summaryrefslogtreecommitdiffstats
path: root/drivers/mmc/host
Commit message (Collapse)AuthorAgeFilesLines
* mmc: sdhci-of-at91: use SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST quirkludovic.desroches@atmel.com2015-10-081-0/+1
| | | | | | | | | | The Atmel sdhci device needs the SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST quirk. Without it, the internal clock could never stabilised when changing the sd clock frequency. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci: add quirk SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RSTludovic.desroches@atmel.com2015-10-082-0/+7
| | | | | | | | | | | | | The Atmel sdhci device needs a new quirk. sdhci_set_clock set the Clock Control Register to 0 before computing the new value and writing it. It disables the internal clock which causes a reset mecanism. If we write the new value before this reset mecanism is done, it will prevent the stabilisation of the internal clock, so a delay is needed. This delay is about 2-3 cycles of the base clock. To be safe, a 1 ms delay is used. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci-pxav3: fix error handling of armada_38x_quirksMarcin Wojtas2015-10-081-1/+1
| | | | | | | | | | In case of armada_38x_quirks error, all clocks should be cleaned-up, same as after mv_conf_mbus_windows failure. Signed-off-by: Marcin Wojtas <mw@semihalf.com> Cc: <stable@vger.kernel.org> # v4.2 Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci-pxav3: disable clock inversion for HS MMC cardsNadav Haklai2015-10-081-0/+3
| | | | | | | | | | | | According to 'FE-2946959' erratum the clock inversion option is needed to support slow frequencies when the card input hold time requirement is high. This setting is not required for high speed MMC and might cause timing violation. Signed-off-by: Nadav Haklai <nadavh@marvell.com> Cc: <stable@vger.kernel.org> # v4.2 Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci-pxav3: remove broken clock base quirk for Armada 38x sdhci driverNadav Haklai2015-10-081-0/+1
| | | | | | | | | | | | shci-pxav3 driver is enabling by default the SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN quirk. However this quirk is not required for Armada 38x and leads to wrong clock setting in the divider. Signed-off-by: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Marcin Wojtas <mw@semihalf.com> Cc: <stable@vger.kernel.org> # v4.2 Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: host: omap_hsmmc: Fix MMC for omap3 legacy bootingTony Lindgren2015-10-081-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | Starting with commit 7d607f917008 ("mmc: host: omap_hsmmc: use devm_regulator_get_optional() for vmmc") MMC on omap3 stopped working for legacy booting. This is because legacy booting sets up some of the resource in the platform init code, and for optional regulators always seem to return -EPROBE_DEFER for the legacy booting. Let's fix the issue by checking for device tree based booting for now. Then when omap3 boots in device tree only mode, this patch can be just reverted. Fixes: 7d607f917008 ("mmc: host: omap_hsmmc: use devm_regulator_get_optional() for vmmc") Cc: Felipe Balbi <balbi@ti.com> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Nishanth Menon <nm@ti.com> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Tony Lindgren <tony@atomide.com> Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* Revert "mmc: host: omap_hsmmc: use regulator_is_enabled to find pbias status"Tony Lindgren2015-10-081-2/+6
| | | | | | | | | | | | | | | | | | | This reverts commit c55d7a0553643a7e8f120688b82b594471084d3c. Without reverting this commit we get "unbalanced disables for pbias_mmc_omap4" errors on omap4430. It seems that 4430 and 4460 behave in a different way for the PBIAS regulator registers and until that has been debugged further we cannot rely on the regulator status registers in hardare on 4430. Fixes: 7d607f917008 ("mmc: host: omap_hsmmc: use devm_regulator_get_optional() for vmmc") Cc: Felipe Balbi <balbi@ti.com> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Nishanth Menon <nm@ti.com> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Tony Lindgren <tony@atomide.com> Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: pxamci: fix card detect with slot-gpio APIRobert Jarzmik2015-09-291-44/+22Star
| | | | | | | | | | | | | | | | Move pxamci to mmc slot-gpio API to fix interrupt request. It fixes the case where the card detection is on a gpio expander, on I2C for example on zylonite board. In this case, the card detect netsted interrupt is called from a threaded interrupt. The request_irq() fails, because a hard irq cannot be a nested interrupt from a threaded interrupt (set __setup_irq()). This was tested on zylonite and mioa701 boards. Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Cc: Petr Cvek <petr.cvek@tul.cz> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sunxi: Fix clk-delay settingsHans de Goede2015-09-291-14/+39
