| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Introduce a Page-Reuse mechanism in non-Striding RQ RX datapath.
A WQE (RX descriptor) buffer is a page, that in most cases was fully
wasted on a packet that is much smaller, requiring a new page for
the next round.
In this patch, we implement a page-reuse mechanism, that resembles a
`SW Striding RQ`.
We allow the WQE to reuse its allocated page as much as it could,
until the page is fully consumed. In each round, the WQE is capable
of receiving packet of maximal size (MTU). Yet, upon the reception of
a packet, the WQE knows the actual packet size, and consumes the exact
amount of memory needed to build a linear SKB. Then, it updates the
buffer pointer within the page accordingly, for the next round.
Feature is mutually exclusive with XDP (packet-per-page)
and LRO (session size is a power of two, needs unused page).
Performance tests:
iperf tcp tests show huge gain:
--------------------------------------------
num streams | BW before | BW after | ratio |
1 | 22.2 | 30.9 | 1.39x |
8 | 64.2 | 93.6 | 1.46x |
64 | 56.7 | 91.4 | 1.61x |
--------------------------------------------
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In the RX memory scheme of non Striding RQ, we use linear SKBs.
Keeping NET_IP_ALIGN in headroom can improve performance on some archs.
In addition, take this headroom into account when calculating the
LRO WQE size.
These are not needed in Striding RQ as they're done implicitly
within the non-linear SKB allocation.
Fixes: 1bfecfca565c ("net/mlx5e: Build RX SKB on demand")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Build the SKB over the receive packet instead of the
whole page. Getting the SKB's linear data and shared_info
closer improves locality.
In addition, this opens up the possibility to make use of
other parts of the page in the downstream page-reuse patch.
Fixes: 1bfecfca565c ("net/mlx5e: Build RX SKB on demand")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|\
| |
| |
| |
| |
| |
| |
| |
| | |
Two entries being added at the same time to the IFLA
policy table, whilst parallel bug fixes to decnet
routing dst handling overlapping with the dst gc removal
in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Pull networking fixes from David Miller:
1) Fix refcounting wrt timers which hold onto inet6 address objects,
from Xin Long.
2) Fix an ancient bug in wireless wext ioctls, from Johannes Berg.
3) Firmware handling fixes in brcm80211 driver, from Arend Van Spriel.
4) Several mlx5 driver fixes (firmware readiness, timestamp cap
reporting, devlink command validity checking, tc offloading, etc.)
From Eli Cohen, Maor Dickman, Chris Mi, and Or Gerlitz.
5) Fix dst leak in IP/IP6 tunnels, from Haishuang Yan.
6) Fix dst refcount bug in decnet, from Wei Wang.
7) Netdev can be double freed in register_vlan_device(). Fix from Gao
Feng.
8) Don't allow object to be destroyed while it is being dumped in SCTP,
from Xin Long.
9) Fix dpaa_eth build when modular, from Madalin Bucur.
10) Fix throw route leaks, from Serhey Popovych.
11) IFLA_GROUP missing from if_nlmsg_size() and ifla_policy[] table,
also from Serhey Popovych.
12) Fix premature TX SKB free in stmmac, from Niklas Cassel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
igmp: add a missing spin_lock_init()
net: stmmac: free an skb first when there are no longer any descriptors using it
sfc: remove duplicate up_write on VF filter_sem
rtnetlink: add IFLA_GROUP to ifla_policy
ipv6: Do not leak throw route references
dt-bindings: net: sms911x: Add missing optional VDD regulators
dpaa_eth: reuse the dma_ops provided by the FMan MAC device
fsl/fman: propagate dma_ops
net/core: remove explicit do_softirq() from busy_poll_stop()
fib_rules: Resolve goto rules target on delete
sctp: ensure ep is not destroyed before doing the dump
net/hns:bugfix of ethtool -t phy self_test
net: 8021q: Fix one possible panic caused by BUG_ON in free_netdev
cxgb4: notify uP to route ctrlq compl to rdma rspq
ip6_tunnel: Correct tos value in collect_md mode
decnet: always not take dst->__refcnt when inserting dst into hash table
ip6_tunnel: fix potential issue in __ip6_tnl_rcv
ip_tunnel: fix potential issue in ip_tunnel_rcv
brcmfmac: fix uninitialized warning in brcmf_usb_probe_phase2()
net/mlx5e: Avoid doing a cleanup call if the profile doesn't have it
...
