summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/freescale/fec.h
Commit message (Collapse)AuthorAgeFilesLines
* net: fec: ptp: fix convergence issue to support LinuxPTP stackNimrod Andy2014-10-151-0/+50
| | | | | | | | | | | | | | | | | | | | | | | | | | | | iMX6SX IEEE 1588 module has one hw issue in capturing the ATVR register. The current SW flow is: ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK; ts_counter_ns = ENET0->ATVR; The ATVR value is not expected value that cause LinuxPTP stack cannot be convergent. ENET Block Guide/ Chapter for the iMX6SX (PELE) address the issue: After set ENET_ATCR[Capture], there need some time cycles before the counter value is capture in the register clock domain. The wait-time-cycles is at least 6 clock cycles of the slower clock between the register clock and the 1588 clock. So need something like: ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK; wait(); ts_counter_ns = ENET0->ATVR; For iMX6SX, the 1588 ts_clk is fixed to 25Mhz, register clock is 66Mhz, so the wait-time-cycles must be greater than 240ns (40ns * 6). The patch add 1us delay before cpu read ATVR register. Changes V2: Modify the commit/comments log to describe the issue clearly. Signed-off-by: Fugang Duan <B38611@freescale.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: ptp: Enable PPS output based on ptp clockLuwei Zhou2014-10-141-0/+7
| | | | | | | | | | | | | FEC ptp timer has 4 channel compare/trigger function. It can be used to enable pps output. The pulse would be ouput high exactly on N second. The pulse ouput high on compare event mode is used to produce pulse per second. The pulse width would be one cycle based on ptp timer clock source.Since 31-bit ptp hardware timer is used, the timer will wrap more than 2 seconds. We need to reload the compare compare event about every 1 second. Signed-off-by: Luwei Zhou <b45643@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: ptp: Use hardware algorithm to adjust PTP counter.Luwei Zhou2014-10-141-0/+3
| | | | | | | | | | | The FEC IP supports hardware adjustment for ptp timer. Refer to the description of ENET_ATCOR and ENET_ATINC registers in the spec about the hardware adjustment. This patch uses hardware support to adjust the ptp offset and frequency on the slave side. Signed-off-by: Luwei Zhou <b45643@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: Fugang Duan <b38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: implement rx_copybreak to improve rx performanceNimrod Andy2014-10-021-0/+2
| | | | | | | | | | | | | | | | | | | - Copy short frames and keep the buffers mapped, re-allocate skb instead of memory copy for long frames. - Add support for setting/getting rx_copybreak using generic ethtool tunable Changes V3: * As Eric Dumazet's suggestion that removing the copybreak module parameter and only keep the ethtool API support for rx_copybreak. Changes V2: * Implements rx_copybreak * Rx_copybreak provides module parameter to change this value * Add tunable_ops support for rx_copybreak Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: Add Ftype to BD to distiguish three tx queues for AVBNimrod Andy2014-09-261-0/+1
| | | | | | | | | | | | | The current driver loss Ftype field init for BD, which cause tx queue #1 and #2 cannot work well. Add Ftype field to BD to distiguish three queues for AVB: 0 -> Best Effort 1 -> ClassA 2 -> ClassB Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net:fec: increase DMA queue numberFugang Duan2014-09-191-1/+1
| | | | | | | when enable interrupt coalesce, 8 BD is not enough. Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: add interrupt coalescence feature supportFugang Duan2014-09-191-0/+15
