diff options
Diffstat (limited to 'include/linux/regulator')
| -rw-r--r-- | include/linux/regulator/consumer.h | 4 | ||||
| -rw-r--r-- | include/linux/regulator/driver.h | 7 | ||||
| -rw-r--r-- | include/linux/regulator/fixed.h | 24 | ||||
| -rw-r--r-- | include/linux/regulator/machine.h | 26 | ||||
| -rw-r--r-- | include/linux/regulator/max1586.h | 4 |
5 files changed, 58 insertions, 7 deletions
diff --git a/include/linux/regulator/consumer.h b/include/linux/regulator/consumer.h index 277f4b964df5..490c5b37b6d7 100644 --- a/include/linux/regulator/consumer.h +++ b/include/linux/regulator/consumer.h @@ -125,6 +125,8 @@ struct regulator_bulk_data { /* regulator get and put */ struct regulator *__must_check regulator_get(struct device *dev, const char *id); +struct regulator *__must_check regulator_get_exclusive(struct device *dev, + const char *id); void regulator_put(struct regulator *regulator); /* regulator output control and status */ @@ -144,6 +146,8 @@ void regulator_bulk_free(int num_consumers, int regulator_count_voltages(struct regulator *regulator); int regulator_list_voltage(struct regulator *regulator, unsigned selector); +int regulator_is_supported_voltage(struct regulator *regulator, + int min_uV, int max_uV); int regulator_set_voltage(struct regulator *regulator, int min_uV, int max_uV); int regulator_get_voltage(struct regulator *regulator); int regulator_set_current_limit(struct regulator *regulator, diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h index 225f733e7533..31f2055eae28 100644 --- a/include/linux/regulator/driver.h +++ b/include/linux/regulator/driver.h @@ -37,7 +37,8 @@ enum regulator_status { * * @enable: Configure the regulator as enabled. * @disable: Configure the regulator as disabled. - * @is_enabled: Return 1 if the regulator is enabled, 0 otherwise. + * @is_enabled: Return 1 if the regulator is enabled, 0 if not. + * May also return negative errno. * * @set_voltage: Set the voltage for the regulator within the range specified. * The driver should select the voltage closest to min_uV. @@ -162,6 +163,8 @@ struct regulator_desc { struct regulator_dev { struct regulator_desc *desc; int use_count; + int open_count; + int exclusive; /* lists we belong to */ struct list_head list; /* list of all regulators */ @@ -193,6 +196,8 @@ void *rdev_get_drvdata(struct regulator_dev *rdev); struct device *rdev_get_dev(struct regulator_dev *rdev); int rdev_get_id(struct regulator_dev *rdev); +int regulator_mode_to_status(unsigned int); + void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data); #endif diff --git a/include/linux/regulator/fixed.h b/include/linux/regulator/fixed.h index 91b4da31f1b5..e94a4a1c7c8a 100644 --- a/include/linux/regulator/fixed.h +++ b/include/linux/regulator/fixed.h @@ -5,6 +5,9 @@ * * Author: Mark Brown <broonie@opensource.wolfsonmicro.com> * + * Copyright (c) 2009 Nokia Corporation + * Roger Quadros <ext-roger.quadros@nokia.com> + * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of the @@ -16,9 +19,30 @@ struct regulator_init_data; +/** + * struct fixed_voltage_config - fixed_voltage_config structure + * @supply_name: Name of the regulator supply + * @microvolts: Output voltage of regulator + * @gpio: GPIO to use for enable control + * set to -EINVAL if not used + * @enable_high: Polarity of enable GPIO + * 1 = Active high, 0 = Active low + * @enabled_at_boot: Whether regulator has been enabled at + * boot or not. 1 = Yes, 0 = No + * This is used to keep the regulator at + * the default state + * @init_data: regulator_init_data + * + * This structure contains fixed voltage regulator configuration + * information that must be passed by platform code to the fixed + * voltage regulator driver. + */ struct fixed_voltage_config { const char *supply_name; int microvolts; + int gpio; + unsigned enable_high:1; + unsigned enabled_at_boot:1; struct regulator_init_data *init_data; }; diff --git a/include/linux/regulator/machine.h b/include/linux/regulator/machine.h index bac64fa390f2..87f5f176d4ef 100644 --- a/include/linux/regulator/machine.h +++ b/include/linux/regulator/machine.h @@ -41,7 +41,7 @@ struct regulator; #define REGULATOR_CHANGE_DRMS 0x10 /** - * struct regulator_state - regulator state during low power syatem states + * struct regulator_state - regulator state during low power system states * * This describes a regulators state during a system wide low power state. * @@ -117,25 +117,37 @@ struct regulation_constraints { /* mode to set on startup */ unsigned int initial_mode; - /* constriant flags */ + /* constraint flags */ unsigned always_on:1; /* regulator never off when system is on */ unsigned boot_on:1; /* bootloader/firmware enabled regulator */ - unsigned apply_uV:1; /* apply uV constraint iff min == max */ + unsigned apply_uV:1; /* apply uV constraint if min == max */ }; /** * struct regulator_consumer_supply - supply -> device mapping * - * This maps a supply name to a device. + * This maps a supply name to a device. Only one of dev or dev_name + * can be specified. Use of dev_name allows support for buses which + * make struct device available late such as I2C and is the preferred + * form. * * @dev: Device structure for the consumer. + * @dev_name: Result of dev_name() for the consumer. * @supply: Name for the supply. */ struct regulator_consumer_supply { struct device *dev; /* consumer */ + const char *dev_name; /* dev_name() for consumer */ const char *supply; /* consumer supply - e.g. "vcc" */ }; +/* Initialize struct regulator_consumer_supply */ +#define REGULATOR_SUPPLY(_name, _dev_name) \ +{ \ + .supply = _name, \ + .dev_name = _dev_name, \ +} + /** * struct regulator_init_data - regulator platform initialisation data. * @@ -166,6 +178,12 @@ struct regulator_init_data { int regulator_suspend_prepare(suspend_state_t state); +#ifdef CONFIG_REGULATOR void regulator_has_full_constraints(void); +#else +static inline void regulator_has_full_constraints(void) +{ +} +#endif #endif diff --git a/include/linux/regulator/max1586.h b/include/linux/regulator/max1586.h index 44563192bf16..de9a7fae20be 100644 --- a/include/linux/regulator/max1586.h +++ b/include/linux/regulator/max1586.h @@ -36,7 +36,7 @@ * max1586_subdev_data - regulator data * @id: regulator Id (either MAX1586_V3 or MAX1586_V6) * @name: regulator cute name (example for V3: "vcc_core") - * @platform_data: regulator init data (contraints, supplies, ...) + * @platform_data: regulator init data (constraints, supplies, ...) */ struct max1586_subdev_data { int id; @@ -46,7 +46,7 @@ struct max1586_subdev_data { /** * max1586_platform_data - platform data for max1586 - * @num_subdevs: number of regultors used (may be 1 or 2) + * @num_subdevs: number of regulators used (may be 1 or 2) * @subdevs: regulator used * At most, there will be a regulator for V3 and one for V6 voltages. * @v3_gain: gain on the V3 voltage output multiplied by 1e6. |