summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/mellanox/mlx4/cmd.c
Commit message (Collapse)AuthorAgeFilesLines
* ethernet :mellanox :mlx4: Replace pci_pool_alloc by pci_pool_zallocSouptick Joarder2016-11-301-4/+2Star
| | | | | | | | | | In mlx4_alloc_cmd_mailbox(), pci_pool_alloc() followed by memset will be replaced by pci_pool_zalloc() Signed-off-by: Souptick joarder <jrdr.linux@gmail.com> Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_core: Do not access comm channel if it has not yet been initializedJack Morgenstein2016-10-291-0/+9
| | | | | | | | | | | | | | | | | | | | | | | In the Hypervisor, there are several FW commands which are invoked before the comm channel is initialized (in mlx4_multi_func_init). These include MOD_STAT_CONFIG, QUERY_DEV_CAP, INIT_HCA, and others. If any of these commands fails, say with a timeout, the Hypervisor driver enters the internal error reset flow. In this flow, the driver attempts to notify all slaves via the comm channel that an internal error has occurred. Since the comm channel has not yet been initialized (i.e., mapped via ioremap), this will cause dereferencing a NULL pointer. To fix this, do not access the comm channel in the internal error flow if it has not yet been initialized. Fixes: 55ad359225b2 ("net/mlx4_core: Enable device recovery flow with SRIOV") Fixes: ab9c17a009ee ("mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4: Add VF vlan protocol 802.1ad supportMoshe Shemesh2016-09-241-3/+48
| | | | | | | | | | | | | | | | | | | | | | | | Move the vf to VST 802.1ad mode (mlx4 VST QinQ mode) by setting vf vlan protocol to 802.1ad. VST 802.1ad mode in mlx4, is used for STAG strip/insertion by PF, while the CTAG is set by the VF. Read current vlan protocol as part of the vf configuration state. Upon setting vf vlan protocol to 802.1ad, we use a mechanism of handshake to verify that both the vf and the pf driver version support it. The handshake uses the command QUERY_FUNC_CAP: - The vf sets a pre-defined support bit in input modifier. - A pf that supports the feature sends the request to the vf through a pre-defined field in the output mailbox. - In case vf does not support the feature, the pf will fail the control command (in this case, IP link tool command to set the vf vlan protocol to 802.1ad). No change in VST 802.1Q mode. Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_core: Preparation for VF vlan protocol 802.1adMoshe Shemesh2016-09-241-0/+7
| | | | | | | | | | | | | | | Check device capability to support VF vlan protocol 802.1ad mode. Add vport attribute vlan protocol. Init vport vlan protocol by default to 802.1Q. Add update QP support for VF vlan protocol 802.1ad. Add func capability vlan_offload_disable to disable all vlan HW acceleration on VF while the VF is set to VF vlan protocol 802.1ad mode. No change in VF vlan protocol 802.1Q (VST) mode. Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_core: Fix deadlock when switching between polling and event fw commandsJack Morgenstein2016-09-221-6/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | When switching from polling-based fw commands to event-based fw commands, there is a race condition which could cause a fw command in another task to hang: that task will keep waiting for the polling sempahore, but may never be able to acquire it. This is due to mlx4_cmd_use_events, which "down"s the sempahore back to 0. During driver initialization, this is not a problem, since no other tasks which invoke FW commands are active. However, there is a problem if the driver switches to polling mode and then back to event mode during normal operation. The "test_interrupts" feature does exactly that. Running "ethtool -t <eth device> offline" causes the PF driver to temporarily switch to polling mode, and then back to event mode. (Note that for VF drivers, such switching is not performed). Fix this by adding a read-write semaphore for protection when switching between modes. Fixes: 225c7b1feef1 ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_en: initialize cmd.context_lock spinlock earlierEric Dumazet2016-06-151-1/+0Star