| | | | | | | | | | | | | | | | | i.MX6 SX support interrupt coalescence feature By default, init the interrupt coalescing frame count threshold and timer threshold. Supply the ethtool interfaces as below for user tuning to improve enet performance: rx_max_coalesced_frames rx_coalesce_usecs tx_max_coalesced_frames tx_coalesce_usecs Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: fix build error at m68k platformFrank Li2014-09-161-5/+25
| | | | | | | | | | | | | | | | | | | | | | | reproduce: wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross git checkout 4d494cdc92b3b9a0f5fb9e1560810fa27d5a0489 make.cross ARCH=m68k m5272c3_defconfig make.cross ARCH=m68k drivers/net/ethernet/freescale/fec.h:262:0: warning: "FEC_R_DES_START" redefined #define FEC_R_DES_START(X) ((X == 1) ? FEC_R_DES_START_1 : \ ^ drivers/net/ethernet/freescale/fec.h:158:0: note: this is the location of the previous definition #define FEC_R_DES_START 0x3d0 /* Receive descriptor ring */ ^ drivers/net/ethernet/freescale/fec.h:265:0: warning: "FEC_X_DES_START" redefined #define FEC_X_DES_START(X) ((X == 1) ? FEC_X_DES_START_1 : \ ... Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: change FEC alignment according to i.mx6 sx requirementFugang Duan2014-09-131-0/+3
| | | | | | | | | | | i.MX6 SX change FEC alignment requirement. i.MX6 SX change internal bus from AHB to AXI. It require RX buffer must be 64 bytes alignment. And remove TX buffer alignment requirement. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: add enet-avb IP supportFrank Li2014-09-131-0/+33
| | | | | | | | | | | | | | | | | i.MX6SX Enet-AVB support 3 tx queues, 3 rx queues. For tx queues: ring 0 -> best effort ring 1 -> Class A ring 2 -> Class B For rx queues: ring 0 -> best effort ring 1 -> receive VLAN packet with classification match ring 2 -> receive VLAN packet with classification match Add enet-avb IP multiqueue support for the driver. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: parser max queue number from dt fileFugang Duan2014-09-131-0/+2
| | | | | | | | | | | | | | By default, the tx/rx queue number is 1, user can config the queue number at DTS file like this: fsl,num-tx-queues=<3>; fsl,num-rx-queues=<3> Since i.MX6SX enet-AVB IP support multi queues, so use multi queues interface to allocate and set up an Ethernet device. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: change data structure to support multiqueueFugang Duan2014-09-131-24/+91
| | | | | | | | | | | | | | | This patch just change data structure to support multi-queue. Only 1 queue enabled. Ethernet multiqueue mechanism can improve performance in SMP system. For single hw queue, multiqueue can balance cpu loading. For multi hw queues, multiple cores can process network packets in parallel, and refer the article for the detail advantage for multiqueue: http://vger.kernel.org/~davem/davem_nyc09.pdf Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Frank Li <frank.li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net:fec: add enet refrence clock for i.MX 6SX chipFugang Duan2014-09-131-0/+1
| | | | | | | | | | | | | | | | | | | | | i.MX6sx enet has below clocks for user config: clk_ipg: ipg_clk_s, ipg_clk_mac0_s, 66Mhz clk_ahb: enet system clock, it is enet AXI clock for imx6sx. For imx6sx, it alos is the clock source of interrupt coalescing. The clock range: 200Mhz ~ 266Mhz. clk_ref: refrence clock for tx and rx. For imx6sx enet RGMII mode, the refrence clock is 125Mhz coming from internal PLL or external. In i.MX6sx-arm2 board, the clock is from internal PLL. clk_ref is optional, depends on board. clk_enet_out: The clock can be output from internal PLL. It can supply 50Mhz clock for phy. clk_enet_out is optional, depends on chip and board. clk_ptp: 1588 ts clock. It is optional, depends on chip. The patch add clk_ref to distiguish the different clocks. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: ptp: avoid register access when ipg clock is disabledNimrod Andy2014-08-221-1/+4
