From fbd29a14af42d374ddce9c16ff5f7805e69c764f Mon Sep 17 00:00:00 2001
From: Sebastian Andrzej Siewior
Date: Fri, 19 Nov 2010 09:00:11 -0800
Subject: spi/pxa2xx: register driver properly

use platform_driver_register instead of platform_driver_probe. The
latter only checks available devices at the time of calling. So if a
device gets inserter at a later point in time then the driver will never
play with it.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
---
 drivers/spi/pxa2xx_spi.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

(limited to 'drivers')

diff --git a/drivers/spi/pxa2xx_spi.c b/drivers/spi/pxa2xx_spi.c
index e76b1afafe07..4e169b579efb 100644
--- a/drivers/spi/pxa2xx_spi.c
+++ b/drivers/spi/pxa2xx_spi.c
@@ -1366,7 +1366,7 @@ static void cleanup(struct spi_device *spi)
 	kfree(chip);
 }
 
-static int __init init_queue(struct driver_data *drv_data)
+static int __devinit init_queue(struct driver_data *drv_data)
 {
 	INIT_LIST_HEAD(&drv_data->queue);
 	spin_lock_init(&drv_data->lock);
@@ -1454,7 +1454,7 @@ static int destroy_queue(struct driver_data *drv_data)
 	return 0;
 }
 
-static int __init pxa2xx_spi_probe(struct platform_device *pdev)
+static int __devinit pxa2xx_spi_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct pxa2xx_spi_master *platform_info;
@@ -1723,13 +1723,14 @@ static struct platform_driver driver = {
 		.pm	= &pxa2xx_spi_pm_ops,
 #endif
 	},
+	.probe = pxa2xx_spi_probe,
 	.remove = pxa2xx_spi_remove,
 	.shutdown = pxa2xx_spi_shutdown,
 };
 
 static int __init pxa2xx_spi_init(void)
 {
-	return platform_driver_probe(&driver, pxa2xx_spi_probe);
+	return platform_driver_register(&driver);
 }
 subsys_initcall(pxa2xx_spi_init);
 
-- 
cgit v1.2.3-55-g7522


From 49cbb1e0b6dcba9170e72fdf40c75fc24cadba4b Mon Sep 17 00:00:00 2001
From: Sebastian Andrzej Siewior
Date: Mon, 22 Nov 2010 17:12:14 -0800
Subject: spi/pxa2xx: add support for shared IRQ handler

This is required in case the interrupt line is shared with other
devices.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
---
 drivers/spi/pxa2xx_spi.c | 15 ++++++++++++++-
 1 file changed, 14 insertions(+), 1 deletion(-)

(limited to 'drivers')

diff --git a/drivers/spi/pxa2xx_spi.c b/drivers/spi/pxa2xx_spi.c
index 4e169b579efb..1865c23f2175 100644
--- a/drivers/spi/pxa2xx_spi.c
+++ b/drivers/spi/pxa2xx_spi.c
@@ -742,6 +742,18 @@ static irqreturn_t ssp_int(int irq, void *dev_id)
 {
 	struct driver_data *drv_data = dev_id;
 	void __iomem *reg = drv_data->ioaddr;
+	u32 sccr1_reg = read_SSCR1(reg);
+	u32 mask = drv_data->mask_sr;
+	u32 status;
+
+	status = read_SSSR(reg);
+
+	/* Ignore possible writes if we don't need to write */
+	if (!(sccr1_reg & SSCR1_TIE))
+		mask &= ~SSSR_TFS;
+
+	if (!(status & mask))
+		return IRQ_NONE;
 
 	if (!drv_data->cur_msg) {
 
@@ -1512,7 +1524,8 @@ static int __devinit pxa2xx_spi_probe(struct platform_device *pdev)
 		drv_data->mask_sr = SSSR_TINT | SSSR_RFS | SSSR_TFS | SSSR_ROR;
 	}
 
-	status = request_irq(ssp->irq, ssp_int, 0, dev_name(dev), drv_data);
+	status = request_irq(ssp->irq, ssp_int, IRQF_SHARED, dev_name(dev),
+			drv_data);
 	if (status < 0) {
 		dev_err(&pdev->dev, "cannot get IRQ %d\n", ssp->irq);
 		goto out_error_master_alloc;
-- 
cgit v1.2.3-55-g7522


From 4a25605fb71f02b4f80091df91f777225a0309c5 Mon Sep 17 00:00:00 2001
From: Sebastian Andrzej Siewior
Date: Mon, 22 Nov 2010 17:12:15 -0800
Subject: spi/pxa2xx: Use define for SSSR_TFL_MASK instead of plain numbers

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
---
 arch/arm/plat-pxa/include/plat/ssp.h | 3 ++-
 drivers/spi/pxa2xx_spi.c             | 8 ++++----
 2 files changed, 6 insertions(+), 5 deletions(-)

