diff options
Diffstat (limited to 'include/linux/platform_data')
27 files changed, 986 insertions, 77 deletions
diff --git a/include/linux/platform_data/adp5588.h b/include/linux/platform_data/adp5588.h new file mode 100644 index 000000000000..c2153049cfbd --- /dev/null +++ b/include/linux/platform_data/adp5588.h @@ -0,0 +1,172 @@ +/* + * Analog Devices ADP5588 I/O Expander and QWERTY Keypad Controller + * + * Copyright 2009-2010 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#ifndef _ADP5588_H +#define _ADP5588_H + +#define DEV_ID 0x00 /* Device ID */ +#define CFG 0x01 /* Configuration Register1 */ +#define INT_STAT 0x02 /* Interrupt Status Register */ +#define KEY_LCK_EC_STAT 0x03 /* Key Lock and Event Counter Register */ +#define Key_EVENTA 0x04 /* Key Event Register A */ +#define Key_EVENTB 0x05 /* Key Event Register B */ +#define Key_EVENTC 0x06 /* Key Event Register C */ +#define Key_EVENTD 0x07 /* Key Event Register D */ +#define Key_EVENTE 0x08 /* Key Event Register E */ +#define Key_EVENTF 0x09 /* Key Event Register F */ +#define Key_EVENTG 0x0A /* Key Event Register G */ +#define Key_EVENTH 0x0B /* Key Event Register H */ +#define Key_EVENTI 0x0C /* Key Event Register I */ +#define Key_EVENTJ 0x0D /* Key Event Register J */ +#define KP_LCK_TMR 0x0E /* Keypad Lock1 to Lock2 Timer */ +#define UNLOCK1 0x0F /* Unlock Key1 */ +#define UNLOCK2 0x10 /* Unlock Key2 */ +#define GPIO_INT_STAT1 0x11 /* GPIO Interrupt Status */ +#define GPIO_INT_STAT2 0x12 /* GPIO Interrupt Status */ +#define GPIO_INT_STAT3 0x13 /* GPIO Interrupt Status */ +#define GPIO_DAT_STAT1 0x14 /* GPIO Data Status, Read twice to clear */ +#define GPIO_DAT_STAT2 0x15 /* GPIO Data Status, Read twice to clear */ +#define GPIO_DAT_STAT3 0x16 /* GPIO Data Status, Read twice to clear */ +#define GPIO_DAT_OUT1 0x17 /* GPIO DATA OUT */ +#define GPIO_DAT_OUT2 0x18 /* GPIO DATA OUT */ +#define GPIO_DAT_OUT3 0x19 /* GPIO DATA OUT */ +#define GPIO_INT_EN1 0x1A /* GPIO Interrupt Enable */ +#define GPIO_INT_EN2 0x1B /* GPIO Interrupt Enable */ +#define GPIO_INT_EN3 0x1C /* GPIO Interrupt Enable */ +#define KP_GPIO1 0x1D /* Keypad or GPIO Selection */ +#define KP_GPIO2 0x1E /* Keypad or GPIO Selection */ +#define KP_GPIO3 0x1F /* Keypad or GPIO Selection */ +#define GPI_EM1 0x20 /* GPI Event Mode 1 */ +#define GPI_EM2 0x21 /* GPI Event Mode 2 */ +#define GPI_EM3 0x22 /* GPI Event Mode 3 */ +#define GPIO_DIR1 0x23 /* GPIO Data Direction */ +#define GPIO_DIR2 0x24 /* GPIO Data Direction */ +#define GPIO_DIR3 0x25 /* GPIO Data Direction */ +#define GPIO_INT_LVL1 0x26 /* GPIO Edge/Level Detect */ +#define GPIO_INT_LVL2 0x27 /* GPIO Edge/Level Detect */ +#define GPIO_INT_LVL3 0x28 /* GPIO Edge/Level Detect */ +#define Debounce_DIS1 0x29 /* Debounce Disable */ +#define Debounce_DIS2 0x2A /* Debounce Disable */ +#define Debounce_DIS3 0x2B /* Debounce Disable */ +#define GPIO_PULL1 0x2C /* GPIO Pull Disable */ +#define GPIO_PULL2 0x2D /* GPIO Pull Disable */ +#define GPIO_PULL3 0x2E /* GPIO Pull Disable */ +#define CMP_CFG_STAT 0x30 /* Comparator Configuration and Status Register */ +#define CMP_CONFG_SENS1 0x31 /* Sensor1 Comparator Configuration Register */ +#define CMP_CONFG_SENS2 0x32 /* L2 Light Sensor Reference Level, Output Falling for Sensor 1 */ +#define CMP1_LVL2_TRIP 0x33 /* L2 Light Sensor Hysteresis (Active when Output Rising) for Sensor 1 */ +#define CMP1_LVL2_HYS 0x34 /* L3 Light Sensor Reference Level, Output Falling For Sensor 1 */ +#define CMP1_LVL3_TRIP 0x35 /* L3 Light Sensor Hysteresis (Active when Output Rising) For Sensor 1 */ +#define CMP1_LVL3_HYS 0x36 /* Sensor 2 Comparator Configuration Register */ +#define CMP2_LVL2_TRIP 0x37 /* L2 Light Sensor Reference Level, Output Falling for Sensor 2 */ +#define CMP2_LVL2_HYS 0x38 /* L2 Light Sensor Hysteresis (Active when Output Rising) for Sensor 2 */ +#define CMP2_LVL3_TRIP 0x39 /* L3 Light Sensor Reference Level, Output Falling For Sensor 2 */ +#define CMP2_LVL3_HYS 0x3A /* L3 Light Sensor Hysteresis (Active when Output Rising) For Sensor 2 */ +#define CMP1_ADC_DAT_R1 0x3B /* Comparator 1 ADC data Register1 */ +#define CMP1_ADC_DAT_R2 0x3C /* Comparator 1 ADC data Register2 */ +#define CMP2_ADC_DAT_R1 0x3D /* Comparator 2 ADC data Register1 */ +#define CMP2_ADC_DAT_R2 0x3E /* Comparator 2 ADC data Register2 */ + +#define ADP5588_DEVICE_ID_MASK 0xF + + /* Configuration Register1 */ +#define ADP5588_AUTO_INC (1 << 7) +#define ADP5588_GPIEM_CFG (1 << 6) +#define ADP5588_OVR_FLOW_M (1 << 5) +#define ADP5588_INT_CFG (1 << 4) +#define ADP5588_OVR_FLOW_IEN (1 << 3) +#define ADP5588_K_LCK_IM (1 << 2) +#define ADP5588_GPI_IEN (1 << 1) +#define ADP5588_KE_IEN (1 << 0) + +/* Interrupt Status Register */ +#define ADP5588_CMP2_INT (1 << 5) +#define ADP5588_CMP1_INT (1 << 4) +#define ADP5588_OVR_FLOW_INT (1 << 3) +#define ADP5588_K_LCK_INT (1 << 2) +#define ADP5588_GPI_INT (1 << 1) +#define