summaryrefslogtreecommitdiffstats
path: root/arch/i386/kernel/io_apic.c
Commit message (Collapse)AuthorAgeFilesLines
* [PATCH] Use delayed disable mode of ioapic edge triggered interruptsEric W. Biederman2006-11-151-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Komuro reports that ISA interrupts do not work after a disable_irq(), causing some PCMCIA drivers to not work, with messages like eth0: Asix AX88190: io 0x300, irq 3, hw_addr xx:xx:xx:xx:xx:xx eth0: found link beat eth0: autonegotiation complete: 100baseT-FD selected eth0: interrupt(s) dropped! eth0: interrupt(s) dropped! eth0: interrupt(s) dropped! ... Linus Torvalds <torvalds@osdl.org> said: "Now, edge-triggered interrupts are a _lot_ harder to mask, because the Intel APIC is an unbelievable piece of sh*t, and has the edge-detect logic _before_ the mask logic, so if a edge happens _while_ the device is masked, you'll never ever see the edge ever again (unmasking will not cause a new edge, so you simply lost the interrupt). So when you "mask" an edge-triggered IRQ, you can't really mask it at all, because if you did that, you'd lose it forever if the IRQ comes in while you masked it. Instead, we're supposed to leave it active, and set a flag, and IF the IRQ comes in, we just remember it, and mask it at that point instead, and then on unmasking, we have to replay it by sending a self-IPI." This trivial patch solves the problem. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Ingo Molnar <mingo@redhat.com> Acked-by: Komuro <komurojun-mbn@nifty.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] htirq: refactor so we only have one function that writes to the chipEric W. Biederman2006-11-091-14/+12Star
| | | | | | | | | | | | | | | | | | | | | This refactoring actually optimizes the code a little by caching the value that we think the device is programmed with instead of reading it back from the hardware. Which simplifies the code a little and should speed things up a bit. This patch introduces the concept of a ht_irq_msg and modifies the architecture read/write routines to update this code. There is a minor consistency fix here as well as x86_64 forgot to initialize the htirq as masked. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Andi Kleen <ak@suse.de> Acked-by: Bryan O'Sullivan <bos@pathscale.com> Cc: <olson@pathscale.com> Cc: Roland Dreier <rolandd@cisco.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* i386: write IO APIC irq routing entries in correct orderLinus Torvalds2006-11-011-3/+23
| | | | | | | | | | | Since the "mask" bit is in the low word, when we write a new entry, we need to write the high word first, before we potentially unmask it. The exception is when we actually want to mask the interrupt, in which case we want to write the low word first to make sure that the high word doesn't change while the interrupt routing is still active. Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* i386: clean up io-apic accessesLinus Torvalds2006-11-011-0/+40
| | | | | | | | | | | | This is preparation for fixing the ordering of the accesses that got broken by the commit cf4c6a2f27f5db810b69dcb1da7f194489e8ff88 when factoring out the "common" io apic routing entry accesses. Move the accessor function (that were only used by io_apic.c) out of a header file, and use proper memory-mapped accesses rather than making up our own "volatile" pointers. Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] genirq: clean up irq-flow-type namingIngo Molnar2006-10-171-7/+10
| | | | | | | | | | | | | Introduce desc->name and eliminate the handle_irq_name() hack. Add set_irq_chip_and_handler_name() to set the flow type and name at once. Signed-off-by: Ingo Molnar <mingo@elte.hu> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Matthew Wilcox <willy@debian.org> Cc: Kyle McMartin <kyle@mcmartin.ca> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] use struct irq_chip instead of struct hw_interrupt_typeAneesh Kumar K.V2006-10-111-1/+1
| | | | | | | | | | hw_interrupt_type is deprecated in favour of struct irq_chip. [mingo@elte.hu: do x86_64 too] Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] i386/x86_64: Remove global IO_APIC_VECTOREric W. Biederman2006-10-081-6/+6
| | | | | | | | | | | | | | Which vector an irq is assigned to now varies dynamically and is not needed outside of io_apic.c. So remove the possibility of accessing the information outside of io_apic.c and remove the silly macro that makes looking for users of irq_vector difficult. The fact this compiles ensures there aren't any more pieces of the old CONFIG_PCI_MSI weirdness that I failed to remove. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] htirq: tidy up the htirq codeEric W. Biederman2006-10-041-3/+2Star
