summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* irqchip/gic-v3-its: Add VPE schedulingMarc Zyngier2017-08-312-0/+143
| | | | | | | | | | | | | When a VPE is scheduled to run, the corresponding redistributor must be told so, by setting VPROPBASER to the VM's property table, and VPENDBASER to the vcpu's pending table. When scheduled out, we preserve the IDAI and PendingLast bits. The latter is specially important, as it tells the hypervisor that there are pending interrupts for this vcpu. Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Add VPENDBASER/VPROPBASER accessorsMarc Zyngier2017-08-313-0/+38
| | | | | | | | | | V{PEND,PROP}BASER being 64bit registers, they need some ad-hoc accessors on 32bit, specially given that VPENDBASER contains a Valid bit, making the access a bit convoluted. Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Add VPE irq domain [de]activationMarc Zyngier2017-08-311-0/+102
| | | | | | | | | On activation, a VPE is mapped using the VMAPP command, followed by a VINVALL for a good measure. On deactivation, the VPE is simply unmapped. Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Add VPE irq domain allocation/teardownMarc Zyngier2017-08-311-0/+169
| | | | | | | | | | | | | | When creating a VM, the low level GICv4 code is responsible for: - allocating each VPE a unique VPEID - allocating a doorbell interrupt for each VPE - allocating the pending tables for each VPE - allocating the property table for the VM This of course has to be reversed when the VM is brought down. All of this is wired into the irq domain alloc/free methods. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Add VPE domain infrastructureMarc Zyngier2017-08-311-1/+30
| | | | | | | | | Add the basic GICv4 VPE (vcpu in GICv4 parlance) infrastructure (irqchip, irq domain) that is going to be populated in the following patches. Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Add VLPI configuration handlingMarc Zyngier2017-08-311-5/+70
| | | | | | | | | | | | | When a VLPI is reconfigured (enabled, disabled, change in priority), the full configuration byte must be written, and the caches invalidated. Also, when using the irq_mask/irq_unmask methods, it is necessary to disable the doorbell for that particular interrupt (by mapping it to 1023) on top of clearing the Enable bit. Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Add VLPI map/unmap operationsMarc Zyngier2017-08-311-3/+247
| | | | | | | | | | | | | In order to let a VLPI being injected into a guest, the VLPI must be mapped using the VMAPTI command. When moved to a different vcpu, it must be moved with the VMOVI command. These commands are issued via the irq_set_vcpu_affinity method, making sure we unmap the corresponding host LPI first. The reverse is also done when the VLPI is unmapped from the guest. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Add VLPI configuration hookMarc Zyngier2017-08-311-0/+24
| | | | | | | | Add the skeleton irq_set_vcpu_affinity method that will be used to configure VLPIs. Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Add GICv4 ITS command definitionsMarc Zyngier2017-08-312-1/+13
| | | | | | | | | Add the new GICv4 ITS command definitions, most of them, being defined in terms of their physical counterparts. Reviewed-by: Eric Auger <eric.auger@redhat.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v4: Add management structure definitionsMarc Zyngier2017-08-311-0/+92
| | | | | | | | Add a bunch of GICv4-specific data structures that will get used in subsequent patches. Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Generalize LPI configurationMarc Zyngier2017-08-231-10/+11
| | | | | | | | | | | | | | We're are going to need to change a bit more than just the enable bit in the LPI property table in the future. So let's change the LPI configuration funtion to take a set of bits to be cleared, and a set of bits to be set. This way, we'll be able to use it when a guest updates an LPI property (priority, for example). Reviewed-by: Eric Auger <eric.auger@redhat.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Generalize device table allocationMarc Zyngier2017-08-231-10/+16
| | | | | | | | | | As we want to use 2-level tables for VCPUs, let's hack the device table allocator in order to make it slightly more generic. It will get reused in subsequent patches. Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Rework LPI freeingMarc Zyngier2017-08-231-6/+7
| | | | | | | | | Rework LPI deallocation so that it can be reused by the v4 support code. Reviewed-by: Eric Auger <eric.auger@redhat.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Split out pending table allocationMarc Zyngier2017-08-231-9/+20
| | | | | | | | | Just as for the property table, let's move the pending table allocation to a separate function. Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Allow use of indirect VCPU tablesMarc Zyngier2017-08-231-8/+17
| | | | | | | | | The VCPU tables can be quite sparse as well, and it makes sense to use indirect tables as well if possible. Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Split out property table allocationMarc Zyngier2017-08-231-10/+21
| | | | | | | | | | Move the LPI property table allocation into its own function, as this is going to be required for those associated with VMs in the future. Reviewed-by: Eric Auger <eric.auger@redhat.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Implement irq_set_irqchip_state for pending stateMarc Zyngier2017-08-231-0/+78
| | | | | | | | | Allow the pending state of an LPI to be set or cleared via irq_set_irqchip_state. Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Macro-ize its_send_single_commandMarc Zyngier2017-08-231-37/+47