| | | | | | | | | | | | | | | | | | | | The current kernel hang on i.MX6SX with rootfs mount from MMC. The root cause is that ptp uses a periodic timer to access enet register even if ipg clock is disabled. FEC ptp driver start one period timer to read 1588 counter register in the ptp init function that is called after FEC driver is probed. To save power, after FEC probe finish, FEC driver disable all clocks including ipg clock that is needed for register access. i.MX5x, i.MX6q/dl/sl FEC register access don't cause system hang when ipg clock is disabled, just return zero value. But for i.MX6sx SOC, it cause system hang. To avoid the issue, we need to check ptp clock status before ptp timer count access. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: Support phys probed from devicetree and fixed-linkUwe Kleine-König2014-08-111-0/+1
| | | | | | | | | | This adds support for specifying the phy to be used with the fec in the devicetree using the standard phy-handle property and also supports fixed-link. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: replace delayed work with standard workRussell King2014-07-091-6/+2Star
| | | | | | | | | | | | | | As of "better implementation of iMX6 ERR006358 quirk", we no longer have a requirement for a delayed work. Moreover, the work is now only used for timeout purposes, so the timeout flag is also pointless - we set it each time we queue the work, and the work clears it. Replace the fec_enet_delayed_work struct with a standard work_struct, resulting in simplified timeout handling code. Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: better implementation of iMX6 ERR006358 quirkRussell King2014-07-091-1/+0Star
| | | | | | | | | | | | | | | | | | | | Using a (delayed) workqueue for ERR006358 is not correct - a work queue is a single-trigger device. Once the work queue has been scheduled, it can't be re-scheduled until it has been run. This can cause problems - with an appropriate packet timing, we can end up with packets queued, but not sent by the hardware, resulting in the transmit timeout firing. Re-implement this as per the workaround detailed in the ERR006358 documentation - if there are packets waiting to be sent when we service the transmit ring, and we see that the transmitter is not running, kick the transmitter to run the pending entries in the ring. Testing here with a 10Mbit half duplex link sees the resulting iperf TCP bandwidth increase from between 1 to 2Mbps to between 8 to 9Mbps. Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: remove useless fep->openedRussell King2014-07-081-1/+0Star
| | | | | | | | | | | | | | napi_disable() waits until the NAPI processing has completed, and then prevents any further polls. At this point, the driver then clears fep->opened. The NAPI poll function uses this to stop processing in the receive path. Hence, it will never see this variable cleared, because the NAPI poll has to complete before it will be cleared. Therefore, this variable serves no purpose, so let's remove it. Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: Add software TSO supportNimrod Andy2014-06-121-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | Add software TSO support for FEC. This feature allows to improve outbound throughput performance. Tested on imx6dl sabresd board, running iperf tcp tests shows: - 16.2% improvement comparing with FEC SG patch - 82% improvement comparing with NO SG & TSO patch $ ethtool -K eth0 tso on $ iperf -c 10.192.242.167 -t 3 & [ 3] local 10.192.242.108 port 35388 connected with 10.192.242.167 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0- 