| | | | | | | | | | | | | | | | | | | | | | This moves the declarations for the architecture helpers into include/linux/htirq.h from the generic include/linux/pci.h. Hopefully this will make this distinction clearer. htirq.h is included where it is needed. The dependency on the msi code is fixed and removed. The Makefile is tidied up. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tony Luck <tony.luck@intel.com> Cc: Andi Kleen <ak@suse.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Greg KH <greg@kroah.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] msi: refactor and move the msi irq_chip into the arch codeEric W. Biederman2006-10-041-23/+58
| | | | | | | | | | | | | | | | | | | | | | | | | | | It turns out msi_ops was simply not enough to abstract the architecture specific details of msi. So I have moved the resposibility of constructing the struct irq_chip to the architectures, and have two architecture specific functions arch_setup_msi_irq, and arch_teardown_msi_irq. For simple architectures those functions can do all of the work. For architectures with platform dependencies they can call into the appropriate platform code. With this msi.c is finally free of assuming you have an apic, and this actually takes less code. The helpers for the architecture specific code are declared in the linux/msi.h to keep them separate from the msi functions used by drivers in linux/pci.h Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tony Luck <tony.luck@intel.com> Cc: Andi Kleen <ak@suse.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Greg KH <greg@kroah.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] Initial generic hypertransport interrupt supportEric W. Biederman2006-10-041-0/+90
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch implements two functions ht_create_irq and ht_destroy_irq for use by drivers. Several other functions are implemented as helpers for arch specific irq_chip handlers. The driver for the card I tested this on isn't yet ready to be merged. However this code is and hypertransport irqs are in use in a few other places in the kernel. Not that any of this will get merged before 2.6.19 Because the ipath-ht400 is slightly out of spec this code will need to be generalized to work there. I think all of the powerpc uses are for a plain interrupt controller in a chipset so support for native hypertransport devices is a little less interesting. However I think this is a half way decent model on how to separate arch specific and generic helper code, and I think this is a functional model of how to get the architecture dependencies out of the msi code. [akpm@osdl.org: Kconfig fix] Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Greg KH <greg@kroah.com> Cc: Andi Kleen <ak@muc.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] genirq: i386 irq: Remove the msi assumption that irq == vectorEric W. Biederman2006-10-041-132/+49Star
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch removes the change in behavior of the irq allocation code when CONFIG_PCI_MSI is defined. Removing all instances of the assumption that irq == vector. create_irq is rewritten to first allocate a free irq and then to assign that irq a vector. assign_irq_vector is made static and the AUTO_ASSIGN case which allocates an vector not bound to an irq is removed. The ioapic vector methods are removed, and everything now works with irqs. The definition of NR_IRQS no longer depends on CONFIG_PCI_MSI [akpm@osdl.org: cleanup] Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Rajesh Shah <rajesh.shah@intel.com> Cc: Andi Kleen <ak@muc.de> Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] genirq: i386 irq: Move msi message composition into io_apic.cEric W. Biederman2006-10-041-0/+70
| | | | | | | | | | | | | | | | | | | | | | This removes the hardcoded assumption that irq == vector in the msi composition code, and it allows the msi message composition to setup logical mode, or lowest priorirty delivery mode as we do for other apic interrupts, and with the same selection criteria. Basically this moves the problem of what is in the msi message into the architecture irq management code where it belongs. Not in a generic layer that doesn't have enough information to compose msi messages properly. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Rajesh Shah <rajesh.shah@intel.com> Cc: Andi Kleen <ak@muc.de> Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] genirq: i386 irq: Dynamic irq supportEric W. Biederman2006-10-041-0/+48
| | | | | | | | | | | | | | | | | | The current implementation of create_irq() is a hack but it is the current hack that msi.c uses, and unfortunately the ``generic'' apic msi ops depend on this hack. Thus we are stuck this hack of assuming irq == vector until the depencencies in the generic msi code are removed. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Rajesh Shah <rajesh.shah@intel.com> Cc: Andi Kleen <ak@muc.de> Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] genirq: convert the i386 architecture to irq-chipsIngo Molnar2006-10-041-104/+56Star
