| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
| |
New operation for getting the port's speed as part of port-type-speed
operations.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Set the PTP shaper parameters during the ptp_init(). For different
speeds, there are different parameters.
When the port's speed changes and PTP shaper is enabled, the firmware
changes the ETS shaper values according to the PTP shaper parameters for
this new speed.
The PTP shaper parameters array is left empty for now, will be filled in
a follow-up patch.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
| |
The QPSC allows advanced configuration of the PTP shapers.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
| |
Add note about disabling the PTP shaper when calling to
mlxsw_sp_port_ets_maxrate_set().
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
| |
The PTP Shaper field is used for enabling and disabling of port-rate based
shaper which is slightly lower than port rate.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-07-03
The following pull-request contains BPF updates for your *net-next* tree.
There is a minor merge conflict in mlx5 due to 8960b38932be ("linux/dim:
Rename externally used net_dim members") which has been pulled into your
tree in the meantime, but resolution seems not that bad ... getting current
bpf-next out now before there's coming more on mlx5. ;) I'm Cc'ing Saeed
just so he's aware of the resolution below:
** First conflict in drivers/net/ethernet/mellanox/mlx5/core/en_main.c:
<<<<<<< HEAD
static int mlx5e_open_cq(struct mlx5e_channel *c,
struct dim_cq_moder moder,
struct mlx5e_cq_param *param,
struct mlx5e_cq *cq)
=======
int mlx5e_open_cq(struct mlx5e_channel *c, struct net_dim_cq_moder moder,
struct mlx5e_cq_param *param, struct mlx5e_cq *cq)
>>>>>>> e5a3e259ef239f443951d401db10db7d426c9497
Resolution is to take the second chunk and rename net_dim_cq_moder into
dim_cq_moder. Also the signature for mlx5e_open_cq() in ...
drivers/net/ethernet/mellanox/mlx5/core/en.h +977
... and in mlx5e_open_xsk() ...
drivers/net/ethernet/mellanox/mlx5/core/en/xsk/setup.c +64
... needs the same rename from net_dim_cq_moder into dim_cq_moder.
** Second conflict in drivers/net/ethernet/mellanox/mlx5/core/en_main.c:
<<<<<<< HEAD
int cpu = cpumask_first(mlx5_comp_irq_get_affinity_mask(priv->mdev, ix));
struct dim_cq_moder icocq_moder = {0, 0};
struct net_device *netdev = priv->netdev;
struct mlx5e_channel *c;
unsigned int irq;
=======
struct net_dim_cq_moder icocq_moder = {0, 0};
>>>>>>> e5a3e259ef239f443951d401db10db7d426c9497
Take the second chunk and rename net_dim_cq_moder into dim_cq_moder
as well.
Let me know if you run into any issues. Anyway, the main changes are:
1) Long-awaited AF_XDP support for mlx5e driver, from Maxim.
2) Addition of two new per-cgroup BPF hooks for getsockopt and
setsockopt along with a new sockopt program type which allows more
fine-grained pass/reject settings for containers. Also add a sock_ops
callback that can be selectively enabled on a per-socket basis and is
executed for every RTT to help tracking TCP statistics, both features
from Stanislav.
3) Follow-up fix from loops in precision tracking which was not propagating
precision marks and as a result verifier assumed that some branches were
not taken and therefore wrongly removed as dead code, from Alexei.
4) Fix BPF cgroup release synchronization race which could lead to a
double-free if a leaf's cgroup_bpf object is released and a new BPF
program is attached to the one of ancestor cgroups in parallel, from Roman.
5) Support for bulking XDP_TX on veth devices which improves performance
in some cases by around 9%, from Toshiaki.
6) Allow for lookups into BPF devmap and improve feedback when calling into
bpf_redirect_map() as lookup is now performed right away in the helper
itself, from Toke.
7) Add support for fq's Earliest Departure Time to the Host Bandwidth
Manager (HBM) sample BPF program, from Lawrence.
8) Various cleanups and minor fixes all over the place from many others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This commit adds support for AF_XDP zero-copy RX and TX.