ADP5588_KE_INT (1 << 0) + +/* Key Lock and Event Counter Register */ +#define ADP5588_K_LCK_EN (1 << 6) +#define ADP5588_LCK21 0x30 +#define ADP5588_KEC 0xF + +#define ADP5588_MAXGPIO 18 +#define ADP5588_BANK(offs) ((offs) >> 3) +#define ADP5588_BIT(offs) (1u << ((offs) & 0x7)) + +/* Put one of these structures in i2c_board_info platform_data */ + +#define ADP5588_KEYMAPSIZE 80 + +#define GPI_PIN_ROW0 97 +#define GPI_PIN_ROW1 98 +#define GPI_PIN_ROW2 99 +#define GPI_PIN_ROW3 100 +#define GPI_PIN_ROW4 101 +#define GPI_PIN_ROW5 102 +#define GPI_PIN_ROW6 103 +#define GPI_PIN_ROW7 104 +#define GPI_PIN_COL0 105 +#define GPI_PIN_COL1 106 +#define GPI_PIN_COL2 107 +#define GPI_PIN_COL3 108 +#define GPI_PIN_COL4 109 +#define GPI_PIN_COL5 110 +#define GPI_PIN_COL6 111 +#define GPI_PIN_COL7 112 +#define GPI_PIN_COL8 113 +#define GPI_PIN_COL9 114 + +#define GPI_PIN_ROW_BASE GPI_PIN_ROW0 +#define GPI_PIN_ROW_END GPI_PIN_ROW7 +#define GPI_PIN_COL_BASE GPI_PIN_COL0 +#define GPI_PIN_COL_END GPI_PIN_COL9 + +#define GPI_PIN_BASE GPI_PIN_ROW_BASE +#define GPI_PIN_END GPI_PIN_COL_END + +#define ADP5588_GPIMAPSIZE_MAX (GPI_PIN_END - GPI_PIN_BASE + 1) + +struct adp5588_gpi_map { + unsigned short pin; + unsigned short sw_evt; +}; + +struct adp5588_kpad_platform_data { + int rows; /* Number of rows */ + int cols; /* Number of columns */ + const unsigned short *keymap; /* Pointer to keymap */ + unsigned short keymapsize; /* Keymap size */ + unsigned repeat:1; /* Enable key repeat */ + unsigned en_keylock:1; /* Enable Key Lock feature */ + unsigned short unlock_key1; /* Unlock Key 1 */ + unsigned short unlock_key2; /* Unlock Key 2 */ + const struct adp5588_gpi_map *gpimap; + unsigned short gpimapsize; + const struct adp5588_gpio_platform_data *gpio_data; +}; + +struct i2c_client; /* forward declaration */ + +struct adp5588_gpio_platform_data { + int gpio_start; /* GPIO Chip base # */ + const char *const *names; + unsigned irq_base; /* interrupt base # */ + unsigned pullup_dis_mask; /* Pull-Up Disable Mask */ + int (*setup)(struct i2c_client *client, + unsigned gpio, unsigned ngpio, + void *context); + int (*teardown)(struct i2c_client *client, + unsigned gpio, unsigned ngpio, + void *context); + void *context; +}; + +#endif diff --git a/include/linux/platform_data/adp8860.h b/include/linux/platform_data/adp8860.h new file mode 100644 index 000000000000..0b4d39855c91 --- /dev/null +++ b/include/linux/platform_data/adp8860.h @@ -0,0 +1,154 @@ +/* + * Definitions and platform data for Analog Devices + * Backlight drivers ADP8860 + * + * Copyright 2009-2010 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#ifndef __LINUX_I2C_ADP8860_H +#define __LINUX_I2C_ADP8860_H + +#include <linux/leds.h> +#include <linux/types.h> + +#define ID_ADP8860 8860 + +#define ADP8860_MAX_BRIGHTNESS 0x7F +#define FLAG_OFFT_SHIFT 8 + +/* + * LEDs subdevice platform data + */ + +#define ADP8860_LED_DIS_BLINK (0 << FLAG_OFFT_SHIFT) +#define ADP8860_LED_OFFT_600ms (1 << FLAG_OFFT_SHIFT) +#define ADP8860_LED_OFFT_1200ms (2 << FLAG_OFFT_SHIFT) +#define ADP8860_LED_OFFT_1800ms (3 << FLAG_OFFT_SHIFT) + +#define ADP8860_LED_ONT_200ms 0 +#define ADP8860_LED_ONT_600ms 1 +#define ADP8860_LED_ONT_800ms 2 +#define ADP8860_LED_ONT_1200ms 3 + +#define ADP8860_LED_D7 (7) +#define ADP8860_LED_D6 (6) +#define ADP8860_LED_D5 (5) +#define ADP8860_LED_D4 (4) +#define ADP8860_LED_D3 (3) +#define ADP8860_LED_D2 (2) +#define ADP8860_LED_D1 (1) + +/* + * Backlight subdevice platform data + */ + +#define ADP8860_BL_D7 (1 << 6) +#define ADP8860_BL_D6 (1 << 5) +#define ADP8860_BL_D5 (1 << 4) +#define ADP8860_BL_D4 (1 << 3) +#define ADP8860_BL_D3 (1 << 2) +#define ADP8860_BL_D2 (1 << 1) +#define ADP8860_BL_D1 (1 << 0) + +#define ADP8860_FADE_T_DIS 0 /* Fade Timer Disabled */ +#define ADP8860_FADE_T_300ms 1 /* 0.3 Sec */ +#define ADP8860_FADE_T_600ms 2 +#define ADP8860_FADE_T_900ms 3 +#define ADP8860_FADE_T_1200ms 4 +#define ADP8860_FADE_T_1500ms 5 +#define ADP8860_FADE_T_1800ms 6 +#define ADP8860_FADE_T_2100ms 7 +#define ADP8860_FADE_T_2400ms 8 +#define ADP8860_FADE_T_2700ms 9 +#define ADP8860_FADE_T_3000ms 10 +#define ADP8860_FADE_T_3500ms 11 +#define ADP8860_FADE_T_4000ms 12 +#define ADP8860_FADE_T_4500ms 13 +#define ADP8860_FADE_T_5000ms 14 +#define ADP8860_FADE_T_5500ms 15 /* 5.5 Sec */ + +#define ADP8860_FADE_LAW_LINEAR 0 +#define ADP8860_FADE_LAW_SQUARE 1 +#define ADP8860_FADE_LAW_CUBIC1 2 +#define ADP8860_FADE_LAW_CUBIC2 3 + +#define ADP8860_BL_AMBL_FILT_80ms 0 /* Light sensor filter time */ +#define ADP8860_BL_AMBL_FILT_160ms 1 +#define ADP8860_BL_AMBL_FILT_320ms 2 +#define ADP8860_BL_AMBL_FILT_640ms 3 +#define ADP8860_BL_AMBL_FILT_1280ms 4 +#define ADP8860_BL_AMBL_FILT_2560ms 5 +#define ADP8860_BL_AMBL_FILT_5120ms 6 +#define ADP8860_BL_AMBL_FILT_10240ms 7 /* 10.24 sec */ + +/* + * Blacklight current 0..30mA + */ +#define ADP8860_BL_CUR_mA(I) ((I * 127) / 30) + +/* + * L2 