3.0 sec 181 MBytes 506 Mbits/sec During the testing, CPU loading is 30%. Since imx6dl FEC Bandwidth is limited to SOC system bus bandwidth, the performance with SW TSO is a milestone. CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> CC: Eric Dumazet <eric.dumazet@gmail.com> CC: David Laight <David.Laight@ACULAB.COM> CC: Li Frank <B20596@freescale.com> Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: Add Scatter/gather supportNimrod Andy2014-06-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Add Scatter/gather support for FEC. This feature allows to improve outbound throughput performance. Tested on imx6dl sabresd board: Running iperf tests shows a 55.4% improvement. $ ethtool -K eth0 sg off $ iperf -c 10.192.242.167 -t 3 & [ 3] local 10.192.242.108 port 52618 connected with 10.192.242.167 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0- 3.0 sec 99.5 MBytes 278 Mbits/sec $ ethtool -K eth0 sg on $ iperf -c 10.192.242.167 -t 3 & [ 3] local 10.192.242.108 port 52617 connected with 10.192.242.167 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0- 3.0 sec 154 MBytes 432 Mbits/sec CC: Li Frank <B20596@freescale.com> Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: Increase buffer descriptor entry numberNimrod Andy2014-06-121-2/+2
| | | | | | | | | | In order to support SG, software TSO, let's increase BD entry number. CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> CC: Eric Dumazet <eric.dumazet@gmail.com> CC: David Laight <David.Laight@ACULAB.COM> Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: Factorize the .xmit transmit functionNimrod Andy2014-06-121-0/+1
| | | | | | | | | | | Make the code more readable and easy to support other features like SG, TSO, moving the common transmit function to one api. And the patch also factorize the getting BD index to it own function. CC: David Laight <David.Laight@ACULAB.COM> Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* fec: Implement the SIOCGHWTSTAMP ioctlBen Hutchings2013-11-211-1/+2
| | | | | | This is untested. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
* net: fec: fix the error to get the previous BD entryDuan Fugang-B386112013-09-041-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Bug: error to get the previous BD entry. When the current BD is the first BD, the previous BD entry must be the last BD, not "bdp - 1" in current logic. V4: * Optimize fec_enet_get_nextdesc() for code clean. Replace "ex_new_bd - ring_size" with "ex_base". Replace "new_bd - ring_size" with "base". V3: * Restore the API name because David suggest to use fec_enet_ prefix for all function in fec driver. So, change next_bd() -> fec_enet_get_nextdesc() change pre_bd() -> fec_enet_get_prevdesc() * Reduce the two APIs parameters for easy to call. V2: * Add tx_ring_size and rx_ring_size to struct fec_enet_private. * Replace api fec_enet_get_nextdesc() with next_bd(). Replace api fec_enet_get_prevdesc() with pre_bd(). * Move all ring size check logic to next_bd() and pre_bd(), which simplifies the code redundancy. V1: * Add BD ring size check to get the previous BD entry in correctly. Reviewed-by: Li Frank <B20596@freescale.com> Signed-off-by: Fugang Duan <B38611@freescale.com> Acked-by: Frank Li <frank.li@freescale.