| | | | | | | | | | | | | | | | | | | | | In recent allwinner kernel sources the mmc clk-delay settings have been slightly tweaked, and for sun9i they are completely different then what we are using. This commit brings us in sync with what allwinner does, fixing problems accessing sdcards on some A33 devices (and likely others). For pre sun9i hardware this makes the following changes: -At 400Khz change the sample delay from 7 to 0 (introduced in A31 sdk) -At 50 Mhz change the sample delay from 5 to 4 (introduced in A23 sdk) This also drops the clk-delay calculation for clocks > 50 MHz, we do not need this as we've: mmc->f_max = 50000000, and the delays in the old code were not correct (at 100 MHz the delay must be a multiple of 60, at 200 MHz a multiple of 120). Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: android-goldfish: remove incorrect __iomem annotationChristoph Hellwig2015-09-011-1/+1
| | | | | | | | | | Make sparse happy: drivers/mmc/host/android-goldfish.c:535:56: sparse: incorrect type in argument 3 (different address spaces) Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: host: omap_hsmmc: remove CONFIG_REGULATOR checkKishon Vijay Abraham I2015-08-271-31/+3Star
| | | | | | | | | Now that support for platforms which have optional regulator is added, remove CONFIG_REGULATOR check in omap_hsmmc. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: host: omap_hsmmc: use ios->vdd for setting vmmc voltageKishon Vijay Abraham I2015-08-271-3/+4
| | | | | | | | | | | vdd voltage is set in mmc core to ios->vdd and vmmc should actually be set to this voltage. Modify omap_hsmmc_enable_supply to not take vdd as argument since now it's directly set to the voltage in ios->vdd. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: host: omap_hsmmc: use regulator_is_enabled to find pbias statusKishon Vijay Abraham I2015-08-271-6/+2Star
| | | | | | | | | | Use regulator_is_enabled of pbias regulator to find pbias regulator status instead of maintaining a custom bookkeeping pbias_enabled variable. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: host: omap_hsmmc: enable/disable vmmc_aux regulator based on previous stateKishon Vijay Abraham I2015-08-271-2/+8
| | | | | | | | | enable vmmc_aux regulator only if it is in disabled state and disable vmmc_aux regulator only if it is in enabled state. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: host: omap_hsmmc: don't use ->set_power to set initial regulator stateKishon Vijay Abraham I2015-08-271-10/+56
| | | | | | | | | | | | | If the regulator is enabled on boot (checked using regulator_is_enabled), invoke regulator_enable() so that the usecount reflects the correct state of the regulator and then disable the regulator so that the initial state of the regulator is disabled. Avoid using ->set_power, since set_power also takes care of setting the voltages which is not needed at this point. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: host: omap_hsmmc: avoid pbias regulator enable on power offKishon Vijay Abraham I2015-08-271-4/+4
| | | | | | | | | Fix omap_hsmmc_set_power so that pbias regulator is not enabled during power off. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: host: omap_hsmmc: add separate function to set pbiasKishon Vijay Abraham I2015-08-271-30/+48
| | | | | | | | | No functional change. Cleanup omap_hsmmc_set_power by adding separate functions to set pbias and invoke it from omap_hsmmc_set_power. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: host: omap_hsmmc: add separate functions for enable/disable supplyKishon Vijay Abraham I2015-08-271-35/+66
| | | | | | | | | | No functional change. Cleanup omap_hsmmc_set_power by adding separate functions for enable/disable supply and invoke it from omap_hsmmc_set_power. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: host: omap_hsmmc: return error if any of the regulator APIs failKishon Vijay Abraham I2015-08-271-12/+40
| | | | | | | | | | Return error if any of the regulator APIs (regulator_enable, regulator_disable, regulator_set_voltage) fails in omap_hsmmc_set_power to avoid undefined behavior. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: host: omap_hsmmc: remove unnecessary pbias set_voltageKishon Vijay Abraham I2015-08-271-1/+0Star
| | | | | | | | | | Remove the unnecessary pbias regulator_set_voltage done after pbias regulator_disable in omap_hsmmc_set_power. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Roger Quadros <rogerq@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: host: omap_hsmmc: use mmc_host's vmmc and vqmmcKishon Vijay Abraham I2015-08-271-35/+28Star
