summaryrefslogtreecommitdiffstats
path: root/drivers/net/phy
Commit message (Collapse)AuthorAgeFilesLines
* net: phy: mdio-gpio: Fix working over slow can_sleep GPIOsMartin Schiller2018-11-181-5/+5
| | | | | | | | | | | | | | Up until commit 7e5fbd1e0700 ("net: mdio-gpio: Convert to use gpiod functions where possible"), the _cansleep variants of the gpio_ API was used. After that commit and the change to gpiod_ API, the _cansleep() was dropped. This then results in WARN_ON() when used with GPIO devices which do sleep. Add back the _cansleep() to avoid this. Fixes: 7e5fbd1e0700 ("net: mdio-gpio: Convert to use gpiod functions where possible") Signed-off-by: Martin Schiller <ms@dev.tdt.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Revert "net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs"David S. Miller2018-11-171-9/+5Star
| | | | | | | | This reverts commit dfa0d55ff6be64e7b6881212a291cb95f8da3b08. Discussion still ongoing, I shouldn't have applied this. Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: mdio-gpio: Fix working over slow can_sleep GPIOsMartin Schiller2018-11-171-5/+9
| | | | | | | | | | | | This commit re-enables support for slow GPIO pins. It was initially introduced by commit 2d6c9091ab76 ("net: mdio-gpio: support access that may sleep") and got lost by commit 7e5fbd1e0700 ("net: mdio-gpio: Convert to use gpiod functions where possible"). Also add a warning about slow GPIO pins like it is done in i2c-gpio. Signed-off-by: Martin Schiller <ms@dev.tdt.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: Allow BCM54616S PHY to setup internal TX/RX clock delayTao Ren2018-11-061-2/+16
| | | | | | | | | | | | | | | | This patch allows users to enable/disable internal TX and/or RX clock delay for BCM54616S PHYs so as to satisfy RGMII timing specifications. On a particular platform, whether TX and/or RX clock delay is required depends on how PHY connected to the MAC IP. This requirement can be specified through "phy-mode" property in the platform device tree. The patch is inspired by commit 733336262b28 ("net: phy: Allow BCM5481x PHYs to setup internal TX/RX clock delay"). Signed-off-by: Tao Ren <taoren@fb.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: realtek: fix RTL8201F sysfs nameHolger Hoffstätte2018-11-051-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Since 4.19 the following error in sysfs has appeared when using the r8169 NIC driver: $cd /sys/module/realtek/drivers $ls -l ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory [..garbled dir entries follow..] Apparently the forward slash in "10/100Mbps Ethernet" is interpreted as directory separator that leads nowhere, and was introduced in commit 513588dd44b ("net: phy: realtek: add RTL8201F phy-id and functions"). Fix this by removing the offending slash in the driver name. Other drivers in net/phy seem to have the same problem, but I cannot test/verify them. Fixes: 513588dd44b ("net: phy: realtek: add RTL8201F phy-id and functions") Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: genphy_10g_driver: Avoid NULL pointer dereferenceAndrew Lunn2018-10-261-1/+1
| | | | | | | | | | | | This driver got missed during the recent change of .features from a u32 to a pointer to a Linux bitmap. Change the initialisation from 0 to PHY_10GBIT_FEATURES so removing the danger of a NULL pointer dereference. Fixes: 719655a14971 ("net: phy: Replace phy driver features u32 with link_mode bitmap") Reported-by: Jose Abreu <jose.abreu@synopsys.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds2018-10-2420-367/+1997
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull networking updates from David Miller: 1) Add VF IPSEC offload support in ixgbe, from Shannon Nelson. 2) Add zero-copy AF_XDP support to i40e, from Björn Töpel. 3) All in-tree drivers are converted to {g,s}et_link_ksettings() so we can get rid of the {g,s}et_settings ethtool callbacks, from Michal Kubecek. 4) Add software timestamping to veth driver, from Michael Walle. 5) More work to make packet classifiers and actions lockless, from Vlad Buslov. 6) Support sticky FDB entries in bridge, from Nikolay Aleksandrov. 7) Add ipv6 version of IP_MULTICAST_ALL sockopt, from Andre Naujoks. 8) Support batching of XDP buffers in vhost_net, from Jason Wang. 9) Add flow dissector BPF hook, from Petar Penkov. 10) i40e vf --> generic iavf conversion, from Jesse Brandeburg. 11) Add NLA_REJECT netlink attribute policy type, to signal when users provide attributes in situations which don't make sense. From Johannes Berg. 12) Switch TCP and fair-queue scheduler over to earliest departure time model. From Eric Dumazet. 13) Improve guest receive performance by doing rx busy polling in tx path of vhost networking driver, from Tonghao Zhang. 14) Add per-cgroup local storage to bpf 15) Add reference tracking to BPF, from Joe Stringer. The verifier can now make sure that references taken to objects are properly released by the program. 16) Support in-place encryption in TLS, from Vakul Garg. 17) Add new taprio packet scheduler, from Vinicius Costa Gomes. 