| | | | | | | | | | | | | | | | | | | | Most ITS commands do operate on a collection object, and require a SYNC command to be performed on that collection in order to guarantee the execution of the first command. With GICv4 ITS, another set of commands perform similar operations on a VPE object, and a VSYNC operations must be executed to guarantee their execution. Given the similarities (post a command, perform a synchronization operation on a sync object), it makes sense to reuse the same mechanism for both class of commands. Let's start with turning its_send_single_command into a huge macro that performs the bulk of the work, and a set of helpers that make this macro usable for the GICv3 ITS commands. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Add probing for VLPI propertiesMarc Zyngier2017-08-232-4/+72
| | | | | | | | | Add the probing code for the ITS VLPI support. This includes configuring the ITS number if not supporting the single VMOVP command feature. Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Move LPI definitions aroundMarc Zyngier2017-08-231-12/+13
| | | | | | | | | | The various LPI definitions are in the middle of the code, and would be better placed at the beginning, given that we're going to use some of them much earlier. Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3: Add VLPI/DirectLPI discoveryMarc Zyngier2017-08-232-1/+26
| | | | | | | | Add helper functions that probe for VLPI and DirectLPI properties. Reviewed-by: Eric Auger <eric.auger@redhat.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3: Add redistributor iteratorMarc Zyngier2017-08-231-22/+47
| | | | | | | | | In order to discover the VLPI properties, we need to iterate over the redistributor regions. As we already have code that does this, let's factor it out and make it slightly more generic. Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* genirq: Let irq_set_vcpu_affinity() iterate over hierarchyMarc Zyngier2017-08-231-2/+12
| | | | | | | | | | | | | When assigning an interrupt to a vcpu, it is not unlikely that the level of the hierarchy implementing irq_set_vcpu_affinity is not the top level (think a generic MSI domain on top of a virtualization aware interrupt controller). In such a case, let's iterate over the hierarchy until we find an irqchip implementing it. Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip: Convert to using %pOF instead of full_nameRob Herring2017-08-2316-56/+50Star
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that we have a custom printf format specifier, convert users of full_name to use %pOF instead. This is preparation to remove storing of the full path string for each node. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Lee Jones <lee@kernel.org> Cc: Stefan Wahren <stefan.wahren@i2se.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Ray Jui <rjui@broadcom.com> Cc: Scott Branden <sbranden@broadcom.com> Cc: bcm-kernel-feedback-list@broadcom.com Cc: Sylvain Lemieux <slemieux.tyco@gmail.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Chen-Yu Tsai <wens@csie.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com> Cc: linux-rpi-kernel@lists.infradead.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-mediatek@lists.infradead.org Cc: linux-tegra@vger.kernel.org Acked-by: Eric Anholt <eric@anholt.net> Acked-by: Baruch Siach <baruch@tkos.co.il> Acked-by: Vladimir Zapolskiy <vz@mleia.com> Acked-by: Matthias Brugger <matthias.bgg@gmail.com> Acked-by: Alexandre Torgue <alexandre.torgue@st.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip: Add UniPhier AIDET irqchip driverMasahiro Yamada2017-08-235-0/+303
| | | | | | | | | | | UniPhier SoCs contain AIDET (ARM Interrupt Detector). This is intended to provide additional features that are not covered by GIC. The main purpose is to provide logic inverter to support low level and falling edge trigger types for interrupt lines from on-board devices. Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/gic-v3-its: Properly handle command queue wrappingMarc Zyngier2017-08-191-1/+7
| | | | | | | | | | | | | wait_for_range_completion() is nicely busted when handling wrapping of the command queue, leading to an early exit instead of waiting for the command to have been executed. Fortunately, the impact is pretty minor, as it only impair the detection of an ITS that doesn't make any forward progress for a whole second. And an ITS should *never* lock up. Reported-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* irqchip/armada-370-xp: Enable MSI-X supportStefan Roese2017-08-181-1/+1
| | | | | | | | | | | | | | | | | Armada XP does not only support MSI, but also MSI-X. This patch sets the MSI_FLAG_PCI_MSIX flag in the interrupt controller driver which is the only change necessary to enable MSI-X support on this SoC. As the Linux PCI MSI-X infrastructure takes care of writing the data and address structures into the BAR specified by the MSI-X controller. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* Linux 4.13-rc5Linus Torvalds2017-08-141-1/+1
|
* Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds2017-08-1414-42/+137
