summaryrefslogtreecommitdiffstats
path: root/drivers/media/i2c/adv7842.c
Commit message (Collapse)AuthorAgeFilesLines
...
* [media] adv7842: Composite sync adjustmentMartin Bugge2014-01-071-0/+8
| | | | | | Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: obtain free-run mode from the platform_dataMartin Bugge2014-01-071-3/+8
| | | | | | | | | | | | | The free-run mode can be board-specific. Also updated the platform_data in ezkit to ensure that what was the old default value is now explicitly specified, so the behavior for that board is unchanged. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Cc: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: composite sd-ram test, clear timings before settingMartin Bugge2014-01-071-2/+7
| | | | | | | | Must clear timings before setting after test to recover. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: enable HDMI/DVI mode irqMartin Bugge2014-01-071-10/+26
| | | | | | Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: i2c dummy clients registrationMartin Bugge2014-01-071-20/+63
| | | | | | | | | Clear i2c_clients ptr when unregistered. Warn if configured i2c-addr is zero. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: support g_edid ioctlMartin Bugge2014-01-071-0/+41
| | | | | | Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: restart STDI once if format is not foundMartin Bugge2014-01-071-8/+41
| | | | | | | | | | | | | | | The STDI block may measure wrong values, especially for lcvs and lcf. If the driver can not find any valid timing, the STDI block is restarted to measure the video timings again. The function will return an error, but the restart of STDI will generate a new STDI interrupt and the format detection process will restart. Copied from adv7604. Signed-off-by: Martin Bugge <marbugge@cisco.com> Cc: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: clear edid, if no edid just disable Edid-DDC accessMartin Bugge2014-01-071-2/+5
| | | | | | | Signed-off-by: Martin Bugge <marbugge@cisco.com> Cc: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: mute audio before switching inputs to avoid noise/popsMats Randgaard2014-01-071-7/+16
| | | | | | Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: Use defines to select EDID portMats Randgaard2014-01-071-43/+34Star
| | | | | | Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: remove connector type. Never used for anything usefulMats Randgaard2014-01-071-4/+0Star
| | | | | | | | May also be wrong if the receiver is connected to more than one connector. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: increase wait timeMartin Bugge2014-01-071-1/+1
| | | | | | | | | | Wait 5ms after main reset. The data-sheet doesn't specify the wait after i2c-controlled reset, so using same value as after pin-controlled reset. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: set default input in platform-dataMartin Bugge2014-01-071-1/+1
| | | | | | Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: 625/525 line standard jitter fixMartin Bugge2014-01-071-16/+40
| | | | | | | | | | | | | | | | | | Both the PAL and NTSC standards are interlaced where a frame consist of two fields. Total number of lines in a frame in both systems are an odd number so the two fields will have different length. In the 625 line standard ("PAL") the odd field of the frame is transmitted first, while in the 525 standard ("NTSC") the even field is transmitted first. This adds the possibility to change output config between the fields and standards. This setting will reduce the "format-jitter" on the signal sent by the pixelport moving the difference between the fields to vertical front/back-porch only. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: set defaults spa-locationMartin Bugge2014-01-071-7/+7
| | | | | | | | | | For edid with no Source Physical Address (spa), set spa-location to default and use correct values from edid. Signed-off-by: Martin Bugge <marbugge@cisco.com> Cc: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: support YCrCb analog input, receive CEA formats as RGB on ↵Hans Verkuil2014-01-071-29/+65
| | | | | | | | | | | | | | | | | | | | | | | | | | VGA input Added support for YCrCb analog input. If input is ADV7842_MODE_RGB and RGB quantization range is set to V4L2_DV_RGB_RANGE_AUTO, then video with CEA timings will be received as RGB. For ADV7842_MODE_COMP, automatic CSC mode will be selected. See table 48 on page 281 in "ADV7842 Hardware Manual, Rev. 0, January 2011" for details. Make sure that when switching inputs the RGB quantization range is updated as well. Also updated the platform_data in ezkit to ensure that what was the old default value is now explicitly specified, so the behavior for that board is unchanged. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Cc: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: added DE vertical position in SDP-io-syncMartin Bugge2014-01-071-0/+4
| | | | | | Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: save platform data in state structMartin Bugge2014-01-071-1/+5
| | | | | | Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: properly enable/disable the irqsMartin Bugge2014-01-071-7/+4Star
| | | | | | | | | | | | | | The method of disabling the irq-output pin caused many "empty" interrupts. Instead, actually disable/enable the interrupts by changing the interrupt masks. Also enable STORE_MASKED_IRQ in INT1 configuration, otherwise when HDMI events happen while the interrupt is masked those events will be ignored when the interrupt is unmasked. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: corrected setting of cp-register 0x91 and 0x8fMartin Bugge2014-01-071-2/+2
| | | | | | | | | | | | Bit 6 of register 0x8f was cleared incorrectly (must be 1), and bit 4 of register 0x91 was set incorrectly (must be 0). These bits are undocumented, so we shouldn't modify them to values different from what the datasheet specifies. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: Re-worked query_dv_timings()Martin Bugge2014-01-071-77/+35Star
| | | | | | | | This simplified the code quite a bit. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] media_tree: Fix spelling errorsJonathan McCrohan2013-11-291-1/+1
| | | | | | | | | | | | Fix various spelling errors in strings and comments throughout the media tree. The majority of these were found using Lucas De Marchi's codespell tool. [m.chehab@samsung.com: discard hunks with conflicts] Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: fix compilation with GCC < 4.4.6Gianluca Gennari2013-10-141-18/+12Star
| | | | | | Signed-off-by: Gianluca Gennari <gennarone@gmail.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* [media] adv7842: add new video decoder driverHans Verkuil2013-08-261-0/+2946
This is a Analog Devices Component/Graphics/SD Digitizer with 2:1 Multiplexed HDMI Receiver. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
generated by cgit v1.2.3-55-g7522 (git 2.39.0) at 2024-11-01 16:26:12 +0100