18) Lots of selftests additions, too numerous to mention one by one here but all of which are very much appreciated. 19) Support offloading of eBPF programs containing BPF to BPF calls in nfp driver, frm Quentin Monnet. 20) Move dpaa2_ptp driver out of staging, from Yangbo Lu. 21) Lots of u32 classifier cleanups and simplifications, from Al Viro. 22) Add new strict versions of netlink message parsers, and enable them for some situations. From David Ahern. 23) Evict neighbour entries on carrier down, also from David Ahern. 24) Support BPF sk_msg verdict programs with kTLS, from Daniel Borkmann and John Fastabend. 25) Add support for filtering route dumps, from David Ahern. 26) New igc Intel driver for 2.5G parts, from Sasha Neftin et al. 27) Allow vxlan enslavement to bridges in mlxsw driver, from Ido Schimmel. 28) Add queue and stack map types to eBPF, from Mauricio Vasquez B. 29) Add back byte-queue-limit support to r8169, with all the bug fixes in other areas of the driver it works now! From Florian Westphal and Heiner Kallweit. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2147 commits) tcp: add tcp_reset_xmit_timer() helper qed: Fix static checker warning Revert "be2net: remove desc field from be_eq_obj" Revert "net: simplify sock_poll_wait" net: socionext: Reset tx queue in ndo_stop net: socionext: Add dummy PHY register read in phy_write() net: socionext: Stop PHY before resetting netsec net: stmmac: Set OWN bit for jumbo frames arm64: dts: stratix10: Support Ethernet Jumbo frame tls: Add maintainers net: ethernet: ti: cpsw: unsync mcast entries while switch promisc mode octeontx2-af: Support for NIXLF's UCAST/PROMISC/ALLMULTI modes octeontx2-af: Support for setting MAC address octeontx2-af: Support for changing RSS algorithm octeontx2-af: NIX Rx flowkey configuration for RSS octeontx2-af: Install ucast and bcast pkt forwarding rules octeontx2-af: Add LMAC channel info to NIXLF_ALLOC response octeontx2-af: NPC MCAM and LDATA extract minimal configuration octeontx2-af: Enable packet length and csum validation octeontx2-af: Support for VTAG strip and capture ...
| * net: phy: phy_support_sym_pause: Clear Asym PauseAndrew Lunn2018-10-231-0/+1
| | | | | | | | | | | | | | | | | | | | | | When indicating the MAC supports Symmetric Pause, clear the Asymmetric Pause bit, which could of been already set is the PHY supports it. Reported-by: Labbe Corentin <clabbe@baylibre.com> Fixes: c306ad36184f ("net: ethernet: Add helper for MACs which support pause") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: phy: mdio-mux-bcm-iproc: simplify getting .driver_dataWolfram Sang2018-10-221-4/+2Star
| | | | | | | | | | | | | | | | | | We should get 'driver_data' from 'struct device' directly. Going via platform_device is an unneeded step back and forth. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: phy: micrel: add Microchip KSZ9131 initial driverYuiko Oshino2018-10-201-1/+129
| | | | | | | | | | | | | | Add support for Microchip Technology KSZ9131 10/100/1000 Ethernet PHY Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: phy: mscc: fix memory leak in vsc8574_config_pre_initGustavo A. R. Silva2018-10-181-1/+1
| | | | | | | | | | | | | | | | | | | | | | In case memory resources for *fw* were successfully allocated, release them before return. Addresses-Coverity-ID: 1473968 ("Resource leak") Fixes: 00d70d8e0e78 ("net: phy: mscc: add support for VSC8574 PHY") Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: phy: mscc: fix signedness bug in vsc85xx_downshift_getGustavo A. R. Silva2018-10-181-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, the error handling for the call to function phy_read_paged() doesn't work because *reg_val* is of type u16 (16 bits, unsigned), which makes it impossible for it to hold a value less than 0. Fix this by changing the type of variable *reg_val* to int. Addresses-Coverity-ID: 1473970 ("Unsigned compared against 0") Fixes: 6a0bfbbe20b0 ("net: phy: mscc: migrate to phy_select/restore_page functions") Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: phy: merge phy_start_aneg and phy_start_aneg_privHeiner Kallweit2018-10-161-18/+3Star
| | | | | | | | | | | | | | | | | | After commit 9f2959b6b52d ("net: phy: improve handling delayed work") the sync parameter isn't needed any longer in phy_start_aneg_priv(). This allows to merge phy_start_aneg() and phy_start_aneg_priv(). Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: phy: simplify handling of PHY_RESUMING in state machineHeiner Kallweit2018-10-161-29/+14Star
| | | | | | | | | | | | | | | | Simplify code for handling state PHY_RESUMING, no functional change intended. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: phy: improve handling of PHY_RUNNING in state machineHeiner Kallweit2018-10-161-20/+9Star
| | | | | | | | | | | | | | | | | | | | | | | | Handling of state PHY_RUNNING seems to be more complex than it needs to be. If not polling, then we don't have to do anything, we'll receive an interrupt and go to state PHY_CHANGELINK once the link goes down. If polling and link is down, we don't have to go the extra mile over PHY_CHANGELINK and call phy_read_status() again but can set status PHY_NOLINK directly. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: phy: trigger state machine immediately in phy_start_machineHeiner Kallweit2018-10-161-1/+1