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull MIPS fixes from Ralf Baechle: "Another round of MIPS fixes: - compressed boot: Ignore a generated .c file - VDSO: Fix a register clobber list - DECstation: Fix an int-handler.S CPU_DADDI_WORKAROUNDS regression - Octeon: Fix recent cleanups that cleaned away a bit too much thus breaking the arch side of the EDAC and USB drivers. - uasm: Fix duplicate const in "const struct foo const bar[]" which GCC 7.1 no longer accepts. - Fix race on setting and getting cpu_online_mask - Fix preemption issue. To do so cleanly introduce macro to get the size of L3 cache line. - Revert include cleanup that sometimes results in build error - MicroMIPS uses bit 0 of the PC to indicate microMIPS mode. Make sure this bit is set for kernel entry as well. - Prevent configuring the kernel for both microMIPS and MT. There are no such CPUs currently and thus the combination is unsupported and results in build errors. This has been sitting in linux-next for a few days and has survived automated testing by Imagination's test farm. No known regressions pending except a number of issues that crept up due to lots of people switching to GCC 7.1" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: MIPS: Set ISA bit in entry-y for microMIPS kernels MIPS: Prevent building MT support for microMIPS kernels MIPS: PCI: Fix smp_processor_id() in preemptible MIPS: Introduce cpu_tcache_line_size MIPS: DEC: Fix an int-handler.S CPU_DADDI_WORKAROUNDS regression MIPS: VDSO: Fix clobber lists in fallback code paths Revert "MIPS: Don't unnecessarily include kmalloc.h into <asm/cache.h>." MIPS: OCTEON: Fix USB platform code breakage. MIPS: Octeon: Fix broken EDAC driver. MIPS: gitignore: ignore generated .c files MIPS: Fix race on setting and getting cpu_online_mask MIPS: mm: remove duplicate "const" qualifier on insn_table
| * MIPS: Set ISA bit in entry-y for microMIPS kernelsPaul Burton2017-08-081-1/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When building a kernel for the microMIPS ISA, ensure that the ISA bit (ie. bit 0) in the entry address is set. Otherwise we may include an entry address in images which bootloaders will jump to as MIPS32 code. I originally tried using "objdump -f" to obtain the entry address, which works for microMIPS but it always outputs a 32 bit address for a 32 bit ELF whilst nm will sign extend to 64 bit. That matters for systems where we might want to run a MIPS32 kernel on a MIPS64 CPU & load it with a MIPS64 bootloader, which would then jump to a non-canonical (non-sign-extended) address. This works in all cases as it only changes the behaviour for microMIPS kernels, but isn't the prettiest solution. A possible alternative would be to write a custom tool to just extract, sign extend & print the entry point of an ELF executable. I'm open to feedback if that would be preferred. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/16950/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: Prevent building MT support for microMIPS kernelsPaul Burton2017-08-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We don't currently support the MT ASE for microMIPS kernels, and there are no CPUs currently in existence that use both. They can however both be enabled in Kconfig, resulting in build failures such as: AS arch/mips/kernel/cps-vec.o arch/mips/kernel/cps-vec.S: Assembler messages: arch/mips/kernel/cps-vec.S:242: Warning: the 32-bit microMIPS architecture does not support the `mt' extension arch/mips/kernel/cps-vec.S:276: Error: unrecognized opcode `mttc0 $13,$2,2' arch/mips/kernel/cps-vec.S:282: Error: unrecognized opcode `mttc0 $8,$1,2' arch/mips/kernel/cps-vec.S:285: Error: unrecognized opcode `mttc0 $0,$2,1' ... Fix this by preventing MT from being enabled when targeting microMIPS. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/16951/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: PCI: Fix smp_processor_id() in preemptibleMatt Redfearn2017-08-081-4/+3Star
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 1c3c5eab1715 ("sched/core: Enable might_sleep() and smp_processor_id() checks early") enables checks for might_sleep() and smp_processor_id() being used in preemptible code earlier in the boot than before. This results in a new BUG from pcibios_set_cache_line_size(). BUG: using smp_processor_id() in preemptible [00000000] code: swapper/0/1 caller is pcibios_set_cache_line_size+0x10/0x70 CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.13.0-rc1-00007-g3ce3e4ba4275 #615 Stack: 0000000000000000 ffffffff81189694 0000000000000000 ffffffff81822318 000000000000004e 0000000000000001 800000000e20bd08 20c49ba5e3540000 0000000000000000 0000000000000000 ffffffff818d0000 0000000000000000 0000000000000000 ffffffff81189328 ffffffff818ce692 0000000000000000 0000000000000000 ffffffff81189bc8 ffffffff818d0000 0000000000000000 ffffffff81828907 ffffffff81769970 800000020ec78d80 ffffffff818c7b48 0000000000000001 0000000000000001 ffffffff818652b0 ffffffff81896268 ffffffff818c0000 800000020ec7fb40 800000020ec7fc58 ffffffff81684cac 0000000000000000 ffffffff8118ab50 0000000000000030 ffffffff81769970 0000000000000001 ffffffff81122a58 0000000000000000 0000000000000000 ... Call Trace: [<ffffffff81122a58>] show_stack+0x90/0xb0 [<ffffffff81684cac>] dump_stack+0xac/0xf0 [<ffffffff813f7050>] check_preemption_disabled+0x120/0x128 [<ffffffff818855e8>] pcibios_set_cache_line_size+0x10/0x70 [<ffffffff81100578>] do_one_initcall+0x48/0x140 [<ffffffff81865dc4>] kernel_init_freeable+0x194/0x24c [<ffffffff8169c534>] kernel_init+0x14/0x118 [<ffffffff8111ca84>] ret_from_kernel_thread+0x14/0x1c Fix this by using the cpu_*cache_line_size() macros instead. These macros are the "proper" way to determine the CPU cache sizes. This makes use of the newly added cpu_tcache_line_size. Fixes: 1c3c5eab1715 ("sched/core: Enable might_sleep() and smp_processor_id() checks early") Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Suggested-by: James Hogan <james.hogan@imgtec.com> Reviewed-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: Introduce cpu_tcache_line_sizeMatt Redfearn2017-08-081-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There exist macros to return the cache line size of the L1 dcache and L2 scache but there is currently no macro for the L3 tcache. Add this macro which will be used by the following patch "MIPS: PCI: Fix smp_processor_id() in preemptible" Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Maciej W. Rozycki <macro@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/16871/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: DEC: Fix an int-handler.S CPU_DADDI_WORKAROUNDS regressionMaciej W. Rozycki2017-08-071-28/+6Star