We create a dedicated XSK RQ inside the channel, it means that two
RQs are running simultaneously: one for non-XSK traffic and the other
for XSK traffic. The regular and XSK RQs use a single ID namespace split
into two halves: the lower half is regular RQs, and the upper half is
XSK RQs. When any zero-copy AF_XDP socket is active, changing the number
of channels is not allowed, because it would break to mapping between
XSK RQ IDs and channels.
XSK requires different page allocation and release routines. Such
functions as mlx5e_{alloc,free}_rx_mpwqe and mlx5e_{get,put}_rx_frag are
generic enough to be used for both regular and XSK RQs, and they use the
mlx5e_page_{alloc,release} wrappers around the real allocation
functions. Function pointers are not used to avoid losing the
performance with retpolines. Wherever it's certain that the regular
(non-XSK) page release function should be used, it's called directly.
Only the stats that could be meaningful for XSK are exposed to the
userspace. Those that don't take part in the XSK flow are not
considered.
Note that we don't wait for WQEs on the XSK RQ (unlike the regular RQ),
because the newer xdpsock sample doesn't provide any Fill Ring entries
at the setup stage.
We create a dedicated XSK SQ in the channel. This separation has its
advantages:
1. When the UMEM is closed, the XSK SQ can also be closed and stop
receiving completions. If an existing SQ was used for XSK, it would
continue receiving completions for the packets of the closed socket. If
a new UMEM was opened at that point, it would start getting completions
that don't belong to it.
2. Calculating statistics separately.
When the userspace kicks the TX, the driver triggers a hardware
interrupt by posting a NOP to a dedicated XSK ICO (internal control
operations) SQ, in order to trigger NAPI on the right CPU core. This XSK
ICO SQ is protected by a spinlock, as the userspace application may kick
the TX from any core.
Store the pointers to the UMEMs in the net device private context,
independently from the kernel. This way the driver can distinguish
between the zero-copy and non-zero-copy UMEMs. The kernel function
xdp_get_umem_from_qid does not care about this difference, but the
driver is only interested in zero-copy UMEMs, particularly, on the
cleanup it determines whether to close the XSK RQ and SQ or not by
looking at the presence of the UMEM. Use state_lock to protect the
access to this area of UMEM pointers.
LRO isn't compatible with XDP, but there may be active UMEMs while
XDP is off. If this is the case, don't allow LRO to ensure XDP can
be reenabled at any time.
The validation of XSK parameters typically happens when XSK queues
open. However, when the interface is down or the XDP program isn't
set, it's still possible to have active AF_XDP sockets and even to
open new, but the XSK queues will be closed. To cover these cases,
perform the validation also in these flows:
1. A new UMEM is registered, but the XSK queues aren't going to be
created due to missing XDP program or interface being down.
2. MTU changes while there are UMEMs registered.
Having this early check prevents mlx5e_open_channels from failing
at a later stage, where recovery is impossible and the application
has no chance to handle the error, because it got the successful
return value for an MTU change or XSK open operation.
The performance testing was performed on a machine with the following
configuration:
- 24 cores of Intel Xeon E5-2620 v3 @ 2.40 GHz
- Mellanox ConnectX-5 Ex with 100 Gbit/s link
The results with retpoline disabled, single stream:
txonly: 33.3 Mpps (21.5 Mpps with queue and app pinned to the same CPU)
rxdrop: 12.2 Mpps
l2fwd: 9.4 Mpps
The results with retpoline enabled, single stream:
txonly: 21.3 Mpps (14.1 Mpps with queue and app pinned to the same CPU)
rxdrop: 9.9 Mpps
l2fwd: 6.8 Mpps
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
structs mlx5e_{rq,sq,cq,channel}_param are going to be used in the
upcoming XSK RX and TX patches. Move them to a header file to make
them accessible from other C files.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Create new functions mlx5e_{open,close}_queues to encapsulate opening
and closing RQs and SQs, and call the new functions from
mlx5e_{open,close}_channel. It simplifies the existing functions a bit
and prepares them for the upcoming AF_XDP changes.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Use the existing mlx5e_get_linear_rq_headroom function to calculate the
headroom for mlx5e_xdp_max_mtu. This function takes the XSK headroom
into consideration, which will be used in the following patches.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When an XDP program returns XDP_TX, and the RQ is XSK-enabled, it
requires careful handling, because convert_to_xdp_frame creates a new
page and copies the data there, while our driver expects the xdp_frame
to point to the same memory as the xdp_buff. Handle this case
separately: map the page, and in the end unmap it and call
xdp_return_frame.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Put the XDP SQ that is used for XDP_TX into the channel. It used to be a
part of the RQ, but with introduction of AF_XDP there will be one more
RQ that could share the same XDP SQ. This patch is a preparation for
that change.
