| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
| |
Optional fields are set to -1 by various preprocessor macros. Make
sure the fields can actually store them.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
| |
Some of the pinmux configuration bits that exist in "drive group"
registers in Tegra30..Tegra124 move to the "pinmux" registers on future
chips. Add a flag to support this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
| |
The kerneldoc for struct tegra_pingroup didn't describe all of the fields
in the struct. Add some extra kerneldoc to fix that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
| |
The range of npins and function ID values is small enough to fit into a
u8. Use this type rather than unsigned to shrink the pinmux data tables.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The fsafe value in the pingroup data tables is only used to implement
tegra_pinctrl_disable(). The only reason this function is called is when
dynamically switching between pinmux states, i.e. when disabling the old
state before programming the new state. It's simpler to have the new
target state define the expected value of each pin (and all current DTs
do that). This also gives more flexibility, since it allows individual
boards explicit control over the "inactive" mux function for each pin,
rather than requiring it to be an SoC-specific value. Assuming this, we
can get rid of the fsafe value from the driver completely, thus saving
some more space in the driver tables.
While re-writing the content of tegra124_pingroups[], fix the indentation
to use a TAB instead of spaces.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Any SoC which supports the einput, odrain, lock, ioreset, or rcv_sel
options has the relevant HW register fields in the same register as the
mux function selection. Similarly, the drvtype option is always in the
drive register, if it is supported at all. Hence, we don't need to have
struct *_reg fields in the pin group table to define which register and
bank to use for those options. Delete this to save space in the driver's
data tables.
However, many of those options are not supported on all SoCs, or not
supported on some pingroups. We need a way to detect when they are
supported. Previously, this was indicated by setting the struct *_reg
field to -1. With the struct *_reg fields removed, we use the struct
*_bit fields for this purpose instead. The struct *_bit fields need to
be expanded from 5 to 6 bits in order to store a value outside the valid
HW bit range of 0..31.
Even without removing the struct *_reg fields, we still need to add code
to validate the struct *_bit fields, since some struct *_bit fields were
already being set to -1, without an option-specific struct *_reg field to
"guard" them. In other words, before this change, the pinmux driver might
allow some unsupported options to be written to HW.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
The per-SoC data structures for Tegra pinctrl stored some information
in a redundant way. Specifically, the list of groups that each function
could be muxed onto was stored once explicitly, and also as part of the
definition of each group. Eliminate this redundancy, and calculate each
function's list of valid groups at pinctrl probe time. This removes
thousands of lines of code from the pinctrl driver and ~16K from the
vmlinux binary size, and adds only about 500uS to the boot process (on
Tegra30; newer SoCs will likely be faster still).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
NVIDIA's Tegra114 added two more configuration parameter in pinmux i.e.
rcv-sel and drive type.
rcv-sel: Select between High and Normal VIL/VIH receivers.
RCVR_SEL=1: High VIL/VIH
RCVR_SEL=0: Normal VIL/VIH
drv_type: Ouptput drive type:
33-50 ohm driver: 0x1
66-100ohm driver: 0x0
Add support of these parameters to be configure from DTS file.
Tegra20 and Tegra30 does not support this configuration and hence initialize their
pinmux structure with reg = -1.
Originally written by Pritesh Raithatha.
Changes by ldewangan:
- remove drvtype_width as it is always 2.
- Better describe the change.
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
| |
Now that Tegra's pinmux is configured solely from device tree, there's
no need for the pinconf types to be defined in arch/arm/mach-tegra/.
Move it into the pinctrl directory to clean up mach-tegra, as a pre-
requisite for single-zImage.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Rather than having a single tegra-pinctrl driver that determines whether
it's running on Tegra20 or Tegra30, instead have separate drivers for
each that call into utility functions to implement the majority of the
driver. This change is based on review feedback of the SPEAr pinctrl
driver, which had originally copied to Tegra driver structure.
This requires that the two drivers have unique names. Update a couple
spots in arch/arm/mach-tegra for the name change.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
This adds a driver for the Tegra pinmux, and required parameterization
data for Tegra20 and Tegra30.
The driver is initially added with driver name and device tree compatible
value that won't cause this driver to be used. A later change will switch
the pinctrl driver to use the correct values, switch the old pinmux
driver to be disabled, and update all code that uses the old pinmux APIs
to use the new pinctrl APIs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
[squashed "fix case of Tegra30's foo_groups[] arrays"]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