(limited to 'drivers')

diff --git a/arch/arm/plat-pxa/include/plat/ssp.h b/arch/arm/plat-pxa/include/plat/ssp.h
index fe43150690ed..21c12ca80738 100644
--- a/arch/arm/plat-pxa/include/plat/ssp.h
+++ b/arch/arm/plat-pxa/include/plat/ssp.h
@@ -82,7 +82,8 @@
 #define SSSR_TFS	(1 << 5)	/* Transmit FIFO Service Request */
 #define SSSR_RFS	(1 << 6)	/* Receive FIFO Service Request */
 #define SSSR_ROR	(1 << 7)	/* Receive FIFO Overrun */
-
+#define SSSR_TFL_MASK   (0xf << 8)	/* Transmit FIFO Level mask */
+#define SSSR_RFL_MASK   (0xf << 12)	/* Receive FIFO Level mask */
 
 /* extra bits in PXA255, PXA26x and PXA27x SSP ports */
 #define SSCR0_TISSP		(1 << 4)	/* TI Sync Serial Protocol */
diff --git a/drivers/spi/pxa2xx_spi.c b/drivers/spi/pxa2xx_spi.c
index 1865c23f2175..55083445aae6 100644
--- a/drivers/spi/pxa2xx_spi.c
+++ b/drivers/spi/pxa2xx_spi.c
@@ -224,7 +224,7 @@ static int null_writer(struct driver_data *drv_data)
 	void __iomem *reg = drv_data->ioaddr;
 	u8 n_bytes = drv_data->n_bytes;
 
-	if (((read_SSSR(reg) & 0x00000f00) == 0x00000f00)
+	if (((read_SSSR(reg) & SSSR_TFL_MASK) == SSSR_TFL_MASK)
 		|| (drv_data->tx == drv_data->tx_end))
 		return 0;
 
@@ -252,7 +252,7 @@ static int u8_writer(struct driver_data *drv_data)
 {
 	void __iomem *reg = drv_data->ioaddr;
 
-	if (((read_SSSR(reg) & 0x00000f00) == 0x00000f00)
+	if (((read_SSSR(reg) & SSSR_TFL_MASK) == SSSR_TFL_MASK)
 		|| (drv_data->tx == drv_data->tx_end))
 		return 0;
 
@@ -279,7 +279,7 @@ static int u16_writer(struct driver_data *drv_data)
 {
 	void __iomem *reg = drv_data->ioaddr;
 
-	if (((read_SSSR(reg) & 0x00000f00) == 0x00000f00)
+	if (((read_SSSR(reg) & SSSR_TFL_MASK) == SSSR_TFL_MASK)
 		|| (drv_data->tx == drv_data->tx_end))
 		return 0;
 
@@ -306,7 +306,7 @@ static int u32_writer(struct driver_data *drv_data)
 {
 	void __iomem *reg = drv_data->ioaddr;
 
-	if (((read_SSSR(reg) & 0x00000f00) == 0x00000f00)
+	if (((read_SSSR(reg) & SSSR_TFL_MASK) == SSSR_TFL_MASK)
 		|| (drv_data->tx == drv_data->tx_end))
 		return 0;
 
-- 
cgit v1.2.3-55-g7522


From 8348c259dd6a6019a8fa01b0a3443409480f7b9d Mon Sep 17 00:00:00 2001
From: Sebastian Andrzej Siewior
Date: Mon, 22 Nov 2010 17:12:15 -0800
Subject: arm/pxa2xx: reorgazine SSP and SPI header files

The PXA-SPI driver relies on some files / defines which are arm specific
and are within the ARM tree. The CE4100 SoC which is x86 has also the
SPI core.
This patch moves the ssp and spi files from arm/mach-pxa and plat-pxa to
include/linux where the CE4100 can access them.

This move got verified by building the following defconfigs:
   cm_x2xx_defconfig corgi_defconfig em_x270_defconfig ezx_defconfig
   imote2_defconfig pxa3xx_defconfig spitz_defconfig zeus_defconfig
   raumfeld_defconfig magician_defconfig

