From 94d66714739242d5f6f7410bf044239e33226073 Mon Sep 17 00:00:00 2001 From: Matthias Kaehlcke Date: Wed, 27 Feb 2019 15:52:23 -0800 Subject: Bluetooth: hci_qca: Reduce delay after sending baudrate request for WCN3990 The current 300ms delay after a baudrate change is extremely long. For WCN3990 it is sufficient to wait 10ms after the baudrate change request has been sent over the wire. Signed-off-by: Matthias Kaehlcke Signed-off-by: Marcel Holtmann --- drivers/bluetooth/hci_qca.c | 26 ++++++++++++++++++-------- 1 file changed, 18 insertions(+), 8 deletions(-) (limited to 'drivers/bluetooth/hci_qca.c') diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c index 82f6cec4f71e..237aea34b69f 100644 --- a/drivers/bluetooth/hci_qca.c +++ b/drivers/bluetooth/hci_qca.c @@ -59,8 +59,7 @@ #define IBS_WAKE_RETRANS_TIMEOUT_MS 100 #define IBS_TX_IDLE_TIMEOUT_MS 2000 -#define BAUDRATE_SETTLE_TIMEOUT_MS 300 -#define POWER_PULSE_TRANS_TIMEOUT_MS 100 +#define CMD_TRANS_TIMEOUT_MS 100 /* susclk rate */ #define SUSCLK_RATE_32KHZ 32768 @@ -964,6 +963,7 @@ static int qca_set_baudrate(struct hci_dev *hdev, uint8_t baudrate) { struct hci_uart *hu = hci_get_drvdata(hdev); struct qca_data *qca = hu->priv; + struct qca_serdev *qcadev; struct sk_buff *skb; u8 cmd[] = { 0x01, 0x48, 0xFC, 0x01, 0x00 }; @@ -985,11 +985,21 @@ static int qca_set_baudrate(struct hci_dev *hdev, uint8_t baudrate) skb_queue_tail(&qca->txq, skb); hci_uart_tx_wakeup(hu); - /* wait 300ms to change new baudrate on controller side - * controller will come back after they receive this HCI command - * then host can communicate with new baudrate to controller - */ - msleep(BAUDRATE_SETTLE_TIMEOUT_MS); + qcadev = serdev_device_get_drvdata(hu->serdev); + + /* Wait for the baudrate change request to be sent */ + + while (!skb_queue_empty(&qca->txq)) + usleep_range(100, 200); + + serdev_device_wait_until_sent(hu->serdev, + msecs_to_jiffies(CMD_TRANS_TIMEOUT_MS)); + + /* Give the controller time to process the request */ + if (qcadev->btsoc_type == QCA_WCN3990) + msleep(10); + else + msleep(300); return 0; } @@ -1005,7 +1015,7 @@ static inline void host_set_baudrate(struct hci_uart *hu, unsigned int speed) static int qca_send_power_pulse(struct hci_uart *hu, bool on) { int ret; - int timeout = msecs_to_jiffies(POWER_PULSE_TRANS_TIMEOUT_MS); + int timeout = msecs_to_jiffies(CMD_TRANS_TIMEOUT_MS); u8 cmd = on ? QCA_WCN3990_POWERON_PULSE : QCA_WCN3990_POWEROFF_PULSE; /* These power pulses are single byte command which are sent -- cgit v1.2.3-55-g7522