summaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/ath/ath9k/eeprom_def.c
Commit message (Collapse)AuthorAgeFilesLines
* ath9k_hw: Add dump_eeprom support for eeprom_defRajkumar Manoharan2011-08-091-0/+131
| | | | | Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: fix calculated runtime tx power limitFelix Fietkau2011-08-081-11/+0Star
| | | | | | | | Use the previously calculated maximum of all rates instead of just the one from the lowest rate of the selected PHY mode. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: remove the tx power index offsetFelix Fietkau2011-08-081-6/+2Star
| | | | | | | It is always 0 Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: use get_unaligned_{b16, le16, le32} where possiblePavel Roskin2011-07-181-7/+5Star
| | | | | Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Drag the driver to the year 2011Sujith Manoharan2011-05-191-1/+1
| | | | | | | The Times They Are a-Changin'. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: fix AR9160 xpaBiasLvlFreq endianness handlingAdrian Chadd2011-04-261-0/+4
| | | | | | | | | The xpaBiasLvlFreq parameter array is made up of 16 bit words which aren't byte-swapped like the other 16-bit eeprom parameters are. It's only used by the AR9160. Signed-off-by: Adrian Chadd <adrian@freebsd.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: Speedup register ops for HTC driverRajkumar Manoharan2011-03-301-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | Fine-tuning register write operation and avoid unnecessay delays for ath9k_htc driver, saves hw reset time which improves scanning time and also solves one of the following scenario. Sometimes the ACK is sent by STA for assoc response is not seen at AP side. So the AP continues to send retry assoc responses. At the STA side, since the assoc response was already forwarded to mac80211, it proceeded to channel change which in turns does chip reset. In most of the cases the chip reset was completed before max retries are reached at AP side. Hence STA can able to ACK the retried frames again. But in clear environment these retries are completed within shortspan of time. Since ath9k_htc consumes more time for hw reset, this latency is causing dissociation by AP due to max reties are reached. This issue was originally reported with Cisco Aironet 1250 AP in HT40 mode in noise free environment. Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: Fix INI fixupSujith Manoharan2011-01-281-3/+3
| | | | | | | | | Commit "ath9k_hw: move AR9280 PCI EEPROM fix to eeprom_def.c" changed the behavior of INI overriding which is needed only for PCI cards. Revert to the original check. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: Offload USB eeprom reading to targetSujith Manoharan2011-01-191-3/+29
| | | | | | | | | For USB devices, reading the EEPROM data can be offloaded to the target. Use multiple register reads to take advantage of this feature to reduce initialization time. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: Fix thermal issue with UB94Sujith Manoharan2011-01-101-0/+4
| | | | | | | | Hardcode the output voltage of x-PA bias LDO to the lowest value for UB94. The card doesn't get too hot now. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: remove antenna configuration eeprom ops and variablesFelix Fietkau2010-12-131-32/+1Star
| | | | | | | | | | | | AR9280 based hardware with 3 antennas and slow antenna diversity has not been seen in the wild and ath9k does not support that form of antenna diversity, so remove the EEPROM ops for it. These EEPROM ops are currently only used for setting the AR_PHY_SWITCH_COM register, which is being done in the EEPROM specific file already. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: merge ath9k_hw_get_gain_boundaries_pdadcs between eeprom_def.c and ↵Felix Fietkau2010-12-131-163/+1Star
| | | | | | | eeprom_4k.c Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: clean up duplicate and unnused eeprom related definesFelix Fietkau2010-12-131-9/+9