| | | | | | | | | | | No functional change. Instead of using omap_hsmmc_host's vcc and vcc_aux members, use vmmc and vqmmc present in mmc_host which is present for the same purpose. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Roger Quadros <rogerq@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: host: omap_hsmmc: use the ocrmask provided by the vmmc regulatorKishon Vijay Abraham I2015-08-271-9/+1Star
| | | | | | | | | | | | If the vmmc regulator provides a valid ocrmask, use it. By this even if the pdata has a valid ocrmask, it will be overwritten with the ocrmask of the vmmc regulator. Also remove the unnecessary compatibility check between the ocrmask in the pdata and the ocrmask from the vmmc regulator. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: host: omap_hsmmc: cleanup omap_hsmmc_reg_get()Kishon Vijay Abraham I2015-08-271-22/+16Star
| | | | | | | | | | | | | No functional change. Instead of using a local regulator variable in omap_hsmmc_reg_get() for holding the return value of devm_regulator_get_optional() and then assigning to omap_hsmmc_host regulator members: vcc, vcc_aux and pbias, directly use the omap_hsmmc_host regulator members. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Roger Quadros <rogerq@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: host: omap_hsmmc: return on fatal errors from omap_hsmmc_reg_getKishon Vijay Abraham I2015-08-271-2/+20
| | | | | | | | | | | Now return error only if the return value of devm_regulator_get_optional() is not the same as -ENODEV, since with -EPROBE_DEFER, the regulator can be obtained later and all other errors are fatal. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: host: omap_hsmmc: use devm_regulator_get_optional() for vmmcKishon Vijay Abraham I2015-08-271-3/+7
| | | | | | | | | | | | Since vmmc can be optional for some platforms, use devm_regulator_get_optional() for vmmc. Now return error only if the return value of devm_regulator_get_optional() is not the same as -ENODEV, since with -EPROBE_DEFER, the regulator can be obtained later and all other errors are fatal. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci-of-at91: fix platform_no_drv_owner.cocci warningskbuild test robot2015-08-271-1/+0Star
| | | | | | | | | | Remove .owner field if calls are used which set it automatically Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci CC: ludovic.desroches@atmel.com <ludovic.desroches@atmel.com> Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sh_mmcif: Fix suspend processKoji Matsuoka2015-08-271-0/+2
| | | | | | | | The clock should be enable when SDHI registers are accessed. Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com> Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: usdhi6rol0: fix error return codeJulia Lawall2015-08-271-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Propagate error code on failure. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ identifier ret; expression e1,e2; @@ ( if (\(ret < 0\|ret != 0\)) { ... return ret; } | ret = 0 ) ... when != ret = e1 when != &ret *if(...) { ... when != ret = e2 when forall return ret; } // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: omap: fix error return codeJulia Lawall2015-08-271-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Return a negative error code on failure. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ identifier ret; expression e1,e2; @@ ( if (\(ret < 0\|ret != 0\)) { ... return ret; } | ret = 0 ) ... when != ret = e1 when != &ret *if(...) { ... when != ret = e2 when forall return ret; } // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: usdhi6rol0: fix ack register writeRabin Vincent2015-08-271-1/+1
| | | | | | | | | | The intent appears to be to clear only the bits which are set in status (by setting them to zero in the ack write), like in the other interrupt handlers, and not to always clear everything (by always writing zero). Use the correct not operator. Signed-off-by: Rabin Vincent <rabin.vincent@axis.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: usdhi6rol0: fix NULL pointer deref in debug printRabin Vincent2015-08-271-1/+2
| | | | | | | | | host->sg is only set when we're transferring multiple blocks. Check for its availibility before dereferencing it in the timeout work debug print. Signed-off-by: Rabin Vincent <rabin.vincent@axis.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: usdhi6rol0: handle probe deferral for regulatorRabin Vincent2015-08-271-2/+4
| | | | | | | | | | | We ignore errors from mmc_regulator_get_supply() because the usage of the regulators is optional for the driver, but we still need to check for and handle EPROBE_DEFER, like it's done in for example dw_mmc. Otherwise we might end up not using the specified regulators just because of probe order. Signed-off-by: Rabin Vincent <rabin.vincent@axis.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci-of-arasan: Add the support for sdhci-5.1Shawn Lin2015-08-271-0/+1