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
---
 Documentation/spi/pxa2xx                    |   4 +-
 arch/arm/mach-pxa/cm-x255.c                 |   2 +-
 arch/arm/mach-pxa/cm-x270.c                 |   2 +-
 arch/arm/mach-pxa/corgi.c                   |   2 +-
 arch/arm/mach-pxa/devices.c                 |   2 +-
 arch/arm/mach-pxa/em-x270.c                 |   2 +-
 arch/arm/mach-pxa/hx4700.c                  |   2 +-
 arch/arm/mach-pxa/icontrol.c                |   2 +-
 arch/arm/mach-pxa/include/mach/pxa2xx_spi.h |  47 -------
 arch/arm/mach-pxa/littleton.c               |   2 +-
 arch/arm/mach-pxa/lubbock.c                 |   2 +-
 arch/arm/mach-pxa/pcm027.c                  |   2 +-
 arch/arm/mach-pxa/poodle.c                  |   2 +-
 arch/arm/mach-pxa/spitz.c                   |   3 +-
 arch/arm/mach-pxa/stargate2.c               |   2 +-
 arch/arm/mach-pxa/tosa.c                    |   2 +-
 arch/arm/mach-pxa/trizeps4.c                |   1 -
 arch/arm/mach-pxa/z2.c                      |   2 +-
 arch/arm/mach-pxa/zeus.c                    |   2 +-
 arch/arm/plat-pxa/include/plat/ssp.h        | 187 ----------------------------
 arch/arm/plat-pxa/ssp.c                     |   2 +-
 drivers/spi/pxa2xx_spi.c                    |   4 +-
 include/linux/pxa2xx_ssp.h                  | 187 ++++++++++++++++++++++++++++
 include/linux/spi/pxa2xx_spi.h              |  49 ++++++++
 sound/soc/pxa/pxa-ssp.c                     |   2 +-
 25 files changed, 257 insertions(+), 259 deletions(-)
 delete mode 100644 arch/arm/mach-pxa/include/mach/pxa2xx_spi.h
 delete mode 100644 arch/arm/plat-pxa/include/plat/ssp.h
 create mode 100644 include/linux/pxa2xx_ssp.h
 create mode 100644 include/linux/spi/pxa2xx_spi.h

(limited to 'drivers')

diff --git a/Documentation/spi/pxa2xx b/Documentation/spi/pxa2xx
index 6bb916d57c95..68a4fe3818a1 100644
--- a/Documentation/spi/pxa2xx
+++ b/Documentation/spi/pxa2xx
@@ -19,7 +19,7 @@ Declaring PXA2xx Master Controllers
 -----------------------------------
 Typically a SPI master is defined in the arch/.../mach-*/board-*.c as a
 "platform device".  The master configuration is passed to the driver via a table
-found in arch/arm/mach-pxa/include/mach/pxa2xx_spi.h:
+found in include/linux/spi/pxa2xx_spi.h:
 
 struct pxa2xx_spi_master {
 	enum pxa_ssp_type ssp_type;
@@ -94,7 +94,7 @@ using the "spi_board_info" structure found in "linux/spi/spi.h". See
 
 Each slave device attached to the PXA must provide slave specific configuration
 information via the structure "pxa2xx_spi_chip" found in
-"arch/arm/mach-pxa/include/mach/pxa2xx_spi.h".  The pxa2xx_spi master controller driver
+"include/linux/spi/pxa2xx_spi.h".  The pxa2xx_spi master controller driver
 will uses the configuration whenever the driver communicates with the slave
 device. All fields are optional.
 
diff --git a/arch/arm/mach-pxa/cm-x255.c b/arch/arm/mach-pxa/cm-x255.c
index f1a7703d771b..93f59f877fc6 100644
--- a/arch/arm/mach-pxa/cm-x255.c
+++ b/arch/arm/mach-pxa/cm-x255.c
@@ -17,13 +17,13 @@
 #include <linux/mtd/nand-gpio.h>
 
 #include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
 #include <asm/mach/map.h>
 
 #include <mach/pxa25x.h>
-#include <mach/pxa2xx_spi.h>
 
 #include "generic.h"
 
diff --git a/arch/arm/mach-pxa/cm-x270.c b/arch/arm/mach-pxa/cm-x270.c
index a9926bb75922..b88d601a8090 100644
--- a/arch/arm/mach-pxa/cm-x270.c
+++ b/arch/arm/mach-pxa/cm-x270.c
@@ -19,12 +19,12 @@
 #include <video/mbxfb.h>
 
 #include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
 #include <linux/spi/libertas_spi.h>
 
 #include <mach/pxa27x.h>
 #include <mach/ohci.h>
 #include <mach/mmc.h>
-#include <mach/pxa2xx_spi.h>
 
 #include "generic.h"
 
diff --git a/arch/arm/mach-pxa/corgi.c b/arch/arm/mach-pxa/corgi.c
index 821229acabe6..3b8dcac2b8fb 100644
--- a/arch/arm/mach-pxa/corgi.c
+++ b/arch/arm/mach-pxa/corgi.c
@@ -28,6 +28,7 @@
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
 #include <linux/spi/corgi_lcd.h>
+#include <linux/spi/pxa2xx_spi.h>
 #include <linux/mtd/sharpsl.h>
 #include <linux/input/matrix_keypad.h>
 #include <video/w100fb.h>
@@ -48,7 +49,6 @@
 #include <mach/irda.h>
 #include <mach/mmc.h>
 #include <mach/udc.h>
-#include <mach/pxa2xx_spi.h>
 #include <mach/corgi.h>
 #include <mach/sharpsl_pm.h>
 
diff --git a/arch/arm/mach-pxa/devices.c b/arch/arm/mach-pxa/devices.c
index aaa1166df964..c4f9c715be73 100644
--- a/arch/arm/mach-pxa/devices.c
+++ b/arch/arm/mach-pxa/devices.c
@@ -3,6 +3,7 @@
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/dma-mapping.h>
+#include <linux/spi/pxa2xx_spi.h>
 
