summaryrefslogtreecommitdiffstats
path: root/drivers/hwmon
Commit message (Collapse)AuthorAgeFilesLines
* hwmon: lis3: Release resources in case of failureSamu Onkalo2010-10-251-0/+5
| | | | | | | | | If lis3lv02d_init_device fails, HW resources were not released properly. In case of failure call release_resources if available. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: lis3: Enhance lis3 selftest with IRQ line testSamu Onkalo2010-10-252-9/+82
| | | | | | | | | Configure chip to data ready mode in selftest and count received interrupts to see that interrupt line(s) are working. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: lis3: use block read to access data registersSamu Onkalo2010-10-253-3/+32
| | | | | | | | | | | | | | Add optional blockread function to interface driver. If available the chip driver uses it for data register access. For 12 bit device it reads 6 bytes to get 3*16bit data. For 8 bit device it reads out 5 bytes since every second byte is dummy. This optimizes bus usage and reduces number of operations and interrupts needed for one data update. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: lis3: Adjust fuzziness for 8 bit deviceSamu Onkalo2010-10-251-4/+14
| | | | | | | | | | | | Default fuziness is set smaller for 8 device. In 12 bit device LSB is quite close to 1 mg (mg = 1 / 1000 of earth gravity). In 8bit device LSB is about 18 mg. Set fuziness to 1 for 8 bit device. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: lis3: New parameters to platform dataSamu Onkalo2010-10-251-7/+14
| | | | | | | | | | | | | | | | Added default output data rate setting to platform data. If default rate is 0, reset default value is used. Added control for duration via platform data. Added possibility to configure interrupts to trig on both rising and falling edge. The lis3 WU unit can be configured quite many ways and with some configurations it is quite handy to get coordinate refresh when some event trigs and when it reason goes away. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: lis3: restore axis enabled bitsSamu Onkalo2010-10-252-2/+2
| | | | | | | | | All axis enable bits are set to 0 at module remove. Restore reset default value at init. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: lis3: Power on correctionsSamu Onkalo2010-10-252-8/+12
| | | | | | | | | | | | Sometimes lis3 chip seems to fail to setup factory tuning at boot up. This probably happens if there is some odd power ramp down ramp up sequence for example in device restart. Set boot bit in control2 register to trig boot sequence manually and wait until it is finished. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: lis3: Update coordinates at polled device openSamu Onkalo2010-10-251-0/+5
| | | | | | | | | | Call input device poll function at device open to refresh coordinates immediately. This is needed for the case where poll interval is set to zero and coordinate updates happens purely under interrupt control. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: lis3: Cleanup interrupt handlingSamu Onkalo2010-10-252-22/+13Star
| | | | | | | | | | | | | | | | Irqcfg moved to chip data instead of platform data. This simplifies access in interrupt handler little bit. Input device open and close functions set status for interrupt threaded handler once. Unnecessary check for interrupt source removed since it is enough that active interrupt line indicates that there was an interrupt. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: lis3: regulator controlSamu Onkalo2010-10-253-1/+119
| | | | | | | | | | | | Based on pm_runtime control, turn lis3 regulators on and off. Perform context save and restore on transitions. Feature is optional and must be enabled in platform data. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: lis3: pm_runtime supportSamu Onkalo2010-10-253-13/+102
| | | | | | | | | | | | | | | | Add pm_runtime support to lis3 core driver. Add pm_runtime support to lis3 i2c driver. spi and hp_accel drivers are not yet supported. Old always on functionality remains for those. For sysfs there is 5 second delay before turning off the chip to avoid long ramp up delay. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: add generic GPIO fan driverSimon Guinot2010-10-253-0/+568
| | | | | | | | | | This patch adds hwmon support for fans connected to GPIO lines. Platform specific information such as GPIO pinout and speed conversion array (rpm from/to GPIO value) are passed to the driver via platform_data. Signed-off-by: Simon Guinot <sguinot@lacie.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: (coretemp) fix reading of microcode revision (v2)Jan Beulich2010-10-251-2/+18