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Andrey reported a lockdep warning on non-initialized
spinlock:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 1 PID: 4099 Comm: a.out Not tainted 4.12.0-rc6+ #9
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16
dump_stack+0x292/0x395 lib/dump_stack.c:52
register_lock_class+0x717/0x1aa0 kernel/locking/lockdep.c:755
? 0xffffffffa0000000
__lock_acquire+0x269/0x3690 kernel/locking/lockdep.c:3255
lock_acquire+0x22d/0x560 kernel/locking/lockdep.c:3855
__raw_spin_lock_bh ./include/linux/spinlock_api_smp.h:135
_raw_spin_lock_bh+0x36/0x50 kernel/locking/spinlock.c:175
spin_lock_bh ./include/linux/spinlock.h:304
ip_mc_clear_src+0x27/0x1e0 net/ipv4/igmp.c:2076
igmpv3_clear_delrec+0xee/0x4f0 net/ipv4/igmp.c:1194
ip_mc_destroy_dev+0x4e/0x190 net/ipv4/igmp.c:1736
We miss a spin_lock_init() in igmpv3_add_delrec(), probably
because previously we never use it on this code path. Since
we already unlink it from the global mc_tomb list, it is
probably safe not to acquire this spinlock here. It does not
harm to have it although, to avoid conditional locking.
Fixes: c38b7d327aaf ("igmp: acquire pmc lock for ip_mc_clear_src()")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.12
Two important fixes for brcmfmac. The rest of the brcmfmac patches are
either code preparation and fixing a new build warning.
brcmfmac
* fix a NULL pointer dereference during resume
* fix a NULL pointer dereference with USB devices, a regression from
v4.12-rc1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This fixes the following warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c: In function
'brcmf_usb_probe_phase2':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c:1198:2:
warning: 'devinfo' may be used uninitialized in this function
[-Wmaybe-uninitialized]
mutex_unlock(&devinfo->dev_init_lock);
Fixes: 6d0507a777fb ("brcmfmac: add parameter to pass error code in firmware callback")
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
USB devices rely on queuing functionality provided by the fwsignal
module regardless the mode fwsignal is operating in. For this some
data structure needs to be reserved which is tied to the interface,
which is done by brcmf_fws_add_interface(). However, it checks the
mode. Replace that by checking result from brcmf_fws_queue_skbs().
Otherwise the driver will crash in a null pointer dereference when
data is transmitted on the interface.
Fixes: fc0471e3e884 ("brcmfmac: ignore interfaces when fwsignal is disabled")
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When request firmware fails, brcmf_ops_sdio_remove is being called and
brcmf_bus freed. In such circumstancies if you do a suspend/resume cycle
the kernel hangs on resume due a NULL pointer dereference in resume
function. So in brcmf_sdio_firmware_callback() we need to unbind the
driver from both sdio_func devices when firmware load failure is indicated.
Cc: stable@vger.kernel.org # 4.9.x-
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When firmware loading failed the code used to unbind the device provided
by the calling code. However, for the sdio driver two devices are bound
and both need to be released upon failure. The callback has been extended
with parameter to pass error code so add that in this commit upon firmware
loading failure.
Cc: stable@vger.kernel.org # 4.9.x-
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Extend the parameters in the firmware callback so it can be called
upon success and failure. This allows the caller to properly clear
all resources in the failure path. Right now the error code is
always zero, ie. success.