 #include <asm/pmu.h>
 #include <mach/udc.h>
@@ -12,7 +13,6 @@
 #include <mach/irda.h>
 #include <mach/ohci.h>
 #include <plat/pxa27x_keypad.h>
-#include <mach/pxa2xx_spi.h>
 #include <mach/camera.h>
 #include <mach/audio.h>
 #include <mach/hardware.h>
diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c
index ed0dbfdb22ed..b20b944c337c 100644
--- a/arch/arm/mach-pxa/em-x270.c
+++ b/arch/arm/mach-pxa/em-x270.c
@@ -26,6 +26,7 @@
 #include <linux/spi/spi.h>
 #include <linux/spi/tdo24m.h>
 #include <linux/spi/libertas_spi.h>
+#include <linux/spi/pxa2xx_spi.h>
 #include <linux/power_supply.h>
 #include <linux/apm-emulation.h>
 #include <linux/i2c.h>
@@ -46,7 +47,6 @@
 #include <plat/pxa27x_keypad.h>
 #include <plat/i2c.h>
 #include <mach/camera.h>
-#include <mach/pxa2xx_spi.h>
 
 #include "generic.h"
 #include "devices.h"
diff --git a/arch/arm/mach-pxa/hx4700.c b/arch/arm/mach-pxa/hx4700.c
index 76d93a25bab6..f09526f52152 100644
--- a/arch/arm/mach-pxa/hx4700.c
+++ b/arch/arm/mach-pxa/hx4700.c
@@ -33,6 +33,7 @@
 #include <linux/regulator/max1586.h>
 #include <linux/spi/ads7846.h>
 #include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
 #include <linux/usb/gpio_vbus.h>
 
 #include <mach/hardware.h>
@@ -43,7 +44,6 @@
 #include <mach/hx4700.h>
 #include <plat/i2c.h>
 #include <mach/irda.h>
-#include <mach/pxa2xx_spi.h>
 
 #include <video/platform_lcd.h>
 #include <video/w100fb.h>
diff --git a/arch/arm/mach-pxa/icontrol.c b/arch/arm/mach-pxa/icontrol.c
index d51ee3d25e70..3ab6fd369584 100644
--- a/arch/arm/mach-pxa/icontrol.c
+++ b/arch/arm/mach-pxa/icontrol.c
@@ -24,7 +24,7 @@
 #include <mach/mxm8x10.h>
 
 #include <linux/spi/spi.h>
-#include <mach/pxa2xx_spi.h>
+#include <linux/spi/pxa2xx_spi.h>
 #include <linux/can/platform/mcp251x.h>
 
 #include "generic.h"
diff --git a/arch/arm/mach-pxa/include/mach/pxa2xx_spi.h b/arch/arm/mach-pxa/include/mach/pxa2xx_spi.h
deleted file mode 100644
index b87cecd9bbdc..000000000000
--- a/arch/arm/mach-pxa/include/mach/pxa2xx_spi.h
+++ /dev/null
@@ -1,47 +0,0 @@
-/*
- * Copyright (C) 2005 Stephen Street / StreetFire Sound Labs
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#ifndef PXA2XX_SPI_H_
-#define PXA2XX_SPI_H_
-
-#define PXA2XX_CS_ASSERT (0x01)
-#define PXA2XX_CS_DEASSERT (0x02)
-
-/* device.platform_data for SSP controller devices */
-struct pxa2xx_spi_master {
-	u32 clock_enable;
-	u16 num_chipselect;
-	u8 enable_dma;
-};
-
-/* spi_board_info.controller_data for SPI slave devices,
- * copied to spi_device.platform_data ... mostly for dma tuning
- */
-struct pxa2xx_spi_chip {
-	u8 tx_threshold;
-	u8 rx_threshold;
-	u8 dma_burst_size;
-	u32 timeout;
-	u8 enable_loopback;
-	int gpio_cs;
-	void (*cs_control)(u32 command);
-};
-
-extern void pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_master *info);
-
-#endif /*PXA2XX_SPI_H_*/
diff --git a/arch/arm/mach-pxa/littleton.c b/arch/arm/mach-pxa/littleton.c
index 41aa89e35772..8051925d457c 100644
--- a/arch/arm/mach-pxa/littleton.c
+++ b/arch/arm/mach-pxa/littleton.c
@@ -22,6 +22,7 @@
 #include <linux/clk.h>
 #include <linux/gpio.h>
 #include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
 #include <linux/smc91x.h>
 #include <linux/i2c.h>
 #include <linux/leds.h>
@@ -42,7 +43,6 @@
 #include <mach/pxa300.h>
 #include <mach/pxafb.h>
 #include <mach/mmc.h>
-#include <mach/pxa2xx_spi.h>
 #include <plat/pxa27x_keypad.h>
 #include <mach/littleton.h>
 #include <plat/i2c.h>
diff --git a/arch/arm/mach-pxa/lubbock.c b/arch/arm/mach-pxa/lubbock.c
index 1499493cd070..4a3fe450c20f 100644
--- a/arch/arm/mach-pxa/lubbock.c
+++ b/arch/arm/mach-pxa/lubbock.c
@@ -25,7 +25,7 @@
 