| | | | | | | | | | AR*_MAX_RATE_POWER => MAX_RATE_POWER AR*_EEPROM_MODAL_SPURS => AR_EEPROM_MODAL_SPURS AR*_OPFLAGS_* => AR5416_OPFLAGS_* ... Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Merge branch 'master' of ↵John W. Linville2010-12-081-4/+8
|\ | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 Conflicts: drivers/net/wireless/ath/ath9k/ath9k.h drivers/net/wireless/ath/ath9k/main.c drivers/net/wireless/ath/ath9k/xmit.c
| * ath9k: fix bug in tx powerMatteo Croce2010-12-071-4/+8
| | | | | | | | | | | | | | | | | | | | | | The ath9k driver subtracts 3 dBm to the txpower as with two radios the signal power is doubled. The resulting value is assigned in an u16 which overflows and makes the card work at full power. Cc: stable@kernel.org Signed-off-by: Matteo Croce <matteo@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath: Convert ath_print to ath_dbgJoe Perches2010-12-071-27/+26Star
| | | | | | | | | | | | | | | | | | | | | | Remove ath/debug.h and the includes of these files. Coalesce long formats. Correct a few misspellings and missing "\n"s from these logging messages. Remove unnecessary trailing space before a newline. Remove ARRAY_SIZE casts, use printf type %zu Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath: Convert ath_print(.., ATH_DBG_FATAL to ath_errJoe Perches2010-12-071-8/+6Star
| | | | | | | | | | | | | | | | So these errors are always emitted at KERN_ERR level. Remove ARRAY_SIZE casts, use printf type %zu Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | Merge branch 'master' of ↵John W. Linville2010-12-021-5/+6
|\| | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 Conflicts: drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
| * ath9k_hw: fix more bitfield related endian issuesFelix Fietkau2010-12-021-5/+6
| | | | | | | | | | | | | | | | | | A few LNA control related flags were also specified as a bitfields, however for some strange reason they were written in big-endian order this time. Fix this by using flags instead. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k: Use static constJoe Perches2010-11-221-7/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Using static const generally increases object text and decreases data size. It also generally decreases overall object size. text data bss dec hex filename 11161 56 2136 13353 3429 drivers/net/wireless/ath/ath9k/ar9003_paprd.o.new 11167 56 2136 13359 342f drivers/net/wireless/ath/ath9k/ar9003_paprd.o.old 15428 56 3056 18540 486c drivers/net/wireless/ath/ath9k/eeprom_4k.o.old 15451 56 3056 18563 4883 drivers/net/wireless/ath/ath9k/eeprom_4k.o.new 14087 56 2560 16703 413f drivers/net/wireless/ath/ath9k/eeprom_9287.o.old 14036 56 2560 16652 410c drivers/net/wireless/ath/ath9k/eeprom_9287.o.new 10041 56 2384 12481 30c1 drivers/net/wireless/ath/ath9k/ani.o.new 10088 56 2384 12528 30f0 drivers/net/wireless/ath/ath9k/ani.o.old 9316 1580 2304 13200 3390 drivers/net/wireless/ath/ath9k/htc_drv_init.o.new 9316 1580 2304 13200 3390 drivers/net/wireless/ath/ath9k/htc_drv_init.o.old 16483 56 3432 19971 4e03 drivers/net/wireless/ath/ath9k/ar9003_phy.o.new 16517 56 3432 20005 4e25 drivers/net/wireless/ath/ath9k/ar9003_phy.o.old 18221 104 2960 21285 5325 drivers/net/wireless/ath/ath9k/rc.o.old 18203 104 2960 21267 5313 drivers/net/wireless/ath/ath9k/rc.o.new 19985 56 4288 24329 5f09 drivers/net/wireless/ath/ath9k/eeprom_def.o.new 20040 56 4288 24384 5f40 drivers/net/wireless/ath/ath9k/eeprom_def.o.old 23997 56 4984 29037 716d drivers/net/wireless/ath/ath9k/ar5008_phy.o.old 23846 56 4984 28886 70d6 drivers/net/wireless/ath/ath9k/ar5008_phy.o.new 24285 56 3184 27525 6b85 drivers/net/wireless/ath/ath9k/ar9003_eeprom.o.old 24101 56 3184 27341 6acd drivers/net/wireless/ath/ath9k/ar9003_eeprom.o.new 6834 56 1032 7922 1ef2 drivers/net/wireless/ath/ath9k/ar9002_phy.o.old 6780 56 1032 7868 1ebc drivers/net/wireless/ath/ath9k/ar9002_phy.o.new 36211 64 8624 44899 af63 drivers/net/wireless/ath/ath9k/hw.o.new 36401 64 8624 45089 b021 drivers/net/wireless/ath/ath9k/hw.o.old 9281 56 1496 10833 2a51 drivers/net/wireless/ath/ath9k/ar9003_calib.o.old 9150 56 1496 10702 29ce drivers/net/wireless/ath/ath9k/ar9003_calib.o.new Use ARRAY_SIZE instead of a magic number. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | ath9k_hw: extend ath9k_hw_set_txpowerlimit to test channel txpowerFelix Fietkau2010-11-151-29/+33