| | | | | | | | | | | | | | | | | | | | | | | | Maciej Żenczykowski reported lockdep warning a spinlock was not registered before being held in mlx4_cmd_wake_completions() cmd.context_lock initialization is not at the right place. 1) mlx4_cmd_use_events() can be called multiple times. Calling spin_lock_init() on a live spinlock can lead to hangs. 2) mlx4_cmd_wake_completions() can be called while lock has not been initialized. Lockdep complains, and current logic is not race prone. It seems better to move the initialization earlier in mlx4_load_one() Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Maciej Żenczykowski <maze@google.com> Cc: Eugenia Emantayev <eugenia@mellanox.com> Cc: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4: fix some error handling in mlx4_multi_func_init()Rasmus Villemoes2016-02-111-1/+1
| | | | | | | | | | | | | | | The while loop after err_slaves should use post-decrement; otherwise we'll fail to do the kfrees for i==0, and will run into out-of-bounds accesses if the setup above failed already at i==0. [I'm not sure why one even bothers populating the ->vlan_filter array: mlx4.h isn't #included by anything outside drivers/net/ethernet/mellanox/mlx4/, and "git grep -C2 -w vlan_filter drivers/net/ethernet/mellanox/mlx4/" seems to suggest that the vlan_filter elements aren't used at all.] Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Doug Ledford <dledford@redhat.com>
* IB/mlx4: Use correct order of variables in log messageWengang Wang2015-12-081-1/+1
| | | | | | | | There is a mis-order in mlx4 log. Fix it. Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com> Acked-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
* net/mlx4: Copy/set only sizeof struct mlx4_eqe bytesCarol L Soto2015-10-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | When doing memcpy/memset of EQEs, we should use sizeof struct mlx4_eqe as the base size and not caps.eqe_size which could be bigger. If caps.eqe_size is bigger than the struct mlx4_eqe then we corrupt data in the master context. When using a 64 byte stride, the memcpy copied over 63 bytes to the slave_eq structure. This resulted in copying over the entire eqe of interest, including its ownership bit -- and also 31 bytes of garbage into the next WQE in the slave EQ -- which did NOT include the ownership bit (and therefore had no impact). However, once the stride is increased to 128, we are overwriting the ownership bits of *three* eqes in the slave_eq struct. This results in an incorrect ownership bit for those eqes, which causes the eq to seem to be full. The issue therefore surfaced only once 128-byte EQEs started being used in SRIOV and (overarchitectures that have 128/256 byte cache-lines such as PPC) - e.g after commit 77507aa249ae "net/mlx4_core: Enable CQE/EQE stride support". Fixes: 08ff32352d6f ('mlx4: 64-byte CQE/EQE support') Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_core: Relieve cpu load average on the port sending flowJack Morgenstein2015-07-271-2/+15
| | | | | | | | | | | | | | | | | | | | | | When a port is not attached, the FW requires a longer than usual time to execute the SENSE_PORT command. In the command flow, the wait_for_completion_timeout call used in mlx4_cmd_wait puts the kernel thread into the uninterruptible state during this time. This, in turn, due to the computation method, causes the CPU load average to increase. Fix this by using wait_for_completion_interruptible_timeout() for the SENSE_PORT command, which puts the thread in the interruptible state. In this state, the thread does not contribute to the CPU load average. Treat the interrupted case as if the SENSE_PORT command returned port_type = NONE. Fix suggested by Gideon Naim <gideonn@mellanox.com> and Bart Van Assche <bart.vanassche@sandisk.com>. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_en: Support ndo_get_vf_statsEran Ben Elisha2015-06-161-0/+30
| | | | | | | | | | | | Implement the ndo to gather VF statistics through the PF. All counters related to this VF are stored in a per slave list, run over the slave's list and collect all statistics. Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_core: Add helper to query countersEran Ben Elisha2015-06-161-0/+57
| | | | | | | | | | | | This is an infrastructure step for querying VF and PF counters. This code was in the IB driver, move it to the mlx4 core driver so it will be accessible for more use cases. Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_core: fix typo in mlx4_set_vf_macCarol Soto2015-06-041-1/+1
| | | | | | | | fix typo in mlx4_set_vf_mac Acked-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2015-06-021-2/+7
