summaryrefslogtreecommitdiffstats
path: root/arch/powerpc/boot
Commit message (Collapse)AuthorAgeFilesLines
* powerpc/40x: Add proper BOOTCFLAGS for cuboot-acadiaJosh Boyer2008-12-111-0/+1
| | | | | | | | The cuboot-acadia.c wrapper can cause assembler errors on some toolchains due to the lack of the proper BOOTCFLAGS. This adds the proper flags for the file. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* powerpc/83xx: Fix MCU support merge issue in mpc8349emitx.dtsAnton Vorontsov2008-12-031-8/+8
| | | | | | | | | | | | | Just found the merge issue in 442746989d92afc125040e0f29b33602ad94da99 ("powerpc/83xx: Add support for MCU microcontroller in .dts files"): the commit adds the MCU controller node into the DMA node, which is wrong because the MCU sits on the I2C bus. Fix this by moving the MCU node into the I2C controller node. The original patch[1] was OK though. ;-) Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/mpc832x_rdb: fix swapped ethernet idsMichael Barkowski2008-11-191-2/+2
| | | | | | | | | | | ethernet0 (called FSL UEC0 in U-Boot) should be enet1 (UCC3/eth1), and ethernet1 should be enet0 (UCC2/eth0), to be consistent with U-Boot so that the interfaces do not swap addresses when control passes from U-Boot to the kernel. Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com> Acked-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: L2 cache size wrong in 8572DS dtsTrent Piepho2008-11-191-1/+1
| | | | | | | | It's 1MB, not 512KB. Newer U-Boots will fix this entry, but that's no reason to have the wrong value in the dts. Signed-off-by: Trent Piepho <tpiepho@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/86xx: Correct SOC bus-frequency in GE Fanuc SBC610 DTSMartyn Welch2008-11-081-1/+1
| | | | | | | This patch corrects the bus-frequency value provided in the SBC610's dts. Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Revert "powerpc: Sync RPA note in zImage with kernel's RPA note"Paul Mackerras2008-10-312-137/+47Star
| | | | | | | | | | | | This reverts commit 91a00302959545a9ae423e99732b1e46eb19e877, plus commit 0dcd440120ef12879ff34fc78d7e4abf171c79e4 ("powerpc: Revert CHRP boot wrapper to real-base = 12MB on 32-bit") which depended on it. Commit 91a00302 was causing NVRAM corruption on some pSeries machines, for as-yet unknown reasons, so this reverts it until the cause is identified. Signed-off-by: Paul Mackerras <paulus@samba.org>
* Merge branch 'merge' of ↵Paul Mackerras2008-10-311-39/+0Star
|\ | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc into merge
| * powerpc: Remove duplicate DMA entry from mpc8313erdb device treeMike Dyer2008-10-311-39/+0Star
| | | | | | | | | | | | | | | | Commit 574366128db29e7da609ec1f9c01bf9d80adec87 added a duplicate DMA controller node. Signed-off-by: Mike Dyer <mike.dyer@provision-comm.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc: Fix format string warning in arch/powerpc/boot/main.cJon Smirl2008-10-311-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix format string warning in arch/powerpc/boot/main.c. Also correct a typo ("uncomressed") on the same line. BOOTCC arch/powerpc/boot/main.o arch/powerpc/boot/main.c: In function 'prep_kernel': arch/powerpc/boot/main.c:65: warning: format '%08x' expects type 'unsigned int', but argument 3 has type 'long unsigned int' Signed-off-by: Jon Smirl <jonsmirl@gmail.com> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* | powerpc: Fix bug in kernel copy of libfdt's fdt_subnode_offset_namelen()David Gibson2008-10-311-3/+6
|/ | | | | | | | | | | | | | | | | There's currently an off-by-one bug in fdt_subnode_offset_namelen() which causes it to keep searching after it's finished the subnodes of the given parent, and into the subnodes of siblings of the original node which come after it in the tree. This bug was introduced in commit ed95d7450dcbfeb45ffc9d39b1747aee82b49a51 ("powerpc: Update in-kernel dtc and libfdt to version 1.2.0"). A patch has already been submitted to dtc/libfdt mainline. We don't really want to pull in a new upstream version during the 2.6.28 cycle, but we should still fix this bug, hence this standalone version of the fix for the in-kernel libfdt. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* powerpc: Add del_node() for early boot code to prune inapplicable devices.Mike Ditto2008-10-222-0/+12