Separate XDP_TX statistics per RQ were implemented in one of the previous
patches.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently, struct mlx5e_xdp_info has some issues that have to be cleaned
up before the upcoming AF_XDP support makes things too complicated and
messy. This structure is used both when sending the packet and on
completion. Moreover, the cleanup procedure on completion depends on the
origin of the packet (XDP_REDIRECT, XDP_TX). Adding AF_XDP support will
add new flows that use this structure even differently. To avoid
overcomplicating the code, this commit refactors the usage of this
structure in the following ways:
1. struct mlx5e_xdp_info is split into two different structures. One is
struct mlx5e_xdp_xmit_data, a transient structure that doesn't need to
be stored and is only used while sending the packet. The other is still
struct mlx5e_xdp_info that is stored in a FIFO and contains the fields
needed on completion.
2. The fields of struct mlx5e_xdp_info that are used in different flows
are put into a union. A special enum indicates the cleanup mode and
helps choose the right union member. This approach is clear and
explicit. Although it could be possible to "guess" the mode by looking
at the values of the fields and at the XDP SQ type, it wouldn't be that
clear and extendable and would require looking through the whole chain
to understand what's going on.
For the reference, there are the fields of struct mlx5e_xdp_info that
are used in different flows (including AF_XDP ones):
Packet origin | Fields used on completion | Cleanup steps
-----------------------+---------------------------+------------------
XDP_REDIRECT, | xdpf, dma_addr | DMA unmap and
XDP_TX from XSK RQ | | xdp_return_frame.
-----------------------+---------------------------+------------------
XDP_TX from regular RQ | di | Recycle page.
-----------------------+---------------------------+------------------
AF_XDP TX | (none) | Increment the
| | producer index in
| | Completion Ring.
On send, the same set of mlx5e_xdp_xmit_data fields is used in all
flows: DMA and virtual addresses and length.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Prepare to creation of the XSK RQ, which will require posting UMRs, too.
The same ICO SQ will be used for both RQs and also to trigger interrupts
by posting NOPs. UMR WQEs can't be reused any more. Optimization
introduced in commit ab966d7e4ff98 ("net/mlx5e: RX, Recycle buffer of
UMR WQEs") is reverted.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Additional conditions introduced:
- XSK implies XDP.
- Headroom includes the XSK headroom if it exists.
- No space is reserved for struct shared_skb_info in XSK mode.
- Fragment size smaller than the XSK chunk size is not allowed.
A new auxiliary function mlx5e_get_linear_rq_headroom with the support
for XSK is introduced. Use this function in the implementation of
mlx5e_get_rq_headroom. Change headroom to u32 to match the headroom
field in struct xdp_umem.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The PCI API for DMA is deprecated, and PCI_DMA_TODEVICE is just defined
to DMA_TO_DEVICE for backward compatibility. Just use DMA_TO_DEVICE.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When an XDP program is set, a full reopen of all channels happens in two
cases:
1. When there was no program set, and a new one is being set.
2. When there was a program set, but it's being unset.
The full reopen is necessary, because the channel parameters may change
if XDP is enabled or disabled. However, it's performed in an unsafe way:
if the new channels fail to open, the old ones are already closed, and
the interface goes down. Use the safe way to switch channels instead.
The same way is already used for other configuration changes.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Before mlxsw_sp1_ptp_packet_finish() sends the packet back, it validates
whether the corresponding port is still valid. However the condition is
incorrect: when mlxsw_sp_port == NULL, the code dereferences the port to
compare it to skb->dev.
The condition needs to check whether the port is present and skb->dev still
refers to that port (or else is NULL). If that does not hold, bail out.