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/net/phy/amd-xgbe-phy.c drivers/net/wireless/iwlwifi/Kconfig include/net/mac80211.h iwlwifi/Kconfig and mac80211.h were both trivial overlapping changes. The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and the bug fix that happened on the 'net' side is already integrated into the rest of the amd-xgbe driver. Signed-off-by: David S. Miller <davem@davemloft.net>
| * mlx4_core: Fix fallback from MSI-X to INTxBenjamin Poirier2015-05-271-2/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | The test in mlx4_load_one() to remove MLX4_FLAG_MSI_X expects mlx4_NOP() to fail with -EBUSY. It is also necessary to avoid the reset since the device is not fully reinitialized before calling mlx4_start_hca() a second time. Note that this will also affect mlx4_test_interrupts(), the only other user of MLX4_CMD_NOP. Fixes: f5aef5a ("net/mlx4_core: Activate reset flow upon fatal command cases") Signed-off-by: Benjamin Poirier <bpoirier@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net/mlx4_core: Enable single ported IB VFsOr Gerlitz2015-05-251-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | Remove the limitation that disallows configuring single ported VFs in the presence of IB ports, after addressing the issues that prevented that to work. SMI (QP0) requests/responses are still not supported for single ported IB VFs. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net/mlx4_core: Enhance the MAD_IFC wrapper to convert VF port to physicalOr Gerlitz2015-05-251-4/+6
|/ | | | | | | | | | | | | | | Single port VFs always provide port = 1 (even if the actual physical port used is port 2). As such, we need to convert the port provided by the VF to the physical port before calling into the firmware. It turns out that the Linux mlx4 VF RoCE driver maintains a copy of the GID table and hence this change became critical only for single ported IB VFs, but it could be needed for other RoCE VF drivers too. Fixes: 449fc48866f7 ('net/mlx4: Adapt code for N-Port VF') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_core: Return the admin alias GUID upon host view requestYishai Hadas2015-04-151-14/+27
| | | | | | | | | | | | | | Return the admin alias GUID value upon a GET request via HOST. We do this so that the GUID value requested by the admin is returned even if the SM has not yet approved this GUID (e.g. the SM is down). Note that this does not create a problem, since the virtual port will remain down until the SM does ACK the requested GUID value. Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
* net/mlx4_core: Set initial admin GUIDs for VFsYishai Hadas2015-04-151-0/+1
| | | | | | | | | | To have out of the box experience, the PF generates random GUIDs who serve as the initial admin values. Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2015-04-071-1/+2
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/net/ethernet/mellanox/mlx4/cmd.c net/core/fib_rules.c net/ipv4/fib_frontend.c The fib_rules.c and fib_frontend.c conflicts were locking adjustments in 'net' overlapping addition and removal of code in 'net-next'. The mlx4 conflict was a bug fix in 'net' happening in the same place a constant was being replaced with a more suitable macro. Signed-off-by: David S. Miller <davem@davemloft.net>
| * net/mlx4_core: Fix error message deprecation for ConnectX-2 cardsJack Morgenstein2015-04-061-1/+2
| | | | | | | | | | | | | | | | | | | | | | Commit 1daa4303b4ca ("net/mlx4_core: Deprecate error message at ConnectX-2 cards startup to debug") did the deprecation only for port 1 of the card. Need to deprecate for port 2 as well. Fixes: 1daa4303b4ca ("net/mlx4_core: Deprecate error message at ConnectX-2 cards startup to debug") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net/mlx4: Add SET_PORT opcode modifiers enumerationIdo Shamay2015-04-021-1/+2
| | | | | | | | | | | | | | | | | | The calls to SET_PORT used hard-code numbers, when supplying command's opcode modifiers, fix that to use well defined constants. Signed-off-by: Ido Shamay <idos@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net/mlx4_en: Enable TX rate limit per VFIdo Shamay2015-04-021-1/+176