Cc: stable@vger.kernel.org # 4.9.x-
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When having the skb pointer in the first descriptor, stmmac_tx_clean
can get called at a moment where the IP has only cleared the own bit
of the first descriptor, thus freeing the skb, even though there can
be several descriptors whose buffers point into the same skb.
By simply moving the skb pointer from the first descriptor to the last
descriptor, a skb will get freed only when the IP has cleared the
own bit of all the descriptors that are using that skb.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Somehow two copies of the line 'up_write(&vf->efx->filter_sem);' got into
efx_ef10_sriov_set_vf_vlan(). This would put the mutex in a bad state and
cause all subsequent down attempts to hang.
Fixes: 671b53eec2ed ("sfc: Ensure down_write(&filter_sem) and up_write() are matched before calling efx_net_open()")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Network interface groups support added while ago, however
there is no IFLA_GROUP attribute description in policy
and netlink message size calculations until now.
Add IFLA_GROUP attribute to the policy.
Fixes: cbda10fa97d7 ("net_device: add support for network device groups")
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
While commit 73ba57bfae4a ("ipv6: fix backtracking for throw routes")
does good job on error propagation to the fib_rules_lookup()
in fib rules core framework that also corrects throw routes
handling, it does not solve route reference leakage problem
happened when we return -EAGAIN to the fib_rules_lookup()
and leave routing table entry referenced in arg->result.
If rule with matched throw route isn't last matched in the
list we overwrite arg->result losing reference on throw
route stored previously forever.
We also partially revert commit ab997ad40839 ("ipv6: fix the
incorrect return value of throw route") since we never return
routing table entry with dst.error == -EAGAIN when
CONFIG_IPV6_MULTIPLE_TABLES is on. Also there is no point
to check for RTF_REJECT flag since it is always set throw
route.
Fixes: 73ba57bfae4a ("ipv6: fix backtracking for throw routes")
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The lan911x family of devices require supplying from 3.3 V power
supplies (connected to VDD_IO, VDD_A and VREG_3.3 pins). The existing
driver however obtains only VDD_IO and VDD_A regulators in an optional
way so document this in bindings.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Madalin Bucur says:
====================
net: fix loadable module for DPAA Ethernet
The DPAA Ethernet makes use of a symbol that is not exported.
Address the issue by propagating the dma_ops rather than calling
arch_setup_dma_ops().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Remove the use of arch_setup_dma_ops() that was not exported
and was breaking loadable module compilation.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |/ /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Make sure dma_ops are set, to be later used by the Ethernet driver.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Since commit 217f69743681 ("net: busy-poll: allow preemption in
sk_busy_loop()") there is an explicit do_softirq() invocation after
local_bh_enable() has been invoked.
I don't understand why we need this because local_bh_enable() will
invoke do_softirq() once the softirq counter reached zero and we have
softirq-related work pending.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
We should avoid marking goto rules unresolved when their
target is actually reachable after rule deletion.
Consolder following sample scenario:
# ip -4 ru sh
0: from all lookup local
32000: from all goto 32100
32100: from all lookup main
32100: from all lookup default
32766: from all lookup main
32767: from all lookup default
# ip -4 ru del pref 32100 table main
# ip -4 ru sh
0: from all lookup local
32000: from all goto 32100 [unresolved]
32100: from all lookup default
32766: from all lookup main
32767: from all lookup default
After removal of first rule with preference 32100 we
mark all goto rules as unreachable, even when rule with
same preference as removed one still present.
Check if next rule with same preference is available
and make all rules with goto action pointing to it.
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Now before dumping a sock in sctp_diag, it only holds the sock while
the ep may be already destroyed. It can cause a use-after-free panic
when accessing ep->asocs.
This patch is to set sctp_sk(sk)->ep NULL in sctp_endpoint_destroy,
and check if this ep is already destroyed before dumping this ep.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdrver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch fixes the phy loopback self_test failed issue. when
Marvell Phy Module is loaded, it will powerdown fiber when doing
phy loopback self test, which cause phy loopback self_test fail.
