summaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/rsi/rsi_main.h
Commit message (Collapse)AuthorAgeFilesLines
* rsi: resolve power save issue after S4 resumeSiva Rebbagondla2019-02-081-0/+1
| | | | | | | | | | | We are redownloading the firmware after S4 restore and observed in stress test that mac80211 sometimes gives power save request after resume which causes the firmware in bad state. mac_ops_resumed flag is added to skip that request until initialisation is done and Keeping power save state is NONE. Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: add support for hardware scan offloadPrameela Rani Garnepudi2019-01-101-0/+22
| | | | | | | | | | | | | | | With the current approach of scanning, roaming delays are observed. Firmware has support for back ground scanning. To get this advantage, mac80211 hardware scan is implemented, which decides type of scan to do based on connected state. When station is in not connected, driver returns with special value 1 to trigger software scan in mac80211. In case of connected state, background scan will be triggered. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: roaming enhancementsPrameela Rani Garnepudi2018-04-241-0/+1
| | | | | | | | | | | | | | | | To support roaming below changes are done: * Station notify frame is send to firmware after sending assoc request. This will avoid dropping of first EAPOL frame due to delay in creation of station control block in firmware. * Data queues are unblocked after sending station notify in open mode, after configuring key in WEP mode, and after receiving EAPOL4 confirm in WPA mode. * Initial EAPOL frames priority is chaged to MGMT, rekey EAPOL frames priority changed to VO. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: move xtend_desc structure from rsi_main.h to rsi_mgmt.hPrameela Rani Garnepudi2018-04-241-6/+0Star
| | | | | | | | | | All descriptor structures are in rsi_mgmt.h except this extended descriptor structure. Hence moving it to rsi_mgmt.h and also renaming to rsi_xtend_desc. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: improve RX packet handling in USB interfacePrameela Rani Garnepudi2018-03-131-1/+0Star
| | | | | | | | | | | | | Curretly, RX packet processing is done sequencially. To improve the efficiency, RX skb queue is introduced. Here, while preparing RX URB skb is allocated and used for RX buffer. When rx done handler is called, enqueue the skb to rx_q and set the thread event. RX thread is modified to dequeue packets from skb queue and process further. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: improve RX handling in SDIO interfacePrameela Rani Garnepudi2018-03-131-0/+1
| | | | | | | | | | | | | Currently, RX packets are handled in interrupt context in SDIO interface. To improve the efficiency of processing RX packets, RX thread and RX skb queues are introduced. When the packet is read from device, driver prepares skb, add to RX queue and trigger RX thread event. RX thread processes the packets from RX queue. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: handle BT traffic in driverSiva Rebbagondla2018-03-131-0/+3
| | | | | | | | | | | | | | | | | BT frames are passed through coex and hal modules to BUS. After firmware is loaded, based on the operating mode CARD READY frame comes for each protocol. When BT card ready is received, BT attach is called. Protocol operations are exchanged between the modules at initialization time. Build flag CONFIG_RSI_COEX is introduced to enable coex support if CONFIG_BT_RSIHCI is enabled. Coex operations are valid if coex mode is greater than 1 only. Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com> Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: add coex supportPrameela Rani Garnepudi2018-03-131-0/+6
| | | | | | | | | | | | | | | | | With BT support, driver has to handle two streams of data (i.e. wlan and BT). Actual coex implementation is in firmware. Coex module just schedule the packets to firmware by taking them from the corresponding paths. Structures for module and protocol operations are introduced for this purpose. Protocol operations structure is global structure which can be shared among different modules. Move initialization of coex and operating mode values to rsi_91x_init(). Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: add header file rsi_91xPrameela Rani Garnepudi2018-03-131-10/+2Star
| | | | | | | | | | The common parameters used by wlan and bt modules are add to a new header file "rsi_91x.h" defined in 'include/net' Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: add rx control block to handle rx packets in USBPrameela Rani Garnepudi2018-03-131-1/+1
