| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
| |
when build_skb failed, we should goto refill the buffer.
Signed-off-by: Weidong Wang <wangweidong1@huawei.com>
Acked-by: Ding Tainhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
| |
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
| |
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The code sets the expiry value of the timer to a relative value and
starts it with hrtimer_start_expires. That's fine, but that only works
once. The timer is started in relative mode, so the expiry value gets
overwritten with the absolut expiry time (now + expiry).
So once the timer expired, a new call to hrtimer_start_expires results
in an immidiately expired timer, because the expiry value is
already in the past.
Use the proper mechanisms to (re)start the timer in the intended way.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: dingtianhong <dingtianhong@huawei.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: netdev@vger.kernel.org
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
The hip04 ethernet driver causes a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/hisilicon/hip04_eth.o
see include/linux/module.h for more information
This adds the license as "GPL", which matches the header of the file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
| |
The if block was supposed to have curly braces. In the current code we
complain about dropped rx packets when we shouldn't.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
Support Hisilicon hip04 ethernet driver, including 100M / 1000M controller.
The controller has no tx done interrupt, reclaim xmitted buffer in the poll.
v13: Fix the problem of alignment parameters for function and checkpatch warming.
v12: According Alex's suggestion, modify the changelog and add MODULE_DEVICE_TABLE
for hip04 ethernet.
v11: Add ethtool support for tx coalecse getting and setting, the xmit_more
is not supported for this patch, but I think it could work for hip04,
will support it later after some tests for performance better.
Here are some performance test results by ping and iperf(add tx_coalesce_frames/users),
it looks that the performance and latency is more better by tx_coalesce_frames/usecs.
- Before:
$ ping 192.168.1.1 ...
=== 192.168.1.1 ping statistics ===
24 packets transmitted, 24 received, 0% packet loss, time 22999ms
rtt min/avg/max/mdev = 0.180/0.202/0.403/0.043 ms
$ iperf -c 192.168.1.1 ...
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 1.0 sec 115 MBytes 945 Mbits/sec
- After:
$ ping 192.168.1.1 ...
=== 192.168.1.1 ping statistics ===
24 packets transmitted, 24 received, 0% packet loss, time 22999ms
rtt min/avg/max/mdev = 0.178/0.190/0.380/0.041 ms
$ iperf -c 192.168.1.1 ...
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 1.0 sec 115 MBytes 965 Mbits/sec
v10: According David Miller and Arnd Bergmann's suggestion, add some modification
for v9 version
- drop the workqueue
- batch cleanup based on tx_coalesce_frames/usecs for better throughput
- use a reasonable default tx timeout (200us, could be shorted
based on measurements) with a range timer
- fix napi poll function return value
- use a lockless queue for cleanup
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