Signed-off-by: Lin Yun Sheng <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The register_vlan_device would invoke free_netdev directly, when
register_vlan_dev failed. It would trigger the BUG_ON in free_netdev
if the dev was already registered. In this case, the netdev would be
freed in netdev_run_todo later.
So add one condition check now. Only when dev is not registered, then
free it directly.
The following is the part coredump when netdev_upper_dev_link failed
in register_vlan_dev. I removed the lines which are too long.
[ 411.237457] ------------[ cut here ]------------
[ 411.237458] kernel BUG at net/core/dev.c:7998!
[ 411.237484] invalid opcode: 0000 [#1] SMP
[ 411.237705] [last unloaded: 8021q]
[ 411.237718] CPU: 1 PID: 12845 Comm: vconfig Tainted: G E 4.12.0-rc5+ #6
[ 411.237737] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/02/2015
[ 411.237764] task: ffff9cbeb6685580 task.stack: ffffa7d2807d8000
[ 411.237782] RIP: 0010:free_netdev+0x116/0x120
[ 411.237794] RSP: 0018:ffffa7d2807dbdb0 EFLAGS: 00010297
[ 411.237808] RAX: 0000000000000002 RBX: ffff9cbeb6ba8fd8 RCX: 0000000000001878
[ 411.237826] RDX: 0000000000000001 RSI: 0000000000000282 RDI: 0000000000000000
[ 411.237844] RBP: ffffa7d2807dbdc8 R08: 0002986100029841 R09: 0002982100029801
[ 411.237861] R10: 0004000100029980 R11: 0004000100029980 R12: ffff9cbeb6ba9000
[ 411.238761] R13: ffff9cbeb6ba9060 R14: ffff9cbe60f1a000 R15: ffff9cbeb6ba9000
[ 411.239518] FS: 00007fb690d81700(0000) GS:ffff9cbebb640000(0000) knlGS:0000000000000000
[ 411.239949] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 411.240454] CR2: 00007f7115624000 CR3: 0000000077cdf000 CR4: 00000000003406e0
[ 411.240936] Call Trace:
[ 411.241462] vlan_ioctl_handler+0x3f1/0x400 [8021q]
[ 411.241910] sock_ioctl+0x18b/0x2c0
[ 411.242394] do_vfs_ioctl+0xa1/0x5d0
[ 411.242853] ? sock_alloc_file+0xa6/0x130
[ 411.243465] SyS_ioctl+0x79/0x90
[ 411.243900] entry_SYSCALL_64_fastpath+0x1e/0xa9
[ 411.244425] RIP: 0033:0x7fb69089a357
[ 411.244863] RSP: 002b:00007ffcd04e0fc8 EFLAGS: 00000202 ORIG_RAX: 0000000000000010
[ 411.245445] RAX: ffffffffffffffda RBX: 00007ffcd04e2884 RCX: 00007fb69089a357
[ 411.245903] RDX: 00007ffcd04e0fd0 RSI: 0000000000008983 RDI: 0000000000000003
[ 411.246527] RBP: 00007ffcd04e0fd0 R08: 0000000000000000 R09: 1999999999999999
[ 411.246976] R10: 000000000000053f R11: 0000000000000202 R12: 0000000000000004
[ 411.247414] R13: 00007ffcd04e1128 R14: 00007ffcd04e2888 R15: 0000000000000001
[ 411.249129] RIP: free_netdev+0x116/0x120 RSP: ffffa7d2807dbdb0
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
During the module initialisation there is a possible race
(basically race between uld and lld) where neither the uld
nor lld notifies the uP about where to route the ctrl queue
completions. LLD skips notifying uP as the rdma queues were
not created by then (will leave it to ULD to notify the uP).
As the ULD comes up, it also skips notifying the uP as the
flag FULL_INIT_DONE is not set yet (ULD assumes that the
interface is not up yet).