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Support granular QoS per VF, by implementing the ndo_set_vf_rate. Enforce a rate limit per VF when called, and enabled only for VFs in VST mode with user priority supported by the device. We don't enforce VFs to be in VST mode at the moment of configuration, but rather save the given rate limit and enforce it when the VF is moved to VST with user priority which is supported (currently 0). VST<->VGT or VST qos value state changes are disallowed when a rate limit is configured. Minimum BW share is not supported yet. Signed-off-by: Ido Shamay <idos@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net/mlx4: Added qos_vport QP configuration in VST modeIdo Shamay2015-04-021-1/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | Granular QoS per VF feature introduce a new QP field, qos_vport. PF administrator can connect VF QPs to a certain QoS Vport, to inherit its proporties. Connecting QPs to the default QoS Vport (defined as 0) is always allowed, even when there are no allocated VPPs. At this point, only the default vport is connected to QPs. Signed-off-by: Ido Shamay <idos@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net/mlx4: Allocate VPPs for each port on PF initIdo Shamay2015-04-021-0/+66
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Initialization of granular Qos per VF mechanism. Query the port availible VPPs and allocates those on all supported priorities in an equal share. Allocation is done only in SRIOV mode, when the feature is supported by the device and port type is Ethernet. Allocation currently is done only on the default priority 0. Signed-off-by: Ido Shamay <idos@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net/mlx4: Add mlx4_SET_VPORT_QOS implementationIdo Shamay2015-04-021-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | Add the SET_VPORT_QOS device command, which is ntended for virtual granular QoS configuration per VF in SRIOV mode. The SET_VPORT_QOS command sets and queries QoS parameters of a VPort. Each priority allowed for a VPort is assigned with a share of the BW, and a BW limitation. QoS parameters can be modified at any time, but must be initialized before any QP is associated with the VPort. Signed-off-by: Ido Shamay <idos@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net/mlx4: Add mlx4_ALLOCATE_VPP implementationIdo Shamay2015-04-021-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Implements device ALLOCATE_VPP command, to be used for granular QoS configuration of VFs by the PF device. Defines and queries the amount of VPPs assigned to each port, and the amount of VPPs assigned to each priority of each port. Once the total VPPs are split between the priorities of a port, they may be assigned with a share of the BW or a rate limit. Split into two functions (get/set) whoch are supplied with mlx4_alloc_vpp_context and physical port number. Signed-off-by: Ido Shamay <idos@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net/mlx4: Aesthetic code changes in multi_func_initIdo Shamay2015-04-021-4/+15
| | | | | | | | | | | | | | | | | | | | Previous vf_oper and vf_admin code created very long lines, making it hard to read the code. Added relevant in-struct pointers to reduce code complexity and avoid code lines spread over 80 lines. Same logic is preserved. Signed-off-by: Ido Shamay <idos@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2015-04-021-1/+1
|\| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/net/usb/asix_common.c drivers/net/usb/sr9800.c drivers/net/usb/usbnet.c include/linux/usb/usbnet.h net/ipv4/tcp_ipv4.c net/ipv6/tcp_ipv6.c The TCP conflicts were overlapping changes. In 'net' we added a READ_ONCE() to the socket cached RX route read, whilst in 'net-next' Eric Dumazet touched the surrounding code dealing with how mini sockets are handled. With USB, it's a case of the same bug fix first going into net-next and then I cherry picked it back into net. Signed-off-by: David S. Miller <davem@davemloft.net>
| * net/mlx4_core: Fix GEN_EQE accessing uninitialixed mutexJack Morgenstein2015-03-241-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We occasionally see in procedure mlx4_GEN_EQE that the driver tries to grab an uninitialized mutex. This can occur in only one of two ways: 1. We are trying to generate an async event on an uninitialized slave. 2. We are trying to generate an async event on an illegal slave number ( < 0 or > persist->num_vfs) or an inactive slave. To deal with #1: move the mutex initialization from specific slave init sequence in procedure mlx_master_do_cmd to mlx4_multi_func_init() (so that the mutex is always initialized for all slaves). To deal with #2: check in procedure mlx4_GEN_EQE that the slave number provided is in the proper range and that the slave is active. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net/mlx4_core: Add basic elements for QCNShani Michaeli2015-03-071-0/+9