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix a commit 3021773c7c3e ("MIPS: DEC: Avoid la pseudo-instruction in delay slots") regression and remove assembly errors: arch/mips/dec/int-handler.S: Assembler messages: arch/mips/dec/int-handler.S:162: Error: Macro used $at after ".set noat" arch/mips/dec/int-handler.S:163: Error: Macro used $at after ".set noat" arch/mips/dec/int-handler.S:229: Error: Macro used $at after ".set noat" arch/mips/dec/int-handler.S:230: Error: Macro used $at after ".set noat" triggering with with the CPU_DADDI_WORKAROUNDS option set and the DADDIU instruction. This is because with that option in place the instruction becomes a macro, which expands to an LI/DADDU (or actually ADDIU/DADDU) sequence that uses $at as a temporary register. With CPU_DADDI_WORKAROUNDS we only support `-msym32' compilation though, and this is already enforced in arch/mips/Makefile, so choose the 32-bit expansion variant for the supported configurations and then replace the 64-bit variant with #error just in case. Fixes: 3021773c7c3e ("MIPS: DEC: Avoid la pseudo-instruction in delay slots") Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: stable@vger.kernel.org # 4.8+ Patchwork: https://patchwork.linux-mips.org/patch/16893/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: VDSO: Fix clobber lists in fallback code pathsGoran Ferenc2017-08-071-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Extend clobber lists to include all GP registers. Fixes: 0b523a85e134 ("MIPS: VDSO: Add implementation of gettimeofday() fallback") Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com> Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com> Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com> Reviewed-by: James Hogan <james.hogan@imgtec.com> Cc: Bo Hu <bohu@google.com> Cc: Douglas Leung <douglas.leung@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Jin Qian <jinqian@google.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Petar Jovanovic <petar.jovanovic@imgtec.com> Cc: Raghu Gandham <raghu.gandham@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/16879/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * Revert "MIPS: Don't unnecessarily include kmalloc.h into <asm/cache.h>."Paul Burton2017-08-071-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 296e46db0073 ("MIPS: Don't unnecessarily include kmalloc.h into <asm/cache.h>.") claimed that the inclusion of the machine's kmalloc.h from asm/cache.h is unnecessary, but this is not true. Without including kmalloc.h we don't get a definition for ARCH_DMA_MINALIGN, which means we no longer suitably align DMA. Further to this the definition of ARCH_KMALLOC_MINALIGN provided by linux/slab.h ends up being set to the alignment of an unsigned long long value rather than to ARCH_DMA_MINALIGN, which means that buffers allocated using kmalloc may no longer be safely aligned for use with DMA. Fix this by re-adding the include of kmalloc.h in asm/cache.h. This reverts commit 296e46db0073 ("MIPS: Don't unnecessarily include kmalloc.h into <asm/cache.h>.") Signed-off-by: Paul Burton <paul.burton@imgtec.com> Fixes: 296e46db0073 ("MIPS: Don't unnecessarily include kmalloc.h into <asm/cache.h>.") Cc: linux-mips@linux-mips.org Cc: stable <stable@vger.kernel.org> # v4.12+ Patchwork: https://patchwork.linux-mips.org/patch/16895/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: OCTEON: Fix USB platform code breakage.Steven J. Hill2017-08-071-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix build error when CONFIG_SMP is turned off: CC [M] arch/mips/cavium-octeon/octeon-usb.o arch/mips/cavium-octeon/octeon-usb.c: In function ‘dwc3_octeon_device_init’: arch/mips/cavium-octeon/octeon-usb.c:540:4: error: implicit declaration of function ‘devm_iounmap’ [-Werror=implicit-function-declaration] devm_iounmap(&pdev->dev, base); Signed-off-by: Steven J. Hill <steven.hill@cavium.com> Reviewed-by: James Hogan <james.hogan@imgtec.com> Tested-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/16907/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: Octeon: Fix broken EDAC driver.Steven J. Hill2017-08-073-1/+97
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit "MIPS: Octeon: Remove unused L2C types and macros." broke the the EDAC driver. Bring back 'cvmx-l2d-defs.h' file and the missing types for L2C. Fixes: 15f6847923a8 ("MIPS: Octeon: Remove unused L2C types and macros.") Fixes: 15f6847923a8 ("MIPS: Octeon: Remove unused L2C types and macros.") Signed-off-by: Steven J. Hill <steven.hill@cavium.com> Reviewed-by: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 4.12+ Patchwork: https://patchwork.linux-mips.org/patch/16906/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: gitignore: ignore generated .c filesBartosz Golaszewski2017-08-071-0/+2