Consequently, this race between uld and lld leaves uP
unnotified about where to send the ctrl queue completions
to, leading to iwarp RI_RES WR failure.
Here is the race:
CPU 0 CPU1
- allocates nic rx queus
- t4_sge_alloc_ctrl_txq()
(if rdma rsp queues exists,
tell uP to route ctrl queue
compl to rdma rspq)
- acquires the mutex_lock
- allocates rdma response queues
- if FULL_INIT_DONE set,
tell uP to route ctrl queue compl
to rdma rspq
- relinquishes mutex_lock
- acquires the mutex_lock
- enable_rx()
- set FULL_INIT_DONE
- relinquishes mutex_lock
This patch fixes the above issue.
Fixes: e7519f9926f1('cxgb4: avoid enabling napi twice to the same queue')
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
CC: Stable <stable@vger.kernel.org> # 4.9+
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here's just the fix for that ancient bug:
* remove wext calling ndo_do_ioctl, since nobody needs
that now and it makes the type change easier
* use struct iwreq instead of struct ifreq almost everywhere
in wireless extensions code
* copy only struct iwreq from userspace in dev_ioctl for the
wireless extensions, since it's smaller than struct ifreq
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Unfortunately, struct iwreq isn't a proper subset of struct ifreq,
but is still handled by the same code path. Robert reported that
then applications may (randomly) fault if the struct iwreq they
pass happens to land within 8 bytes of the end of a mapping (the
struct is only 32 bytes, vs. struct ifreq's 40 bytes).
To fix this, pull out the code handling wireless extension ioctls
and copy only the smaller structure in this case.
This bug goes back a long time, I tracked that it was introduced
into mainline in 2.1.15, over 20 years ago!
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195869
Reported-by: Robert O'Callahan <robert@ocallahan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
To make it clear that we never use struct ifreq, cast from it
directly in the wext entrypoint and use struct iwreq from there
on. The next patch will remove the cast again and pass the
correct struct from the beginning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
There are no longer any drivers (in the tree proper, I didn't
check all the staging drivers) that take WEXT ioctls through
this API, the only remaining ones that even have ndo_do_ioctl
are using it only for private ioctls.
Therefore, we can remove this call.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Same as ip_gre, geneve and vxlan, use key->tos as traffic class value.
CC: Peter Dawson <petedaws@gmail.com>
Fixes: 0e9a709560db ("ip6_tunnel, ip6_gre: fix setting of DSCP on
encapsulated packets”)
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: Peter Dawson <peter.a.dawson@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
In the existing dn_route.c code, dn_route_output_slow() takes
dst->__refcnt before calling dn_insert_route() while dn_route_input_slow()
does not take dst->__refcnt before calling dn_insert_route().
This makes the whole routing code very buggy.
In dn_dst_check_expire(), dnrt_free() is called when rt expires. This
makes the routes inserted by dn_route_output_slow() not able to be
freed as the refcnt is not released.
In dn_dst_gc(), dnrt_drop() is called to release rt which could
potentially cause the dst->__refcnt to be dropped to -1.
In dn_run_flush(), dst_free() is called to release all the dst. Again,
it makes the dst inserted by dn_route_output_slow() not able to be
released and also, it does not wait on the rcu and could potentially
cause crash in the path where other users still refer to this dst.
This patch makes sure both input and output path do not take
dst->__refcnt before calling dn_insert_route() and also makes sure
dnrt_free()/dst_free() is called when removing dst from the hash table.
The only difference between those 2 calls is that dnrt_free() waits on
the rcu while dst_free() does not.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
When __ip6_tnl_rcv fails, the tun_dst won't be freed, so call
dst_release to free it in error code path.
Fixes: 8d79266bc48c ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
CC: Alexei Starovoitov <ast@fb.com>
Tested-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
When ip_tunnel_rcv fails, the tun_dst won't be freed, so call
dst_release to free it in error code path.