| | | | | | | | | | | | | | | This patch converts all the i386 PIC controllers (except VisWS and Voyager, which I could not test - but which should still work as old-style IRQ layers) to the new and simpler irq-chip interrupt handling layer. [akpm@osdl.org: build fix] [mingo@elte.hu: enable fasteoi handler for i386 level-triggered IO-APIC irqs] Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Roland Dreier <rolandd@cisco.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] i386: Replace i386 open-coded cmdline parsing withRusty Russell2006-09-261-1/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch replaces the open-coded early commandline parsing throughout the i386 boot code with the generic mechanism (already used by ppc, powerpc, ia64 and s390). The code was inconsistent with whether it deletes the option from the cmdline or not, meaning some of these will get passed through the environment into init. This transformation is mainly mechanical, but there are some notable parts: 1) Grammar: s/linux never set's it up/linux never sets it up/ 2) Remove hacked-in earlyprintk= option scanning. When someone actually implements CONFIG_EARLY_PRINTK, then they can use early_param(). [AK: actually it is implemented, but I'm adding the early_param it in the next x86-64 patch] 3) Move declaration of generic_apic_probe() from setup.c into asm/apic.h 4) Various parameters now moved into their appropriate files (thanks Andi). 5) All parse functions which examine arg need to check for NULL, except one where it has subtle humor value. AK: readded acpi_sci handling which was completely dropped AK: moved some more variables into acpi/boot.c Cc: len.brown@intel.com Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Andi Kleen <ak@suse.de>
* [PATCH] i386: Factor out common io apic routing entry accessAndi Kleen2006-09-261-57/+43Star
| | | | | | | | | | | | | | | | The IO APIC code had lots of duplicated code to read/write 64bit routing entries into the IO-APIC. Factor this out int common read/write functions In a few cases the IO APIC lock is taken more often now, but this isn't a problem because it's all initialization/shutdown only slow path code. Similar to earlier x86-64 patch. Includes a fix by Jiri Slaby for a mistake that broke resume Signed-off-by: Andi Kleen <ak@suse.de>
* [PATCH] i386: Allow to use GENERICARCH for UP kernelsAndi Kleen2006-09-261-0/+1
| | | | | | | | | | | | There are some machines around (large xSeries or Unisys ES7000) that need physical IO-APIC destination mode to access all of their IO devices. This currently doesn't work in UP kernels as used in distribution installers. This patch allows to compile even UP kernels as GENERICARCH which allows to use physical or clustered APIC mode. Signed-off-by: Andi Kleen <ak@suse.de>
* Remove obsolete #include <linux/config.h>Jörn Engel2006-06-301-1/+0Star
| | | | | Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
* [PATCH] genirq: add ->retrigger() irq op to consolidate hw_irq_resend()Ingo Molnar2006-06-291-0/+9
| | | | | | | | | | | | Add ->retrigger() irq op to consolidate hw_irq_resend() implementations. (Most architectures had it defined to NOP anyway.) NOTE: ia64 needs testing. i386 and x86_64 tested. Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] genirq: cleanup: merge pending_irq_cpumask[] into irq_desc[]Ingo Molnar2006-06-291-1/+1
| | | | | | | | | | Consolidation: remove the pending_irq_cpumask[NR_IRQS] array and move it into the irq_desc[NR_IRQS].pending_mask field. Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] genirq: rename desc->handler to desc->chipIngo Molnar2006-06-291-7/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch-queue improves the generic IRQ layer to be truly generic, by adding various abstractions and features to it, without impacting existing functionality. While the queue can be best described as "fix and improve everything in the generic IRQ layer that we could think of", and thus it consists of many smaller features and lots of cleanups, the one feature that stands out most is the new 'irq chip' abstraction. The irq-chip abstraction is about describing and coding and IRQ controller driver by mapping its raw hardware capabilities [and quirks, if needed] in a straightforward way, without having to think about "IRQ flow" (level/edge/etc.) type of details. This stands in contrast with the current 'irq-type' model of genirq architectures, which 'mixes' raw hardware capabilities with 'flow' details. The patchset supports both types of irq controller designs at once, and converts i386 and x86_64 to the new irq-chip design. As a bonus side-effect of the irq-chip approach, chained interrupt controllers (master/slave PIC constructs, etc.) are now supported by design as well. The end result of this patchset intends to be simpler architecture-level code and more consolidation between architectures. We reused many bits of code and many concepts from Russell King's ARM IRQ layer, the merging of which was one of the motivations for this patchset. This patch: rename