|/ | | | | | | | | ath9k_hw_set_txpowerlimit gets an extra boolean parameter that - if set - causes the rate txpower table and the regulatory limit to be calculated and stored, without changing hardware registers. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: simplify revision checks for AR9280Felix Fietkau2010-09-271-9/+9
| | | | | | | | | Since AR9280 v1.0 was never sold (and the initvals removed), v1.0 specific revision checks can be removed and the 'v2.0 or later' check can be simplified to a check for AR9280 or later. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: remove warning in ath9k_hw_def_get_num_ant_configRajkumar Manoharan2010-09-161-2/+2
| | | | | | | | | | | This patch fixes following warning drivers/net/wireless/ath/ath9k/eeprom_def.c: In function 'ath9k_hw_def_get_num_ant_config' drivers/net/wireless/ath/ath9k/eeprom_def.c:1425:47: warning: comparison between 'enum ath9k_hal_freq_band' and 'enum ieee80211_band' Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: remove unneeded calculation of minimal calibration powerPavel Roskin2010-07-141-5/+2Star
| | | | | | | | | | | Remove tMinCalPower from ath9k_hw_set_def_power_cal_table(), as it's never used. Remove corresponding arguments of the functions calculating that value. Original patch by Prarit Bhargava <prarit@redhat.com> Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: fix an off-by-one error in the PDADC boundaries calculationFelix Fietkau2010-07-121-1/+1
| | | | | | | | | | PDADC values were only generated for values surrounding the target index, however not for the target index itself, leading to a minor error in the generated curve. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: fix antenna diversity on AR9285Felix Fietkau2010-07-121-2/+2
| | | | | | | | | | | | | On AR9285, the antenna switch configuration register uses more than just 16 bits. Because of an arbitrary mask applied to the EEPROM value that stores this configuration, diversity was broken in some cases, leading to a significant degradation in signal strength. Fix this by changing the callback to return a 32 bit value and remove the arbitrary mask. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath: Fix uninitialized variable warningsPrarit Bhargava2010-06-071-0/+1
| | | | | | | | | | | | | | Fixes 'make -j24 CONFIG_DEBUG_SECTION_MISMATCH=y' warning: drivers/net/wireless/ath/ath9k/eeprom_4k.c: In function ‘ath9k_hw_get_4k_gain_boundaries_pdadcs.clone.1’: drivers/net/wireless/ath/ath9k/eeprom_4k.c:311: error: ‘minPwrT4’ may be used uninitialized in this function drivers/net/wireless/ath/ath9k/eeprom_9287.c: In function ‘ath9k_hw_get_AR9287_gain_boundaries_pdadcs’: drivers/net/wireless/ath/ath9k/eeprom_9287.c:302: error: ‘minPwrT4’ may be used uninitialized in this function drivers/net/wireless/ath/ath9k/eeprom_def.c: In function ‘ath9k_hw_get_def_gain_boundaries_pdadcs.clone.0’: drivers/net/wireless/ath/ath9k/eeprom_def.c:679: error: ‘minPwrT4’ may be used uninitialized in this function Signed-off-by: Prarit Bhargava <prarit@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* drivers/net: Remove unnecessary returns from void function()sJoe Perches2010-05-141-3/+0Star
| | | | | | | | | | | | | | | | | | | | | | This patch removes from drivers/net/ all the unnecessary return; statements that precede the last closing brace of void functions. It does not remove the returns that are immediately preceded by a label as gcc doesn't like that. It also does not remove null void functions with return. Done via: $ grep -rP --include=*.[ch] -l "return;\n}" net/ | \ xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }' with some cleanups by hand. Compile tested x86 allmodconfig only. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ath9k_hw: update EEPROM data structure for AR9280Felix Fietkau2010-04-271-0/+2
