| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
| |
Add binding and basic support for the SD/eMMC controller on Amlogic
S905/GXBB devices.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: added nodes for GX, enabled SDIO on P20x]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
|
|
|
|
|
|
| |
Enable both gxbb USB controller and add a 5V regulator for the OTG port
VBUS
Signed-off-by: Brian Kim <brian.kim@hardkernel.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
|
|
|
|
|
|
|
| |
For boards only supporting 10/100 ethernet over a RMII PHY link, add
a separate pinctrl node. By the way, rename the existing node to rgmii
specific naming in all boards dts.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
|
|
|
|
|
|
|
|
| |
Add nodes for i2c bus on gxbb based platforms.
On the OdroidC2 (I2C A) and P200 (I2C B), the pull-up resistor are
present directly on the board. This indicates that these pins are
dedicated to i2c.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
|
|
|
|
|
|
|
| |
Enable the Infrared Remote Controller on boards which have an Infrared
receiver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
|
|
|
|
|
|
| |
Add node for ethernet interface and pinctrl pins.
Enable on odroid-C2 and P20x boards.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
|
|
|
|
|
|
| |
Add DT nodes for additional UARTs (UART B & C in EE domain) and add pins
for all EE domain UARTs.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
|
|
|
|
|
|
|
| |
Update DTS and DTSI files to enable the pin controller. We also now
support the blinking blue LED on the Odroid-C2.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add minimal DT files for the Hardkernel ODROID-C2 board based on the
Amlogic S905/GXBB SoC.
Used the other gxbb boards from Andreas Färber as a starting point.
Cc: Andreas Färber <afaerber@suse.de>
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|