|/ | | | | | | | | | | | Add device capability, firmware command opcode and etc prior elements needed for QCN suppprt. Disable SRIOV VF view/access for QCN is disabled. While here, remove a redundant offset definition into the QUERY_DEV_CAP mailbox. Signed-off-by: Shani Michaeli <shanim@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_core: Port aggregation low level interfaceMoni Shoua2015-02-051-0/+9
| | | | | | | | | | | | | | Implement the hardware interface required for port aggregation. 1. Disable RX port check on receive - don't perform a validity check that matches to QP's port and the port where the packet is received. 2. Virtual to physical port remap - configure virtual to physical port mapping. Port remap capability for virtual functions. Signed-off-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4: Fix memory corruption in mlx4_MAD_IFC_wrapperMatan Barak2015-01-281-1/+3
| | | | | | | | | | | | | | | Fix a memory corruption at mlx4_MAD_IFC_wrapper. A table of size dev->caps.pkey_table_len[port]*sizeof(*table) was allocated, but get_full_pkey_table() assumes that the number of entries in the table is a multiplication of 32 (which isn't always correct). Fixes: 0a9a018 ('mlx4: MAD_IFC paravirtualization') Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_core: Fix HW2SW_EQ to conform to the firmware specJack Morgenstein2015-01-281-1/+1
| | | | | | | | | | The driver incorrectly assigned an out-mailbox to this command, and used an opcode modifier = 0, which is a reserved value (it should use opcode modifier = 1). Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_core: Reset flow activation upon SRIOV fatal command casesYishai Hadas2015-01-251-33/+92
| | | | | | | | | | | | | | When SRIOV commands are executed over the comm-channel and get a fatal error (e.g. timeout, closing command failure) the VF enters into error state and reset flow is activated. To be able to recognize whether the failure was on a closing command, the operational code for the given VHCR command is used. Once the device entered into an error state we prevent redundant error messages from being printed. Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_core: Enable device recovery flow with SRIOVYishai Hadas2015-01-251-19/+58
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In SRIOV, both the PF and the VF may attempt device recovery whenever they assume that the device is not functioning. When the PF driver resets the device, the VF should detect this and attempt to reinitialize itself. The VF must be able to reset itself under all circumstances, even if the PF is not responsive. The VF shall reset itself in the following cases: 1. Commands are not processed within reasonable time over the communication channel. This is done considering device state and the correct return code based on the command as was done in the native mode, done in the next patch. 2. The VF driver receives an internal error event reported by the PF on the communication channel. This occurs when the PF driver resets the device or when VF is out of sync with the PF. Add 'VF reset' capability, which allows the VF to reinitialize itself even when the PF is not responsive. As PF and VF may run their reset flow simulantanisly, there are several cases that are handled: - Prevent freeing VF resources upon FLR, when PF is in its unloading stage. - Prevent PF getting VF commands before it has finished initializing its resources. - Upon VF startup, check that comm-channel is online before sending commands to the PF and getting timed-out. Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_core: Activate reset flow upon fatal command casesYishai Hadas2015-01-251-21/+142