| | | | | | | | | | | Rx bluetooth endpoint shall be added in further patches. Rx control block is introduced here to handle Rx packets properly. Separate function is written to initialize the RX control blocks. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: sdio: Add WOWLAN support for S4 hibernate stateKarun Eagalapati2017-10-301-0/+4
| | | | | | | | | | | | We are disabling of interrupts from firmware in freeze handler. Also setting power management capability KEEP_MMC_POWER to make device wakeup for WoWLAN trigger. At restore, we observed a device reset on some platforms. Hence reloading of firmware and device initialization is performed. Signed-off-by: Karun Eagalapati <karun256@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: sdio: add WOWLAN support for S3 suspend stateKarun Eagalapati2017-10-301-1/+7
| | | | | | | | | | | WoWLAN is supported in RS9113 device through GPIO pin2. wowlan config frame is internally sent to firmware in mac80211 suspend handler. Also beacon miss threshold and keep-alive time values are increased to avoid un-necessary disconnection with AP. Signed-off-by: Karun Eagalapati <karun256@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: add version informationPavani Muthyala2017-09-251-4/+10
| | | | | | | | | We will dump information about firmware version, firmware file name and operating mode during initialization. Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: handle peer connection and disconnection in p2p modePrameela Rani Garnepudi2017-09-201-0/+2
| | | | | | | | | Parameter 'vif' is passed to inform_bss_status function to check the type of vif and to get vap_id. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: add support for p2p listenPrameela Rani Garnepudi2017-09-201-0/+2
| | | | | | | | | Remain-on-channel and cancel-remain-on-channel are implemented to support p2p listen phase. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: add/remove interface enhancements for p2pPrameela Rani Garnepudi2017-09-201-1/+5
| | | | | | | | | | | | STA_OPMODE and AP_OPMODE macros are renamed to RSI_OPMODE_STA and RSI_OPMODE_AP. New opmodes are added to this list for P2P support. Mapping of mac80211 interface types to rsi interface types are added. Add and remove interface callbacks are handled for P2P mode. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: security enhancements for AP modePrameela Rani Garnepudi2017-08-171-0/+1
| | | | | | | | | Station id should be set in load key frame configured to device. For WEP mode, key is configured once from mac80211. This key is saved and configured to device every time a station is connected. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: add beacon changes for AP modePrameela Rani Garnepudi2017-08-171-5/+8
| | | | | | | | | | | Mac80211 config parameter BEACON_ENABLE is handled. When VAP capabilities frame with AP mode is configured to firmware, beacon events start coming to host at each PreTBTT. At this time, beacon is taken from mac80211, descriptor is prepared and send to firmware. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: add interface changes for ap modePrameela Rani Garnepudi2017-08-171-0/+3
| | | | | | | | | | AP mode is handled in add_interface callback of mac80211. Also for AP mode, sending rx filter frame to disallow beacons to host is added. Station structures are initialized to NULL. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: advertise ap mode supportPrameela Rani Garnepudi2017-08-171-0/+10
| | | | | | | | | AP mode support is advertised to cfg80211. Necessary wiphy parameters are initialized. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: RTS threshold configurationKarun Eagalapati2017-08-081-0/+1
| | | | | | | | | Provision is added for configuring RTS threshold by sending vap dynamic update frame to firmware. Signed-off-by: Karun Eagalapati <karun256@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: add support for U-APSD power saveKarun Eagalapati2017-08-081-0/+1
| | | | | | | | | | This patch adds support for U-APSD power save. Configuration frame is downloaded to firmware with default settings and support is advertised to mac80211 Signed-off-by: Karun Eagalapati <karun256@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: add support for legacy power saveKarun Eagalapati2017-08-081-2/+7
| | | | | | | | | | This patch adds support for legacy power save. Necessary configuration frames are downloaded to firmware when power save is enabled/disabled Signed-off-by: Karun Eagalapati <karun256@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: regulatory enhancementsPrameela Rani Garnepudi2017-07-281-0/+8