| | | | | | | | | | | | | | | | | | | | When starting the state machine there may be work to be done immediately, e.g. if the initial state is PHY_UP then the state machine may trigger an autonegotiation. Having said that I see no need to wait a second until the state machine is run first time. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2018-10-131-2/+0Star
| |\ | | | | | | | | | | | | | | | | | | | | | Conflicts were easy to resolve using immediate context mostly, except the cls_u32.c one where I simply too the entire HEAD chunk. Signed-off-by: David S. Miller <davem@davemloft.net>
| * | net: phy: mscc: add support for VSC8574 PHYQuentin Schulz2018-10-081-1/+319
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | net: phy: mscc: add support for VSC8584 PHYQuentin Schulz2018-10-081-0/+747
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | net: phy: mscc: remove unneeded temporary variableQuentin Schulz2018-10-081-8/+4Star
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Here, the rc variable is either used only for the condition right after the assignment or right before being used as the return value of the function it's being used in. So let's remove this unneeded temporary variable whenever possible. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | net: phy: mscc: shorten `x != 0` condition to `x`Quentin Schulz2018-10-081-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | `if (x != 0)` is basically a more verbose version of `if (x)` so let's use the latter so it's consistent throughout the whole driver. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | net: phy: mscc: remove unneeded parenthesisQuentin Schulz2018-10-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The == operator precedes the || operator, so we can remove the parenthesis around (a == b) || (c == d). The condition is rather explicit and short so removing the parenthesis definitely does not make it harder to read. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | net: phy: mscc: Add EEE init sequenceRaju Lakkaraju2018-10-081-0/+65
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Microsemi PHYs (VSC 8530/31/40/41) need to update the Energy Efficient Ethernet initialization sequence. In order to avoid certain link state errors that could result in link drops and packet loss, the physical coding sublayer (PCS) must be updated with settings related to EEE in order to improve performance. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | net: phy: mscc: add ethtool statistics countersRaju Lakkaraju2018-10-081-0/+119
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are a few counters available in the PHY: receive errors, false carriers, link disconnects, media CRC errors and valids counters. So let's expose those in the PHY driver. Use the priv structure as the next PHY to be supported has a few additional counters. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | net: phy: mscc: migrate to phy_select/restore_page functionsQuentin Schulz2018-10-081-84/+62Star
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Microsemi PHYs have multiple banks of registers (called pages). Registers can only be accessed from one page, if we need a register from another page, we need to switch the page and the registers of all other pages are not accessible anymore. Basically, to read register 5 from page 0, 1, 2, etc., you do the same phy_read(phydev, 5); but you need to set the desired page beforehand. In order to guarantee that two concurrent functions do not change the page, we need to do some locking per page. This can be achieved with the use of phy_select_page and phy_restore_page functions but phy_write/read calls in-between those two functions shall be replaced by their lock-free alternative __phy_write/read. Let's migrate this driver to those functions. Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2018-10-061-20/+28
| |\ \
| * \ \ Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2018-10-042-5/+14
| |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net' overlapped the renaming of a netlink attribute in net-next. Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | net: phy: Convert to using %pOFn instead of device_node.nameRob Herring2018-10-021-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In preparation to remove the node name pointer from struct device_node, convert printf users to use the %pOFn format specifier. Cc: Andrew Lunn <andrew@lunn.ch> Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | net: phy: improve handling delayed workHeiner Kallweit2018-10-021-14/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Using mod_delayed_work() allows to simplify handling delayed work and removes the need for the sync parameter in phy_trigger_machine(). Also introduce a helper phy_queue_state_machine() to encapsulate the low-level delayed work calls. No functional change intended. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | net: phy: Replace phy driver features u32 with link_mode bitmapAndrew Lunn2018-10-026-29/+171
