| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Speed translation is performed based on legacy or extended PTYS
register. Translate speed with respect to:
1) Capability bit of extended PTYS table.
2) User request:
a) When auto-negotiation is turned on, inspect advertisement whether it
contains extended link modes.
b) When auto-negotiation is turned off, speed > 100Gbps (maximal
speed supported in legacy mode).
With both conditions fulfilled translation is done with extended PTYS
table otherwise use legacy PTYS table.
Without this patch 25/50/100 Gbps speed cannot be set, since try to
configure in extended mode but read from legacy mode.
Fixes: dd1b9e09c12b ("net/mlx5: ethtool, Allow legacy link-modes configuration via non-extended ptys")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch exposes new link modes (including 50Gbps per lane), and ext_*
fields which describes the new link modes in Port Type and Speed
register (PTYS).
Access functions, translation functions (speed <-> HW bits) and
link max speed function were modified.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch fascicles queries to speed related fields in Port Type and
Speed register (PTYS) into a single API. I addition, this patch
refactors functions which serves only Ethernet driver: remove the
protocol type as an input parameter, move code from 'core' directory
into 'en' directory and add 'eth' prefix to the function's name. The
patch also encapsulates functions that are not used outside the Ethernet
driver removes redundant include files.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Added functions to query and set link FEC policy.
To get/set FEC capabilities in PPLM reg we need to query
current link speed.
'mlx5_get_fec_speed_field' queries current link speed and returns
correct field offset.
FEC Query's return value is divided into 'active FEC policy', which is
the FEC policy used by the link, and 'configured FEC policy', which
is the FEC policy requested by the user.
The two values may differ if:
1) FEC policy was configured to 'auto',
in which case the active FEC policy would be the default FEC policy
for current link speed.
2) FEC policy was changed, but no link reset is performed. In which case,
the active FEC policy would become the configured one after a link
reset.
FEC set function sets FEC policy for all link speeds and perform link
reset.
1) If current link speed doesn't support requested FEC policy,
the function fails.
2) If a different link speed doesn't support requested FEC policy,
FEC capbilities for this speed are turned off and a warning message
is printed.
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add firmware command interface to read and write PPTB and PBMC
registers.
PPTB register enables mappings priority to a specific receive buffer.
PBMC registers enables changing the receive buffer's configuration such
as buffer size, xon/xoff thresholds, buffer's lossy property and
buffer's shared property.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Move four below functions from en_ethtool.c to en/port.c. These
functions are used by both en_ethtool.c and en_main.c. Future code
can use these functions without ethtool link mode dependency.
u32 mlx5e_port_ptys2speed(u32 eth_proto_oper);
int mlx5e_port_linkspeed(struct mlx5_core_dev *mdev, u32 *speed);
int mlx5e_port_max_linkspeed(struct mlx5_core_dev *mdev, u32 *speed);
u32 mlx5e_port_speed2linkmodes(u32 speed);
Delete the speed field from table mlx5e_build_ptys2ethtool_map. This
table only keeps the mapping between the mlx5e link mode and
ethtool link mode. Add new table mlx5e_link_speed for translation
from mlx5e link mode to actual speed.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|