| | | | | | | | | | | | | | | | | According to the documentation, simply reading the respective MSR isn't sufficient: It should be written with zeros, cpuid(1) be executed, and then read (see arch/x86/kernel/cpu/intel.c for an example). v2: Fail probe when microcode revision cannot be determined, but is needed to check for proper operation. Signed-off-by: Jan Beulich <jbeulich@novell.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Chen Gong <gong.chen@linux.intel.com> Cc: Jean Delvare <khali@linux-fr.org> Acked-by: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: ({core, pkg, via-cpu}temp) remove unnecessary CONFIG_HOTPLUG_CPU ifdefsChen Gong2010-10-253-14/+3Star
| | | | | | | | CONFIG_HOTPLUG_CPU is used too much in some drivers. This patch clean them up. Signed-off-by: Chen Gong <gong.chen@linux.intel.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: (pkgtemp) align driver initialization style with coretempChen Gong2010-10-251-14/+8Star
| | | | | | | | | pkgtemp is derived from coretemp, so some reasonable logics should be applied onto pkgtemp, too. Such as the init logic here. Signed-off-by: Chen Gong <gong.chen@linux.intel.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: LTC4261 Hardware monitoring driverGuenter Roeck2010-10-253-0/+327
| | | | | | | | | This driver adds support for Linear Technology LTC4261 I2C Negative Voltage Hot Swap Controller. Reviewed-by: Ira W. Snyder <iws@ovro.caltech.edu> Reviewed-by: Tom Grennan <tom.grennan@ericsson.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: (lis3) add axes module parameter for custom axis-mappingTakashi Iwai2010-10-255-21/+52
| | | | | | | | | | | | | | | | | | The axis-mapping of lis3dev device on many (rather most) HP machines doesn't follow the standard. When each new model appears, users need to adjust again. Testing this requires the rebuild of kernel, thus it's not trivial for end-users. This patch adds a module parameter "axes" to allow a custom axis-mapping without patching and recompiling the kernel driver. User can pass the parameter such as axes=3,2,1. Also it can be changed via sysfs. Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Cc: Jean Delvare <khali@linux-fr.org> Cc: Guenter Roeck <guenter.roeck@ericsson.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: (hp_accel) Add HP Mini 510x family supportMasanari Iida2010-10-251-1/+1
| | | | | | | | | | | | | This patch is an enhanced version of Takashi Iwai's [PATCH] hp_accel: Add quirks for HP ProBook 532x and HP Mini 5102 My HP Mini 5101 works fine with this patch. Confirmed with Tux Racer. Signed-off by: Masanari Iida <standby24x7@gmail.com> Acked-by: Takashi Iwai <tiwai@suse.de> Cc: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: (lis3) Add support for new LIS3DC / HP3DC chipTakashi Iwai2010-10-252-8/+44
| | | | | | | | A new version of LIS3 chip has slight incompatibilities from former versions. This patch adds the minimal support for it. Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* x86/hwmon: remove inclusion of unnecessary headers from {core, pkg, ↵Jan Beulich2010-10-253-4/+0Star
| | | | | | | | | | via-cpu}temp.c These likely originate from these drivers being clones of one another and/or other drivers which actually needed these includes. Signed-off-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* x86/hwmon: (coretemp) cosmetic cleanupJan Beulich2010-10-251-2/+0Star
| | | | | | | | | "break" after "return" is at best bogus (good compilers even warn about the "break" being unreachable). Signed-off-by: Jan Beulich <jbeulich@novell.com> Cc: Rudolf Marek <r.marek@assembler.cz> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* x86/hwmon: {core, pkg, via}cpu_temp_device_remove() can all be __cpuinitJan Beulich2010-10-253-3/+3
| | | | | | | ... as they're being called only from a __cpuinit function. Signed-off-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* Merge branch 'for_linus' of ↵Linus Torvalds2010-10-253-658/+0Star
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86 * 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (44 commits) eeepc-wmi: Add cpufv sysfs interface eeepc-wmi: add additional hotkeys panasonic-laptop: Simplify calls to acpi_pcc_retrieve_biosdata panasonic-laptop: Handle errors properly if they happen intel_pmic_gpio: fix off-by-one value range checking IBM Real-Time "SMI Free" mode driver -v7 Add OLPC XO-1 rfkill driver Move hdaps driver to platform/x86 ideapad-laptop: Fix Makefile intel_pmic_gpio: swap the bits and mask args for intel_scu_ipc_update_register ideapad: Add param: no_bt_rfkill ideapad: Change the driver name to ideapad-laptop ideapad: rewrite the sw rfkill set ideapad: rewrite the hw rfkill notify ideapad: use EC command to control camera ideapad: use return value of _CFG to tell if device exist or not ideapad: make sure we bind on the correct device ideapad: check VPC bit before sync rfkill hw status ideapad: add ACPI helpers dell-laptop: Add debugfs support ...