| | | | | | | | | | | | | | | | | | | | | | Add ashldi3.c and bswapsi.c to the list of ignored files. Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl> Reviewed-by: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/16905/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: Fix race on setting and getting cpu_online_maskMatija Glavinic Pecotic2017-08-071-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While testing cpu hoptlug (cpu down and up in loops) on kernel 4.4, it was observed that occasionally check for cpu online will fail in kernel/cpu.c, _cpu_up: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable.git/tree/kernel/cpu.c?h=v4.4.79#n485 518 /* Arch-specific enabling code. */ 519 ret = __cpu_up(cpu, idle); 520 521 if (ret != 0) 522 goto out_notify; 523 BUG_ON(!cpu_online(cpu)); Reason is race between start_secondary and _cpu_up. cpu_callin_map is set before cpu_online_mask. In __cpu_up, cpu_callin_map is waited for, but cpu online mask is not, resulting in race in which secondary processor started and set cpu_callin_map, but not yet set the online mask,resulting in above BUG being hit. Upstream differs in the area. cpu_online check is in bringup_wait_for_ap, which is after cpu reached AP_ONLINE_IDLE,where secondary passed its start function. Nonetheless, fix makes start_secondary safe and not depending on other locks throughout the code. It protects as well against cpu_online checks put in between sometimes in the future. Fix this by moving completion after all flags are set. Signed-off-by: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nokia.com> Cc: Alexander Sverdlin <alexander.sverdlin@nokia.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/16925/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: mm: remove duplicate "const" qualifier on insn_tableThomas Petazzoni2017-08-071-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes the following gcc 7.x build error: arch/mips/mm/uasm-mips.c:51:26: error: duplicate ‘const’ declaration specifier [-Werror=duplicate-decl-specifier] static const struct insn const insn_table[insn_invalid] = { Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Fixes: ce807d5f67ed ("MIPS: Optimize uasm insn lookup.") Cc: David Daney <david.daney@cavium.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/16926/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* | Merge tag 'driver-core-4.13-rc5' of ↵Linus Torvalds2017-08-131-15/+34
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core fixes from Greg KH: "Here are three firmware core fixes for 4.13-rc5. All three of these fix reported issues and have been floating around for a few weeks. They have been in linux-next with no reported problems" * tag 'driver-core-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: firmware: avoid invalid fallback aborts by using killable wait firmware: fix batched requests - send wake up on failure on direct lookups firmware: fix batched requests - wake all waiters
| * | firmware: avoid invalid fallback aborts by using killable waitLuis R. Rodriguez2017-08-101-2/+1Star
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 0cb64249ca500 ("firmware_loader: abort request if wait_for_completion is interrupted") added via 4.0 added support to abort the fallback mechanism when a signal was detected and wait_for_completion_interruptible() returned -ERESTARTSYS -- for instance when a user hits CTRL-C. The abort was overly *too* effective. When a child process terminates (successful or not) the signal SIGCHLD can be sent to the parent process which ran the child in the background and later triggered a sync request for firmware through a sysfs interface which relies on the fallback mechanism. This signal in turn can be recieved by the interruptible wait we constructed on firmware_class and detects it as an abort *before* userspace could get a chance to write the firmware. Upon failure -EAGAIN is returned, so userspace is also kept in the dark about exactly what happened. We can reproduce the issue with the fw_fallback.sh selftest: Before this patch: $ sudo tools/testing/selftests/firmware/fw_fallback.sh ... tools/testing/selftests/firmware/fw_fallback.sh: error - sync firmware request cancelled due to SIGCHLD After this patch: $ sudo tools/testing/selftests/firmware/fw_fallback.sh ... tools/testing/selftests/firmware/fw_fallback.sh: SIGCHLD on sync ignored as expected Fix this by making the wait killable -- only killable by SIGKILL (kill -9). We loose the ability to allow userspace to cancel a write with CTRL-C (SIGINT), however its been decided the compromise to require SIGKILL is worth the gains. Chances of this issue occuring are low due to the number of drivers upstream exclusively relying on the fallback mechanism for firmware (2 drivers), however this is observed in the field with custom drivers with sysfs triggers to load firmware. Only distributions relying on the fallback mechanism are impacted as well. An example reported issue was on Android, as follows: 1) Android init (pid=1) fork()s (say pid=42) [this child process is totally unrelated to firmware loading, it could be sleep 2; for all we care ] 2) Android init (pid=1) does a write() on a (driver custom) sysfs file which ends up calling request_firmware() kernel side 3) The firmware loading fallback mechanism is used, the request is sent to userspace and pid 1 waits in the kernel on wait_* 4) before firmware loading completes pid 42 dies (for any reason, even normal termination) 5) Kernel delivers SIGCHLD to pid=1 to tell it a child has died, which causes -ERESTARTSYS to be returned from wait_* 6) The kernel's wait aborts and return -EAGAIN for the request_firmware() caller. Cc: stable <stable@vger.kernel.org> # 4.0 Fixes: 0cb64249ca500 ("firmware_loader: abort request if wait_for_completion is interrupted") Suggested-by: "Eric W. Biederman" <ebiederm@xmission.com> Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Tested-by: Martin Fuzzey <mfuzzey@parkeon.com> Reported-by: Martin Fuzzey <mfuzzey@parkeon.com> Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | firmware: fix batched requests - send wake up on failure on direct lookupsLuis R. Rodriguez2017-08-101-8/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix batched requests from waiting forever on failure. The firmware API batched requests feature has been broken since the API call request_firmware_direct() was introduced on commit bba3a87e982ad ("firmware: Introduce request_firmware_direct()"), added on v3.14 *iff* the firmware being requested was not present in *certain kernel builds* [0]. When no firmware is found the worker which goes on to finish never informs waiters queued up of