| | | | | | | | | | | | This patch adds the compatible string in sdhci-of-arasan.c to support sdhci-arasan5.1 version of controller. No documented controller IP version is found in the TRM, so we use ths version of command queueing engine integrated into this controller by arasan to specify our controller. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci: also get preset value and driver type for MMC_DDR52Jisheng Zhang2015-08-271-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | commit bb8175a8aa42 ("mmc: sdhci: clarify DDR timing mode between SD-UHS and eMMC") added MMC_DDR52 as eMMC's DDR mode to be distinguished from SD-UHS, but it missed setting driver type for MMC_DDR52 timing mode. So sometimes we get the following error on Marvell BG2Q DMP board: [ 1.559598] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00 [ 1.569314] mmcblk0: retrying using single block read [ 1.575676] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0 [ 1.585202] blk_update_request: I/O error, dev mmcblk0, sector 2 [ 1.591818] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0 [ 1.601341] blk_update_request: I/O error, dev mmcblk0, sector 3 This patches fixes this by adding the missing driver type setting. Fixes: bb8175a8aa42 ("mmc: sdhci: clarify DDR timing mode ...") Signed-off-by: Jisheng Zhang <jszhang@marvell.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: atmel-mci: remove useless includeAlexandre Belloni2015-08-271-1/+0Star
| | | | | | | | | Definitions from linux/platform_data/atmel.h are not used, remove the include. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sunxi: fix timeout in sunxi_mmc_oclk_onoffMichal Suchanek2015-08-271-1/+1
| | | | | | | | | | | | | | | | | | The 250ms timeout is too short. On my system enabling the oclk takes under 50ms and disabling slightly over 100ms when idle. Under load disabling the clock can take over 350ms. This does not make mmc clock gating look like good option to have on sunxi but the system should not crash with mmc clock gating enabled nonetheless. This patch sets the timeout to 750ms. Signed-off-by: Michal Suchanek <hramrach@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci-sirf: corrent quirk according to real chipsBarry Song2015-08-271-2/+2
| | | | | | | | the current quirk set is for an old FPGA, and this patch corrects quirks according to real SoC. Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci-esdhc-imx: change default watermark level and burst lengthHaibo Chen2015-08-271-1/+2
| | | | | | | | | | | | | | | | | | | | | | | By default, for all imx SoC types, the watermark level is 16, and the burst length is 8. But if the SDIO/SD/MMC I/O speed is fast enough, this default watermark level and burst length will be the performance bottleneck. For example, i.MX7D support eMMC HS400 mode, this mode can run in 8 bit, 200MHZ DDR mode. So the I/O speed improve a lot compare to SD3.0. The default burst length is 8, if we don't change this value, in HS400 mode, when we do eMMC read operation, we can find that the clock signal will stop for a period of time. This means the speed of data moving on AHB bus is slower than I/O speed. So we should improve the speed of data moving on AHB bus. This patch set the default burst length as 16, and set the default watermark level as 64. The test result is the clock signal has no stop during the eMMC HS400 operation. Signed-off-by: Haibo Chen <haibo.chen@freescale.com> Acked-by: Dong Aisheng <aisheng.dong@freescale.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci-esdhc-imx: set back the burst_length_enable bit to 1Haibo Chen2015-08-271-0/+16
| | | | | | | | | | | | | Currently we find that if a usdhc is choosed to boot system, then ROM code will set the burst length enable bit of this usdhc as 0. This will make performance drop a lot if this usdhc's burst length is configed. So this patch set back the burst_length_enable bit as 1, which is the default value, and means burst length is enabled for INCR. Signed-off-by: Haibo Chen <haibo.chen@freescale.com> Acked-by: Dong Aisheng <aisheng.dong@freescale.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci-esdhc-imx: add tuning-step setting supportHaibo Chen2015-08-271-0/+9
| | | | | | | | | | | | | | tuning-step is the delay cell steps in tuning procedure. The default value of tuning-step is 1. Some boards or cards need another value to pass the tuning procedure. For example, imx7d-sdb board need the tuning-step value as 2, otherwise it can't pass the tuning procedure. So this patch add the tuning-step setting in driver, so that user can set the tuning-step value in dts. Signed-off-by: Haibo Chen <haibo.chen@freescale.com> Acked-by: Dong Aisheng <aisheng.dong@freescale.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci-esdhc-imx: add imx7d support and support HS400Haibo Chen2015-08-271-3/+83