| * Move hdaps driver to platform/x86Jean Delvare2010-10-213-658/+0Star
| | | | | | | | | | | | | | | | | | | | | | | | The hdaps driver isn't a hardware monitoring driver, so it shouldn't live under driver/hwmon. drivers/platform/x86 seems much more appropriate, as the driver is only useful on x86 laptops. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Guenter Roeck <guenter.roeck@ericsson.com> Cc: Matthew Garrett <mjg@redhat.com> Cc: Frank Seidel <frank@f-seidel.de> Signed-off-by: Matthew Garrett <mjg@redhat.com>
* | Merge branch 'for-next' of ↵Linus Torvalds2010-10-245-6/+6
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits) Update broken web addresses in arch directory. Update broken web addresses in the kernel. Revert "drivers/usb: Remove unnecessary return's from void functions" for musb gadget Revert "Fix typo: configuation => configuration" partially ida: document IDA_BITMAP_LONGS calculation ext2: fix a typo on comment in ext2/inode.c drivers/scsi: Remove unnecessary casts of private_data drivers/s390: Remove unnecessary casts of private_data net/sunrpc/rpc_pipe.c: Remove unnecessary casts of private_data drivers/infiniband: Remove unnecessary casts of private_data drivers/gpu/drm: Remove unnecessary casts of private_data kernel/pm_qos_params.c: Remove unnecessary casts of private_data fs/ecryptfs: Remove unnecessary casts of private_data fs/seq_file.c: Remove unnecessary casts of private_data arm: uengine.c: remove C99 comments arm: scoop.c: remove C99 comments Fix typo configue => configure in comments Fix typo: configuation => configuration Fix typo interrest[ing|ed] => interest[ing|ed] Fix various typos of valid in comments ... Fix up trivial conflicts in: drivers/char/ipmi/ipmi_si_intf.c drivers/usb/gadget/rndis.c net/irda/irnet/irnet_ppp.c
| * | Update broken web addresses in the kernel.Justin P. Mattock2010-10-185-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch below updates broken web addresses in the kernel Signed-off-by: Justin P. Mattock <justinmattock@gmail.com> Cc: Maciej W. Rozycki <macro@linux-mips.org> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Finn Thain <fthain@telegraphics.com.au> Cc: Randy Dunlap <rdunlap@xenotime.net> Cc: Matt Turner <mattst88@gmail.com> Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com> Cc: Mike Frysinger <vapier.adi@gmail.com> Acked-by: Ben Pfaff <blp@cs.stanford.edu> Acked-by: Hans J. Koch <hjk@linutronix.de> Reviewed-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* | | Merge branch 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bklLinus Torvalds2010-10-221-0/+1
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl: vfs: make no_llseek the default vfs: don't use BKL in default_llseek llseek: automatically add .llseek fop libfs: use generic_file_llseek for simple_attr mac80211: disallow seeks in minstrel debug code lirc: make chardev nonseekable viotape: use noop_llseek raw: use explicit llseek file operations ibmasmfs: use generic_file_llseek spufs: use llseek in all file operations arm/omap: use generic_file_llseek in iommu_debug lkdtm: use generic_file_llseek in debugfs net/wireless: use generic_file_llseek in debugfs drm: use noop_llseek
| * | | llseek: automatically add .llseek fopArnd Bergmann2010-10-151-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All file_operations should get a .llseek operation so we can make nonseekable_open the default for future file operations without a .llseek pointer. The three cases that we can automatically detect are no_llseek, seq_lseek and default_llseek. For cases where we can we can automatically prove that the file offset is always ignored, we use noop_llseek, which maintains the current behavior of not returning an error from a seek. New drivers should normally not use noop_llseek but instead use no_llseek and call nonseekable_open at open time. Existing drivers can be converted to do the same when the maintainer knows for certain that no user code relies on calling seek on the device file. The generated code is often incorrectly indented and right now contains comments that clarify for each added line why a specific variant was chosen. In the version that gets submitted upstream, the comments will be gone and I will manually fix the indentation, because there does not seem to be