| | | | | | | | | | | | Below regulatory changes are included this patch * Country code is saved as it will be used in bgscan. * Region codes are mapped according to RSI region codes. * Radar flag settings are moved under the check if 5GHZ band is enabled. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: update vap capabilities command framePrameela Rani Garnepudi2017-07-281-0/+3
| | | | | | | | | VAP capablities frame configured to device is modified to use common descriptor structure. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: Update in tx command frame radio capabilitiesPrameela Rani Garnepudi2017-07-281-1/+6
| | | | | | | | | | Radio capabilities frame is updated to use common descriptor structure. Also, few changes to this frame is done like hardware queues are increase to 12 from 8, default channel number is included. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: Rename mutex tx_rxlock to the tx_lock.Karun Eagalapati2017-07-281-2/+2
| | | | | | | | | | We have now added separate lock for Rx. This lock is used to protect tx path only Signed-off-by: Karun Eagalapati <karun256@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: use separate mutex lock for receive threadKarun Eagalapati2017-07-281-0/+2
| | | | | | | | | | | | | Deadlock issue is observed during our stress tests. The root cause for the issue is same lock is used between tx and rx threads. This patch adds a separate mutex lock for rx thread to resolve the problem. Signed-off-by: Karun Eagalapati <karun256@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: SDIO Rx packet processing enhancementKarun Eagalapati2017-07-281-0/+1
| | | | | | | | | | | | Newer firmware sends information about number of blocks through interrupt only. We don't need to read extra register for this. This patch adds needed driver changes for this enhancment. The change here is backward compatible Signed-off-by: Karun Eagalapati <karun256@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: separate function for management packet descriptorPrameela Rani Garnepudi2017-07-281-0/+7
| | | | | | | | Management descriptor preparation is move to a separate function as it will be called from a different context in upcoming patches. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: changes in eeprom read framePrameela Rani Garnepudi2017-07-281-0/+16
| | | | | | | | | | | EEPROM read frame is sent during device initialization to read mac address. The format of the frame is modified in firmware to include eeprom length and offset. This frame does not return firmware version now. Also same frame is sent again to read rf type and band information. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: use BUILD_BUG_ON check for fsm_stateAmitkumar Karwar2017-07-281-1/+3
| | | | | | | | | | Whenever new fsm_state enum element is added, fsm_state array also needs to be updated. If this change is missed, we may end up doing invalid access in array. BUILD_BUG_ON check will help to avoid this problem. Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: add tx frame for common device configurationPrameela Rani Garnepudi2017-06-211-1/+9
| | | | | | | | | | | | | | | After successful loading of firmware, a CARD READY indication is received by host. Common device configuration parameters are sent to the device after this. It includes information like device operating mode (Wi-Fi alone or BT coex), power save related parameters, GPIO information etc. As device supports BT coex, this frame is send in COEX queue initially. Based on the operating mode, CARD READY indication is received from each protocol module in firmware i.e. WLAN, BT. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: receive path enhancement for RS9113Prameela Rani Garnepudi2017-06-211-0/+1
| | | | | | | | | | RS9113 chipset supports Coex feature. Initial frame exchanges during device initialization happens on coex queue. This patch adds the handling for coex queue. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: Register interrupt handler before firmware loadPrameela Rani Garnepudi2017-06-211-0/+1
| | | | | | | | | | | | Before firmware load, sometimes false interrupts are received. System hang is observed if interrupt handler is not registered to receive these interrupts. Hence interrupt handler registration is moved before firmware load. We will drop these false interrupts as these are not from the device. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: use enum for FSM statesAmitkumar Karwar2017-06-211-7/+9
| | | | | | | | | Currently macros are used for FSM states. We will replace it with enum so that new state can be added easily without worrying about macro value. Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: Add new firmware loading methodPrameela Rani Garnepudi2017-05-241-0/+10