| | | | | | | | | | | | | | | | | | | | | | | | | | We activate reset flow upon command fatal errors, when the device enters an erroneous state, and must be reset. The cases below are assumed to be fatal: FW command timed-out, an error from FW on closing commands, pci is offline when posting/pending a command. In those cases we place the device into an error state: chip is reset, pending commands are awakened and completed immediately. Subsequent commands will return immediately. The return code in the above cases will depend on the command. Commands which free and close resources will return success (because the chip was reset, so callers may safely free their kernel resources). Other commands will return -EIO. Since the device's state was marked as error, the catas poller will detect this and restart the device's software stack (as is done when a FW internal error is directly detected). The device state is protected by a persistent mutex lives on its mlx4_dev, as such no need any more for the hcr_mutex which is removed. Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_core: Maintain a persistent memory for mlx4 deviceYishai Hadas2015-01-251-21/+25
| | | | | | | | | Maintain a persistent memory that should survive reset flow/PCI error. This comes as a preparation for coming series to support above flows. Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_core: Refactor mlx4_cmd_init and mlx4_cmd_cleanupMatan Barak2014-11-131-32/+44
| | | | | | | | | | | | | Refactoring mlx4_cmd_init and mlx4_cmd_cleanup such that partial init and cleanup are possible. After this refactoring, calling mlx4_cmd_init several times is safe. This is necessary in the VF init flow when mlx4_init_hca returns -EACCESS, we need to issue cleanup and re-attempt to call it with the slave flag. Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_core: Add retrieval of CONFIG_DEV parametersMatan Barak2014-11-031-2/+2
| | | | | | | | | | | | | | Add code to issue CONFIG_DEV "get" firmware command. This command is used in order to obtain certain parameters used for supporting various RX checksumming options and vxlan UDP port. The GET operation is allowed for VFs too. Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Shani Michaeli <shanim@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_core: Prevent VF from changing port configurationSaeed Mahameed2014-11-031-1/+1
| | | | | | | | | | | | | Added wrapper to the ACCESS_REG command for handling guest HW registers access, preventing write operations, but do allow reads. This will prevent SRIOV guests to change port PTYS configuration, such as speed/advertised link modes. Fixes: adbc7ac5c15e ('net/mlx4_core: Introduce ACCESS_REG CMD [...]') Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx4_core: Introduce ACCESS_REG CMD and eth_prot_ctrl dev capSaeed Mahameed2014-10-281-0/+9
| | | | | | | | | | Adding ACCESS REG mlx4 command and use it to implement Query method for PTYS (Port Type and Speed Register). Query and store eth_prot_ctrl dev cap. Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds2014-10-091-2/+12
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull networking updates from David Miller: "Most notable changes in here: 1) By far the biggest accomplishment, thanks to a large range of contributors, is the addition of multi-send for transmit. This is the result of discussions back in Chicago, and the hard work of several individuals. Now, when the ->ndo_start_xmit() method of a driver sees skb->xmit_more as true, it can choose to defer the doorbell telling the driver to start processing the new TX queue entires. skb->xmit_more means that the generic networking is guaranteed to call the driver immediately with another SKB to send. There is logic added to the qdisc layer to dequeue multiple packets at a time, and the handling mis-predicted offloads in software is now done with no locks held. Finally, pktgen is extended to have a "burst" parameter that can be used to test a multi-send implementation. Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4, virtio_net Adding support is almost trivial, so export more drivers to support this optimization soon. I want to thank, in no particular or implied order, Jesper Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann, David Tat, Hannes Frederic Sowa, and Rusty Russell. 2) PTP and timestamping support in bnx2x, from Michal Kalderon. 3) Allow adjusting the rx_copybreak threshold for a driver via ethtool, and add rx_copybreak support to enic driver. From Govindarajulu Varadarajan. 