a way to do that using coccinelle. Some amount of new code is currently sitting in linux-next that should get the same modifications, which I will do at the end of the merge window. Many thanks to Julia Lawall for helping me learn to write a semantic patch that does all this. ===== begin semantic patch ===== // This adds an llseek= method to all file operations, // as a preparation for making no_llseek the default. // // The rules are // - use no_llseek explicitly if we do nonseekable_open // - use seq_lseek for sequential files // - use default_llseek if we know we access f_pos // - use noop_llseek if we know we don't access f_pos, // but we still want to allow users to call lseek // @ open1 exists @ identifier nested_open; @@ nested_open(...) { <+... nonseekable_open(...) ...+> } @ open exists@ identifier open_f; identifier i, f; identifier open1.nested_open; @@ int open_f(struct inode *i, struct file *f) { <+... ( nonseekable_open(...) | nested_open(...) ) ...+> } @ read disable optional_qualifier exists @ identifier read_f; identifier f, p, s, off; type ssize_t, size_t, loff_t; expression E; identifier func; @@ ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off) { <+... ( *off = E | *off += E | func(..., off, ...) | E = *off ) ...+> } @ read_no_fpos disable optional_qualifier exists @ identifier read_f; identifier f, p, s, off; type ssize_t, size_t, loff_t; @@ ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off) { ... when != off } @ write @ identifier write_f; identifier f, p, s, off; type ssize_t, size_t, loff_t; expression E; identifier func; @@ ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off) { <+... ( *off = E | *off += E | func(..., off, ...) | E = *off ) ...+> } @ write_no_fpos @ identifier write_f; identifier f, p, s, off; type ssize_t, size_t, loff_t; @@ ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off) { ... when != off } @ fops0 @ identifier fops; @@ struct file_operations fops = { ... }; @ has_llseek depends on fops0 @ identifier fops0.fops; identifier llseek_f; @@ struct file_operations fops = { ... .llseek = llseek_f, ... }; @ has_read depends on fops0 @ identifier fops0.fops; identifier read_f; @@ struct file_operations fops = { ... .read = read_f, ... }; @ has_write depends on fops0 @ identifier fops0.fops; identifier write_f; @@ struct file_operations fops = { ... .write = write_f, ... }; @ has_open depends on fops0 @ identifier fops0.fops; identifier open_f; @@ struct file_operations fops = { ... .open = open_f, ... }; // use no_llseek if we call nonseekable_open //////////////////////////////////////////// @ nonseekable1 depends on !has_llseek && has_open @ identifier fops0.fops; identifier nso ~= "nonseekable_open"; @@ struct file_operations fops = { ... .open = nso, ... +.llseek = no_llseek, /* nonseekable */ }; @ nonseekable2 depends on !has_llseek @ identifier fops0.fops; identifier open.open_f; @@ struct file_operations fops = { ... .open = open_f, ... +.llseek = no_llseek, /* open uses nonseekable */ }; // use seq_lseek for sequential files ///////////////////////////////////// @ seq depends on !has_llseek @ identifier fops0.fops; identifier sr ~= "seq_read"; @@ struct file_operations fops = { ... .read = sr, ... +.llseek = seq_lseek, /* we have seq_read */ }; // use default_llseek if there is a readdir /////////////////////////////////////////// @ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @ identifier fops0.fops; identifier readdir_e; @@ // any other fop is used that changes pos struct file_operations fops = { ... .readdir = readdir_e, ... +.llseek = default_llseek, /* readdir is present */ }; // use default_llseek if at least one of read/write touches f_pos ///////////////////////////////////////////////////////////////// @ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @ identifier fops0.fops; identifier read.read_f; @@ // read fops use offset struct file_operations fops = { ... .read = read_f, ... +.llseek = default_llseek, /* read accesses f_pos */ }; @ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @ identifier fops0.fops; identifier write.write_f; @@ // write fops use offset struct file_operations fops = { ... .write = write_f, ... + .llseek = default_llseek, /* write accesses f_pos */ }; // Use noop_llseek if neither read nor write accesses