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is one step in allowing phylib to make use of link_mode bitmaps, instead of u32 for supported and advertised features. Convert the phy drivers to use bitmaps to indicates the features they support. Build bitmap equivalents of the u32 values at runtime, and have the drivers point to the appropriate bitmap. These bitmaps are shared, and we don't want a driver to modify them. So mark them __ro_after_init. Within phylib, the features bitmap is currently turned back into a u32. This will be removed once the whole of phylib, and the drivers are converted to use bitmaps. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | net: phy: Add phydev_info()Andrew Lunn2018-10-022-7/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add phydev_info() and make use of it within the phy drivers and core code. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | net: phy: Add phydev_warn()Andrew Lunn2018-10-025-24/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Not all new style LINK_MODE bits can be converted into old style SUPPORTED bits. We need to warn when such a conversion is attempted. Add a helper for this. Convert all pr_warn() calls to phydev_warn() where possible. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | net: phy: Move linkmode helpers to somewhere publicAndrew Lunn2018-10-021-27/+0Star
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | phylink has some useful helpers to working with linkmode bitmaps. Move them to there own header so other code can use them. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | net: phy: mdio-bcm-unimac: mark PM functions as __maybe_unusedArnd Bergmann2018-09-281-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The newly added runtime-pm support causes a harmless warning when CONFIG_PM is disabled: drivers/net/phy/mdio-bcm-unimac.c:330:12: error: 'unimac_mdio_resume' defined but not used [-Werror=unused-function] static int unimac_mdio_resume(struct device *d) drivers/net/phy/mdio-bcm-unimac.c:321:12: error: 'unimac_mdio_suspend' defined but not used [-Werror=unused-function] static int unimac_mdio_suspend(struct device *d) Marking the functions as __maybe_unused is the easiest workaround and avoids adding #ifdef checks. Fixes: b78ac6ecd1b6 ("net: phy: mdio-bcm-unimac: Allow configuring MDIO clock divider") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | phy: mscc: fix printf formatArnd Bergmann2018-09-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | gcc points out that the length of the temporary buffer may not be sufficient for large numbers of leds: drivers/net/phy/mscc.c: In function 'vsc85xx_probe': drivers/net/phy/mscc.c:460:45: error: '-mode' directive writing 5 bytes into a region of size between 0 and 9 [-Werror=format-overflow=] ret = sprintf(led_dt_prop, "vsc8531,led-%d-mode", i); ^~~~~ drivers/net/phy/mscc.c:460:9: note: 'sprintf' output between 19 and 28 bytes into a destination of size 22 ret = sprintf(led_dt_prop, "vsc8531,led-%d-mode", i); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ While we can make a reasonable assumption that the number of LEDs is small, the cost of making the buffer a little bigger is insignificant as well. Fixes: 11bfdabb7ff5 ("net: phy: mscc: factorize code for LEDs mode") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | net: phy: marvell: Fix build.David S. Miller2018-09-261-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Local variable 'autoneg' doesn't even exist: drivers/net/phy/marvell.c: In function 'm88e1121_config_aneg': drivers/net/phy/marvell.c:468:25: error: 'autoneg' undeclared (first use in this function); did you mean 'put_net'? if (phydev->autoneg != autoneg || changed) { ^~~~~~~ Fixes: d6ab93364734 ("net: phy: marvell: Avoid unnecessary soft reset") Reported-by:Vakul Garg <vakul.garg@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | net: phy: marvell: Avoid unnecessary soft resetFlorian Fainelli2018-09-261-42/+21Star
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The BMCR.RESET bit on the Marvell PHYs has a special meaning in that it commits the register writes into the HW for it to latch and be configured appropriately. Doing software resets causes link drops, and this is unnecessary disruption if nothing changed. Determine from marvell_set_polarity()'s return code whether the register value was changed and if it was, propagate that to the logic that hits the software reset bit. This avoids doing unnecessary soft reset if the PHY is configured in the same state it was previously, this also eliminates the need for a m88e1111_config_aneg() function since it now is the same as marvell_config_aneg(). Tested-by: Wang, Dongsheng <dongsheng.wang@hxt-semitech.com> Tested-by: Chris Healy <cphealy@gmail.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | net: phy: Stop with excessive soft resetFlorian Fainelli2018-09-261-2/+0Star