Fixes: 2e15ea390e6f ("ip_gre: Add support to collect tunnel metadata.")
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Tested-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox mlx5 fixes 2017-06-14
This series contains some fixes for the mlx5 core and netdev driver.
Please pull and let me know if there's any problem.
For -stable:
("net/mlx5: Wait for FW readiness before initializing command interface") kernels >= 4.4
("net/mlx5e: Fix timestamping capabilities reporting") kernels >= 4.5
("net/mlx5e: Avoid doing a cleanup call if the profile doesn't have it") kernels >= 4.9
("net/mlx5e: Fix min inline value for VF rep SQs") kernels >= 4.11
The "net/mlx5e: Fix min inline .." (a oneliner patch) doesn't cleanly apply
to 4.11, it hits a contextual conflict and can be easily resolved by:
+ mlx5_query_min_inline(mdev, &priv->params.tx_min_inline_mode);
to the end of mlx5e_build_rep_netdev_priv. Note the 2nd parameter of
mlx5_query_min_inline is slightly different from the original one.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The error flow of mlx5e_create_netdev calls the cleanup call
of the given profile without checking if it exists, fix that.
Currently the VF reps don't register that callback and we crash
if getting into error -- can be reproduced by the user doing ctrl^C
while attempting to change the sriov mode from legacy to switchdev.
Fixes: 26e59d8077a3 '(net/mlx5e: Implement mlx5e interface attach/detach callbacks')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Sabrina Dubroca <sdubroca@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Currently the firmware API is partial and allows to offload only
the dscp part of the tos, also, ipv6 support isn't there yet.
As such, remove the offloading option of ipv4 dscp till the FW
APIs are more comprehensive.
Fixes: d79b6df6b10a ('net/mlx5e: Add parsing of TC pedit actions to HW format')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Currently we don't check that the link type is Eth and hence crash
on IB ports when attempting to deref esw->xxx, fix that.
To avoid repeating this check over and over, put the existing
checks and the one on link type in a single helper.
Fixes: 7768d1971de6 ('net/mlx5: E-Switch, Add control for encapsulation')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Mohamad Badarnah <mohamadb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The offending commit only changed the code path for PF/VF, but it
didn't take care of VF representors. As a result, since
params->tx_min_inline_mode for VF representors is kzalloced to 0
(MLX5_INLINE_MODE_NONE), all VF reps SQs were set to that mode.
This actually works on CX5 by default but broke CX4. Fix that by
adding a call to query the min inline mode from the VF rep build up code.
Fixes: a6f402e49901 ("net/mlx5e: Tx, no inline copy on ConnectX-5")
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Misuse of (BIT) macro caused to report wrong flags for
"Hardware Transmit Timestamp Modes" and "Hardware Receive
Filter Modes"
Fixes: ef9814deafd0 ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: Maor Dickman <maord@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | |/ / /
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Before attempting to initialize the command interface we must wait till
the fw_initializing bit is clear.
If we fail to meet this condition the hardware will drop our
configuration, specifically the descriptors page address. This scenario
can happen when the firmware is still executing an FLR flow and did not
finish yet so the driver needs to wait for that to finish.
Fixes: e3297246c2c8 ('net/mlx5_core: Wait for FW readiness on startup')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The referenced file dsa.txt is located at
Documentation/devicetree/bindings/net/dsa/dsa.txt
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
In sctp_for_each_transport, pos is used to save how many objs it has
dumped. Now it gets the last obj by sctp_transport_get_idx, then gets
the next obj by sctp_transport_get_next.
The issue is that in the meanwhile if some objs in transport hashtable
are removed and the objs nums are less than pos, sctp_transport_get_idx
would return NULL and hti.walker.tbl is NULL as well. At this moment
it should stop hti, instead of continue getting the next obj. Or it
would cause a NULL pointer dereference in sctp_transport_get_next.