desc->handler to desc->chip. Originally i did not want to do this, because it's a big patch. But having both "desc->handler", "desc->handle_irq" and "action->handler" caused a large degree of confusion and made the code appear alot less clean than it truly is. I have also attempted a dual approach as well by introducing a desc->chip alias - but that just wasnt robust enough and broke frequently. So lets get over with this quickly. The conversion was done automatically via scripts and converts all the code in the kernel. This renaming patch is the first one amongst the patches, so that the remaining patches can stay flexible and can be merged and split up without having some big monolithic patch act as a merge barrier. [akpm@osdl.org: build fix] [akpm@osdl.org: another build fix] Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] x86_64: fix vector_lock deadlock in io_apic.cIngo Molnar2006-06-261-4/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix a potential deadlock scenario introduced by io_apic.c's new vector_lock on i386 and x86_64. Found by the locking correctness validator. The patch was boot-tested on x86. For details of the deadlock scenario, see the validator output: ====================================================== [ BUG: hard-safe -> hard-unsafe lock order detected! ] ------------------------------------------------------ idle/1 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire: (msi_lock){....}, at: [<c04ff8d2>] startup_msi_irq_wo_maskbit+0x10/0x35 and this task is already holding: (&irq_desc[i].lock){++..}, at: [<c015b924>] probe_irq_on+0x36/0x107 which would create a new lock dependency: (&irq_desc[i].lock){++..} -> (msi_lock){....} but this new dependency connects a hard-irq-safe lock: (&irq_desc[i].lock){++..} ... which became hard-irq-safe at: [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10485e9>] _spin_lock+0x21/0x2f [<c015aff5>] __do_IRQ+0x3d/0x113 [<c01062d3>] do_IRQ+0x8c/0xad to a hard-irq-unsafe lock: (vector_lock){--..} ... which became hard-irq-unsafe at: ... [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10485e9>] _spin_lock+0x21/0x2f [<c011b5e8>] assign_irq_vector+0x34/0xc8 [<c1aa82fa>] setup_IO_APIC+0x45a/0xcff [<c1aa56e3>] smp_prepare_cpus+0x5ea/0x8aa [<c010033f>] init+0x32/0x2cb [<c0102005>] kernel_thread_helper+0x5/0xb which could potentially lead to deadlocks! other info that might help us debug this: 3 locks held by idle/1: #0: (port_mutex){--..}, at: [<c067070d>] uart_add_one_port+0x61/0x289 #1: (&state->mutex){--..}, at: [<c067071f>] uart_add_one_port+0x73/0x289 #2: (&irq_desc[i].lock){++..}, at: [<c015b924>] probe_irq_on+0x36/0x107 the hard-irq-safe lock's dependencies: -> (&irq_desc[i].lock){++..} ops: 9861 { initial-use at: [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10487f4>] _spin_lock_irqsave+0x2a/0x3a [<c015b415>] setup_irq+0x9b/0x14d [<c1aaa4c4>] time_init_hook+0xf/0x11 [<c1a9f320>] time_init+0x44/0x46 [<c1a9955f>] start_kernel+0x191/0x38f [<c0100210>] 0xc0100210 in-hardirq-W at: [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10485e9>] _spin_lock+0x21/0x2f [<c015aff5>] __do_IRQ+0x3d/0x113 [<c01062d3>] do_IRQ+0x8c/0xad in-softirq-W at: [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10485e9>] _spin_lock+0x21/0x2f [<c015aff5>] __do_IRQ+0x3d/0x113 [<c01062d3>] do_IRQ+0x8c/0xad } ... key at: [<c1ea31e0>] irq_desc_lock_type+0x0/0x20 -> (i8259A_lock){++..} ops: 5149 { initial-use at: [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10487f4>] _spin_lock_irqsave+0x2a/0x3a [<c0108090>] init_8259A+0x11/0x8f [<c1aa0d22>] init_ISA_irqs+0x12/0x4d [<c1aaa4f0>] pre_intr_init_hook+0x8/0xa [<c1aa0cb9>] init_IRQ+0xe/0x65 [<c1a99546>] start_kernel+0x178/0x38f [<c0100210>] 0xc0100210 in-hardirq-W at: [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10487f4>] _spin_lock_irqsave+0x2a/0x3a [<c0107fb0>] mask_and_ack_8259A+0x1b/0xcc [<c015b007>] __do_IRQ+0x4f/0x113 [<c01062d3>] do_IRQ+0x8c/0xad in-softirq-W at: [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10487f4>] _spin_lock_irqsave+0x2a/0x3a [<c0107fb0>] mask_and_ack_8259A+0x1b/0xcc [<c015b007>] __do_IRQ+0x4f/0x113 [<c01062d3>] do_IRQ+0x8c/0xad } ... key at: [<c142f174>] i8259A_lock+0x14/0x40 ... acquired at: [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10487f4>] _spin_lock_irqsave+0x2a/0x3a [<c0107eb2>] enable_8259A_irq+0x10/0x47 [<c0107f12>] startup_8259A_irq+0x8/0xc [<c015b45e>] setup_irq+0xe4/0x14d [<c1aaa4c4>] time_init_hook+0xf/0x11 [<c1a9f320>] time_init+0x44/0x46 [<c1a9955f>] start_kernel+0x191/0x38f [<c0100210>] 0xc0100210 -> (ioapic_lock){+...