comparator current 0..1106uA + */ +#define ADP8860_L2_COMP_CURR_uA(I) ((I * 255) / 1106) + +/* + * L3 comparator current 0..138uA + */ +#define ADP8860_L3_COMP_CURR_uA(I) ((I * 255) / 138) + +struct adp8860_backlight_platform_data { + u8 bl_led_assign; /* 1 = Backlight 0 = Individual LED */ + + u8 bl_fade_in; /* Backlight Fade-In Timer */ + u8 bl_fade_out; /* Backlight Fade-Out Timer */ + u8 bl_fade_law; /* fade-on/fade-off transfer characteristic */ + + u8 en_ambl_sens; /* 1 = enable ambient light sensor */ + u8 abml_filt; /* Light sensor filter time */ + + u8 l1_daylight_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */ + u8 l1_daylight_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */ + u8 l2_office_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */ + u8 l2_office_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */ + u8 l3_dark_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */ + u8 l3_dark_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */ + + u8 l2_trip; /* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */ + u8 l2_hyst; /* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */ + u8 l3_trip; /* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */ + u8 l3_hyst; /* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */ + + /** + * Independent Current Sinks / LEDS + * Sinks not assigned to the Backlight can be exposed to + * user space using the LEDS CLASS interface + */ + + int num_leds; + struct led_info *leds; + u8 led_fade_in; /* LED Fade-In Timer */ + u8 led_fade_out; /* LED Fade-Out Timer */ + u8 led_fade_law; /* fade-on/fade-off transfer characteristic */ + u8 led_on_time; + + /** + * Gain down disable. Setting this option does not allow the + * charge pump to switch to lower gains. NOT AVAILABLE on ADP8860 + * 1 = the charge pump doesn't switch down in gain until all LEDs are 0. + * The charge pump switches up in gain as needed. This feature is + * useful if the ADP8863 charge pump is used to drive an external load. + * This feature must be used when utilizing small fly capacitors + * (0402 or smaller). + * 0 = the charge pump automatically switches up and down in gain. + * This provides optimal efficiency, but is not suitable for driving + * loads that are not connected through the ADP8863 diode drivers. + * Additionally, the charge pump fly capacitors should be low ESR + * and sized 0603 or greater. + */ + + u8 gdwn_dis; +}; + +#endif /* __LINUX_I2C_ADP8860_H */ diff --git a/include/linux/platform_data/adp8870.h b/include/linux/platform_data/adp8870.h new file mode 100644 index 000000000000..624dceccbd5b --- /dev/null +++ b/include/linux/platform_data/adp8870.h @@ -0,0 +1,153 @@ +/* + * Definitions and platform data for Analog Devices + * Backlight drivers ADP8870 + * + * Copyright 2009-2010 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#ifndef __LINUX_I2C_ADP8870_H +#define __LINUX_I2C_ADP8870_H + +#define ID_ADP8870 8870 + +#define ADP8870_MAX_BRIGHTNESS 0x7F +#define FLAG_OFFT_SHIFT 8 + +/* + * LEDs subdevice platform data + */ + +#define ADP8870_LED_DIS_BLINK (0 << FLAG_OFFT_SHIFT) +#define ADP8870_LED_OFFT_600ms (1 << FLAG_OFFT_SHIFT) +#define ADP8870_LED_OFFT_1200ms (2 << FLAG_OFFT_SHIFT) +#define ADP8870_LED_OFFT_1800ms (3 << FLAG_OFFT_SHIFT) + +#define ADP8870_LED_ONT_200ms 0 +#define ADP8870_LED_ONT_600ms 1 +#define ADP8870_LED_ONT_800ms 2 +#define ADP8870_LED_ONT_1200ms 3 + +#define ADP8870_LED_D7 (7) +#define ADP8870_LED_D6 (6) +#define ADP8870_LED_D5 (5) +#define ADP8870_LED_D4 (4) +#define ADP8870_LED_D3 (3) +#define ADP8870_LED_D2 (2) +#define ADP8870_LED_D1 (1) + +/* + * Backlight subdevice platform data + */ + +#define ADP8870_BL_D7 (1 << 6) +#define ADP8870_BL_D6 (1 << 5) +#define ADP8870_BL_D5 (1 << 4) +#define ADP8870_BL_D4 (1 << 3) +#define ADP8870_BL_D3 (1 << 2) +#define ADP8870_BL_D2 (1 << 1) +#define ADP8870_BL_D1 (1 << 0) + +#define ADP8870_FADE_T_DIS 0 /* Fade Timer Disabled */ +#define ADP8870_FADE_T_300ms 1 /* 0.3 Sec */ +#define ADP8870_FADE_T_600ms 2 +#define ADP8870_FADE_T_900ms 3 +#define ADP8870_FADE_T_1200ms 4 +#define ADP8870_FADE_T_1500ms 5 +#define ADP8870_FADE_T_1800ms 6 +#define ADP8870_FADE_T_2100ms 7 +#define ADP8870_FADE_T_2400ms 8 +#define ADP8870_FADE_T_2700ms 9 +#define ADP8870_FADE_T_3000ms 10 +#define ADP8870_FADE_T_3500ms 11 +#define ADP8870_FADE_T_4000ms 12 +#define ADP8870_FADE_T_4500ms 13 +#define ADP8870_FADE_T_5000ms 14 +#define ADP8870_FADE_T_5500ms 15 /* 5.5 Sec */ + +#define ADP8870_FADE_LAW_LINEAR 0 +#define ADP8870_FADE_LAW_SQUARE 1 +#define ADP8870_FADE_LAW_CUBIC1 2 +#define ADP8870_FADE_LAW_CUBIC2 3 + +#define ADP8870_BL_AMBL_FILT_80ms 0 /* Light sensor filter time */ +#define ADP8870_BL_AMBL_FILT_160ms 1 +#define ADP8870_BL_AMBL_FILT_320ms 2 +#define ADP8870_BL_AMBL_FILT_640ms 3 +#define ADP8870_BL_AMBL_FILT_1280ms 4 +#define ADP8870_BL_AMBL_FILT_2560ms 5 +#define