 0.
*/
- if (mac->fc & e1000_fc_tx_pause) {
+ if (hw->fc.type & e1000_fc_tx_pause) {
/*
* We need to set up the Receive Threshold high and low water
* marks as well as (optionally) enabling the transmission of
* XON frames.
*/
- fcrtl = mac->fc_low_water;
+ fcrtl = hw->fc.low_water;
fcrtl |= E1000_FCRTL_XONE;
- fcrth = mac->fc_high_water;
+ fcrth = hw->fc.high_water;
}
ew32(FCRTL, fcrtl);
ew32(FCRTH, fcrth);
@@ -936,7 +934,6 @@ s32 e1000e_set_fc_watermarks(struct e1000_hw *hw)
**/
s32 e1000e_force_mac_fc(struct e1000_hw *hw)
{
- struct e1000_mac_info *mac = &hw->mac;
u32 ctrl;
ctrl = er32(CTRL);
@@ -948,7 +945,7 @@ s32 e1000e_force_mac_fc(struct e1000_hw *hw)
* receive flow control.
*
* The "Case" statement below enables/disable flow control
- * according to the "mac->fc" parameter.
+ * according to the "hw->fc.type" parameter.
*
* The possible values of the "fc" parameter are:
* 0: Flow control is completely disabled
@@ -959,9 +956,9 @@ s32 e1000e_force_mac_fc(struct e1000_hw *hw)
* 3: Both Rx and Tx flow control (symmetric) is enabled.
* other: No other values should be possible at this point.
*/
- hw_dbg(hw, "mac->fc = %u\n", mac->fc);
+ hw_dbg(hw, "hw->fc.type = %u\n", hw->fc.type);
- switch (mac->fc) {
+ switch (hw->fc.type) {
case e1000_fc_none:
ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
break;
@@ -1009,11 +1006,11 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
* configuration of the MAC to match the "fc" parameter.
*/
if (mac->autoneg_failed) {
- if (hw->media_type == e1000_media_type_fiber ||
- hw->media_type == e1000_media_type_internal_serdes)
+ if (hw->phy.media_type == e1000_media_type_fiber ||
+ hw->phy.media_type == e1000_media_type_internal_serdes)
ret_val = e1000e_force_mac_fc(hw);
} else {
- if (hw->media_type == e1000_media_type_copper)
+ if (hw->phy.media_type == e1000_media_type_copper)
ret_val = e1000e_force_mac_fc(hw);
}
@@ -1028,7 +1025,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
* has completed, and if so, how the PHY and link partner has
* flow control configured.
*/
- if ((hw->media_type == e1000_media_type_copper) && mac->autoneg) {
+ if ((hw->phy.media_type == e1000_media_type_copper) && mac->autoneg) {
/*
* Read the MII Status Register and check to see if AutoNeg
* has completed. We read this twice because this reg has
@@ -1105,11 +1102,11 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
* ONLY. Hence, we must now check to see if we need to
* turn OFF the TRANSMISSION of PAUSE frames.
*/
- if (mac->original_fc == e1000_fc_full) {
- mac->fc = e1000_fc_full;
+ if (hw->fc.original_type == e1000_fc_full) {
+ hw->fc.type = e1000_fc_full;
hw_dbg(hw, "Flow Control = FULL.\r\n");
} else {
- mac->fc = e1000_fc_rx_pause;
+ hw->fc.type = e1000_fc_rx_pause;
hw_dbg(hw, "Flow Control = "
"RX PAUSE frames only.\r\n");
}
@@ -1127,8 +1124,8 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
(mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
(mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
- mac->fc = e1000_fc_tx_pause;
- hw_dbg(hw, "Flow Control = TX PAUSE frames only.\r\n");
+ hw->fc.type = e1000_fc_tx_pause;
+ hw_dbg(hw, "Flow Control = Tx PAUSE frames only.\r\n");
}
/*
* For transmitting PAUSE frames ONLY.
@@ -1143,14 +1140,14 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
(mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
!(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
(mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
- mac->fc = e1000_fc_rx_pause;
- hw_dbg(hw, "Flow Control = RX PAUSE frames only.\r\n");
+ hw->fc.type = e1000_fc_rx_pause;
+ hw_dbg(hw, "Flow Control = Rx PAUSE frames only.\r\n");
} else {
/*
* Per the IEEE spec, at this point flow control
* should be disabled.
*/
- mac->fc = e1000_fc_none;
+ hw->fc.type = e1000_fc_none;
hw_dbg(hw, "Flow Control = NONE.\r\n");
}
@@ -1166,7 +1163,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
}
if (duplex == HALF_DUPLEX)
- mac->fc = e1000_fc_none;
+ hw->fc.type = e1000_fc_none;
/*
* Now we call a subroutine to actually force the MAC
@@ -1436,7 +1433,7 @@ s32 e1000e_blink_led(struct e1000_hw *hw)
u32 ledctl_blink = 0;
u32 i;
- if (hw->media_type == e1000_media_type_fiber) {
+ if (hw->phy.media_type == e1000_media_type_fiber) {
/* always blink LED0 for PCI-E fiber */
ledctl_blink = E1000_LEDCTL_LED0_BLINK |
(E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT);
@@ -1468,7 +1465,7 @@ s32 e1000e_led_on_generic(struct e1000_hw *hw)
{
u32 ctrl;
- switch (hw->media_type) {
+ switch (hw->phy.media_type) {
case e1000_media_type_fiber:
ctrl = er32(CTRL);
ctrl &= ~E1000_CTRL_SWDPIN0;
@@ -1495,7 +1492,7 @@ s32 e1000e_led_off_generic(struct e1000_hw *hw)
{
u32 ctrl;
- switch (hw->media_type) {
+ switch (hw->phy.media_type) {
case e1000_media_type_fiber:
ctrl = er32(CTRL);
ctrl |= E1000_CTRL_SWDPIN0;