| | | | | | | | | Some platforms have variants that can share most of a flat device tree but need a few devices selectively pruned at boot time. This adds del_node() to ops.h to allow access to the existing fdt_del_node(). Signed-off-by: Mike Ditto <mditto@consentry.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* Merge commit 'kumar/kumar-for-2.6.28'Benjamin Herrenschmidt2008-10-2112-24/+79
|\
| * powerpc/83xx: Add DS1339 RTC support for MPC8349E-mITX boards .dtsAnton Vorontsov2008-10-212-0/+16
| | | | | | | | | | | | | | | | | | The RTC is sitting on the I2C2 bus at address 0x68. RTC interrupt signal is connected to the IPIC's EXT2 interrupt line, the line is shared with Vitesse 8201 Ethernet PHY. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/83xx: Add support for MCU microcontroller in .dts filesAnton Vorontsov2008-10-215-0/+40
| | | | | | | | | | | | | | | | | | | | | | MCU is an external Freescale MC9S08QG8 microcontroller, mainly used to provide soft power-off function, but also exports two GPIOs (wired to the LEDs and also available from the external headers). Added the MCU on mpc8349emitx, mpc837xrdb and mpc8315erdb boards. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Move mpc8572ds.dts to address-cells/size-cells = <2>Kumar Gala2008-10-211-14/+13Star
| | | | | | | | | | | | | | | | Change the top-level #address-cells and #size-cells to <2> so the mpc8572ds.dts is easier to deal with both a true 32-bit physical or 36-bit physical address space. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc: Remove device_type = "board_control" properties in .dts filesAnton Vorontsov2008-10-214-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | We don't want to encourage the bogus device_type usage. The device type isn't used in the code, so we can simply remove it from the documentation and dts files. Boards should specify proper compatible entries instead. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Fix mpc8536ds dma interrupt numbersEd Swarthout2008-10-211-4/+4
| | | | | | | | | | Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Enable enhanced functions for 8536 TSECJason Jin2008-10-211-2/+2
| | | | | | | | | | Signed-off-by: Jason Jin <Jason.jin@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc: Revert CHRP boot wrapper to real-base = 12MB on 32-bitPaul Mackerras2008-10-212-15/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 9b09c6d909dfd8de96b99b9b9c808b94b0a71614 ("powerpc: Change the default link address for pSeries zImage kernels") changed the real-base value in the CHRP note added by addnote to the zImage from 12MB to 32MB. It turns out that this causes unnecessary extra reboots on old 32-bit CHRP machines. This therefore adds a -r flag to addnote to allow us to specify what real-base value it should put in the CHRP note, and adjusts the wrapper script to pass -r c00000 to addnote when making a zImage for a CHRP machine. Also, CHRP machines ignore the RPA note, so we don't need to arrange for it to be the same as the kernel's. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* | powerpc: Add missing cuImage.initrd.% targetGrant Likely2008-10-211-0/+3
| | | | | | | | | | | | | | This target is needed to build cuImages with an embedded ramdisk image. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* | powerpc: Fix boot wrapper memcmp() called with zero length argumentMike Ditto2008-10-211-1/+3
| | | | | | | | | | | | | | | | | | I noticed, when trying to use, e.g., node = find_node_by_prop_value(prev, "booleanprop", "", 0)) to search for all nodes with a certain boolean property, that memcmp() returns garbage when comparing zero bytes. It should return zero. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* | powerpc/boot: Compare _start against ei.loadsize instead ei.memsizeSebastian Siewior2008-10-212-10/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the vmlinux binary in memory is larger than 4 MiB than it collides with the initial boot code which is linked at 4 MiB in case of cuBoot. If the the uncompressed image size (on disk size) is less than 4 MiB then it would fit. The difference between those two sizes is the bss section. In cuBoot we have the dtb embedded right after the data section so it is very likely that the reset of the bss section (in kernel's start up code) will overwrite the dtb blob. Therefore we reallocate the dtb. Something similar is allready done to the initrd. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* | Merge commit 'gcl/gcl-next'Benjamin Herrenschmidt2008-10-211-0/+4