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
-#include <mach/pxa2xx_spi.h>
+#include <linux/spi/pxa2xx_spi.h>
 
 #include <asm/setup.h>
 #include <asm/memory.h>
diff --git a/arch/arm/mach-pxa/pcm027.c b/arch/arm/mach-pxa/pcm027.c
index c77e8f30a439..a5596f9b17bc 100644
--- a/arch/arm/mach-pxa/pcm027.c
+++ b/arch/arm/mach-pxa/pcm027.c
@@ -25,12 +25,12 @@
 #include <linux/mtd/physmap.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/max7301.h>
+#include <linux/spi/pxa2xx_spi.h>
 #include <linux/leds.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <mach/pxa27x.h>
-#include <mach/pxa2xx_spi.h>
 #include <mach/pcm027.h>
 #include "generic.h"
 
diff --git a/arch/arm/mach-pxa/poodle.c b/arch/arm/mach-pxa/poodle.c
index 93a191c889df..c05eee326234 100644
--- a/arch/arm/mach-pxa/poodle.c
+++ b/arch/arm/mach-pxa/poodle.c
@@ -25,6 +25,7 @@
 #include <linux/i2c.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
+#include <linux/spi/pxa2xx_spi.h>
 #include <linux/mtd/sharpsl.h>
 
 #include <mach/hardware.h>
@@ -43,7 +44,6 @@
 #include <mach/irda.h>
 #include <mach/poodle.h>
 #include <mach/pxafb.h>
-#include <mach/pxa2xx_spi.h>
 #include <plat/i2c.h>
 
 #include <asm/hardware/scoop.h>
diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index f736119f1ebf..4fd5572f6995 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -23,7 +23,7 @@
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
 #include <linux/spi/corgi_lcd.h>
-#include <linux/mtd/physmap.h>
+#include <linux/spi/pxa2xx_spi.h>
 #include <linux/mtd/sharpsl.h>
 #include <linux/input/matrix_keypad.h>
 #include <linux/regulator/machine.h>
@@ -41,7 +41,6 @@
 #include <mach/mmc.h>
 #include <mach/ohci.h>
 #include <mach/pxafb.h>
-#include <mach/pxa2xx_spi.h>
 #include <mach/spitz.h>
 #include <mach/sharpsl_pm.h>
 
diff --git a/arch/arm/mach-pxa/stargate2.c b/arch/arm/mach-pxa/stargate2.c
index 738adc1773fd..325f6ac6b591 100644
--- a/arch/arm/mach-pxa/stargate2.c
+++ b/arch/arm/mach-pxa/stargate2.c
@@ -46,10 +46,10 @@
 #include <plat/i2c.h>
 #include <mach/mmc.h>
 #include <mach/udc.h>
-#include <mach/pxa2xx_spi.h>
 #include <mach/pxa27x-udc.h>
 
 #include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
 #include <linux/mfd/da903x.h>
 #include <linux/sht15.h>
 
diff --git a/arch/arm/mach-pxa/tosa.c b/arch/arm/mach-pxa/tosa.c
index 0ee1df49606d..7b5765dacbd9 100644
--- a/arch/arm/mach-pxa/tosa.c
+++ b/arch/arm/mach-pxa/tosa.c
@@ -32,6 +32,7 @@
 #include <linux/gpio.h>
 #include <linux/pda_power.h>
 #include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
 #include <linux/input/matrix_keypad.h>
 
 #include <asm/setup.h>
@@ -44,7 +45,6 @@
 #include <mach/mmc.h>
 #include <mach/udc.h>
 #include <mach/tosa_bt.h>
-#include <mach/pxa2xx_spi.h>
 #include <mach/audio.h>
 
 #include <asm/mach/arch.h>
diff --git a/arch/arm/mach-pxa/trizeps4.c b/arch/arm/mach-pxa/trizeps4.c
index 565d062f51d5..bdb02a0ae1b7 100644
--- a/arch/arm/mach-pxa/trizeps4.c
+++ b/arch/arm/mach-pxa/trizeps4.c
@@ -40,7 +40,6 @@
 #include <asm/mach/flash.h>
 