} ops: 122 { initial-use at: [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10487f4>] _spin_lock_irqsave+0x2a/0x3a [<c1aa71db>] io_apic_get_version+0x16/0x55 [<c1aa5c73>] mp_register_ioapic+0xc6/0x127 [<c1aa382e>] acpi_parse_ioapic+0x2d/0x39 [<c1abe031>] acpi_table_parse_madt_family+0xb4/0x100 [<c1abe093>] acpi_table_parse_madt+0x16/0x18 [<c1aa3c8a>] acpi_boot_init+0x132/0x251 [<c1aa08ea>] setup_arch+0xd36/0xe37 [<c1a99434>] start_kernel+0x66/0x38f [<c0100210>] 0xc0100210 in-hardirq-W at: [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10487f4>] _spin_lock_irqsave+0x2a/0x3a [<c011bce1>] mask_IO_APIC_irq+0x11/0x31 [<c011c5cc>] ack_edge_ioapic_vector+0x31/0x41 [<c015b007>] __do_IRQ+0x4f/0x113 [<c01062d3>] do_IRQ+0x8c/0xad } ... key at: [<c1432514>] ioapic_lock+0x14/0x3c -> (i8259A_lock){++..} ops: 5149 { initial-use at: [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10487f4>] _spin_lock_irqsave+0x2a/0x3a [<c0108090>] init_8259A+0x11/0x8f [<c1aa0d22>] init_ISA_irqs+0x12/0x4d [<c1aaa4f0>] pre_intr_init_hook+0x8/0xa [<c1aa0cb9>] init_IRQ+0xe/0x65 [<c1a99546>] start_kernel+0x178/0x38f [<c0100210>] 0xc0100210 in-hardirq-W at: [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10487f4>] _spin_lock_irqsave+0x2a/0x3a [<c0107fb0>] mask_and_ack_8259A+0x1b/0xcc [<c015b007>] __do_IRQ+0x4f/0x113 [<c01062d3>] do_IRQ+0x8c/0xad in-softirq-W at: [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10487f4>] _spin_lock_irqsave+0x2a/0x3a [<c0107fb0>] mask_and_ack_8259A+0x1b/0xcc [<c015b007>] __do_IRQ+0x4f/0x113 [<c01062d3>] do_IRQ+0x8c/0xad } ... key at: [<c142f174>] i8259A_lock+0x14/0x40 ... acquired at: [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10487f4>] _spin_lock_irqsave+0x2a/0x3a [<c0107e6b>] disable_8259A_irq+0x10/0x47 [<c011bdbd>] startup_edge_ioapic_vector+0x31/0x58 [<c015b45e>] setup_irq+0xe4/0x14d [<c015b5a1>] request_irq+0xda/0xf9 [<c1ac983a>] rtc_init+0x6a/0x1a7 [<c0100457>] init+0x14a/0x2cb [<c0102005>] kernel_thread_helper+0x5/0xb ... acquired at: [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10487f4>] _spin_lock_irqsave+0x2a/0x3a [<c011bce1>] mask_IO_APIC_irq+0x11/0x31 [<c011c5cc>] ack_edge_ioapic_vector+0x31/0x41 [<c015b007>] __do_IRQ+0x4f/0x113 [<c01062d3>] do_IRQ+0x8c/0xad the hard-irq-unsafe lock's dependencies: -> (vector_lock){--..} ops: 31 { initial-use at: [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10485e9>] _spin_lock+0x21/0x2f [<c011b5e8>] assign_irq_vector+0x34/0xc8 [<c1aa82fa>] setup_IO_APIC+0x45a/0xcff [<c1aa56e3>] smp_prepare_cpus+0x5ea/0x8aa [<c010033f>] init+0x32/0x2cb [<c0102005>] kernel_thread_helper+0x5/0xb softirq-on-W at: [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10485e9>] _spin_lock+0x21/0x2f [<c011b5e8>] assign_irq_vector+0x34/0xc8 [<c1aa82fa>] setup_IO_APIC+0x45a/0xcff [<c1aa56e3>] smp_prepare_cpus+0x5ea/0x8aa [<c010033f>] init+0x32/0x2cb [<c0102005>] kernel_thread_helper+0x5/0xb hardirq-on-W at: [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10485e9>] _spin_lock+0x21/0x2f [<c011b5e8>] assign_irq_vector+0x34/0xc8 [<c1aa82fa>] setup_IO_APIC+0x45a/0xcff [<c1aa56e3>] smp_prepare_cpus+0x5ea/0x8aa [<c010033f>] init+0x32/0x2cb [<c0102005>] kernel_thread_helper+0x5/0xb } ... key at: [<c1432574>] vector_lock+0x14/0x3c stack backtrace: [<c0104f36>] show_trace+0xd/0xf [<c010543e>] dump_stack+0x17/0x19 [<c0144e34>] check_usage+0x1f6/0x203 [<c0146395>] __lockdep_acquire+0x8c2/0xaa5 [<c01468c4>] lockdep_acquire+0x68/0x84 [<c10487f4>] _spin_lock_irqsave+0x2a/0x3a [<c04ff8d2>] startup_msi_irq_wo_maskbit+0x10/0x35 [<c015b932>] probe_irq_on+0x44/0x107 [<c0673d58>] serial8250_config_port+0x84b/0x986 [<c06707b1>] uart_add_one_port+0x105/0x289 [<c1ace54b>] serial8250_init+0xc3/0x10a [<c0100457>] init+0x14a/0x2cb [<c0102005>] kernel_thread_helper+0x5/0xb Signed-off-by: Ingo Molnar <mingo@elte.hu> Cc: Jan Beulich <jbeulich@novell.com> Cc: Andi Kleen <ak@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] x86_64: nmi watchdog header cleanupDon Zickus2006-06-261-0/+1
| | | | | | | | Misc header cleanup for nmi watchdog. Signed-off-by: Don Zickus <dzickus@redhat.com> Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] i386/x86-64: simplify ioapic_register_intr()Jan Beulich2006-06-261-15/+8Star
| | | | | | | | Simplify (remove duplication of) code in ioapic_register_intr(). Signed-off-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] x86_64: serialize assign_irq_vector() use of static variablesJan Beulich2006-06-261-6/+18
| | | | | | | | | Since assign_irq_vector() can be called at runtime, its access of static variables should be protected by a lock. Signed-off-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] x86: kernel irq balance doesn't workZhang Yanmin2006-06-231-11/+20
| | | | | | | | | | | | | | | | | | | | | | | | On i386, kernel irq balance doesn't work. 1) In function do_irq_balance, after kernel finds the min_loaded cpu but before calling set_pending_irq to really pin the selected_irq to the target cpu, kernel does a cpus_and with irq_affinity[selected_irq]. Later on, when the irq is acked, kernel would calls move_native_irq=>desc->handler->set_affinity to change the irq affinity. However, every function pointed by hw_interrupt_type->set_affinity(unsigned int irq, cpumask_t cpumask) always changes irq_affinity[irq] to cpumask. Next time when recalling do_irq_balance, it has to do cpu_ands again with irq_affinity[selected_irq], but irq_affinity[selected_irq] already becomes one cpu selected by the first irq balance. 2) Function balance_irq in file arch/i386/kernel/io_apic.c has the same issue. [akpm@osdl.org: cleanups] Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] x86_64: avoid IRQ0 ioapic pin collisionKimball Murray2006-05-081-0/+5