f_pos /////////////////////////////////////////////////////////// @ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @ identifier fops0.fops; identifier read_no_fpos.read_f; identifier write_no_fpos.write_f; @@ // write fops use offset struct file_operations fops = { ... .write = write_f, .read = read_f, ... +.llseek = noop_llseek, /* read and write both use no f_pos */ }; @ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @ identifier fops0.fops; identifier write_no_fpos.write_f; @@ struct file_operations fops = { ... .write = write_f, ... +.llseek = noop_llseek, /* write uses no f_pos */ }; @ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @ identifier fops0.fops; identifier read_no_fpos.read_f; @@ struct file_operations fops = { ... .read = read_f, ... +.llseek = noop_llseek, /* read uses no f_pos */ }; @ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @ identifier fops0.fops; @@ struct file_operations fops = { ... +.llseek = noop_llseek, /* no read or write fn */ }; ===== End semantic patch ===== Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Julia Lawall <julia@diku.dk> Cc: Christoph Hellwig <hch@infradead.org>
* | | | Merge branch 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bklLinus Torvalds2010-10-222-6/+6
|\ \ \ \ | |_|_|/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl: block: autoconvert trivial BKL users to private mutex drivers: autoconvert trivial BKL users to private mutex ipmi: autoconvert trivial BKL users to private mutex mac: autoconvert trivial BKL users to private mutex mtd: autoconvert trivial BKL users to private mutex scsi: autoconvert trivial BKL users to private mutex Fix up trivial conflicts (due to addition of private mutex right next to deletion of a version string) in drivers/char/pcmcia/cm40[04]0_cs.c
| * | | drivers: autoconvert trivial BKL users to private mutexArnd Bergmann2010-10-052-6/+6
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All these files use the big kernel lock in a trivial way to serialize their private file operations, typically resulting from an earlier semi-automatic pushdown from VFS. None of these drivers appears to want to lock against other code, and they all use the BKL as the top-level lock in their file operations, meaning that there is no lock-order inversion problem. Consequently, we can remove the BKL completely, replacing it with a per-file mutex in every case. Using a scripted approach means we can avoid typos. These drivers do not seem to be under active maintainance from my brief investigation. Apologies to those maintainers that I have missed. file=$1 name=$2 if grep -q lock_kernel ${file} ; then if grep -q 'include.*linux.mutex.h' ${file} ; then sed -i '/include.*<linux\/smp_lock.h>/d' ${file} else sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file} fi sed -i ${file} \ -e "/^#include.*linux.mutex.h/,$ { 1,/^\(static\|int\|long\)/ { /^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex); } }" \ -e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \ -e '/[ ]*cycle_kernel_lock();/d' else sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \ -e '/cycle_kernel_lock()/d' fi Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* | | hwmon: f71882fg: use a muxed resource lock for the Super I/O portGiel van Schijndel2010-10-031-13/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | Sleep while acquiring a resource lock on the Super I/O port. This should prevent collisions from causing the hardware probe to fail with -EBUSY. Signed-off-by: Giel van Schijndel <me@mortis.eu> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* | | hwmon (coretemp): Fix build breakage if SMP is undefinedGuenter Roeck2010-09-281-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit e40cc4bdfd4b89813f072f72bd9c7055814d3f0f introduced a build breakage if CONFIG_SMP is undefined. This commit fixes the problem. This fix is only a workaround. For a real fix, cpu_sibling_mask() should be defined in UP include code, eg in linux/smp.h, and asm/smp.h should not be included directly. This fix is currently not possible because asm/smp.h defines cpu_sibling_mask() unconditionally and is included directly from many source files. Reported-by: Ingo Molnar <mingo@elte.hu> Tested-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Cc: Fenghua Yu <fenghua.yu@intel.com>