this, so any batched request will stall in what seems to be forever (MAX_SCHEDULE_TIMEOUT). Sadly, a reboot will also stall, as the reboot notifier was only designed to kill custom fallback workers. The issue seems to the user as a type of soft lockup, what *actually* happens underneath the hood is a wait call which never completes as we failed to issue a completion on error. For device drivers with optional firmware schemes (ie, Intel iwlwifi, or Netronome -- even though it uses request_firmware() and not request_firmware_direct()), this could mean that when you boot a system with multiple cards the firmware will seem to never load on the system, or that the card is just not responsive even the driver initialization. Due to differences in scheduling possible this should not always trigger -- one would need to to ensure that multiple requests are in place at the right time for this to work, also release_firmware() must not be called prior to any other incoming request. The complexity may not be worth supporting batched requests in the future given the wait mechanism is only used also for the fallback mechanism. We'll keep it for now and just fix it. Its reported that at least with the Intel WiFi cards on one system this issue was creeping up 50% of the boots [0]. Before this commit batched requests testing revealed: ============================================================================ CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n CONFIG_FW_LOADER_USER_HELPER=y Most common Linux distribution setup. API-type no-firmware-found firmware-found ---------------------------------------------------------------------- request_firmware() FAIL OK request_firmware_direct() FAIL OK request_firmware_nowait(uevent=true) FAIL OK request_firmware_nowait(uevent=false) FAIL OK ============================================================================ CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n CONFIG_FW_LOADER_USER_HELPER=n Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare. API-type no-firmware-found firmware-found ---------------------------------------------------------------------- request_firmware() FAIL OK request_firmware_direct() FAIL OK request_firmware_nowait(uevent=true) FAIL OK request_firmware_nowait(uevent=false) FAIL OK ============================================================================ CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y CONFIG_FW_LOADER_USER_HELPER=y Google Android setup. API-type no-firmware-found firmware-found ---------------------------------------------------------------------- request_firmware() OK OK request_firmware_direct() FAIL OK request_firmware_nowait(uevent=true) OK OK request_firmware_nowait(uevent=false) OK OK ============================================================================ Ater this commit batched testing results: ============================================================================ CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n CONFIG_FW_LOADER_USER_HELPER=y Most common Linux distribution setup. API-type no-firmware-found firmware-found ---------------------------------------------------------------------- request_firmware() OK OK request_firmware_direct() OK OK request_firmware_nowait(uevent=true) OK OK request_firmware_nowait(uevent=false) OK OK ============================================================================ CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n CONFIG_FW_LOADER_USER_HELPER=n Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare. API-type no-firmware-found firmware-found ---------------------------------------------------------------------- request_firmware() OK OK request_firmware_direct() OK OK request_firmware_nowait(uevent=true) OK OK request_firmware_nowait(uevent=false) OK OK ============================================================================ CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y CONFIG_FW_LOADER_USER_HELPER=y Google Android setup. API-type no-firmware-found firmware-found ---------------------------------------------------------------------- request_firmware() OK OK request_firmware_direct() OK OK request_firmware_nowait(uevent=true) OK OK request_firmware_nowait(uevent=false) OK OK ============================================================================ [0] https://bugzilla.kernel.org/show_bug.cgi?id=195477 Cc: stable <stable@vger.kernel.org> # v3.14 Fixes: bba3a87e982ad ("firmware: Introduce request_firmware_direct()" Reported-by: Nicolas <nbroeking@me.com> Reported-by: John Ewalt <jewalt@lgsinnovations.com> Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | firmware: fix batched requests - wake all waitersLuis R. Rodriguez2017-08-101-7/+5Star
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The firmware cache mechanism serves two purposes, the secondary purpose is not well documented nor understood. This fixes a regression with the secondary purpose of the firmware cache mechanism: batched requests on successful lookups. Without this fix *any* time a batched request is triggered, secondary requests for which the batched request mechanism was designed for will seem to last forver and seem to never return. This issue is present for all kernel builds possible, and a hard reset is required. The firmware cache is used for: 1) Addressing races with file lookups during the suspend/resume cycle by keeping firmware in memory during the suspend/resume cycle 2) Batched requests for the same file rely only on work from the first file lookup, which keeps the firmware in memory until the last release_firmware() is called Batched requests *only* take effect if secondary requests come in prior to the first user calling release_firmware(). The devres name used for the internal firmware cache is used as a hint other pending requests are