| | | | | | | | | | | | | | | | | | The patch addresses a problem with ACPI SCI interrupt entry, which gets re-used, and the IRQ is assigned to another unrelated device. The patch corrects the code such that SCI IRQ is skipped and duplicate entry is avoided. Second issue came up with VIA chipset, the problem was caused by original patch assigning IRQs starting 16 and up. The VIA chipset uses 4-bit IRQ register for internal interrupt routing, and therefore cannot handle IRQ numbers assigned to its devices. The patch corrects this problem by allowing PCI IRQs below 16. Cc: len.brown@intel.com Signed-off by: Natalie Protasevich <Natalie.Protasevich@unisys.com> Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] Don't pass boot parameters to argv_init[]OGAWA Hirofumi2006-03-311-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The boot cmdline is parsed in parse_early_param() and parse_args(,unknown_bootoption). And __setup() is used in obsolete_checksetup(). start_kernel() -> parse_args() -> unknown_bootoption() -> obsolete_checksetup() If __setup()'s callback (->setup_func()) returns 1 in obsolete_checksetup(), obsolete_checksetup() thinks a parameter was handled. If ->setup_func() returns 0, obsolete_checksetup() tries other ->setup_func(). If all ->setup_func() that matched a parameter returns 0, a parameter is seted to argv_init[]. Then, when runing /sbin/init or init=app, argv_init[] is passed to the app. If the app doesn't ignore those arguments, it will warning and exit. This patch fixes a wrong usage of it, however fixes obvious one only. Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] for_each_possible_cpu: i386KAMEZAWA Hiroyuki2006-03-281-2/+2
| | | | | | | | | | This patch replaces for_each_cpu with for_each_possible_cpu. under arch/i386. Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] more for_each_cpu() conversionsAndrew Morton2006-03-231-13/+9Star
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When we stop allocating percpu memory for not-possible CPUs we must not touch the percpu data for not-possible CPUs at all. The correct way of doing this is to test cpu_possible() or to use for_each_cpu(). This patch is a kernel-wide sweep of all instances of NR_CPUS. I found very few instances of this bug, if any. But the patch converts lots of open-coded test to use the preferred helper macros. Cc: Mikael Starvik <starvik@axis.com> Cc: David Howells <dhowells@redhat.com> Acked-by: Kyle McMartin <kyle@parisc-linux.org> Cc: Anton Blanchard <anton@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mundt <lethal@linux-sh.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: William Lee Irwin III <wli@holomorphy.com> Cc: Andi Kleen <ak@muc.de> Cc: Christian Zankel <chris@zankel.net> Cc: Philippe Elie <phil.el@wanadoo.fr> Cc: Nathan Scott <nathans@sgi.com> Cc: Jens Axboe <axboe@suse.de> Cc: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] x86: deterine xapic using apic versionShaohua Li2006-03-231-1/+2
| | | | | | | | | | | | Checking APIC version instead of CPU family to determine XAPIC. Family 6 CPU could have xapic as well. Signed-off-by: Shaohua Li<shaohua.li@intel.com> Cc: Dave Jones <davej@codemonkey.org.uk> Cc: "Seth, Rohit" <rohit.seth@intel.com> Cc: Andi Kleen <ak@muc.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] i386: port ATI timer fix from x86_64 to i386 IIAndi Kleen2006-03-091-1/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | ATI chipsets tend to generate double timer interrupts for the local APIC timer when both the 8254 and the IO-APIC timer pins are enabled. This is because they route it to both and the result is anded together and the CPU ends up processing it twice. This patch changes check_timer to disable the 8254 routing for interrupt 0. I think it would be safe on all chipsets actually (i tested it on a couple and it worked everywhere) and Windows seems to do it in a similar way, but to be conservative this patch only enables this mode on ATI (and adds options to enable/disable too) Ported over from a similar x86-64 change. I reused the ACPI earlyquirk infrastructure for the ATI bridge check, but tweaked it a bit to work even without ACPI. Inspired by a patch from Chuck Ebbert, but redone. Cc: Chuck Ebbert <76306.1226@compuserve.com> Cc: "Brown, Len" <len.brown@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] i386: Handle non existing APICs without panicingAndreas Deresch2006-02-261-2/+4