| | | | | | | | | | | | | | | | | The older firmware loading method has been deprecated and not in use for any chipets. New method is introduced which works based on soft boot loader. In this method, complete RAM image and FLASH image are present in the flash. Before loading the functional firmware, host issues boot loader commands to verify whether firmware to load is different from the current functional firmware. If not, firmware upgrade progresses and boot loader will switch to the new functional firmware. "rs9113_wlan_qspi.rps" is the firmware filename used in this patch. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: Add new host interface operationsPrameela Rani Garnepudi2017-05-241-0/+8
| | | | | | | | | | | Host interface opearation master_reg_read, master_reg_write and load_data_master_write are added. These functions are needed for the new firmware loading method. As part of this, the function master_access_msword is moved from rsi_91x_sdio_ops.c to rsi_91x_sdio.c. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: Add host interface operations as separate structure.Prameela Rani Garnepudi2017-05-241-2/+16
| | | | | | | | | | Host interface operations are currently function pointers in rsi_hw structure. As more host interface operations are going to be introduced, separate structure is added for these for convenience. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: Add support for 802.11dPrameela Rani Garnepudi2016-11-251-0/+1
| | | | | | | | | | Transmit power level in a channel is determined based on the dfs region. To support regulatory rules dfs region should be configured to device during set channel request. Also antenna gain values are taken from the mac80211 channel parameters instead of fixed values. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: Add support for antenna selectionPrameela Rani Garnepudi2016-11-251-0/+1
| | | | | | | | RSI 9113 device supports single antenna for tx and rx. Support for using external is added. This can be configured from user space using iw. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* rsi: Add support for configuring tx powerPrameela Rani Garnepudi2016-11-251-0/+2
| | | | | | | | | TX power can be configured from iwconfig, iw or from mac80211 when regulatory changes are done. Hence support for configuring tx power to device is added using the RADIO_PARAMS_UPDATE command frame. Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* cfg80211: remove enum ieee80211_bandJohannes Berg2016-04-121-1/+1
| | | | | | | | | This enum is already perfectly aliased to enum nl80211_band, and the only reason for it is that we get IEEE80211_NUM_BANDS out of it. There's no really good reason to not declare the number of bands in nl80211 though, so do that and remove the cfg80211 one. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* rsi: Adding support for host based bgscan.Jahnavi Meher2014-06-191-0/+9
| | | | | | | | | Added support for host based bgscan. The h/w queues are blocked while bgscan is being performed and after coming to the connected channel, the queues are unblocked. Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rsi: Changed the logic of dequeuing packets from hal queues.Jahnavi Meher2014-06-191-0/+3
| | | | | | | | | The number of packets being dequeued from s/w queues was fixed - changed it to a dynamic calculation based on txop. There are also some fixes to the dequeuing algorithm. Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rsi: Add pr_fmt,__printf, fix format & arg mismatchJoe Perches2014-03-191-1/+1
| | | | | | | | | | Emit a prefix for the rsi_dbg messages. Fix the format and argument mismatch and add __printf(2, 3) to try to avoid more. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rsi: make rsi_dbg a regular functionJohn W. Linville2014-03-181-15/+1Star
| | | | | | | | | | | | This is to address reports of this: In file included from drivers/net/wireless/rsi/rsi_mgmt.h:22:0, from drivers/net/wireless/rsi/rsi_91x_core.c:17: drivers/net/wireless/rsi/rsi_91x_core.c: In function 'rsi_dbg': drivers/net/wireless/rsi/rsi_main.h:44:20: error: function 'rsi_dbg' can never be inlined because it uses variable argument lists static inline void rsi_dbg(u32 zone, const char *fmt, ...) Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rsi: Add RS9113 wireless driverFariya Fatima2014-03-171-0/+232
This patch adds the Redpine Signals' 91x wireless driver. Signed-off-by: Fariya Fatima <fariyaf@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3-55-g7522 (git 2.39.0) at 2024-07-04 17:10:10 +0200