From 2d079c43bc5ade7b41610b356bf117e14037a584 Mon Sep 17 00:00:00 2001 From: Johan Rudholm Date: Thu, 6 Nov 2014 14:46:54 +0100 Subject: mmc: core: consistent handling of initial values mmc_do_hw_reset(), mmc_power_up() and mmc_power_off() all set similar initial values for bus_mode, bus_width, chip_select and timing. Let's make this handling simpler and more consistent by sticking them together in a common function. This will introduce small changes in behavior in the following places: mmc_power_off(): For SPI hosts, explicitly set bus_mode = MMC_BUSMODE_PUSHPULL and chip_select = MMC_CS_HIGH, before we left them as they were. For non-SPI hosts, set bus_mode = MMC_BUSMODE_PUSHPULL instead of MMC_BUSMODE_OPENDRAIN as before. These two changes should not be a problem since the device will be powered off anyway. mmc_do_hw_reset(): Always set bus_mode = MMC_BUSMODE_PUSHPULL, as required by SD/SDIO cards. MMC cards require MMC_BUSMODE_OPENDRAIN, but this is taken care of by mmc_init_card() and mmc_attach_mmc(). Signed-off-by: Johan Rudholm Signed-off-by: Ulf Hansson --- drivers/mmc/core/core.c | 47 ++++++++++++++++++++++------------------------- 1 file changed, 22 insertions(+), 25 deletions(-) (limited to 'drivers/mmc/core/core.c') diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c index a32bea23e70c..5bda29bff8eb 100644 --- a/drivers/mmc/core/core.c +++ b/drivers/mmc/core/core.c @@ -1099,6 +1099,22 @@ void mmc_set_bus_width(struct mmc_host *host, unsigned int width) mmc_host_clk_release(host); } +/* + * Set initial state after a power cycle or a hw_reset. + */ +void mmc_set_initial_state(struct mmc_host *host) +{ + if (mmc_host_is_spi(host)) + host->ios.chip_select = MMC_CS_HIGH; + else + host->ios.chip_select = MMC_CS_DONTCARE; + host->ios.bus_mode = MMC_BUSMODE_PUSHPULL; + host->ios.bus_width = MMC_BUS_WIDTH_1; + host->ios.timing = MMC_TIMING_LEGACY; + + mmc_set_ios(host); +} + /** * mmc_vdd_to_ocrbitnum - Convert a voltage to the OCR bit number * @vdd: voltage (mV) @@ -1537,15 +1553,9 @@ void mmc_power_up(struct mmc_host *host, u32 ocr) mmc_host_clk_hold(host); host->ios.vdd = fls(ocr) - 1; - if (mmc_host_is_spi(host)) - host->ios.chip_select = MMC_CS_HIGH; - else - host->ios.chip_select = MMC_CS_DONTCARE; - host->ios.bus_mode = MMC_BUSMODE_PUSHPULL; host->ios.power_mode = MMC_POWER_UP; - host->ios.bus_width = MMC_BUS_WIDTH_1; - host->ios.timing = MMC_TIMING_LEGACY; - mmc_set_ios(host); + /* Set initial state and call mmc_set_ios */ + mmc_set_initial_state(host); /* Try to set signal voltage to 3.3V but fall back to 1.8v or 1.2v */ if (__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330) == 0) @@ -1585,14 +1595,9 @@ void mmc_power_off(struct mmc_host *host) host->ios.clock = 0; host->ios.vdd = 0; - if (!mmc_host_is_spi(host)) { - host->ios.bus_mode = MMC_BUSMODE_OPENDRAIN; - host->ios.chip_select = MMC_CS_DONTCARE; - } host->ios.power_mode = MMC_POWER_OFF; - host->ios.bus_width = MMC_BUS_WIDTH_1; - host->ios.timing = MMC_TIMING_LEGACY; - mmc_set_ios(host); + /* Set initial state and call mmc_set_ios */ + mmc_set_initial_state(host); /* * Some configurations, such as the 802.11 SDIO card in the OLPC @@ -2278,16 +2283,8 @@ static int mmc_do_hw_reset(struct mmc_host *host, int check) } } - if (mmc_host_is_spi(host)) { - host->ios.chip_select = MMC_CS_HIGH; - host->ios.bus_mode = MMC_BUSMODE_PUSHPULL; - } else { - host->ios.chip_select = MMC_CS_DONTCARE; - host->ios.bus_mode = MMC_BUSMODE_OPENDRAIN; - } - host->ios.bus_width = MMC_BUS_WIDTH_1; - host->ios.timing = MMC_TIMING_LEGACY; - mmc_set_ios(host); + /* Set initial state and call mmc_set_ios */ + mmc_set_initial_state(host); mmc_host_clk_release(host); -- cgit v1.2.3-55-g7522