This patch is to pass pos + 1 into sctp_transport_get_idx to get the
next obj directly, even if pos > objs nums, it would return NULL and
stop hti.
Fixes: 626d16f50f39 ("sctp: export some apis or variables for sctp_diag and reuse some for proc")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This fixes CVE-2017-7482.
When a kerberos 5 ticket is being decoded so that it can be loaded into an
rxrpc-type key, there are several places in which the length of a
variable-length field is checked to make sure that it's not going to
overrun the available data - but the data is padded to the nearest
four-byte boundary and the code doesn't check for this extra. This could
lead to the size-remaining variable wrapping and the data pointer going
over the end of the buffer.
Fix this by making the various variable-length data checks use the padded
length.
Reported-by: 石磊 <shilei-c@360.cn>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.c.dionne@auristor.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Now when starting the dad work in addrconf_mod_dad_work, if the dad work
is idle and queued, it needs to hold ifa.
The problem is there's one gap in [1], during which if the pending dad work
is removed elsewhere. It will miss to hold ifa, but the dad word is still
idea and queue.
if (!delayed_work_pending(&ifp->dad_work))
in6_ifa_hold(ifp);
<--------------[1]
mod_delayed_work(addrconf_wq, &ifp->dad_work, delay);
An use-after-free issue can be caused by this.
Chen Wei found this issue when WARN_ON(!hlist_unhashed(&ifp->addr_lst)) in
net6_ifa_finish_destroy was hit because of it.
As Hannes' suggestion, this patch is to fix it by holding ifa first in
addrconf_mod_dad_work, then calling mod_delayed_work and putting ifa if
the dad_work is already in queue.
Note that this patch did not choose to fix it with:
if (!mod_delayed_work(delay))
in6_ifa_hold(ifp);
As with it, when delay == 0, dad_work would be scheduled immediately, all
addrconf_mod_dad_work(0) callings had to be moved under ifp->lock.
Reported-by: Wei Chen <weichen@redhat.com>
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull more pin control fixes from Linus Walleij:
"Some late arriving fixes. I should have sent earlier, just swamped
with work as usual. Thomas patch makes AMD systems usable despite
firmware bugs so it is fairly important.
- Make the AMD driver use a regular interrupt rather than a chained
one, so the system does not lock up.
- Fix a function call error deep inside the STM32 driver"
* tag 'pinctrl-v4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: stm32: Fix bad function call
pinctrl/amd: Use regular interrupt instead of chained
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
In stm32_pconf_parse_conf function, stm32_pmx_gpio_set_direction is
called with wrong parameter value. Indeed, using NULL value for range
will raise an oops.
Fixes: aceb16dc2da5 ("pinctrl: Add STM32 MCUs support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The AMD pinctrl driver uses a chained interrupt to demultiplex the GPIO
interrupts. Kevin Vandeventer reported, that his new AMD Ryzen locks up
hard on boot when the AMD pinctrl driver is initialized. The reason is an
interrupt storm. It's not clear whether that's caused by hardware or
firmware or both.
Using chained interrupts on X86 is a dangerous endavour. If a system is
misconfigured or the hardware buggy there is no safety net to catch an
interrupt storm.
Convert the driver to use a regular interrupt for the demultiplex
handler. This allows the interrupt storm detector to catch the malfunction
and lets the system boot up.
This should be backported to stable because it's likely that more users run
into this problem as the AMD Ryzen machines are spreading.
Reported-by: Kevin Vandeventer
Link: https://bugzilla.suse.com/show_bug.cgi?id=1034261
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |\ \ \ \ \
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- revert of a commit to magicmouse driver that regressess certain
devices, from Daniel Stone
- quirk for a specific Dell mouse, from Sebastian Parschauer
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
Revert "HID: magicmouse: Set multi-touch keybits for Magic Mouse"
HID: Add quirk for Dell PIXART OEM mouse
|
| | |\ \ \ \ \ |
|