|\ \
| * | powerpc/52xx: Make cuImage more robust in locating immr node.Grant Likely2008-10-151-0/+4
| |/ | | | | | | | | | | | | | | Current device trees do not have the device_type = soc property set anymore. Fix up the cuImage bootwrapper fragment to still find the IMMR nodes. Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* | powerpc/40x: Add support for Netstal HCU4 boardNiklaus Giger2008-10-171-0/+168
| | | | | | | | | | | | | | Adds support for a HCU4 PPC405GPr based board from Netstal Maschinen AG. Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* | powerpc/40x: Add cuboot wrapper for Acadia boardJosh Boyer2008-10-172-1/+177
| | | | | | | | | | | | | | This adds a cuboot wrapper for the AMCC PowerPC 405EZ Acadia board. The clocking code is derived from U-Boot, originally written by Stefan Roese. Signed-off-by: Josh Boyer <jwboyer@linux.ibm.com>
* | powerpc/40x: AMCC PowerPC 405EZ Acadia DTSJosh Boyer2008-10-171-0/+224
|/ | | | | | | | | | | | | | | | Add the base DTS for the AMCC PowerPC 405EZ Acadia evalution board. In addition to some of the normal PPC 40x peripherals, the Acadia board has: - 64 MiB PSRAM - NOR and NAND flash - Two USB 1.1 host ports - Two CAN 2.0 ports - ADC and DAC connectors - LCD display This adds the basic platform support to build from. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* Merge commit 'origin'Benjamin Herrenschmidt2008-10-153-58/+58
|\ | | | | | | | | | | Manual fixup of conflicts on: arch/powerpc/include/asm/dcr-regs.h drivers/net/ibm_newemac/core.h
| * powerpc: Fix PCI in Holly device treeDavid Gibson2008-09-301-53/+53
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The PCI bridge on the Holly board is incorrectly represented in the device tree. The current device tree node for the PCI bridge sits under the tsi-bridge node. That's not obviously wrong, but the PCI bridge translates some PCI spaces into CPU address ranges which were not translated by the "ranges" property in tsi-bridge node. We used to get away with this problem because the PCI bridge discovery code was also buggy, assuming incorrectly that PCI host bridge nodes were always directly under the root bus and treating the translated addresses as raw CPU addresses, rather than parent bus addresses. This has since been fixed, thus breaking Holly. This could be fixed by adding extra translations to the tsi-bridge node, but this patch instead moves the Holly PCI bridge out of the tsi-bridge node to the root bus. This makes the tsi-bridge node represent only the built-in IO devices in the bridge, with a more-or-less contiguous address range. This is the same convention used on Freescale SoC chips, where the "soc" node represents only the IMMR region, and the PCI and other bus bridges are separate nodes under the root bus. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
| * powerpc: Holly board needs dtbImage targetJosh Boyer2008-09-171-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | One of the changes in the bootwrapper makefile introduced the dtbImage targets for boards that need a simple zImage with a DTB embedded in them (595be948cce574ff2d5dde5d0426a636a4363c70, "[POWERPC] bootwrapper: Build multiple cuImages"). When this was done, it broke booting on the Holly board as the zImage.holly wrapper did not get the DTB embedded properly. This changes the target for the Holly board to a dtbImage so that the wrapper includes the vmlinux, wrapper bits, and DTB. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * powerpc: Fix interrupt values for DMA2 in MPC8610 HPCD device treeTimur Tabi2008-09-161-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For Freescale 8xxx devices that use an MPIC, the interrupt numbers in the device tree must be 16 greater than the values documented in the reference manual. In these chips, the MPIC is wired to use the first 16 numbers for external interrupts, but the documentation numbers internal interrupts from 0. In the MPC8610 HPCD device tree, the interrupt properties for the DMA channels for DMA2 were not the adjusted values. This fixes that. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