| | | | | | | | | | | | [description from AK] This fixes booting in APIC mode on some ACER laptops. x86-64 did a similar change some time ago. See http://bugzilla.kernel.org/show_bug.cgi?id=4700 for details Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] x86_64: Memorize location of i8259 for reboots.Eric W. Biederman2006-01-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently we attempt to restore virtual wire mode on reboot, which only works if we can figure out where the i8259 is connected. This is very useful when we are kexec another kernel and likely helpful to an peculiar BIOS that make assumptions about how the system is setup. Since the acpi MADT table does not provide the location where the i8259 is connected we have to look at the hardware to figure it out. Most systems have the i8259 connected the local apic of the cpu so won't be affected but people running Opteron and some serverworks chipsets should be able to use kexec now. In addition this patch removes the hard coded assumption that the io_apic that delivers isa interrups is always known to the kernel as io_apic 0. There does not appear to be anything to guarantee that assumption is true. And From: Vivek Goyal <vgoyal@in.ibm.com> A minor fix to the patch which remembers the location of where i8259 is connected. Now counter i has been replaced by apic. counter i is having some junk value which was leading to non-detection of i8259 connected to IOAPIC. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com> Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] i386: ioapic virtual wire mode fixVivek Goyal2006-01-061-2/+2
| | | | | | | | | | | | | | | | | | | | | o Currently, during kexec reboot, IOAPIC is re-programmed back to virtual wire mode if there was an i8259 connected to it. This enables getting timer interrupts in second kernel in legacy mode. o After putting into virtual wire mode, IOAPIC delivers the i8259 interrupts to CPU0. This works well for kexec but not for kdump as we might crash on a different CPU and second kernel will not see timer interrupts. o This patch modifies the redirection table entry to deliver the timer interrupts to the cpu we are rebooting (instead of hardcoding to zero). This ensures that second kernel receives timer interrupts even on a non-boot cpu. Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com> Cc: Andi Kleen <ak@muc.de> Cc: "Seth, Rohit" <rohit.seth@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] setting irq affinity is broken in ia32 with MSI enabledShaohua Li2005-11-301-2/+2
| | | | | | | | | | Setting irq affinity stops working when MSI is enabled. With MSI, move_irq is empty, so we can't change irq affinity. It appears a typo in Ashok's original commit for this issue. X86_64 actually is using move_native_irq. Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Revert "i386: move apic init in init_IRQs"Linus Torvalds2005-11-011-5/+1Star
| | | | | | | | Commit f2b36db692b7ff6972320ad9839ae656a3b0ee3e causes a bootup hang on at least one machine. Revert for now until we understand why. The old code may be ugly, but it works. Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] i386: move apic init in init_IRQsEric W. Biederman2005-10-311-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | All kinds of ugliness exists because we don't initialize the apics during init_IRQs. - We calibrate jiffies in non apic mode even when we are using apics. - We have to have special code to initialize the apics when non-smp. - The legacy i8259 must exist and be setup correctly, even when we won't use it past initialization. - The kexec on panic code must restore the state of the io_apics. - init/main.c needs a special case for !smp smp_init on x86 In addition to pure code movement I needed a couple of non-obvious changes: - Move setup_boot_APIC_clock into APIC_late_time_init for simplicity. - Use cpu_khz to generate a better approximation of loops_per_jiffies so I can verify the timer interrupt is working. - Call setup_apic_nmi_watchdog again after cpu_khz is initialized on the boot cpu. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] i386 io_apic.c: Memorize at bootup where the i8259 is connectedEric W. Biederman2005-10-311-35/+112
| | | | | | | | | | | | | | | | | | | | | | Currently we attempt to restore virtual wire mode on reboot, which only works if we can figure out where the i8259 is connected. This is very useful when we kexec another kernel and likely helpful when dealing with a BIOS that make assumptions about how the system is setup. Since the acpi MADT table does not provide the location where the i8259 is connected we have to look at the hardware to figure it out. Most systems have the i8259 connected the local apic of the cpu so won't be affected but people running Opteron and some serverworks chipsets should be able to use kexec now. In addition this patch removes the hard coded assumption that the io_apic that delivers isa interrups is always known to the kernel as io_apic 0. As there does not appear to be anything to guarantee that assumption is true. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] useless includes of linux/irq.h in arch/i386Al Viro2005-09-271-1/+0Star
