| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
| |
Made changes to the Fabric Assigned Address(FAA) feature implementation.
Introduced the IOCFC state machine, which now handles the FAA logic,
IOC and BFA sub-modules enablement.
Removed un-wanted FAA enable/disable routines; FAA is enabled by default.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
- Modified the design such that each BFA sub-module will provide
the amount of DMA and KVA memory needed by it and queues the
same request to the global dma and kva info queues.
- During the memory allocation we iterate over this queue to allocate
the dma and kva memory requested by sub-modules.
- The change is needed to avoid requesting the aggregate amount of memory
needed by all the BFA sub-modules as one contiguous chunk.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- Introduced partitioning of the BFA resources.
- Added h/w queue ID in CPE messages, firmware uses h/w queue ID
from messages to pick a matching RME queue.
- Added message header to bfa_reqq_produce(). h/w queue ID is set
in the message header and firmware modules use h/w queue ID from
message header instead of from cpqe event.
- Made changes to allow using all 256 queues of Brocade-1860 asic.
Previously only a single queue per queue group was used.
- Added function tag to BFI message header. Only used by FC BFI
messages. Used to translate host tag to firmware tag. bfa_lpuid()
is changed to bfa_fn_lpu() that encodes both PCI function and port
ID in BFI message header.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- If flash controller is halted unconditionally, this results in
illegal write access to flash controller register domain. Since
flash controller registers are only accessible once s_clk is started
- added logic to check for WGN status and halt flash controller only
if it is already running.
- Added check to wait for flash controller halt to be completed before
proceeding with s_clk/l_clk initializations.
- Removed unnecessary reset logic for PMM 1T memory and moved memory
initialization after flash access enable.
- Disable Brocade-1860 asic MBOX interrupt before PLL initialization.
- Remove reset enable for S_CLK/L_CLK after both PLL initializations
are complete.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
| |
|
|
|
|
|
|
|
| |
- Updated/added data structures and definitions to support FAA protocol.
- Modified the IOC state machine to support FAA.
- Introduced FAA feature configuration - enable/disable/query.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
| |
|
|
|
|
|
|
|
| |
- Enhancements to FCPIM module.
- Introduced IO tag management to allocate/release IOs to FCPIM module
from a free IOtag pool.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- Introduce FC credit recovery.
- Added module parameter to enable/disable credit recovery.
Bug Fixes:
- Removed check for ignoring plogi from initiator in switched fabric mode.
- The ABTS for PLOGI is going out few millisecs earlier due to FW
timer calibration (around 300 miilisecs earlier). So there is a
window if an accept comes during this time HBA would have initiated
an ABORT.
- Added 1 to FC_ELS_TOV for compensating for FW timer.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
| |
|
|
|
|
|
|
| |
Made changes to FCS lport, vport state machines to support vport
enable / disable operations.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- Added support for Brocade-1860 Fabric Adapter.
- Made changes to support single firmware image per asic type.
- Combined bfi_cbreg.h and bfi_ctreg.h defines into bfi_reg.h with
only minimal defines used by host.
- Added changes to setup CPE/RME Queue register offsets based on
firmware response.
- Removed queue register offset initializations and added register offsets
to BFI config response message.
- Added Brocade-1860 asic specific interrupt status definitions and
mailbox interfaces.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
| |
|
|
|
|
|
|
| |
- Add PBC port Disabled condition check.
- Rename incorrectly named LPS I2H messages.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
- Avoid the use of hardware defined structure bfi_sge_s for DMA
requests in host.
- Defined a generic address len pair to represent a DMA memory chunk
(bfi_alen_s).
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
| |
|
|
|
|
|
|
| |
- Direct attach is not working due to the check of PID in fcxp_send request.
- Added logic to set the lps->lp_pid with the PID assigned for n2n mode.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
When the bfa driver is loaded a flogi is sent without the knowledge of
trunking configuration. This normal flogi causes the switch ports
which had trunking enabled to go to persistent offline. Solution is
to store the port configuration (which has trunking info) in the flash
for persistency. The firmware will read this configuration when the
very first fcport enable is received.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
|
|
|
|
|
|
| |
Remove SCSI IO callbacks, and as a result remove bfa_cb_ioim.h.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
|
|
|
|
|
| |
First round of fix for the endianess check warnings from make C=2 CF="-D__CHECK_ENDIAN__".
Signed-off-by: Maggie <xmzhang@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
|
|
|
|
|
|
|
|
| |
This patch addresses the comments from Randy Dunlap (Randy.Dunlap@oracle.com)
regarding comment blocks that begining with "/**". bfa driver comments
currently do not follow kernel-doc convention, we hence replace all
/** with /* and **/ with */.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
We have flattened the BFA hierarchy and also reduced the number of
source and header files we used to have earlier.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