* | powerpc/83xx: add NAND support for the MPC8360E-RDK boardsAnton Vorontsov2008-10-131-0/+12
| | | | | | | | | | | | | | | | | | | | | | The StMicro NAND chip (512Mbit, 64MB) is connected to the local bus, the first local bus' user-programmable machine is configured by the firmware to work with NAND chips. QE GPIO pin is used to poll the NAND's Ready-Not-Busy signal. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc: FPGA support for GE Fanuc SBC610Martyn Welch2008-10-131-0/+4
| | | | | | | | | | | | | | | | | | | | | | Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D). This patch adds support for the registers held in the devices main FPGA, exposing extra information about the revision of the board through cpuinfo. Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc: reserve two DMA channels for audio in MPC8610 HPCD device treeTimur Tabi2008-10-131-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | The Freescale Elo DMA driver binds to all DMA channels in the device tree that are compatible with "fsl,eloplus-dma-channel". This conflicts with the sound drivers for the MPC8610 HPCD. On this board, the SSI uses two DMA channels and therefore those channels are not available for general purpose use. We change the compatible properties for these channels "fsl,ssi-dma-channel". This works because the sound drivers don't actually check the compatible property when it grabs channels. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/83xx: add DS1374 RTC support for the MPC837xE-MDS boardsAnton Vorontsov2008-10-133-0/+21
| | | | | | | | | | | | | | | | The RTC is sitting on the I2C1 bus at address 0x68. RTC interrupt signal is connected to the IPIC's EXT3 interrupt line. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/5121: Add PCI support.John Rigby2008-10-131-1/+2
| | | | | | | | | | | | | | | | | | | | | | Uses mpc83xx_add_bridge in fsl_pci.c Adds second register tuple to pci node register property as done for 83xx device trees in a previous patch. Signed-off-by: John Rigby <jrigby@freescale.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc: 83xx: pci: Remove need for get_immrbase from mpc83xx_add_bridge.John Rigby2008-10-1316-18/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Modify mpc83xx_add_bridge to get config space register base address from the device tree instead of immr + hardcoded offset. 83xx pci nodes have this change: register properties now contain two address length tuples: First is the pci bridge register base, this has always been there. Second is the config base, this is new. This is documented in dts-bindings/fsl/83xx-512x-pci.txt The changes accomplish these things: mpc83xx_add_bridge no longer needs to call get_immrbase it uses hard coded addresses if the second register value is missing Signed-off-by: John Rigby <jrigby@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc: GE Fanuc's FPGA based PIC controller on the SBC610Martyn Welch2008-10-131-4/+33
| | | | | | | | | | | | | | | | | | | | | | | | Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D). A number of MPC8641D based route interrupts for on-board interrupts through a FPGA based interrupt controller, which is chained with the MPC8641D's mpic. This patch provides a basic driver to allow basic routing of interrupts to the mpic. Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/85xx: Wire up RTC interrupt on MPC8536DSKumar Gala2008-10-131-0/+2
| | | | | | | | | | | | Add interrupt info to the MPC8536DS .dts for the RTC Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc: Sync RPA note in zImage with kernel's RPA notePaul Mackerras2008-10-102-37/+111