| | | | | | | | | | Most of these guys are simply not needed (pulled by other stuff via asm-i386/hardirq.h). One that is not entirely useless is hilarious - arch/i386/oprofile/nmi_timer_int.c includes linux/irq.h... as a way to get linux/errno.h Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] x86-64: i386/x86-64: Fix time going twice as fast problem on ATI ↵Chuck Ebbert2005-09-121-0/+4
| | | | | | | | | | | Xpress chipsets Original patch from Bertro Simul This is probably still not quite correct, but seems to be the best solution so far. Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] i386: fix-up schedule_timeout() usageNishanth Aravamudan2005-09-101-2/+1Star
| | | | | | | | | Use schedule_timeout_interruptible() instead of set_current_state()/schedule_timeout() to reduce kernel size. Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] Fix misspelled i8259 typo in io_apic.cKarsten Wiese2005-09-091-2/+2
| | | | | | | | The legacy PIC's name is "i8259". Signed-off-by: Karsten Wiese <annabellesgarden@yahoo.de> Signed-off-by: Vojtech Pavlik <vojtech@suse.cz> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Merge linux-2.6 with linux-acpi-2.6Len Brown2005-09-081-31/+34
|\
| * [PATCH] Additions to .data.read_mostly sectionRavikiran G Thirumalai2005-09-081-5/+5
| | | | | | | | | | | | | | | | | | | | Mark variables which are usually accessed for reads with __readmostly. Signed-off-by: Alok N Kataria <alokk@calsoftinc.com> Signed-off-by: Shai Fultheim <shai@scalex86.org> Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
| * [PATCH] x86/x86_64: deferred handling of writes to /proc/irqxx/smp_affinityAshok Raj2005-09-081-26/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When handling writes to /proc/irq, current code is re-programming rte entries directly. This is not recommended and could potentially cause chipset's to lockup, or cause missing interrupts. CONFIG_IRQ_BALANCE does this correctly, where it re-programs only when the interrupt is pending. The same needs to be done for /proc/irq handling as well. Otherwise user space irq balancers are really not doing the right thing. - Changed pending_irq_balance_cpumask to pending_irq_migrate_cpumask for lack of a generic name. - added move_irq out of IRQ_BALANCE, and added this same to X86_64 - Added new proc handler for write, so we can do deferred write at irq handling time. - Display of /proc/irq/XX/smp_affinity used to display CPU_MASKALL, instead it now shows only active cpu masks, or exactly what was set. - Provided a common move_irq implementation, instead of duplicating when using generic irq framework. Tested on i386/x86_64 and ia64 with CONFIG_PCI_MSI turned on and off. Tested UP builds as well. MSI testing: tbd: I have cards, need to look for a x-over cable, although I did test an earlier version of this patch. Will test in a couple days. Signed-off-by: Ashok Raj <ashok.raj@intel.com> Acked-by: Zwane Mwaikambo <zwane@holomorphy.com> Grudgingly-acked-by: Andi Kleen <ak@muc.de> Signed-off-by: Coywolf Qi Hunt <coywolf@lovecn.org> Signed-off-by: Ashok Raj <ashok.raj@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | [ACPI] delete CONFIG_ACPI_BOOTLen Brown2005-08-241-2/+2
|/ | | | | | it has been a synonym for CONFIG_ACPI since 2.6.12 Signed-off-by: Len Brown <len.brown@intel.com>
* [PATCH] x86: i8253/i8259A lock cleanupIngo Molnar2005-06-301-1/+1
| | | | | | | | Introduce proper declarations for i8253_lock and i8259A_lock. Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Merge Christoph's freeze cleanup patchLinus Torvalds2005-06-261-1/+1
|\
| * [PATCH] Cleanup patch for process freezingChristoph Lameter2005-06-261-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1. Establish a simple API for process freezing defined in linux/include/sched.h: frozen(process) Check for frozen process freezing(process) Check if a process is being frozen freeze(process) Tell a process to freeze (go to refrigerator) thaw_process(process) Restart process frozen_process(process) Process is frozen now 2. Remove all references to PF_FREEZE and PF_FROZEN from all kernel sources except sched.h 3. Fix numerous locations where try_to_freeze is manually done by a driver 4. Remove the argument that is no longer necessary from two function calls. 5. Some whitespace cleanup 6. Clear potential race in refrigerator (provides an open window of PF_FREEZE cleared before setting PF_FROZEN, recalc_sigpending does not check PF_FROZEN). This patch does not address the problem of freeze_processes() violating the rule that a task may only modify its own flags by setting PF_FREEZE. This is not clean in an SMP environment. freeze(process) is therefore not SMP safe! Signed-off-by: Christoph Lameter <christoph@lameter.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
generated by cgit v1.2.3-55-g7522 (git 2.39.0) at 2024-07-16 18:43:11 +0200