 #include <mach/pxa27x.h>
-#include <mach/pxa2xx_spi.h>
 #include <mach/trizeps4.h>
 #include <mach/audio.h>
 #include <mach/pxafb.h>
diff --git a/arch/arm/mach-pxa/z2.c b/arch/arm/mach-pxa/z2.c
index fefde9848d82..1b8b71b3c719 100644
--- a/arch/arm/mach-pxa/z2.c
+++ b/arch/arm/mach-pxa/z2.c
@@ -20,6 +20,7 @@
 #include <linux/z2_battery.h>
 #include <linux/dma-mapping.h>
 #include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
 #include <linux/spi/libertas_spi.h>
 #include <linux/spi/lms283gf05.h>
 #include <linux/power_supply.h>
@@ -38,7 +39,6 @@
 #include <mach/pxafb.h>
 #include <mach/mmc.h>
 #include <plat/pxa27x_keypad.h>
-#include <mach/pxa2xx_spi.h>
 
 #include <plat/i2c.h>
 
diff --git a/arch/arm/mach-pxa/zeus.c b/arch/arm/mach-pxa/zeus.c
index dea46a2d089b..f5c9f3032c31 100644
--- a/arch/arm/mach-pxa/zeus.c
+++ b/arch/arm/mach-pxa/zeus.c
@@ -20,6 +20,7 @@
 #include <linux/dm9000.h>
 #include <linux/mmc/host.h>
 #include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/physmap.h>
@@ -41,7 +42,6 @@
 #include <mach/pxa27x-udc.h>
 #include <mach/udc.h>
 #include <mach/pxafb.h>
-#include <mach/pxa2xx_spi.h>
 #include <mach/mfp-pxa27x.h>
 #include <mach/pm.h>
 #include <mach/audio.h>
diff --git a/arch/arm/plat-pxa/include/plat/ssp.h b/arch/arm/plat-pxa/include/plat/ssp.h
deleted file mode 100644
index 21c12ca80738..000000000000
--- a/arch/arm/plat-pxa/include/plat/ssp.h
+++ /dev/null
@@ -1,187 +0,0 @@
-/*
- *  ssp.h
- *
- *  Copyright (C) 2003 Russell King, All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This driver supports the following PXA CPU/SSP ports:-
- *
- *       PXA250     SSP
- *       PXA255     SSP, NSSP
- *       PXA26x     SSP, NSSP, ASSP
- *       PXA27x     SSP1, SSP2, SSP3
- *       PXA3xx     SSP1, SSP2, SSP3, SSP4
- */
-
-#ifndef __ASM_ARCH_SSP_H
-#define __ASM_ARCH_SSP_H
-
-#include <linux/list.h>
-#include <linux/io.h>
-
-/*
- * SSP Serial Port Registers
- * PXA250, PXA255, PXA26x and PXA27x SSP controllers are all slightly different.
- * PXA255, PXA26x and PXA27x have extra ports, registers and bits.
- */
-
-#define SSCR0		(0x00)  /* SSP Control Register 0 */
-#define SSCR1		(0x04)  /* SSP Control Register 1 */
-#define SSSR		(0x08)  /* SSP Status Register */
-#define SSITR		(0x0C)  /* SSP Interrupt Test Register */
-#define SSDR		(0x10)  /* SSP Data Write/Data Read Register */
-
-#define SSTO		(0x28)  /* SSP Time Out Register */
-#define SSPSP		(0x2C)  /* SSP Programmable Serial Protocol */
-#define SSTSA		(0x30)  /* SSP Tx Timeslot Active */
-#define SSRSA		(0x34)  /* SSP Rx Timeslot Active */
-#define SSTSS		(0x38)  /* SSP Timeslot Status */
-#define SSACD		(0x3C)  /* SSP Audio Clock Divider */
-#define SSACDD		(0x40)	/* SSP Audio Clock Dither Divider */
-
-/* Common PXA2xx bits first */
-#define SSCR0_DSS	(0x0000000f)	/* Data Size Select (mask) */
-#define SSCR0_DataSize(x)  ((x) - 1)	/* Data Size Select [4..16] */
-#define SSCR0_FRF	(0x00000030)	/* FRame Format (mask) */
-#define SSCR0_Motorola	(0x0 << 4)	/* Motorola's Serial Peripheral Interface (SPI) */
-#define SSCR0_TI	(0x1 << 4)	/* Texas Instruments' Synchronous Serial Protocol (SSP) */
-#define SSCR0_National	(0x2 << 4)	/* National Microwire */
-#define SSCR0_ECS	(1 << 6)	/* External clock select */
-#define SSCR0_SSE	(1 << 7)	/* Synchronous Serial Port Enable */
-#define SSCR0_SCR(x)	((x) << 8)	/* Serial Clock Rate (mask) */
-
-/* PXA27x, PXA3xx */
-#define SSCR0_EDSS	(1 << 20)	/* Extended data size select */
-#define SSCR0_NCS	(1 << 21)	/* Network clock select */
-#define SSCR0_RIM	(1 << 22)	/* Receive FIFO overrrun interrupt mask */
-#define SSCR0_TUM	(1 << 23)	/* Transmit FIFO underrun interrupt mask */
-#define SSCR0_FRDC	(0x07000000)	/* Frame rate divider control (mask) */
-#define SSCR0_SlotsPerFrm(x) (((x) - 1) << 24)	/* Time slots per frame [1..8] */
-#define SSCR0_FPCKE	(1 << 29)	/* FIFO packing enable */
-#define SSCR0_ACS	(1 << 30)	/* Audio clock select */
-#define SSCR0_MOD	(1 << 31)	/* Mode (normal or network) */
-
-
-#define SSCR1_RIE	(1 << 0)	/* Receive FIFO Interrupt Enable */
-#define SSCR1_TIE	(1 << 1)	/* Transmit FIFO Interrupt Enable */
-#define SSCR1_LBM	(1 << 2)	/* Loop-Back Mode */
-#define SSCR1_SPO	(1 << 3)	/* Motorola SPI SSPSCLK polarity setting */
-#define SSCR1_SPH	(1 << 4)	/* Motorola SPI SSPSCLK phase setting */
-#define SSCR1_MWDS	(1 << 5)	/* Microwire Transmit Data Size */
-#define SSCR1_TFT	(0x000003c0)	/* Transmit FIFO Threshold (mask) */
-#define SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..16] */
-#define SSCR1_RFT	(0x00003c00)	/* Receive FIFO Threshold (mask) */