Add a pair of parentheses to fix the condition.
Fixes: d92e4e6e33c8 ("mlxsw: spectrum: PTP: Support timestamping on Spectrum-1")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The get_ts_info callback is used for obtaining information about
timestamping capabilities of a network device. On Spectrum-1, implement
it to advertise the PHC and the capability to do HW timestamping, and
the supported RX and TX filters.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The SIOCSHWTSTAMP ioctl configures HW timestamping on a given port.
Dispatch the ioctls to per-chip handler (which add to ptp_ops). Find
which PTP messages need to be timestamped and configure MTPPPC
accordingly.
The SIOCGHWTSTAMP ioctl is getter for the current configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Configure MTPTPT to set which message types should arrive under which
PTP trap, and MOGCR to clear the timestamp queue after its contents are
reported through PTP_ING_FIFO or PTP_EGR_FIFO.
With this configuration, PTP packets start arriving through the PTP
traps. However since timestamping is disabled by default and there is
currently no way to enable it, they will not be timestamped.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
On Spectrum-1, timestamped PTP packets and the corresponding timestamps
need to be kept in caches until both are available, at which point they are
matched up and packets forwarded as appropriate. However, not all packets
will ever see their timestamp, and not all timestamps will ever see their
packet. It is therefore necessary to dispose of such abandoned entries.
To that end, introduce a garbage collector to collect entries that have
not had their counterpart turn up within about a second. The GC
maintains a monotonously-increasing value of GC cycle. Every entry that
is put to the hash table is annotated with the GC cycle at which it
should be collected. When the GC runs, it walks the hash table, and
collects the objects according to their GC cycle annotation.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
On Spectrum-1, timestamps arrive through a pair of dedicated events:
MLXSW_TRAP_ID_PTP_ING_FIFO and _EGR_FIFO. The payload delivered with
those traps is contents of the timestamp FIFO at a given port in a given
direction. Add a Spectrum-1-specific handler for these two events which
decodes the timestamps and forwards them to the PTP module.
Add a function that parses a packet, dispatching to ptp_classify_raw(),
and decodes PTP message type, domain number, and sequence ID. Add a new
mlxsw dependency on the PTP classifier.
Add helpers that can store and retrieve unmatched timestamps and SKBs to
the hash table added in a preceding patch.
Add the matching code itself: upon arrival of a timestamp or a packet,
look up the corresponding unmatched entry, and match it up. If there is
none, add a new unmatched entry. This logic is the same on ingress as on
egress.
Packets and timestamps that never matched need to be eventually disposed
of. A garbage collector added in a follow-up patch will take care of
that. Since currently all this code is turned off, no crud will
accumulate in the hash table.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Up until now, the PTP hardware clock code was only invoked in the process
context (SYS_clock_adjtime -> do_clock_adjtime -> k_clock::clock_adj ->
pc_clock_adjtime -> posix_clock_operations::clock_adjtime ->
ptp_clock_info::adjtime -> mlxsw_spectrum).
In order to enable HW timestamping, which is tied into trap handling, it
will be necessary to take the clock lock from the PCI queue handler
tasklets as well.
Therefore use the _bh variants when handling the clock lock. Incidentally,
Documentation/ptp/ptp.txt recommends _irqsave variants, but that's
unnecessarily strong for our needs.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add two ptp_ops: init and fini, to initialize and finalize the PTP
subsystem. Call as appropriate from mlxsw_sp_init() and _fini().
Lay the groundwork for Spectrum-1 support. On Spectrum-1, the received
timestamped packets and their corresponding timestamps arrive
independently, and need to be matched up. Introduce the related data types
and add to struct mlxsw_sp_ptp_state the hash table that will keep the
unmatched entries.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
On Spectrum-1, timestamps are delivered separately from the packets, and
need to paired up. Therefore, at some point after mlxsw_sp_port_xmit()
is invoked, it is necessary to involve the chip-specific driver code to
allow it to do the necessary bookkeeping and matching.
On Spectrum-2, timestamps are delivered in CQE. For that reason,
position the point of driver involvement into mlxsw_pci_cqe_sdq_handle()
to make it hopefully easier to extend for Spectrum-2 in the future.