4) Significant enhancements to the generic PHY layer and the bcm7xxx driver in particular (EEE support, auto power down, etc.) from Florian Fainelli. 5) Allow raw buffers to be used for flow dissection, allowing drivers to determine the optimal "linear pull" size for devices that DMA into pools of pages. The objective is to get exactly the necessary amount of headers into the linear SKB area pre-pulled, but no more. The new interface drivers use is eth_get_headlen(). From WANG Cong, with driver conversions (several had their own by-hand duplicated implementations) by Alexander Duyck and Eric Dumazet. 6) Support checksumming more smoothly and efficiently for encapsulations, and add "foo over UDP" facility. From Tom Herbert. 7) Add Broadcom SF2 switch driver to DSA layer, from Florian Fainelli. 8) eBPF now can load programs via a system call and has an extensive testsuite. Alexei Starovoitov and Daniel Borkmann. 9) Major overhaul of the packet scheduler to use RCU in several major areas such as the classifiers and rate estimators. From John Fastabend. 10) Add driver for Intel FM10000 Ethernet Switch, from Alexander Duyck. 11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric Dumazet. 12) Add Datacenter TCP congestion control algorithm support, From Florian Westphal. 13) Reorganize sk_buff so that __copy_skb_header() is significantly faster. From Eric Dumazet" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits) netlabel: directly return netlbl_unlabel_genl_init() net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers net: description of dma_cookie cause make xmldocs warning cxgb4: clean up a type issue cxgb4: potential shift wrapping bug i40e: skb->xmit_more support net: fs_enet: Add NAPI TX net: fs_enet: Remove non NAPI RX r8169:add support for RTL8168EP net_sched: copy exts->type in tcf_exts_change() wimax: convert printk to pr_foo() af_unix: remove 0 assignment on static ipv6: Do not warn for informational ICMP messages, regardless of type. Update Intel Ethernet Driver maintainers list bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING tipc: fix bug in multicast congestion handling net: better IFF_XMIT_DST_RELEASE support net/mlx4_en: remove NETDEV_TX_BUSY 3c59x: fix bad split of cpu_to_le32(pci_map_single()) net: bcmgenet: fix Tx ring priority programming ...
| * net/mlx4_core: Deprecate error message at ConnectX-2 cards startup to debugJack Morgenstein2014-09-301-2/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ConnectX2 HCAs have max_mtu=4k and max_vl=8 vls. However, if you specify a 4K mtu, the max_vl supported for 4K is 4 vls. The driver at startup attempts to set a 4K mtu using the max_vl value obtained from QUERY_PORT. Since the max_vl value is 8 vls (which is supported up to 2K mtu size), the first attempt to set the mtl/vl port value will fail, generating the following error message in the log: mlx4_core 0000:06:00.0: command 0xc failed: fw status = 0x40 The driver then tries again, using mtu=4k, vls=4, and this succeeds. Since we do not want to have this error message always displayed at driver start when there are ConnectX2 HCAs on the host, we deprecate the error message for this specific command/input_modifier/opcode_modifier/fw-status to be debug. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge branch 'for-linus' of ↵Linus Torvalds2014-10-081-2/+2
|\ \ | |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial Pull "trivial tree" updates from Jiri Kosina: "Usual pile from trivial tree everyone is so eagerly waiting for" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits) Remove MN10300_PROC_MN2WS0038 mei: fix comments treewide: Fix typos in Kconfig kprobes: update jprobe_example.c for do_fork() change Documentation: change "&" to "and" in Documentation/applying-patches.txt Documentation: remove obsolete pcmcia-cs from Changes Documentation: update links in Changes Documentation: Docbook: Fix generated DocBook/kernel-api.xml score: Remove GENERIC_HAS_IOMAP gpio: fix 'CONFIG_GPIO_IRQCHIP' comments tty: doc: Fix grammar in serial/tty dma-debug: modify check_for_stack output treewide: fix errors in printk genirq: fix reference in devm_request_threaded_irq comment treewide: fix synchronize_rcu() in comments checkstack.pl: port to AArch64 doc: queue-sysfs: minor fixes init/do_mounts: better syntax description MIPS: fix comment spelling powerpc/simpleboot: fix comment ...