ongoing, the firmware buffer data is kept in memory until the last user of the buffer calls release_firmware(), therefore serializing requests and delaying the release until all requests are done. Batched requests wait for a wakup or signal so we can rely on the first file fetch to write to the pending secondary requests. Commit 5b029624948d ("firmware: do not use fw_lock for fw_state protection") ported the firmware API to use swait, and in doing so failed to convert complete_all() to swake_up_all() -- it used swake_up(), loosing the ability for *some* batched requests to take effect. We *could* fix this by just using swake_up_all() *but* swait is now known to be very special use case, so its best to just move away from it. So we just go back to using completions as before commit 5b029624948d ("firmware: do not use fw_lock for fw_state protection") given this was using complete_all(). Without this fix it has been reported plugging in two Intel 6260 Wifi cards on a system will end up enumerating the two devices only 50% of the time [0]. The ported swake_up() should have actually handled the case with two devices, however, *if more than two cards are used* the swake_up() would not have sufficed. This change is only part of the required fixes for batched requests. Another fix is provided in the next patch. This particular change should fix the cases where more than three requests with the same firmware name is used, otherwise batched requests will wait for MAX_SCHEDULE_TIMEOUT and just timeout eventually. Below is a summary of tests triggering batched requests on different kernel builds. Before this patch: ============================================================================ CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n CONFIG_FW_LOADER_USER_HELPER=y Most common Linux distribution setup. API-type no-firmware-found firmware-found ---------------------------------------------------------------------- request_firmware() FAIL FAIL request_firmware_direct() FAIL FAIL request_firmware_nowait(uevent=true) FAIL FAIL request_firmware_nowait(uevent=false) FAIL FAIL ============================================================================ CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n CONFIG_FW_LOADER_USER_HELPER=n Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare. API-type no-firmware-found firmware-found ---------------------------------------------------------------------- request_firmware() FAIL FAIL request_firmware_direct() FAIL FAIL request_firmware_nowait(uevent=true) FAIL FAIL request_firmware_nowait(uevent=false) FAIL FAIL ============================================================================ CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y CONFIG_FW_LOADER_USER_HELPER=y Google Android setup. API-type no-firmware-found firmware-found ---------------------------------------------------------------------- request_firmware() FAIL FAIL request_firmware_direct() FAIL FAIL request_firmware_nowait(uevent=true) FAIL FAIL request_firmware_nowait(uevent=false) FAIL FAIL ============================================================================ After this patch: ============================================================================ CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n CONFIG_FW_LOADER_USER_HELPER=y Most common Linux distribution setup. API-type no-firmware-found firmware-found ---------------------------------------------------------------------- request_firmware() FAIL OK request_firmware_direct() FAIL OK request_firmware_nowait(uevent=true) FAIL OK request_firmware_nowait(uevent=false) FAIL OK ============================================================================ CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n CONFIG_FW_LOADER_USER_HELPER=n Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare. API-type no-firmware-found firmware-found ---------------------------------------------------------------------- request_firmware() FAIL OK request_firmware_direct() FAIL OK request_firmware_nowait(uevent=true) FAIL OK request_firmware_nowait(uevent=false) FAIL OK ============================================================================ CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y CONFIG_FW_LOADER_USER_HELPER=y Google Android setup. API-type no-firmware-found firmware-found ---------------------------------------------------------------------- request_firmware() OK OK request_firmware_direct() FAIL OK request_firmware_nowait(uevent=true) OK OK request_firmware_nowait(uevent=false) OK OK ============================================================================ [0] https://bugzilla.kernel.org/show_bug.cgi?id=195477 CC: <stable@vger.kernel.org> [4.10+] Cc: Ming Lei <ming.lei@redhat.com> Fixes: 5b029624948d ("firmware: do not use fw_lock for fw_state protection") Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | | Merge tag 'char-misc-4.13-rc5' of ↵Linus Torvalds2017-08-133-0/+21
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc fixes from Greg KH: "Here are two patches for 4.13-rc5. One is a fix for a reported thunderbolt issue, and the other a fix for an MEI driver issue. Both have been in linux-next with no reported issues" * tag 'char-misc-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: thunderbolt: Do not enumerate more ports from DROM than the controller has mei: exclude device from suspend direct complete optimization