To tell the driver what port the packet was sent on, keep tx_info
in SKB control buffer.
Introduce a new driver core interface mlxsw_core_ptp_transmitted(), a
driver callback ptp_transmitted, and a PTP op transmitted. The callee is
responsible for taking care of releasing the SKB passed to the new
interfaces, and correspondingly have the new stub callbacks just call
dev_kfree_skb_any().
Follow-up patches will introduce the actual content into
mlxsw_sp1_ptp_transmitted() in particular.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The SKB control buffer is useful (and used) for bookkeeping of information
related to that SKB. Add helpers so that the mlxsw driver(s) can safely use
the buffer as well. The structure is currently empty, individual users will
add members to it as necessary.
Note that SKB allocation functions already clear the buffer, so the cleanup
is only necessary when ndo_start_xmit is called.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When configured, the Spectrum hardware can recognize PTP packets and
trap them to the CPU using dedicated traps, PTP0 and PTP1.
One reason to get PTP packets under dedicated traps is to have a
separate policer suitable for the amount of PTP traffic expected when
switch is operated as a boundary clock. For this, add two new trap
groups, MLXSW_REG_HTGT_TRAP_GROUP_SP_PTP0 and _PTP1, and associate the
two PTP traps with these two groups.
In the driver, specifically for Spectrum-1, event PTP packets will need
to be paired up with their timestamps. Those arrive through a different
set of traps, added later in the patch set. To support this future use,
introduce a new PTP op, ptp_receive.
It is possible to configure which PTP messages should be trapped under
which PTP trap. On Spectrum systems, we will use PTP0 for event
packets (which need timestamping), and PTP1 for control packets (which
do not). Thus configure PTP0 trap with a custom callback that defers to
the ptp_receive op.
Additionally, L2 PTP packets are actually trapped through the LLDP trap,
not through any of the PTP traps. So treat the LLDP trap the same way as
the PTP0 trap. Unlike PTP traps, which are currently still disabled,
LLDP trap is active. Correspondingly, have all the implementations of
the ptp_receive op return true, which the handler treats as a signal to
forward the packet immediately.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
On Spectrum-1, timestamps for PTP packets are delivered through queues
of ingress and egress timestamps. There are two event traps
corresponding to activity on each of those queues. This mechanism is
absent on Spectrum-2, and therefore the traps should only be registered
on Spectrum-1.
Carry a chip-specific listener array in mlxsw_sp->listeners and
listeners_count. Register listeners from that array in
mlxsw_sp_traps_init(). Add a new listener array for Spectrum-1 traps and
configure the newly-added mlxsw_sp->listeners with this array.
The listener array is empty for now, the events will be added in a later
patch.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
On Spectrum-1, timestamps for PTP packets are delivered through queues
of ingress and egress timestamps. There are two event traps
corresponding to activity on each of those queues. This mechanism is
absent on Spectrum-2, and therefore the traps should only be registered
on Spectrum-1.
Extract out of mlxsw_sp_traps_init() a generic helper,
mlxsw_sp_traps_register(), and likewise with _unregister(). The new helpers
will later be called with Spectrum-1-specific traps.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This register serves to configure global parameters of certain
monitoring operations. The following patches will use it to configure
that when PTP timestamps are delivered through the PTP FIFO traps, the
FIFO in question is cleared as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The MTPPTR is used for reading the per port PTP timestamp FIFO.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This register is used for configuring under which trap to deliver PTP
packets depending on type of the packet.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This register serves for configuration of which PTP messages should be
timestamped. This is a global configuration, despite the register name.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
After changing the parent_id to be the same for both NICs of same
the hardware device, netdev_port_same_parent_id now returns true for
more cases (all the lower devices in the hierarchy are on the same
hardware device).
If merged eswitch isn't enabled, these cases aren't supported, so disallow
them.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Report system_image_guid as the E-Switch switch_id, this ensures
that when a NIC contains multiple PCI functions and which
has merged eswitch capability, all representors from
multiple PFs publish same switch_id.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Refreshing TIRs is done in order to update the TIRs with the current
state of SQs in the transport domain, so that the TIRs can filter out
undesired self-loopback packets based on the source SQ of the packet.