| * treewide: fix errors in printkMasanari Iida2014-09-011-2/+2
| | | | | | | | | | | | | | | | | | This patch fix spelling typo in printk. Signed-off-by: Masanari Iida <standby24x7@gmail.com> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* | net/mlx4: Correctly configure single ported VFs from the hostMatan Barak2014-09-111-0/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Single port VFs are seen PCI wise on both ports of the PF (we don't have single port PFs with ConnectX). With this in mind, it's possible for virtualization tools to try and configure a single ported VF through the "wrong" PF port. To handle that, we use the PF driver mapping of single port VFs to NIC ports and adjust the port value before calling into the low level code that does the actual VF configuration Fixes: 449fc48 ('net/mlx4: Adapt code for N-Port VF') Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | mlx4_core: Add support for secure-host and SMP firewallJack Morgenstein2014-08-051-0/+9
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Secure-host is the general term for the capability of a device to protect itself and the subnet from malicious host software. This is achieved by: 1. Not allowing un-trusted entities to access device configuration registers, directly (through pci_cr or pci_conf) and indirectly (through MADs). 2. Hiding M_Key from untrusted entities. 3. Preventing the modification of GUID0 by un-trusted entities 4. Not allowing drivers on untrusted hosts to receive nor to transmit packets over QP0 (SMP Firewall). The secure-host capability depends on firmware handling all QP0 packets, and not passing these packets up to the driver. Any information required by the driver for proper operation (e.g., SM lid) is passed via events generated by the firmware while processing QP0 MADs. Driver support mainly requires using the MAD_DEMUX FW command at startup, where the feature is enabled/disabled through a procedure described in the Mellanox HCA tools package. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> [ Fix error path in mlx4_setup_hca to go to err_mcg_table_free. - Roland ] Signed-off-by: Roland Dreier <roland@purestorage.com>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds2014-06-121-51/+58
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull networking updates from David Miller: 1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov. 2) Multiqueue support in xen-netback and xen-netfront, from Andrew J Benniston. 3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn Mork. 4) BPF now has a "random" opcode, from Chema Gonzalez. 5) Add more BPF documentation and improve test framework, from Daniel Borkmann. 6) Support TCP fastopen over ipv6, from Daniel Lee. 7) Add software TSO helper functions and use them to support software TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia. 8) Support software TSO in fec driver too, from Nimrod Andy. 9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli. 10) Handle broadcasts more gracefully over macvlan when there are large numbers of interfaces configured, from Herbert Xu. 11) Allow more control over fwmark used for non-socket based responses, from Lorenzo Colitti. 12) Do TCP congestion window limiting based upon measurements, from Neal Cardwell. 13) Support busy polling in SCTP, from Neal Horman. 14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru. 15) Bridge promisc mode handling improvements from Vlad Yasevich. 16) Don't use inetpeer entries to implement ID generation any more, it performs poorly, from Eric Dumazet. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits) rtnetlink: fix userspace API breakage for iproute2 < v3.9.0 tcp: fixing TLP's FIN recovery net: fec: Add software TSO support net: fec: Add Scatter/gather support net: fec: Increase buffer descriptor entry number net: fec: Factorize feature setting net: fec: Enable IP header hardware checksum net: fec: Factorize the .xmit transmit function bridge: fix compile error when compiling without IPv6 support bridge: fix smatch warning / potential null pointer dereference via-rhine: fix full-duplex with autoneg disable bnx2x: Enlarge the dorq threshold for VFs bnx2x: Check for UNDI in uncommon branch bnx2x: Fix 1G-baseT link bnx2x: Fix link for KR with swapped polarity lane sctp: Fix sk_ack_backlog wrap-around problem net/core: Add VF link state control policy net/fsl: xgmac_mdio is dependent on OF_MDIO net/fsl: Make xgmac_mdio read error message useful net_sched: drr: warn when qdisc is not work conserving ...
| * Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2014-05-241-2/+2
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/net/bonding/bond_alb.c drivers/net/ethernet/altera/altera_msgdma.c drivers/net/ethernet/altera/altera_sgdma.c net/ipv6/xfrm6_output.c Several cases of overlapping changes. The xfrm6_output.c has a bug fix which overlaps the renaming of skb->local_df to skb->ignore_df. In the Altera TSE driver cases, the register access cleanups in net-next overlapped with bug fixes done in net. Similarly a bug fix to send ALB packets in the bonding driver using the right source address overlaps with cleanups in net-next. Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3-55-g7522 (git 2.39.0) at 2024-07-22 22:40:20 +0200