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: workaround stop tx during errata ERR006358Frank Li2013-07-281-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the ready bit in the transmit buffer descriptor (TxBD[R]) is previously detected as not set during a prior frame transmission, then the ENET_TDAR[TDAR] bit is cleared at a later time, even if additional TxBDs were added to the ring and the ENET_TDAR[TDAR] bit is set. This results in frames not being transmitted until there is a 0-to-1 transition on ENET_TDAR[TDAR]. Workarounds: code can use the transmit frame interrupt flag (ENET_EIR[TXF]) as a method to detect whether the ENET has completed transmission and the ENET_TDAR[TDAR] has been cleared. If ENET_TDAR[TDAR] is detected as cleared when packets are queued and waiting for transmit, then a write to the TDAR bit will restart TxBD processing. This case main happen when loading is light. A ethernet package may not send out utile next package put into tx queue. How to test: while [ true ] do ping <IP> -s 10000 -w 4 ping <IP> -s 6000 -w 2 ping <IP> -s 4000 -w 2 ping <IP> -s 10000 -w 2 done You will see below result in overnight test. 6008 bytes from 10.192.242.116: seq=1 ttl=128 time=0.722 ms 4008 bytes from 10.192.242.116: seq=0 ttl=128 time=1001.008 ms 4008 bytes from 10.192.242.116: seq=1 ttl=128 time=1.010 ms 10008 bytes from 10.192.242.116: seq=0 ttl=128 time=0.896 ms After apply this patch, >1000ms delay disappear. Signed-off-by: Frank Li <Frank.Li@freescale.com> Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: Add VLAN receive HW support.Jim Baxter2013-07-041-0/+3
| | | | | | | | This enables the driver to take advantage of the FEC VLAN indicator to improve performance. Signed-off-by: Jim Baxter <jim_baxter@mentor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* fec: Add support for reading RMON registersChris Healy2013-06-271-0/+55
| | | | | | | | | | | Add ethtool operation to read RMON registers. Tested against net-next on i.MX28. v2: make conditional on #ifndef CONFIG_M5272 Signed-off-by: Chris Healy <cphealy@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* fec: Only pass pdev in fec_ptp_init()Fabio Estevam2013-06-071-1/+1
| | | | | | | Passing pdev in fec_ptp_init() is enough, since we can get ndev locally. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* fec: Place the phy regulator in the private structureFabio Estevam2013-05-281-0/+1
| | | | | | | | | | | | Instead of using a local reg_phy structure, let's put it inside the private structure, so that we are able to have access to the regulator structure even when we are outside fec_probe(). This is in preparation for controlling the FEC PHY regulator in the suspend and resume functions. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: fix kernel oops when plug/unplug cable many timesFrank Li2013-05-081-4/+6
| | | | | | | | | | | | | | | | | | | | | reproduce steps 1. flood ping from other machine ping -f -s 41000 IP 2. run below script while [ 1 ]; do ethtool -s eth0 autoneg off; sleep 3;ethtool -s eth0 autoneg on; sleep 4; done; You can see oops in one hour. The reason is fec_restart clear BD but NAPI may use it. The solution is disable NAPI and stop xmit when reset BD. disable NAPI may sleep, so fec_restart can't be call in atomic context. Signed-off-by: Frank Li <Frank.Li@freescale.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Tested-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge tag 'dt-for-linus-2' of ↵Linus Torvalds2013-05-071-0/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC device tree updates (part 2) from Arnd Bergmann: "These are mostly new device tree bindings for existing drivers, as well as changes to the device tree source files to add support for those devices, and a couple of new boards, most notably Samsung's Exynos5 based Chromebook. The changes depend on earlier platform specific updates and touch the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci." * tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits) ARM: exynos: dts: cros5250: add EC device ARM: dts: Add sbs-battery for exynos5250-snow ARM: dts: Add i2c-arbitrator bus for exynos5250-snow ARM: dts: add mshc controller node for Exynos4x12 SoCs ARM: dts: Add chip-id controller node on Exynos4/5 SoC ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree ARM: davinci: da850-evm: add SPI flash support ARM: davinci: da850: override SPI DT node device name ARM: davinci: da850: add SPI1 DT node spi/davinci: add DT binding documentation spi/davinci: no wildcards in DT compatible property ARM: dts: mvebu: Convert mvebu device tree files to 64 bits ARM: dts: mvebu: introduce internal-regs node ARM: dts: mvebu: Convert all the mvebu files to use the range property ARM: dts: mvebu: move all peripherals inside soc ARM: dts: mvebu: fix cpus section indentation ARM: davinci: da850: add EHRPWM & ECAP DT node ARM/dts: OMAP3: fix pinctrl-single configuration ARM: dts: Add OMAP3430 SDP NOR flash memory binding ARM: dts: Add NOR flash bindings for OMAP2420 H4 ...
| * net: freescale: fec: add support for optional enet_out clkWolfram Sang2013-04-041-0/+1
| | | | | | | | | | | | | | | | | | Some MX28 boards need the internal enet_out clock to be enabled. So, do this in the driver iff the clock was referenced via devicetree. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: David S. Miller <davem@davemloft.net>
* | net: fec: Enable imx6 enet checksum acceleration.Jim Baxter2013-04-251-1/+9
|/ | | | | | | | | | | | | | | | | Enables hardware generation of IP header and protocol specific checksums for transmitted packets. Enabled hardware discarding of received packets with invalid IP header or protocol specific checksums. The feature is enabled by default but can be enabled/disabled by ethtool. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Jim Baxter <jim_baxter@mentor.com> Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: restart the FEC when PHY speed changesLucas Stach2013-03-151-0/+1
| | | | | | | | | | | | | Proviously we would only restart the FEC when PHY link or duplex state changed. PHY does not always bring down the link for speed changes, in which case we would not detect any change and keep FEC running. Switching link speed without restarting the FEC results in the FEC being stuck in an indefinite state, generating error conditions for every packet. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: fix build error in no MXC platformFrank Li2013-03-041-8/+7Star
| | | | | | | | | | | | | | | | | | build error cause by Commit ff43da86c69d76a726ffe7d1666148960dc1d108 ("NET: FEC: dynamtic check DMA desc buff type") drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_nextdesc’: drivers/net/ethernet/freescale/fec.c:215:18: error: invalid use of undefined type ‘struct bufdesc_ex’ drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_prevdesc’: drivers/net/ethernet/freescale/fec.c:224:18: error: invalid use of undefined type ‘struct bufdesc_ex’ drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_start_xmit’: drivers/net/ethernet/freescale/fec.c:286:37: error: arithmetic on pointer to an incomplete type drivers/net/ethernet/freescale/fec.c:287:13: error: arithmetic on pointer to an incomplete type drivers/net/ethernet/freescale/fec.c:324:7: error: dereferencing pointer to incomplete type etc.... Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: put tx to napi poll function to fix dead lockFrank Li2013-03-041-3/+0Star
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | up stack ndo_start_xmit already hold lock. fec_enet_start_xmit needn't spin lock. stat_xmit just update fep->cur_tx fec_enet_tx just update fep->dirty_tx Reserve a empty bdb to check full or empty cur_tx == dirty_tx means full cur_tx == dirty_tx +1 means empty So needn't is_full variable. Fix spin lock deadlock ================================= [ INFO: inconsistent lock state ] 3.8.0-rc5+ #107 Not tainted --------------------------------- inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage. ptp4l/615 [HC1[1]:SC0[0]:HE0:SE1] takes: (&(&list->lock)->rlock#3){?.