Representor TIRs will only receive packets that originate from their
associated vport, due to dedicated steering, and therefore will never
receive self-loopback packets, whose source vport will be the vport of
the E-Switch manager, and therefore not the vport associated with the
representor. As such, it is not necessary to refresh the representors'
TIRs, since self-loopback packets can't reach them.
Since representors only exist in switchdev mode, and there is no
scenario in which a representor will exist in the transport domain
alongside a non-representor, it is not necessary to refresh the
transport domain's TIRs upon changing the state of a representor's
queues. Therefore, do not refresh TIRs upon such a change. Achieve
this by adding an update_rx callback to the mlx5e_profile, which
refreshes TIRs for non-representors and does nothing for representors,
and replace instances of mlx5e_refresh_tirs() upon changing the state
of the queues with update_rx().
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Putting an empty 'mlx5_flow_spec' structure on the stack is a bit
wasteful and causes a warning on 32-bit architectures when building
with clang -fsanitize-coverage:
drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads_termtbl.c: In function 'mlx5_eswitch_termtbl_create':
drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads_termtbl.c:90:1: error: the frame size of 1032 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Since the structure is never written to, we can statically allocate
it to avoid the stack usage. To be on the safe side, mark all
subsequent function arguments that we pass it into as 'const'
as well.
Fixes: 10caabdaad5a ("net/mlx5e: Use termination table for VLAN push actions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Consider PCI and non PCI device types while setting device name
in get_drvinfo() callback using existing generic device.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently PF phys_port_name is named as pfNvf-1 as vport number for PF
vport is 65535.
Correct PF's phys_port name as agreed upon name as pfN.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Set supported device features in the netdevice MPLS features mask.
This will enable HW checksumming and TSO for MPLS tagged traffic.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch changes the way the driver advertises its checksum offload
capabilities within the net device features bit mask.
Instead of advertising protocol specific checksumming capabilities
which are limited today to IPv4 and IPv6, we move to reporing
generic HW checksumming capabilities.
This will allow the network stack to let mlx5 device offload checksum
for cases where the IP header is encapsulated within another protocol
and the skb->protocol doesn't indicate one of the IP versions protocol,
specifically in the case of MPLS label encapsulating the IP header and
the skb->protocol indiciates MPLS ethertype rather than IP.
Moving the HW_CSUM reporting is required in the basic net device hw
features mask and also in the extensions (vlan and encpasulation
features) since the extensions are always multiplied by the basic
features set during the packet's traversal through the stack's tx flow.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Remove the limitation preventing adding a vport's MAC address to the
Multi-Physical Function Switch (MPFS) more than once per E-switch, as
there is no difference in the MPFS if an address is being used by an
E-switch more than once.
This allows the E-switch to have multiple vports with the same MAC
address, allowing vports to be classified by VLAN id instead of by MAC
if desired.
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Unify and isolate the error handling flow in mlx5_mpfs_add_mac(),
removing code duplication.
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Misc updates from mlx5-next branch:
1) E-Switch vport metadata support for source vport matching
2) Convert mkey_table to XArray
3) Shared IRQs and to use single IRQ for all async EQs
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
As the ingress ACL rules save vhca id and vport number to packet's
metadata REG_C_0, and the metadata matching for the rules in both fast
path and slow path are all added, enable this feature if supported.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In slow path, packet that not matched by any offloaded rule is
forwarded to eswitch vport manager for further processing.
Add matching on metadata for peer miss rules in FDB, and rules which
forward packet to correct representor in esw manager NIC_RX table.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In order to do matching on metadata in slow path when demuxing traffic
to representors, explicitly enable the feature that allows HW to pass
metadata REG_C_0 from FDB to eswitch manager NIC_RX table.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add esw vport query and modify functions, and exposing them is needed for
enabling or disabling registers passed as metatdata to vport NIC_RX table
in slow path.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
If FW's capabilities and configurations meet the requirement of vport
metadata matching, this feature will be used. As the information
about vport number and vhca_id related to packet is already stored to
its metadata register, which is used as an indicator for perticular
vport, now we can change to match on this metadata for all the
offloading rules in fast path.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|