ADP8870_BL_AMBL_FILT_5120ms 6 +#define ADP8870_BL_AMBL_FILT_10240ms 7 /* 10.24 sec */ + +/* + * Blacklight current 0..30mA + */ +#define ADP8870_BL_CUR_mA(I) ((I * 127) / 30) + +/* + * L2 comparator current 0..1106uA + */ +#define ADP8870_L2_COMP_CURR_uA(I) ((I * 255) / 1106) + +/* + * L3 comparator current 0..551uA + */ +#define ADP8870_L3_COMP_CURR_uA(I) ((I * 255) / 551) + +/* + * L4 comparator current 0..275uA + */ +#define ADP8870_L4_COMP_CURR_uA(I) ((I * 255) / 275) + +/* + * L5 comparator current 0..138uA + */ +#define ADP8870_L5_COMP_CURR_uA(I) ((I * 255) / 138) + +struct adp8870_backlight_platform_data { + u8 bl_led_assign; /* 1 = Backlight 0 = Individual LED */ + u8 pwm_assign; /* 1 = Enables PWM mode */ + + u8 bl_fade_in; /* Backlight Fade-In Timer */ + u8 bl_fade_out; /* Backlight Fade-Out Timer */ + u8 bl_fade_law; /* fade-on/fade-off transfer characteristic */ + + u8 en_ambl_sens; /* 1 = enable ambient light sensor */ + u8 abml_filt; /* Light sensor filter time */ + + u8 l1_daylight_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */ + u8 l1_daylight_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */ + u8 l2_bright_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */ + u8 l2_bright_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */ + u8 l3_office_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */ + u8 l3_office_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */ + u8 l4_indoor_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */ + u8 l4_indor_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */ + u8 l5_dark_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */ + u8 l5_dark_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */ + + u8 l2_trip; /* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */ + u8 l2_hyst; /* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */ + u8 l3_trip; /* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */ + u8 l3_hyst; /* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */ + u8 l4_trip; /* use L4_COMP_CURR_uA(I) 0 <= I <= 275 uA */ + u8 l4_hyst; /* use L4_COMP_CURR_uA(I) 0 <= I <= 275 uA */ + u8 l5_trip; /* use L5_COMP_CURR_uA(I) 0 <= I <= 138 uA */ + u8 l5_hyst; /* use L6_COMP_CURR_uA(I) 0 <= I <= 138 uA */ + + /** + * Independent Current Sinks / LEDS + * Sinks not assigned to the Backlight can be exposed to + * user space using the LEDS CLASS interface + */ + + int num_leds; + struct led_info *leds; + u8 led_fade_in; /* LED Fade-In Timer */ + u8 led_fade_out; /* LED Fade-Out Timer */ + u8 led_fade_law; /* fade-on/fade-off transfer characteristic */ + u8 led_on_time; +}; + +#endif /* __LINUX_I2C_ADP8870_H */ diff --git a/include/linux/platform_data/ads1015.h b/include/linux/platform_data/ads1015.h new file mode 100644 index 000000000000..d5aa2a045669 --- /dev/null +++ b/include/linux/platform_data/ads1015.h @@ -0,0 +1,36 @@ +/* + * Platform Data for ADS1015 12-bit 4-input ADC + * (C) Copyright 2010 + * Dirk Eibach, Guntermann & Drunck GmbH <eibach@gdsys.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef LINUX_ADS1015_H +#define LINUX_ADS1015_H + +#define ADS1015_CHANNELS 8 + +struct ads1015_channel_data { + bool enabled; + unsigned int pga; + unsigned int data_rate; +}; + +struct ads1015_platform_data { + struct ads1015_channel_data channel_data[ADS1015_CHANNELS]; +}; + +#endif /* LINUX_ADS1015_H */ diff --git a/include/linux/platform_data/apds990x.h b/include/linux/platform_data/apds990x.h new file mode 100644 index 000000000000..d186fcc5d257 --- /dev/null +++ b/include/linux/platform_data/apds990x.h @@ -0,0 +1,79 @@ +/* + * This file is part of the APDS990x sensor driver. + * Chip is combined proximity and ambient light sensor. + * + * Copyright (C) 2010 Nokia Corporation and/or its subsidiary(-ies). + * + * Contact: Samu Onkalo <samu.p.onkalo@nokia.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + */ + +#ifndef __APDS990X_H__ +#define __APDS990X_H__ + + +#define APDS_IRLED_CURR_12mA 0x3 +#define APDS_IRLED_CURR_25mA 0x2 +#define APDS_IRLED_CURR_50mA 0x1 +#define APDS_IRLED_CURR_100mA 0x0 + +/** + * struct apds990x_chip_factors - defines effect of the cover window + * @ga: Total glass attenuation + * @cf1: clear channel factor 1 for raw to lux conversion + * @irf1: IR channel factor 1 for raw to lux conversion + * @cf2: clear channel factor 2 for raw to lux conversion + * @irf2: IR channel factor 2 for raw to lux conversion + * @df: device factor for conversion formulas + * + * Structure for tuning ALS calculation to match with environment. + * Values depend on the material above the sensor and the sensor + * itself. If the GA is zero, driver will use uncovered sensor default values + * format: decimal value * APDS_PARAM_SCALE except df which is plain integer. + */ +#define APDS_PARAM_SCALE 4096 +struct apds990x_chip_factors { + int ga; + int cf1; + int irf1; + int cf2; + int irf2; + int df; +}; + +/** + * struct