-...}, at: [<8042c3c4>] skb_queue_tail+0x20/0x50 {HARDIRQ-ON-W} state was registered at: [<80067250>] mark_lock+0x154/0x4e8 [<800676f4>] mark_irqflags+0x110/0x1a4 [<80069208>] __lock_acquire+0x494/0x9c0 [<80069ce8>] lock_acquire+0x90/0xa4 [<80527ad0>] _raw_spin_lock_bh+0x44/0x54 [<804877e0>] first_packet_length+0x38/0x1f0 [<804879e4>] udp_poll+0x4c/0x5c [<804231f8>] sock_poll+0x24/0x28 [<800d27f0>] do_poll.isra.10+0x120/0x254 [<800d36e4>] do_sys_poll+0x15c/0x1e8 [<800d3828>] sys_poll+0x60/0xc8 [<8000e780>] ret_fast_syscall+0x0/0x3c *** DEADLOCK *** 1 lock held by ptp4l/615: #0: (&(&fep->hw_lock)->rlock){-.-...}, at: [<80355f9c>] fec_enet_tx+0x24/0x268 stack backtrace: Backtrace: [<800121e0>] (dump_backtrace+0x0/0x10c) from [<80516210>] (dump_stack+0x18/0x1c) r6:8063b1fc r5:bf38b2f8 r4:bf38b000 r3:bf38b000 [<805161f8>] (dump_stack+0x0/0x1c) from [<805189d0>] (print_usage_bug.part.34+0x164/0x1a4) [<8051886c>] (print_usage_bug.part.34+0x0/0x1a4) from [<80518a88>] (print_usage_bug+0x78/0x88) r8:80065664 r7:bf38b2f8 r6:00000002 r5:00000000 r4:bf38b000 [<80518a10>] (print_usage_bug+0x0/0x88) from [<80518b58>] (mark_lock_irq+0xc0/0x270) r7:bf38b000 r6:00000002 r5:bf38b2f8 r4:00000000 [<80518a98>] (mark_lock_irq+0x0/0x270) from [<80067270>] (mark_lock+0x174/0x4e8) [<800670fc>] (mark_lock+0x0/0x4e8) from [<80067744>] (mark_irqflags+0x160/0x1a4) [<800675e4>] (mark_irqflags+0x0/0x1a4) from [<80069208>] (__lock_acquire+0x494/0x9c0) r5:00000002 r4:bf38b2f8 [<80068d74>] (__lock_acquire+0x0/0x9c0) from [<80069ce8>] (lock_acquire+0x90/0xa4) [<80069c58>] (lock_acquire+0x0/0xa4) from [<805278d8>] (_raw_spin_lock_irqsave+0x4c/0x60) [<8052788c>] (_raw_spin_lock_irqsave+0x0/0x60) from [<8042c3c4>] (skb_queue_tail+0x20/0x50) r6:bfbb2180 r5:bf1d0190 r4:bf1d0184 [<8042c3a4>] (skb_queue_tail+0x0/0x50) from [<8042c4cc>] (sock_queue_err_skb+0xd8/0x188) r6:00000056 r5:bfbb2180 r4:bf1d0000 r3:00000000 [<8042c3f4>] (sock_queue_err_skb+0x0/0x188) from [<8042d15c>] (skb_tstamp_tx+0x70/0xa0) r6:bf0dddb0 r5:bf1d0000 r4:bfbb2180 r3:00000004 [<8042d0ec>] (skb_tstamp_tx+0x0/0xa0) from [<803561d0>] (fec_enet_tx+0x258/0x268) r6:c089d260 r5:00001c00 r4:bfbd0000 [<80355f78>] (fec_enet_tx+0x0/0x268) from [<803562cc>] (fec_enet_interrupt+0xec/0xf8) [<803561e0>] (fec_enet_interrupt+0x0/0xf8) from [<8007d5b0>] (handle_irq_event_percpu+0x54/0x1a0) [<8007d55c>] (handle_irq_event_percpu+0x0/0x1a0) from [<8007d740>] (handle_irq_event+0x44/0x64) [<8007d6fc>] (handle_irq_event+0x0/0x64) from [<80080690>] (handle_fasteoi_irq+0xc4/0x15c) r6:bf0dc000 r5:bf811290 r4:bf811240 r3:00000000 [<800805cc>] (handle_fasteoi_irq+0x0/0x15c) from [<8007ceec>] (generic_handle_irq+0x28/0x38) r5:807130c8 r4:00000096 [<8007cec4>] (generic_handle_irq+0x0/0x38) from [<8000f16c>] (handle_IRQ+0x54/0xb4) r4:8071d280 r3:00000180 [<8000f118>] (handle_IRQ+0x0/0xb4) from [<80008544>] (gic_handle_irq+0x30/0x64) r8:8000e924 r7:f4000100 r6:bf0ddef8 r5:8071c974 r4:f400010c r3:00000000 [<80008514>] (gic_handle_irq+0x0/0x64) from [<8000e2e4>] (__irq_svc+0x44/0x5c) Exception stack(0xbf0ddef8 to 0xbf0ddf40) Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: add napi support to improve proformanceFrank Li2013-01-291-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add napi support Before this patch iperf -s -i 1 ------------------------------------------------------------ Server listening on TCP port 5001 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 4] local 10.192.242.153 port 5001 connected with 10.192.242.138 port 50004 [ ID] Interval Transfer Bandwidth [ 4] 0.0- 1.0 sec 41.2 MBytes 345 Mbits/sec [ 4] 1.0- 2.0 sec 43.7 MBytes 367 Mbits/sec [ 4] 2.0- 3.0 sec 42.8 MBytes 359 Mbits/sec [ 4] 3.0- 4.0 sec 43.7 MBytes 367 Mbits/sec [ 4] 4.0- 5.0 sec 