| * | | thunderbolt: Do not enumerate more ports from DROM than the controller hasMika Westerberg2017-08-101-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some Alpine Ridge LP DROMs (there might be others) erroneusly list more ports than the controller actually has. Most probably because DROM of the full Dual/Single port Thunderbolt controller was reused for LP version. The current DROM parser does not check the upper bound thus it leads to crash when sw->ports[] is accessed over bounds: BUG: unable to handle kernel NULL pointer dereference at 00000000000002ec IP: tb_drom_read+0x383/0x890 [thunderbolt] PGD 0 P4D 0 Oops: 0000 [#1] SMP CPU: 3 PID: 12248 Comm: systemd-udevd Not tainted 4.13.0-rc1-next-20170719 #1 Hardware name: LENOVO 20HF000YGE/20HF000YGE, BIOS N1WET32W (1.11 ) 05/23/2017 task: ffff8a293e4bcd80 task.stack: ffffa698027a8000 RIP: 0010:tb_drom_read+0x383/0x890 [thunderbolt] RSP: 0018:ffffa698027ab990 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff8a2940af7800 RCX: 0000000000000000 RDX: ffff8a2940ebb400 RSI: 0000000000000000 RDI: ffffa698027ab9a0 RBP: ffffa698027ab9d0 R08: 0000000000000001 R09: 0000000000000002 R10: ffff8a2940ebb5b0 R11: 0000000000000000 R12: ffff8a293bfa968c R13: 000000000000002c R14: 0000000000000056 R15: 0000000000000056 FS: 00007f0a945a38c0(0000) GS:ffff8a2961580000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000000002ec CR3: 000000043e785000 CR4: 00000000003606e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: tb_switch_add+0x9d/0x730 [thunderbolt] ? tb_switch_alloc+0x3cd/0x4d0 [thunderbolt] icm_start+0x5a/0xa0 [thunderbolt] tb_domain_add+0xc3/0xf0 [thunderbolt] nhi_probe+0x19e/0x310 [thunderbolt] local_pci_probe+0x42/0xa0 pci_device_probe+0x18d/0x1a0 driver_probe_device+0x2ff/0x450 __driver_attach+0xa4/0xe0 ? driver_probe_device+0x450/0x450 bus_for_each_dev+0x6e/0xb0 driver_attach+0x1e/0x20 bus_add_driver+0x1d0/0x270 ? 0xffffffffc0bbb000 driver_register+0x60/0xe0 ? 0xffffffffc0bbb000 __pci_register_driver+0x4c/0x50 nhi_init+0x28/0x1000 [thunderbolt] do_one_initcall+0x50/0x190 ? __vunmap+0x81/0xb0 ? _cond_resched+0x1a/0x50 ? kmem_cache_alloc_trace+0x15f/0x1c0 ? do_init_module+0x27/0x1e9 do_init_module+0x5f/0x1e9 load_module+0x24e7/0x2a60 ? vfs_read+0x115/0x130 SYSC_finit_module+0xfc/0x120 ? SYSC_finit_module+0xfc/0x120 SyS_finit_module+0xe/0x10 do_syscall_64+0x67/0x170 entry_SYSCALL64_slow_path+0x25/0x25 Fix this by making sure we only enumerate DROM port entries the hardware actually has. Reported-by: Christian Kellner <ckellner@redhat.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Lukas Wunner <lukas@wunner.de> Tested-by: Christian Kellner <ckellner@redhat.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | mei: exclude device from suspend direct complete optimizationAlexander Usyskin2017-08-102-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MEI device performs link reset during system suspend sequence. The link reset cannot be performed while device is in runtime suspend state. The resume sequence is bypassed with suspend direct complete optimization,so the optimization should be disabled for mei devices. Fixes: [ 192.940537] Restarting tasks ... [ 192.940610] PGI is not set [ 192.940619] ------------[ cut here ]------------ [ 192.940623] WARNING: CPU: 0 me.c:653 mei_me_pg_exit_sync+0x351/0x360 [ 192.940624] Modules linked in: [ 192.940627] CPU: 0 PID: 1661 Comm: kworker/0:3 Not tainted 4.13.0-rc2+ #2 [ 192.940628] Hardware name: Dell Inc. XPS 13 9343/0TM99H, BIOS A11 12/08/2016 [ 192.940630] Workqueue: pm pm_runtime_work <snip> [ 192.940642] Call Trace: [ 192.940646] ? pci_pme_active+0x1de/0x1f0 [ 192.940649] ? pci_restore_standard_config+0x50/0x50 [ 192.940651] ? kfree+0x172/0x190 [ 192.940653] ? kfree+0x172/0x190 [ 192.940655] ? pci_restore_standard_config+0x50/0x50 [ 192.940663] mei_me_pm_runtime_resume+0x3f/0xc0 [ 192.940665] pci_pm_runtime_resume+0x7a/0xa0 [ 192.940667] __rpm_callback+0xb9/0x1e0 [ 192.940668] ? preempt_count_add+0x6d/0xc0 [ 192.940670] rpm_callback+0x24/0x90 [ 192.940672] ? pci_restore_standard_config+0x50/0x50 [ 192.940674] rpm_resume+0x4e8/0x800 [ 192.940676] pm_runtime_work+0x55/0xb0 [ 192.940678] process_one_work+0x184/0x3e0 [ 192.940680] worker_thread+0x4d/0x3a0 [ 192.940681] ? preempt_count_sub+0x9b/0x100 [ 192.940683] kthread+0x122/0x140 [ 192.940684] ? process_one_work+0x3e0/0x3e0 [ 192.940685] ? __kthread_create_on_node+0x1a0/0x1a0 [ 192.940688] ret_from_fork+0x27/0x40 [ 192.940690] Code: 96 3a 9e ff 48 8b 7d 98 e8 cd 21 58 00 83 bb bc 01 00 00 04 0f 85 40 fe ff ff e9 41 fe ff ff 48 c7 c7 5f 04 99 96 e8 93 6b 9f ff <0f> ff e9 5d fd ff ff e8 33 fe 99 ff 0f 1f 00 0f 1f 44 00 00 55 [ 192.940719] ---[ end trace a86955597774ead8 ]--- [ 192.942540] done. Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reported-by: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | | | Merge tag 'tty-4.13-rc5' of ↵Linus Torvalds2017-08-134-26/+71
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial fixes from Greg KH: "Here are two tty serial driver fixes for 4.13-rc5. One is a revert of a -rc1 patch that turned out to not be a good idea, and the other is a fix for the pl011 serial driver. Both have been in linux-next with no reported issues" * tag 'tty-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: Revert "serial: Delete dead code for CIR serial ports" tty: pl011: fix initialization order of QDF2400 E44
| * | | | Revert "serial: Delete dead code for CIR serial ports"Sean Young2017-08-011-6/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit 1104321a7b3bb670dc614ffa7958c553e7b3b836. The code is not dead at all and breaks winbond-cir. Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled 00:02: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A 00:03: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a CIR port lirc lirc0: lirc_dev: driver ir-lirc-codec (winbond-cir) registered at minor = 0 winbond-cir 00:03: Region 0x2f8-0x2ff already in use! winbond-cir: probe of 00:03 failed with error -16 Signed-off-by: Sean Young <sean@mess.org> Reviewed-by: Matthias Brugger <mbrugger@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3-55-g7522 (git 2.39.0) at 2024-07-11 15:08:54 +0200