apds990x_platform_data - platform data for apsd990x.c driver + * @cf: chip factor data + * @pddrive: IR-led driving current + * @ppcount: number of IR pulses used for proximity estimation + * @setup_resources: interrupt line setup call back function + * @release_resources: interrupt line release call back function + * + * Proximity detection result depends heavily on correct ppcount, pdrive + * and cover window. + * + */ + +struct apds990x_platform_data { + struct apds990x_chip_factors cf; + u8 pdrive; + u8 ppcount; + int (*setup_resources)(void); + int (*release_resources)(void); +}; + +#endif diff --git a/include/linux/platform_data/atmel.h b/include/linux/platform_data/atmel.h index 3c8825b67298..cdceb4d4ef9d 100644 --- a/include/linux/platform_data/atmel.h +++ b/include/linux/platform_data/atmel.h @@ -7,10 +7,6 @@ #ifndef __ATMEL_H__ #define __ATMEL_H__ -#include <linux/mtd/nand.h> -#include <linux/mtd/partitions.h> -#include <linux/serial.h> - /* Compact Flash */ struct at91_cf_data { int irq_pin; /* I/O IRQ */ @@ -23,35 +19,14 @@ struct at91_cf_data { #define AT91_IDE_SWAP_A0_A2 0x02 }; - /* NAND / SmartMedia */ -struct atmel_nand_data { - int enable_pin; /* chip enable */ - int det_pin; /* card detect */ - int rdy_pin; /* ready/busy */ - u8 rdy_pin_active_low; /* rdy_pin value is inverted */ - u8 ale; /* address line number connected to ALE */ - u8 cle; /* address line number connected to CLE */ - u8 bus_width_16; /* buswidth is 16 bit */ - u8 ecc_mode; /* ecc mode */ - u8 on_flash_bbt; /* bbt on flash */ - struct mtd_partition *parts; - unsigned int num_parts; - bool has_dma; /* support dma transfer */ - - /* default is false, only for at32ap7000 chip is true */ - bool need_reset_workaround; -}; - - /* Serial */ -struct atmel_uart_data { - int num; /* port num */ - short use_dma_tx; /* use transmit DMA? */ - short use_dma_rx; /* use receive DMA? */ - void __iomem *regs; /* virt. base address, if any */ - struct serial_rs485 rs485; /* rs485 settings */ -}; - /* FIXME: this needs a better location, but gets stuff building again */ +#ifdef CONFIG_ATMEL_PM extern int at91_suspend_entering_slow_clock(void); +#else +static inline int at91_suspend_entering_slow_clock(void) +{ + return 0; +} +#endif #endif /* __ATMEL_H__ */ diff --git a/include/linux/platform_data/bh1770glc.h b/include/linux/platform_data/bh1770glc.h new file mode 100644 index 000000000000..8b5e2df36c72 --- /dev/null +++ b/include/linux/platform_data/bh1770glc.h @@ -0,0 +1,53 @@ +/* + * This file is part of the ROHM BH1770GLC / OSRAM SFH7770 sensor driver. + * Chip is combined proximity and ambient light sensor. + * + * Copyright (C) 2010 Nokia Corporation and/or its subsidiary(-ies). + * + * Contact: Samu Onkalo <samu.p.onkalo@nokia.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + */ + +#ifndef __BH1770_H__ +#define __BH1770_H__ + +/** + * struct bh1770_platform_data - platform data for bh1770glc driver + * @led_def_curr: IR led driving current. + * @glass_attenuation: Attenuation factor for covering window. + * @setup_resources: Call back for interrupt line setup function + * @release_resources: Call back for interrupte line release function + * + * Example of glass attenuation: 16384 * 385 / 100 means attenuation factor + * of 3.85. i.e. light_above_sensor = light_above_cover_window / 3.85 + */ + +struct bh1770_platform_data { +#define BH1770_LED_5mA 0 +#define BH1770_LED_10mA 1 +#define BH1770_LED_20mA 2 +#define BH1770_LED_50mA 3 +#define BH1770_LED_100mA 4 +#define BH1770_LED_150mA 5 +#define BH1770_LED_200mA 6 + __u8 led_def_curr; +#define BH1770_NEUTRAL_GA 16384 /* 16384 / 16384 = 1 */ + __u32 glass_attenuation; + int (*setup_resources)(void); + int (*release_resources)(void); +}; +#endif diff --git a/include/linux/platform_data/clk-realview.h b/include/linux/platform_data/clk-realview.h deleted file mode 100644 index 2e426a7dbc51..000000000000 --- a/include/linux/platform_data/clk-realview.h +++ /dev/null @@ -1 +0,0 @@ -void realview_clk_init(void __iomem *sysbase, bool is_pb1176); diff --git a/include/linux/platform_data/ds620.h b/include/linux/platform_data/ds620.h new file mode 100644 index 000000000000..736bb87ac0fc --- /dev/null +++ b/include/linux/platform_data/ds620.h @@ -0,0 +1,21 @@ +#ifndef _LINUX_DS620_H +#define _LINUX_DS620_H + +#include <linux/types.h> +#include <linux/i2c.h> + +/* platform data for the DS620 temperature sensor and thermostat */ + +struct ds620_platform_data { + /* + * Thermostat output pin PO mode: + * 0 = always low (default) + * 1 = PO_LOW + * 2 = PO_HIGH + * + * (see Documentation/hwmon/ds620) + */ + int pomode; +}; + +#endif /* _LINUX_DS620_H */ diff --git a/include/linux/platform_data/hsmmc-omap.h b/include/linux/platform_data/hsmmc-omap.h index 8e981be2e2c2..0ff1e0dba720 100644 --- a/include/linux/platform_data/hsmmc-omap.h +++ b/include/linux/platform_data/hsmmc-omap.h @@ -55,9 +55,6 @@ struct omap_hsmmc_platform_data { u32 caps; /* Used for the MMC driver on 2430 and later */ u32 pm_caps; /* PM capabilities of the mmc */ - /* use the internal clock */ - unsigned internal_clock:1; - /* nonremovable e.g. eMMC */ unsigned nonremovable:1; @@ -73,13 +70,6 @@ struct omap_hsmmc_platform_data { int gpio_cd; /* gpio (card detect) */ int gpio_cod; /* gpio (cover detect) */ int gpio_wp; /* gpio (write protect) */ - - int (*set_power)(struct device *dev, int power_on, int vdd); - void (*remux)(struct device *dev, int power_on); - /* Call back before enabling / disabling regulators */ - void (*before_set_reg)(struct device *dev, int power_on, int vdd); - /* Call back after enabling / disabling regulators */ - void (*after_set_reg)(struct device *dev, int power_on, int vdd); /* if we have special card, init it using this callback */ void (*init_card)(struct mmc_card *card); diff --git a/include/linux/platform_data/i2c-hid.h b/include/linux/platform_data/i2c-hid.h new file mode 100644 index 000000000000..1fb088239d12 --- /dev/null +++ b/include/linux/platform_data/i2c-hid.h @@ -0,0 +1,42 @@ +/* + * HID over I2C protocol implementation + * + * Copyright (c) 2012 Benjamin Tissoires <benjamin.tissoires@gmail.com> + * Copyright (c) 2012 Ecole Nationale de l'Aviation Civile, France + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file COPYING in the main directory of this archive for + * more details. + */ + +#ifndef __LINUX_I2C_HID_H +#define __LINUX_I2C_HID_H + +#include <linux/types.h> + +struct regulator; + +/** + * struct i2chid_platform_data - used by hid over i2c implementation. + * @hid_descriptor_address: i2c register where the HID descriptor is stored. + * @supply: regulator for powering on the device. + * @post_power_delay_ms: delay after powering on before device is usable. + * + * Note that it is the responsibility of the platform driver (or the acpi 5.0 + * driver, or the flattened device tree) to setup the irq related to the gpio in + * the struct i2c_board_info. + * The platform driver should also setup the gpio according to the device: + * + * A typical example is the following: + * irq = gpio_to_irq(intr_gpio); + * hkdk4412_i2c_devs5[0].irq = irq; // store the irq in i2c_board_info + * gpio_request(intr_gpio, "elan-irq"); + * s3c_gpio_setpull(intr_gpio, S3C_GPIO_PULL_UP); + */ +struct i2c_hid_platform_data { + u16 hid_descriptor_address; + struct regulator *supply; + int post_power_delay_ms; +}; + +#endif /* __LINUX_I2C_HID_H */ diff --git a/include/linux/platform_data/leds-pca963x.h b/include/linux/platform_data/leds-pca963x.h index e731f0036329..54e845ffb5ed 100644 --- a/include/linux/platform_data/leds-pca963x.h +++ b/include/linux/platform_data/leds-pca963x.h @@ -33,10 +33,16 @@ enum pca963x_blink_type { PCA963X_HW_BLINK, }; +enum pca963x_direction { + PCA963X_NORMAL, + PCA963X_INVERTED, +}; + struct pca963x_platform_data { struct led_platform_data leds; enum pca963x_outdrv outdrv; enum pca963x_blink_type blink_type; + enum pca963x_direction dir; }; #endif /* __LINUX_PCA963X_H*/ diff --git a/include/linux/platform_data/lm8323.h b/include/linux/platform_data/lm8323.h new file mode 100644 index 000000000000..478d668bc590 --- /dev/null +++ b/include/linux/platform_data/lm8323.h @@ -0,0 +1,46 @@ +/* + * lm8323.h - Configuration for LM8323 keypad driver. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation (version 2 of the License only). + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#ifndef __LINUX_LM8323_H +#define __LINUX_LM8323_H + +#include <linux/types.h> + +/* + * Largest keycode that the chip can send, plus one, + * so keys can be mapped directly at the index of the + * LM8323 keycode instead of subtracting one. + */ +#define LM8323_KEYMAP_SIZE (0x7f + 1) + +#define LM8323_NUM_PWMS 3 + +struct lm8323_platform_data { + int debounce_time; /* Time to watch for key bouncing, in ms. */ + int active_time; /* Idle time until sleep, in ms. */ + + int size_x; + int size_y; + bool repeat; + const unsigned short *keymap; + + const char *pwm_names[LM8323_NUM_PWMS]; + + const char *name; /* Device name. */ +}; + +#endif /* __LINUX_LM8323_H */ diff --git a/include/linux/platform_data/ltc4245.h b/include/linux/platform_data/ltc4245.h new file mode 100644 index 000000000000..56bda4be0016 --- /dev/null +++ b/include/linux/platform_data/ltc4245.h @@ -0,0 +1,21 @@ +/* + * Platform Data for LTC4245 hardware monitor chip + * + * Copyright (c) 2010 Ira W. Snyder <iws@ovro.caltech.edu> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#ifndef LINUX_LTC4245_H +#define LINUX_LTC4245_H + +#include <linux/types.h> + +struct ltc4245_platform_data { + bool use_extra_gpios; +}; + +#endif /* LINUX_LTC4245_H */ diff --git a/include/linux/platform_data/max6639.h b/include/linux/platform_data/max6639.h new file mode 100644 index 000000000000..6011c42034da --- /dev/null +++ b/include/linux/platform_data/max6639.h @@ -0,0 +1,14 @@ +#ifndef _LINUX_MAX6639_H +#define _LINUX_MAX6639_H + +#include <linux/types.h> + +/* platform data for the MAX6639 temperature sensor and fan control */ + +struct max6639_platform_data { + bool pwm_polarity; /* Polarity low (0) or high (1, default) */ + int ppr; /* Pulses per rotation 1..4 (default == 2) */ + int rpm_range; /* 2000, 4000 (default), 8000 or 16000 */ +}; + +#endif /* _LINUX_MAX6639_H */ diff --git a/include/linux/platform_data/max732x.h b/include/linux/platform_data/max732x.h new file mode 100644 index 000000000000..c04bac8bf2fe --- /dev/null +++ b/include/linux/platform_data/max732x.h @@ -0,0 +1,22 @@ +#ifndef __LINUX_I2C_MAX732X_H +#define __LINUX_I2C_MAX732X_H + +/* platform data for the MAX732x 8/16-bit I/O expander driver */ + +struct max732x_platform_data { + /* number of the first GPIO */ + unsigned gpio_base; + + /* interrupt base */ + int irq_base; + + void *context; /* param to setup/teardown */ + + int (*setup)(struct i2c_client *client, + unsigned gpio, unsigned ngpio, + void *context); + int (*teardown)(struct i2c_client *client, + unsigned gpio, unsigned ngpio, + void *context); +}; +#endif /* __LINUX_I2C_MAX732X_H */ diff --git a/include/linux/platform_data/mcs.h b/include/linux/platform_data/mcs.h new file mode 100644 index 000000000000..61bb18a4fd3c --- /dev/null +++ b/include/linux/platform_data/mcs.h @@ -0,0 +1,35 @@ +/* + * Copyright (C) 2009 - 2010 Samsung Electronics Co.Ltd + * Author: Joonyoung Shim <jy0922.shim@samsung.com> + * Author: HeungJun Kim <riverful.kim@samsung.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ + +#ifndef __LINUX_MCS_H +#define __LINUX_MCS_H + +#define MCS_KEY_MAP(v, c) ((((v) & 0xff) << 16) | ((c) & 0xffff)) +#define MCS_KEY_VAL(v) (((v) >> 16) & 0xff) +#define MCS_KEY_CODE(v) ((v) & 0xffff) + +struct mcs_platform_data { + void (*poweron)(bool); + void (*cfg_pin)(void); + + /* touchscreen */ + unsigned int x_size; + unsigned int y_size; + + /* touchkey */ + const u32 *keymap; + unsigned int keymap_size; + unsigned int key_maxval; + bool no_autorepeat; +}; + +#endif /* __LINUX_MCS_H */ diff --git a/include/linux/platform_data/microchip-ksz.h b/include/linux/platform_data/microchip-ksz.h new file mode 100644 index 000000000000..84789ca634aa --- /dev/null +++ b/include/linux/platform_data/microchip-ksz.h @@ -0,0 +1,29 @@ +/* + * Microchip KSZ series switch platform data + * + * Copyright (C) 2017 + * + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. + * + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR + * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN + * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + */ + +#ifndef __MICROCHIP_KSZ_H +#define __MICROCHIP_KSZ_H + +#include <linux/kernel.h> + +struct ksz_platform_data { + u32 chip_id; + u16 enabled_ports; +}; + +#endif diff --git a/include/linux/platform_data/mms114.h b/include/linux/platform_data/mms114.h new file mode 100644 index 000000000000..5722ebfb2738 --- /dev/null +++ b/include/linux/platform_data/mms114.h @@ -0,0 +1,24 @@ +/* + * Copyright (C) 2012 Samsung Electronics Co.Ltd + * Author: Joonyoung Shim <jy0922.shim@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundationr + */ + +#ifndef __LINUX_MMS114_H +#define __LINUX_MMS114_H + +struct mms114_platform_data { + unsigned int x_size; + unsigned int y_size; + unsigned int contact_threshold; + unsigned int moving_threshold; + bool x_invert; + bool y_invert; + + void (*cfg_pin)(bool); +}; + +#endif /* __LINUX_MMS114_H */ diff --git a/include/linux/platform_data/nfcmrvl.h b/include/linux/platform_data/nfcmrvl.h index a6f9d633f5be..9e75ac8d19be 100644 --- a/include/linux/platform_data/nfcmrvl.h +++ b/include/linux/platform_data/nfcmrvl.h @@ -23,7 +23,7 @@ struct nfcmrvl_platform_data { */ /* GPIO that is wired to RESET_N signal */ - unsigned int reset_n_io; + int reset_n_io; /* Tell if transport is muxed in HCI one */ unsigned int hci_muxed; diff --git a/include/linux/platform_data/omapdss.h b/include/linux/platform_data/omapdss.h index 679177929045..7feb011ed500 100644 --- a/include/linux/platform_data/omapdss.h +++ b/include/linux/platform_data/omapdss.h @@ -27,7 +27,6 @@ enum omapdss_version { /* Board specific data */ struct omap_dss_board_info { - const char *default_display_name; int (*dsi_enable_pads)(int dsi_id, unsigned int lane_mask); void (*dsi_disable_pads)(int dsi_id, unsigned int lane_mask); int (*set_min_bus_tput)(struct device *dev, unsigned long r); diff --git a/include/linux/platform_data/pcf857x.h b/include/linux/platform_data/pcf857x.h new file mode 100644 index 000000000000..0767a2a6b2f1 --- /dev/null +++ b/include/linux/platform_data/pcf857x.h @@ -0,0 +1,44 @@ +#ifndef __LINUX_PCF857X_H +#define __LINUX_PCF857X_H + +/** + * struct pcf857x_platform_data - data to set up pcf857x driver + * @gpio_base: number of the chip's first GPIO + * @n_latch: optional bit-inverse of initial register value; if + * you leave this initialized to zero the driver will act + * like the chip was just reset + * @setup: optional callback issued once the GPIOs are valid + * @teardown: optional callback issued before the GPIOs are invalidated + * @context: optional parameter passed to setup() and teardown() + * + * In addition to the I2C_BOARD_INFO() state appropriate to each chip, + * the i2c_board_info used with the pcf875x driver must provide its + * platform_data (pointer to one of these structures) with at least + * the gpio_base value initialized. + * + * The @setup callback may be used with the kind of board-specific glue + * which hands the (now-valid) GPIOs to other drivers, or which puts + * devices in their initial states using these GPIOs. + * + * These GPIO chips are only "quasi-bidirectional"; read the chip specs + * to understand the behavior. They don't have separate registers to + * record which pins are used for input or output, record which output + * values are driven, or provide access to input values. That must be + * inferred by reading the chip's value and knowing the last value written + * to it. If you leave n_latch initialized to zero, that last written + * value is presumed to be all ones (as if the chip were just reset). + */ +struct pcf857x_platform_data { + unsigned gpio_base; + unsigned n_latch; + + int (*setup)(struct i2c_client *client, + int gpio, unsigned ngpio, + void *context); + int (*teardown)(struct i2c_client *client, + int gpio, unsigned ngpio, + void *context); + void *context; +}; + +#endif /* __LINUX_PCF857X_H */ diff --git a/include/linux/platform_data/spi-mt65xx.h b/include/linux/platform_data/spi-mt65xx.h index 54b04483976c..ba4e4bb70262 100644 --- a/include/linux/platform_data/spi-mt65xx.h +++ b/include/linux/platform_data/spi-mt65xx.h @@ -16,5 +16,7 @@ struct mtk_chip_config { u32 tx_mlsb; u32 rx_mlsb; + u32 cs_pol; + u32 sample_sel; }; #endif diff --git a/include/linux/platform_data/st-nci.h b/include/linux/platform_data/st-nci.h deleted file mode 100644 index f6494b347c06..000000000000 --- a/include/linux/platform_data/st-nci.h +++ /dev/null @@ -1,31 +0,0 @@ -/* - * Driver include for ST NCI NFC chip family. - * - * Copyright (C) 2014-2015 STMicroelectronics SAS. All rights reserved. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms and conditions of the GNU General Public License, - * version 2, as published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, see <http://www.gnu.org/licenses/>. - */ - -#ifndef _ST_NCI_H_ -#define _ST_NCI_H_ - -#define ST_NCI_DRIVER_NAME "st_nci" - -struct st_nci_nfc_platform_data { - unsigned int gpio_reset; - unsigned int irq_polarity; - bool is_ese_present; - bool is_uicc_present; -}; - -#endif /* _ST_NCI_H_ */ diff --git a/include/linux/platform_data/st_sensors_pdata.h b/include/linux/platform_data/st_sensors_pdata.h index 79b0e4cdb814..f8274b0c6888 100644 --- a/include/linux/platform_data/st_sensors_pdata.h +++ b/include/linux/platform_data/st_sensors_pdata.h @@ -17,10 +17,12 @@ * Available only for accelerometer and pressure sensors. * Accelerometer DRDY on LSM330 available only on pin 1 (see datasheet). * @open_drain: set the interrupt line to be open drain if possible. + * @spi_3wire: enable spi-3wire mode. */ struct st_sensors_platform_data { u8 drdy_int_pin; bool open_drain; + bool spi_3wire; }; #endif /* ST_SENSORS_PDATA_H */ diff --git a/include/linux/platform_data/tsc2007.h b/include/linux/platform_data/tsc2007.h new file mode 100644 index 000000000000..c2d3aa1dadd4 --- /dev/null +++ b/include/linux/platform_data/tsc2007.h @@ -0,0 +1,22 @@ +#ifndef __LINUX_I2C_TSC2007_H +#define __LINUX_I2C_TSC2007_H + +/* linux/platform_data/tsc2007.h */ + +struct tsc2007_platform_data { + u16 model; /* 2007. */ + u16 x_plate_ohms; /* must be non-zero value */ + u16 max_rt; /* max. resistance above which samples are ignored */ + unsigned long poll_period; /* time (in ms) between samples */ + int fuzzx; /* fuzz factor for X, Y and pressure axes */ + int fuzzy; + int fuzzz; + + int (*get_pendown_state)(struct device *); + /* If needed, clear 2nd level interrupt source */ + void (*clear_penirq)(void); + int (*init_platform_hw)(void); + void (*exit_platform_hw)(void); +}; + +#endif diff --git a/include/linux/platform_data/usb-ohci-s3c2410.h b/include/linux/platform_data/usb-ohci-s3c2410.h index 7fa1fbefc3f2..cc7554ae6e8b 100644 --- a/include/linux/platform_data/usb-ohci-s3c2410.h +++ b/include/linux/platform_data/usb-ohci-s3c2410.h @@ -31,7 +31,7 @@ struct s3c2410_hcd_info { void (*report_oc)(struct s3c2410_hcd_info *, int ports); }; -static void inline s3c2410_usb_report_oc(struct s3c2410_hcd_info *info, int ports) +static inline void s3c2410_usb_report_oc(struct s3c2410_hcd_info *info, int ports) { if (info->report_oc != NULL) { (info->report_oc)(info, ports); |