42.7 MBytes 359 Mbits/sec [ 4] 5.0- 6.0 sec 43.8 MBytes 367 Mbits/sec [ 4] 6.0- 7.0 sec 43.0 MBytes 361 Mbits/sec After this patch [ 4] 2.0- 3.0 sec 51.6 MBytes 433 Mbits/sec [ 4] 3.0- 4.0 sec 51.8 MBytes 435 Mbits/sec [ 4] 4.0- 5.0 sec 52.2 MBytes 438 Mbits/sec [ 4] 5.0- 6.0 sec 52.1 MBytes 437 Mbits/sec [ 4] 6.0- 7.0 sec 52.1 MBytes 437 Mbits/sec [ 4] 7.0- 8.0 sec 52.3 MBytes 439 Mbits/sec Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: enable pause frame to improve rx prefomance for 1G networkFrank Li2013-01-181-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The limition of imx6 internal bus cause fec can't achieve 1G perfomance. There will be many packages lost because FIFO over run. This patch enable pause frame flow control. Before this patch iperf -s -i 1 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 4] local 10.192.242.153 port 5001 connected with 10.192.242.94 port 49773 [ ID] Interval Transfer Bandwidth [ 4] 0.0- 1.0 sec 6.35 MBytes 53.3 Mbits/sec [ 4] 1.0- 2.0 sec 3.39 MBytes 28.5 Mbits/sec [ 4] 2.0- 3.0 sec 2.63 MBytes 22.1 Mbits/sec [ 4] 3.0- 4.0 sec 1.10 MBytes 9.23 Mbits/sec ifconfig RX packets:46195 errors:1859 dropped:1 overruns:1859 frame:1859 After this patch iperf -s -i 1 [ 4] local 10.192.242.153 port 5001 connected with 10.192.242.94 port 49757 [ ID] Interval Transfer Bandwidth [ 4] 0.0- 1.0 sec 49.8 MBytes 418 Mbits/sec [ 4] 1.0- 2.0 sec 50.1 MBytes 420 Mbits/sec [ 4] 2.0- 3.0 sec 47.5 MBytes 399 Mbits/sec [ 4] 3.0- 4.0 sec 45.9 MBytes 385 Mbits/sec [ 4] 4.0- 5.0 sec 44.8 MBytes 376 Mbits/sec ifconfig RX packets:2348454 errors:0 dropped:16 overruns:0 frame:0 Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* NET: FEC: dynamtic check DMA desc buff typeFrank Li2013-01-051-10/+6Star
| | | | | | | | | | | | | MX6 and mx28 support enhanced DMA descriptor buff to support 1588 ptp. But MX25, MX3x, MX5x can't support enhanced DMA descriptor buff. Check fec type and choose correct DMA descriptor buff type. Remove static config CONFIG_FEC_PTP. ptp function will be auto detected. Signed-off-by: Frank Li <Frank.Li@freescale.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* FEC: Add time stamping code and a PTP hardware clockFrank Li2012-11-011-0/+38
| | | | | | | | | | | This patch adds a driver for the FEC(MX6) that offers time stamping and a PTP haderware clock. Because FEC\ENET(MX6) hardware frequency adjustment is complex, we have implemented this in software by changing the multiplication factor of the timecounter. Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: move fec_enet_private to header fileFrank Li2012-11-011-0/+81
| | | | | | | | A new file fec_ptp.c will use fec_enet_private to support 1588 PTP move such structure to common header file fec.h Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fsl: fec: handle 10Mbps speed in RMII modeEric Benard2012-01-131-0/+4
| | | | | | | | | | when the link is 10 Mbps and the mode is RMII, it's necessary to set FRCONT to 1 in MIIGSK_CFGR to divide the RMII source clock by 10 in order to support 10 Mbps operations. Signed-off-by: Eric Bénard <eric@eukrea.com> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* freescale: Move the Freescale driversJeff Kirsher2011-08-121-0/+148
Move the Freescale drivers into drivers/net/ethernet/freescale/ and make the necessary Kconfig and Makefile changes. CC: Sandeep Gopalpet <sandeep.kumar@freescale.com> CC: Andy Fleming <afleming@freescale.com> CC: Shlomi Gridish <gridish@freescale.com> CC: Li Yang <leoli@freescale.com> CC: Pantelis Antoniou <pantelis.antoniou@gmail.com> CC: Vitaly Bordug <vbordug@ru.mvista.com> CC: Dan Malek <dmalek@jlc.net> CC: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
generated by cgit v1.2.3-55-g7522 (git 2.39.0) at 2024-07-21 10:29:18 +0200