-#define SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..16] */
-
-#define SSSR_TNF	(1 << 2)	/* Transmit FIFO Not Full */
-#define SSSR_RNE	(1 << 3)	/* Receive FIFO Not Empty */
-#define SSSR_BSY	(1 << 4)	/* SSP Busy */
-#define SSSR_TFS	(1 << 5)	/* Transmit FIFO Service Request */
-#define SSSR_RFS	(1 << 6)	/* Receive FIFO Service Request */
-#define SSSR_ROR	(1 << 7)	/* Receive FIFO Overrun */
-#define SSSR_TFL_MASK   (0xf << 8)	/* Transmit FIFO Level mask */
-#define SSSR_RFL_MASK   (0xf << 12)	/* Receive FIFO Level mask */
-
-/* extra bits in PXA255, PXA26x and PXA27x SSP ports */
-#define SSCR0_TISSP		(1 << 4)	/* TI Sync Serial Protocol */
-#define SSCR0_PSP		(3 << 4)	/* PSP - Programmable Serial Protocol */
-#define SSCR1_TTELP		(1 << 31)	/* TXD Tristate Enable Last Phase */
-#define SSCR1_TTE		(1 << 30)	/* TXD Tristate Enable */
-#define SSCR1_EBCEI		(1 << 29)	/* Enable Bit Count Error interrupt */
-#define SSCR1_SCFR		(1 << 28)	/* Slave Clock free Running */
-#define SSCR1_ECRA		(1 << 27)	/* Enable Clock Request A */
-#define SSCR1_ECRB		(1 << 26)	/* Enable Clock request B */
-#define SSCR1_SCLKDIR		(1 << 25)	/* Serial Bit Rate Clock Direction */
-#define SSCR1_SFRMDIR		(1 << 24)	/* Frame Direction */
-#define SSCR1_RWOT		(1 << 23)	/* Receive Without Transmit */
-#define SSCR1_TRAIL		(1 << 22)	/* Trailing Byte */
-#define SSCR1_TSRE		(1 << 21)	/* Transmit Service Request Enable */
-#define SSCR1_RSRE		(1 << 20)	/* Receive Service Request Enable */
-#define SSCR1_TINTE		(1 << 19)	/* Receiver Time-out Interrupt enable */
-#define SSCR1_PINTE		(1 << 18)	/* Peripheral Trailing Byte Interupt Enable */
-#define SSCR1_IFS		(1 << 16)	/* Invert Frame Signal */
-#define SSCR1_STRF		(1 << 15)	/* Select FIFO or EFWR */
-#define SSCR1_EFWR		(1 << 14)	/* Enable FIFO Write/Read */
-
-#define SSSR_BCE		(1 << 23)	/* Bit Count Error */
-#define SSSR_CSS		(1 << 22)	/* Clock Synchronisation Status */
-#define SSSR_TUR		(1 << 21)	/* Transmit FIFO Under Run */
-#define SSSR_EOC		(1 << 20)	/* End Of Chain */
-#define SSSR_TINT		(1 << 19)	/* Receiver Time-out Interrupt */
-#define SSSR_PINT		(1 << 18)	/* Peripheral Trailing Byte Interrupt */
-
-
-#define SSPSP_SCMODE(x)		((x) << 0)	/* Serial Bit Rate Clock Mode */
-#define SSPSP_SFRMP		(1 << 2)	/* Serial Frame Polarity */
-#define SSPSP_ETDS		(1 << 3)	/* End of Transfer data State */
-#define SSPSP_STRTDLY(x)	((x) << 4)	/* Start Delay */
-#define SSPSP_DMYSTRT(x)	((x) << 7)	/* Dummy Start */
-#define SSPSP_SFRMDLY(x)	((x) << 9)	/* Serial Frame Delay */
-#define SSPSP_SFRMWDTH(x)	((x) << 16)	/* Serial Frame Width */
-#define SSPSP_DMYSTOP(x)	((x) << 23)	/* Dummy Stop */
-#define SSPSP_FSRT		(1 << 25)	/* Frame Sync Relative Timing */
-
-/* PXA3xx */
-#define SSPSP_EDMYSTRT(x)	((x) << 26)     /* Extended Dummy Start */
-#define SSPSP_EDMYSTOP(x)	((x) << 28)     /* Extended Dummy Stop */
-#define SSPSP_TIMING_MASK	(0x7f8001f0)
-
-#define SSACD_SCDB		(1 << 3)	/* SSPSYSCLK Divider Bypass */
-#define SSACD_ACPS(x)		((x) << 4)	/* Audio clock PLL select */
-#define SSACD_ACDS(x)		((x) << 0)	/* Audio clock divider select */
-#define SSACD_SCDX8		(1 << 7)	/* SYSCLK division ratio select */
-
-enum pxa_ssp_type {
-	SSP_UNDEFINED = 0,
-	PXA25x_SSP,  /* pxa 210, 250, 255, 26x */
-	PXA25x_NSSP, /* pxa 255, 26x (including ASSP) */
-	PXA27x_SSP,
-	PXA168_SSP,
-};
-
-struct ssp_device {
-	struct platform_device *pdev;
-	struct list_head	node;
-
-	struct clk	*clk;
-	void __iomem	*mmio_base;
-	unsigned long	phys_base;
-
-	const char	*label;
-	int		port_id;
-	int		type;
-	int		use_count;
-	int		irq;
-	int		drcmr_rx;
-	int		drcmr_tx;
-};
-
-/**
- * pxa_ssp_write_reg - Write to a SSP register
- *
- * @dev: SSP device to access
- * @reg: Register to write to
- * @val: Value to be written.
- */
-static inline void pxa_ssp_write_reg(struct ssp_device *dev, u32 reg, u32 val)
-{
-	__raw_writel(val, dev->mmio_base + reg);
-}
-
-/**
- * pxa_ssp_read_reg - Read from a SSP register
- *
- * @dev: SSP device to access
- * @reg: Register to read from
- */
-static inline u32 pxa_ssp_read_reg(struct ssp_device *dev, u32 reg)
-{
-	return __raw_readl(dev->mmio_base + reg);
-}
-
-struct ssp_device *pxa_ssp_request(int port, const char *label);
-void pxa_ssp_free(struct ssp_device *);
-#endif /* __ASM_ARCH_SSP_H */
diff --git a/arch/arm/plat-pxa/ssp.c b/arch/arm/plat-pxa/ssp.c
index c6357e554aba..58b79809d20c 100644
--- a/arch/arm/plat-pxa/ssp.c
+++ b/arch/arm/plat-pxa/ssp.c
@@ -28,11 +28,11 @@
 #include <linux/clk.h>
 #include <linux/err.h>
 #include <linux/platform_device.h>
+#include <linux/spi/pxa2xx_spi.h>
 #include <linux/io.h>
 