* | | x86/hwmon: pkgtemp has no dependency on PCIJan Beulich2010-09-242-2/+1Star
| | | | | | | | | | | | | | | | | | | | | | | | | | | Other than coretemp, from which this code was apparently derived, there is no PCI specific code in this driver. Signed-off-by: Jan Beulich <jbeulich@novell.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* | | x86/hwmon: register alternate sibling upon CPU removalJan Beulich2010-09-241-7/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Just like pkgtemp registers another core of the same package when one gets removed, coretemp should register another hyperthread (if available) in that situation. As pointed out in the patch fixing the respective code in pkgtemp, the list protectng mutex must be dropped before calling coretemp_device_add(), and due to the restructured loop (including an explicit return) the "safe" variant of the list iterator isn't needed anymore. Signed-off-by: Jan Beulich <jbeulich@novell.com> Cc: Rudolf Marek <r.marek@assembler.cz> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* | | x86/hwmon: fix initialization of pkgtempJan Beulich2010-09-241-7/+3Star
| | | | | | | | | | | | | | | | | | | | | | | | Feature availability should also be checked in the hotplug code path. Signed-off-by: Jan Beulich <jbeulich@novell.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* | | x86/hwmon: fix initialization of coretempJan Beulich2010-09-241-16/+13Star
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Using cpuid_eax() to determine feature availability on other than the current CPU is invalid. And feature availability should also be checked in the hotplug code path. Signed-off-by: Jan Beulich <jbeulich@novell.com> Cc: Rudolf Marek <r.marek@assembler.cz> Cc: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* | | x86/hwmon: don't leak device attribute file from pkgtemp_probe() and ↵Jan Beulich2010-09-241-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | pkgtemp_remove() While apparently inherited from coretemp source, this particular error handling cleanup and exit path wasn't copied properly (or perhaps got discarded intermediately and not re-added properly later). Signed-off-by: Jan Beulich <jbeulich@novell.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> (added device file removal in pkgtemp_remove)
* | | x86/hwmon: avoid deadlock on CPU removal in pkgtempJan Beulich2010-09-241-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | pkgtemp_device_remove(), holding the list protecting mutex, calls pkgtemp_device_add(), which itself wants to acquire the same mutex. Holding the mutex over the entire loop body in pkgtemp_device_remove() isn't really necessary, as long as the loop gets exited after processing the matched CPU. Once exiting the loop after removing an eventual match, there's no need for using the "safe" list iterator anymore. Signed-off-by: Jan Beulich <jbeulich@novell.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* | | x86/hwmon: fix module init for hotplug-but-no-device-found caseJan Beulich2010-09-241-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In commit 0dca94baeab4a1a514841b0a4c8e3a51dfb4d5ae the call to platform_driver_unregister() was made conditional upon !HOTPLUG_CPU, but the return value from coretemp_init() was left to indicate an error. This isn't correct, as the negative return value indicates to the module loader that initialization failed, which isn't intended here and results in dangling pointers. Signed-off-by: Jan Beulich <jbeulich@novell.com> Cc: Chen Gong <gong.chen@linux.intel.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* | | hwmon: (lis3) Fix Oops with NULL platform dataTakashi Iwai2010-09-241-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The recent addition of threaded irq handler causes a NULL dereference when used with hp_accel driver, which has NULL pdata. Acked-by: Samu Onkalo <samu.p.onkalo@nokia.com> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* | | hwmon: (lm95241) Replace rate sysfs attribute with update_intervalGuenter Roeck2010-09-171-10/+11
| | | | | | | | | | | | | | | | | | | | | | | | update_interval is the matching attribute defined in the hwmon sysfs ABI. Use it. Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