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 9b09c6d909dfd8de96b99b9b9c808b94b0a71614 ("powerpc: Change the default link address for pSeries zImage kernels") changed the real-base value in the CHRP note added by the addnote program from 12MB to 32MB to give more space for Open Firmware to load the zImage. (The real-base value says where we want OF to position itself in memory.) However, this change was ineffective on most pSeries machines, because the RPA note added by addnote has the "ignore me" flag set to 1. This was intended to tell OF to ignore just the RPA note, but has the side effect of also making OF ignore the CHRP note (at least on most pSeries machines). To solve this we have to set the "ignore me" flag to 0 in the RPA note. (We can't just omit the RPA note because that is equivalent to having an RPA note with default values, and the default values are not what we want.) However, then we have to make sure the values in the zImage's RPA note match up with the values that the kernel supplies later in prom_init.c with either the ibm,client-architecture-support call or the process-elf-header call in prom_send_capabilities(). So this sets the "ignore me" flag in the RPA note in addnote to 0, and adjusts the RPA note values in addnote.c and in prom_init.c to be consistent with each other and with the values in ibm_architecture_vec. However, since the wrapper is independent of the kernel, this doesn't ensure that the notes will stay consistent. To ensure that, this adds code to addnote.c so that it can extract the kernel's RPA note from the kernel binary and put that in the zImage. To that end, we put the kernel's fake ELF header (which contains the kernel's RPA note) into its own section, and arrange for wrapper to pull out that section with objcopy and pass it to addnote, which then extracts the RPA note from it and transfers it to the zImage. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* | Merge commit 'jwb/jwb-next'Benjamin Herrenschmidt2008-10-071-0/+293
|\ \
| * | powerpc/44x: Add AMCC Arches DTSVictor Gallardo2008-10-021-0/+293
| | | | | | | | | | | | | | | | | | | | | Basic functionality for the AMCC Arches eval Board. Signed-off-by: Victor Gallardo <vgallardo@amcc.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* | | powerpc/83xx: Add missing cell-index to dma-channel device nodesKumar Gala2008-09-2417-0/+68
|/ / | | | | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | Merge branch 'powerpc-next' of ↵Paul Mackerras2008-09-225-6/+622
|\ \ | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc
| * | powerpc: add SSI-to-DMA properties to Freescale MPC8610 HPCD device treeTimur Tabi2008-09-171-3/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add the fsl,playback-dma and fsl,capture-dma properties to the Freescale MPC8610 HPCD device tree. These properties connect the SSI nodes to the DMA nodes for the DMA channels that the SSI should use. Also update the ssi.txt documentation. These properties will be needed when the ASoC V2 version of the Freescale MPC8610 device drivers are merged into the mainline. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | powerpc: Board support for GE Fanuc SBC610Martyn Welch2008-09-161-0/+260
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D). This is the basic board support for GE Fanuc's SBC610, a 6U single board computer, based on Freescale's MPC8641D. Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | powerpc/83xx: mpc836x_mds: add support for the nor flashAnton Vorontsov2008-09-161-3/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the localbus node, moves the bcsr node into the localbus node, and adds the flash node. Also enable MTD support in the defconfig. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | powerpc: Add support for mpc8247 based board MGCOGE from keymile.Heiko Schocher2008-09-161-0/+174
| | | | | | | | | | | | | | | Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | powerpc: Add support for the MPC852 based mgsuvd board from keymile.Heiko Schocher2008-09-161-0/+163
| | | | | | | | | | | | | | | | | | | | | Supported SMC1 (serial console), SCC3 Ethernet (10Mbps hdx). Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | | Merge branch 'next' of ↵Paul Mackerras2008-09-223-2/+11
|\ \ \ | |/ / |/| | | | | ssh://master.kernel.org/pub/scm/linux/kernel/git/jwboyer/powerpc-4xx
generated by cgit v1.2.3-55-g7522 (git 2.39.0) at 2024-07-10 16:31:15 +0200