| | | | | | | | | | | | The imx7d usdhc is derived from imx6sx, the difference is that imx7d support HS400. So introduce a new compatible string for imx7d and add HS400 support for imx7d usdhc. Signed-off-by: Haibo Chen <haibo.chen@freescale.com> Acked-by: Dong Aisheng <aisheng.dong@freescale.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci-of-esdhc: add workaround for pre divider initial valueYangbo Lu2015-08-271-0/+6
| | | | | | | | | | For eSDHC(version < 2.3), the pre divider only could divide base clock by 2 at least. Add workaround for this to avoid unexpected issue. Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Fixes: bd455029d01c ("mmc: sdhci-of-esdhc: Pre divider starts at 1") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci: fix dma memory leak in sdhci_pre_req()Haibo Chen2015-08-272-46/+29Star
| | | | | | | | | | | | | | | | | | | | Currently one mrq->data maybe execute dma_map_sg() twice when mmc subsystem prepare over one new request, and the following log show up: sdhci[sdhci_pre_dma_transfer] invalid cookie: 24, next-cookie 25 In this condition, mrq->date map a dma-memory(1) in sdhci_pre_req for the first time, and map another dma-memory(2) in sdhci_prepare_data for the second time. But driver only unmap the dma-memory(2), and dma-memory(1) never unmapped, which cause the dma memory leak issue. This patch use another method to map the dma memory for the mrq->data which can fix this dma memory leak issue. Fixes: 348487cb28e6 ("mmc: sdhci: use pipeline mmc requests to improve performance") Reported-and-tested-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Haibo Chen <haibo.chen@freescale.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci-pci: set the clear transfer mode register quirk for O2MicroAdam Lee2015-08-271-0/+1
| | | | | | | | | | | This patch fixes MMC not working issue on O2Micro/BayHub Host, which requires transfer mode register to be cleared when sending no DMA command. Signed-off-by: Peter Guo <peter.guo@bayhubtech.com> Signed-off-by: Adam Lee <adam.lee@canonical.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: tmio: Fix timeout value for command requestTakeshi Kihara2015-08-241-2/+4
| | | | | | | | | | | | Fix the problem which timeout occurs at the time of command request with several cards. The timeout value was insufficient as a verification of several cards, so it was changed 5 seconds from 2 seconds. Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com> Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci-of-at91: introduce driver for the Atmel SDMMCludovic.desroches@atmel.com2015-08-243-0/+201
| | | | | | | | Introduce driver for he Atmel SDMMC available on sama5d2. It is a sdhci compliant controller. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdhci: switch from programmable clock mode to divided one if neededludovic.desroches@atmel.com2015-08-241-9/+20
| | | | | | | | | In programmable mode, if the clock frequency is too high, the divider can be too small to meet the clock frequency requirement especially to init the SD card. In this case, switch to the divided clock mode. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: add quirk for broken data transfer over schemeAddy Ke2015-08-172-2/+65
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch add a new quirk to add a s/w timer to notify the driver to terminate current transfer and report a data timeout to the core, if DTO interrupt does NOT come within the given time. dw_mmc call mmc_request_done func to finish transfer depends on DTO interrupt. If DTO interrupt does not come in sending data state, the current transfer will be blocked. We got the reply from synopsys: There are two counters but both use the same value of [31:8] bits. Data timeout counter doesn't wait for stop clock and you should get DRTO even when the clock is not stopped. Host Starvation timeout counter is triggered with stop clock condition. This means that host should get DRTO and DTO interrupt. But this case really exists, when driver reads tuning data from card on RK3288-pink2 board. I measured waveforms by oscilloscope and found that card clock was always on and data lines were always holded high level in sending data state. There are two possibility that data over interrupt doesn't come in reading data state on RK3X SoCs: - get command done interrupt, but doesn't get any data-related interrupt. - get data error interrupt, but doesn't get data over interrupt. Signed-off-by: Addy Ke <addy.ke@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
* mmc: dw_mmc: print the message for deprecated propertyJaehoon Chung2015-08-171-1/+3
| | | | | | | supports-highspeed was deprecated. If someone use it, we need to notice information for it. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
* mmc: dw_mmc: remove the unused blk_settingJaehoon Chung2015-08-171-21/+13Star
| | | | | | "blk_setting" doesn't use anywhere. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
generated by cgit v1.2.3-55-g7522 (git 2.39.0) at 2024-07-09 18:14:55 +0200