| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
| |
We shouldn't directly access sysdata to get the pci_controller. Instead
use pci_bus_to_host() for this purpose. In the future we might have
sysdata be a device_node to match ppc64 and unify the code between ppc32
& ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The 440EPx/GRx chips don't support PCI MRM commands. Drivers determine this
by looking for a zero value in the PCI cache line size register. However,
some drivers write to this register upon initialization. This can cause
MRMs to be used on these chips, which may cause deadlocks on PLB4.
The workaround implemented here introduces a new indirect_type flag, called
PPC_INDIRECT_TYPE_BROKEN_MRM. This is set in the pci_controller structure in
the pci fixup function for 4xx PCI bridges by determining if the bridge is
compatible with 440EPx/GRx. The flag is checked in the indirect_write_config
function, and forces any writes to the PCI_CACHE_LINE_SIZE register to be
zero, which will disable MRMs for these chips.
A similar workaround has been tested by AMCC on various PCI cards, such as
the Silicon Image ATA card and Intel E1000 GIGE card. Hangs were seen with
the Silicon Image card, and MRMs were seen on the bus with a PCI analyzer.
With the workaround in place, the card functioned properly and only Memory
Reads were seen on the bus with the analyzer.
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
| |
|
|
|
|
|
|
| |
Add 64-bit physical address support to setup_indirect_pci().
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| |
|
|
|
| |
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
We didn't actually propogate the flag we pass into setup_indirect_pci()
to set indirect_type and thus were getting the wrong endianness if
PPC_INDIRECT_TYPE_BIG_ENDIAN was set.
Also, we need to or in additional flags rather than just doing a
direct assignment.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| |
|
|
|
|
|
|
| |
Make it so we do a runtime check to know if we need to write cfg_addr
as big or little endian. This is needed if we want to allow 86xx support
to co-exist in the same kernel as other 6xx PPCs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| |
|
|
|
|
|
| |
We don't use setup_indirect_pci_nomap in arch/powerpc and it appears
the users that needed it from arch/ppc are now using setup_indirect_pci.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| |
|
|
|
|
|
|
|
| |
Added PPC_INDIRECT_TYPE_NO_PCIE_LINK flag to the indirect pci handling
code to ensure that we don't talk to any device other than the PHB
if we don't have PCIe link. Some controllers will lockup if they try
to do a config cycle to any device on the bus except the PHB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Freescale PCI-e controllers have an issue in that they use the
PCI_PRIMARY_BUS register in the virtual P2P bridge to determine which
bus number to match on when generating a type 0 config cycle. The
issue is if we are renumbering bus numbers to match Linux we will try
setting the PCI_PRIMARY_BUS and will not know which bus number to use
for generating type 0 config cycles. We surpress writing the register
in the P2P bridge and always keep it at zero.
In the future when proper PCI domain support is working we should be
able to remove this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
The generic PCI config ops indirect support for ppc32 covers only two
cases (implicit vs explicit) type 0/1 config cycles via set_cfg_type.
Added a indirect_type bit mask to handle other variants.
Added support for PCI-e extended registers and moved the cfg_type
handling into the bit mask for ARCH=powerpc. We can also use this to
handle indirect quirks.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
Removed the remants of bus_offset and use self_busno in the mv64x60 case
and use pci_assign_all_buses on 83xx/85xx.
83xx/85xx have multiple PHBs and the firmwares on these devices tend not
to handle topologies with P2P bridges well so we let Linux just reassign
the bus numbers to match.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| |
|
|
|
|
|
|
|
| |
Added self_busno to pci_controller and indirect PCI ops to be set by
board code to indicate which bus number to use when talking to the PHB.
By default we use zero since the majority of controllers that have
implicit mechanisms to talk to the PHBs use a bus number of zero.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| |
|
|
|
|
|
|
|
|
| |
There are times that we need to know which controller we are on to decide
how to exclude devices properly. We now pass the pci_controller that we
are going to use down to the pci_exclude_device function. This will
greatly simplify being able to exclude the PHBs in multiple controller
setups.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
|
This also puts a copy of indirect_pci.c in arch/powerpc/sysdev
so that we don't need to build in arch/ppc/syslib.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