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While consolidating the PHY reset in phy_init_hw() an unconditionaly BMCR soft-reset I became quite trigger happy with those. This was later on deactivated for the Generic PHY driver on the premise that a prior software entity (e.g: bootloader) might have applied workarounds in commit 0878fff1f42c ("net: phy: Do not perform software reset for Generic PHY"). Since we have a hook to wire-up a soft_reset callback, just use that and get rid of the call to genphy_soft_reset() entirely. This speeds up initialization and link establishment for most PHYs out there that do not require a reset. Fixes: 87aa9f9c61ad ("net: phy: consolidate PHY reset in phy_init_hw()") Tested-by: Wang, Dongsheng <dongsheng.wang@hxt-semitech.com> Tested-by: Chris Healy <cphealy@gmail.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | Merge ra.kernel.org:/pub/scm/linux/kernel/git/davem/netDavid S. Miller2018-09-251-2/+2
| |\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Version bump conflict in batman-adv, take what's in net-next. iavf conflict, adjustment of netdev_ops in net-next conflicting with poll controller method removal in net. Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | net: phy: mdio-bcm-unimac: Allow configuring MDIO clock dividerFlorian Fainelli2018-09-221-2/+81
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Allow the configuration of the MDIO clock divider when the Device Tree contains 'clock-frequency' property (similar to I2C and SPI buses). Because the hardware may have lost its state during suspend/resume, re-apply the MDIO clock divider upon resumption. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | net: phy: don't reschedule state machine when PHY is haltedHeiner Kallweit2018-09-221-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When being in state PHY_HALTED we don't have to reschedule the state machine, phy_start() will start it again. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | net: phy: phylink: ensure the carrier is off when starting phylinkAntoine Tenart2018-09-201-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Phylink made an assumption about the carrier state being down when calling phylink_start(). If this assumption isn't satisfied, the internal phylink state could misbehave and a net device could end up not being functional. This patch fixes this by explicitly calling netif_carrier_off() in phylink_start(). Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | net: phy: call state machine synchronously in phy_stopHeiner Kallweit2018-09-201-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | phy_stop() may be called e.g. when suspending, therefore all needed actions should be performed synchronously. Therefore add a synchronous call to the state machine. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | net: mdio: remove duplicated include from mdio_bus.cYueHaibing2018-09-181-1/+0Star
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove duplicated include linux/gpio/consumer.h Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | net: phy: et011c: Remove incorrect PHY_POLL flagsFlorian Fainelli2018-09-171-1/+0Star
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | PHY_POLL is defined as -1 which means that we would be setting all flags of the PHY driver, this is also not a valid flag to tell PHYLIB about, just remove it. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | net: ethernet: Add helper to determine if pause configuration is supportedAndrew Lunn2018-09-131-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rather than have MAC drivers open code the test, add a helper in phylib. This will help when we change the type of phydev->supported. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | net: ethernet: Add helper for set_pauseparam for PauseAndrew Lunn2018-09-131-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ethtool can be used to enable/disable pause. Add a helper to configure the PHY when Pause is supported. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | net: ethernet: Add helper for set_pauseparam for Asym PauseAndrew Lunn2018-09-131-0/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ethtool can be used to enable/disable pause. Add a helper to configure the PHY when asym pause is supported. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | net: ethernet: Add helper for MACs which support pauseAndrew Lunn2018-09-131-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rather than have the MAC drivers manipulate phydev members, add a helper function for MACs supporting Pause, but not Asym Pause. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | net: ethernet: Add helper for MACs which support asym pauseAndrew Lunn2018-09-131-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rather than have the MAC drivers manipulate phydev members to indicate they support Asym Pause, add a helper function. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3-55-g7522 (git 2.39.0) at 2024-07-04 14:56:33 +0200