| | | | | | | Adds read access for the 5 GHz fast clock flag Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: move AR9280 PCI EEPROM fix to eeprom_def.cFelix Fietkau2010-04-161-0/+6
| | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: restore mac address reading logicLuis R. Rodriguez2010-04-161-3/+3
| | | | | | | | | | | | | | | | | | Once upon a time the AR_EEPROM_MAC macro was added to let us add a random attribute to the three 4-bytes of MAC addresses entries we read from the EEPROM. This was good while a random high-enough value was used which did not conflict with any of the already existing enum eeprom_param values. With AR9003 support the enums overlap and it means we either increment the random offset or just restore the reading logic to match what the HAL has. I choose to do the later to synchronize the logic on both code bases. This should fix reading the MAC address from the EEPROM on AR9003 hardware. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: Move some RF ops to the private callbacksLuis R. Rodriguez2010-04-161-0/+1
| | | | | | | | | | | | | | The PHY split is easier done in a few steps. First move the RF ops to the private ops and rename them accordingly. We split PHY stuff up first for the AR5008 and AR9002 families. There are some callbacks that AR9002 share with the AR5008 familiy so we set those first, if AR9002 has some different callbacks it will override them upon hardware init. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Fix bugs in handling TX powerSenthil Balasubramanian2009-10-071-4/+98
| | | | | | | | | | | * Get power table offset from the EEPROM instead of using a hardcoded value of -5 if the EEPROM rev is >= 21. * Add support in the 4k eeprom code for tx power offset in case we have a 4k AR9280 implementation. * Fix tx power accuracy at high powers. Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* atheros: move bus ops to ath_commonLuis R. Rodriguez2009-10-071-2/+3
| | | | | | | | This is the last part to make ath9k hw code core driver agnostic. I believe ath9k_htc can now use use the hw code unmodified. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: clarify what hw code is and remove ath9k.h from a few filesLuis R. Rodriguez2009-10-071-1/+0Star
| | | | | | | | hw code will be shared between ath9k and ath9k_htc. Just a few more files are left to clean up, mark them as well. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* atheros: add common debug printingLuis R. Rodriguez2009-10-071-36/+39
| | | | | | | | | | | ath9k uses this for now, ath9k_htc is expected to re-use this as well. We lave ath5k as is, but it certainly can also be converted later. The ath9k module parameter and debugfs entry is kept. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: use ath_hw for DPRINTF() and debug init/exitLuis R. Rodriguez2009-10-071-12/+12
| | | | | | | | | | DPRINTF() is used in hw specific related code, as such ensure we don't rely on the private driver core ath_softc struct when calling it. Drivers can then implement their own DPRINTF() as they see fit. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Fix bug in chain handlingSenthil Balasubramanian2009-09-231-1/+3
| | | | | | | | | | | * This patch fixes a bug in calculating the scaled power for three chain chipsets. * Also, a delay is needed after setting DAC low-power mode in TOP1 RF register (Top Level Register Bits). Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath: move regulatory info into shared common structureLuis R. Rodriguez2009-08-201-6/+8
| | | | | | | | | This moves the shared regulatory structure into the common structure. We will use this ongoing for common data. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Split eeprom.c into manageable piecesSujith2009-08-141-0/+1385
Add eeprom_def.c, eeprom_4k.c and eeprom_9287.c This improves maintainability. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3-55-g7522 (git 2.39.0) at 2024-10-09 18:24:50 +0200