* | | hwmon: (adm1031) Replace update_rate sysfs attribute with update_intervalGuenter Roeck2010-09-171-19/+24
| | | | | | | | | | | | | | | | | | | | | | | | The attribute reflects an interval, not a rate. Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Acked-by: Ira W. Snyder <iws@ovro.caltech.edu> Signed-off-by: Jean Delvare <khali@linux-fr.org>
* | | hwmon: (w83627ehf) Use proper exit sequenceJonas Jonsson2010-09-171-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | According to the datasheet for Winbond W83627DHG the proper way to exit the Extended Function Mode is to write 0xaa to the EFER(0x2e or 0x4e). Signed-off-by: Jonas Jonsson <jonas@ludd.ltu.se> Signed-off-by: Jean Delvare <khali@linux-fr.org>
* | | hwmon: (emc1403) Remove unnecessary hwmon_device_unregisterYong Wang2010-09-171-1/+0Star
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It is unnecessary and wrong to call hwmon_device_unregister in error handling before hwmon_device_register is called. Signed-off-by: Yong Wang <yong.y.wang@intel.com> Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com> Cc: stable@kernel.org Signed-off-by: Jean Delvare <khali@linux-fr.org>
* | | hwmon: (f75375s) Do not overwrite values read from registersGuillem Jover2010-09-171-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All bits in the values read from registers to be used for the next write were getting overwritten, avoid doing so to not mess with the current configuration. Signed-off-by: Guillem Jover <guillem@hadrons.org> Cc: Riku Voipio <riku.voipio@iki.fi> Cc: stable@kernel.org Signed-off-by: Jean Delvare <khali@linux-fr.org>
* | | hwmon: (f75375s) Shift control mode to the correct bit positionGuillem Jover2010-09-171-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The spec notes that fan0 and fan1 control mode bits are located in bits 7-6 and 5-4 respectively, but the FAN_CTRL_MODE macro was making the bits shift by 5 instead of by 4. Signed-off-by: Guillem Jover <guillem@hadrons.org> Cc: Riku Voipio <riku.voipio@iki.fi> Cc: stable@kernel.org Signed-off-by: Jean Delvare <khali@linux-fr.org>
* | | hwmon: (lis3lv02d) Prevent NULL pointer dereferenceKuninori Morimoto2010-09-172-4/+4
|/ / | | | | | | | | | | | | | | | | | | If CONFIG_PM was selected and lis3lv02d_platform_data was NULL, the kernel will be panic when halt command run. Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by: Samu Onkalo <samu.p.onkalo@nokia.com> Sigend-off-by: Jean Delvare <khali@linux-fr.org>
* | hp_accel: add quirks for HP ProBook 532x and HP Mini 5102Takashi Iwai2010-09-101-0/+2
| | | | | | | | | | | | | | | | | | | | Added missing axis-mapping for HP ProBook 532x and HP Mini 5102. Signed-off-by: Takashi Iwai <tiwai@suse.de> Cc: Eric Piel <eric.piel@tremplin-utc.net> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | hwmon: (k8temp) Differentiate between AM2 and ASB1Andreas Herrmann2010-08-251-3/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 8bf0223ed515be24de0c671eedaff49e78bebc9c (hwmon, k8temp: Fix temperature reporting for ASB1 processor revisions) fixed temperature reporting for ASB1 CPUs. But those CPU models (model 0x6b, 0x6f, 0x7f) were packaged both as AM2 (desktop) and ASB1 (mobile). Thus the commit leads to wrong temperature reporting for AM2 CPU parts. The solution is to determine the package type for models 0x6b, 0x6f, 0x7f. This is done using BrandId from CPUID Fn8000_0001_EBX[15:0]. See "Constructing the processor Name String" in "Revision Guide for AMD NPT Family 0Fh Processors" (Rev. 3.46). Cc: Rudolf Marek <r.marek@assembler.cz> Cc: stable@kernel.org [.32.x, .33.x, .34.x, .35.x] Reported-by: Vladislav Guberinic <neosisani@gmail.com> Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
* | hwmon: (ads7871) Fix ads7871_probe error pathsAxel Lin2010-08-251-19/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1. remove 'status' variable 2. remove unneeded initialization of 'err' variable 3. return missing error code if sysfs_create_group fail. 4. fix the init sequence as: - check hardware existence - kzalloc for ads7871_data - sysfs_create_group - hwmon_device_register Signed-off-by: Axel Lin <axel.lin@gmail.com> Cc: stable@kernel.org Signed-off-by: Jean Delvare <khali@linux-fr.org>
generated by cgit v1.2.3-55-g7522 (git 2.39.0) at 2024-06-29 20:57:30 +0200