 #include <asm/irq.h>
 #include <mach/hardware.h>
-#include <plat/ssp.h>
 
 static DEFINE_MUTEX(ssp_lock);
 static LIST_HEAD(ssp_list);
diff --git a/drivers/spi/pxa2xx_spi.c b/drivers/spi/pxa2xx_spi.c
index 55083445aae6..98d9c8b09182 100644
--- a/drivers/spi/pxa2xx_spi.c
+++ b/drivers/spi/pxa2xx_spi.c
@@ -23,6 +23,7 @@
 #include <linux/errno.h>
 #include <linux/interrupt.h>
 #include <linux/platform_device.h>
+#include <linux/spi/pxa2xx_spi.h>
 #include <linux/dma-mapping.h>
 #include <linux/spi/spi.h>
 #include <linux/workqueue.h>
@@ -35,9 +36,6 @@
 #include <asm/irq.h>
 #include <asm/delay.h>
 
-#include <mach/dma.h>
-#include <plat/ssp.h>
-#include <mach/pxa2xx_spi.h>
 
 MODULE_AUTHOR("Stephen Street");
 MODULE_DESCRIPTION("PXA2xx SSP SPI Controller");
diff --git a/include/linux/pxa2xx_ssp.h b/include/linux/pxa2xx_ssp.h
new file mode 100644
index 000000000000..84465d4a51b7
--- /dev/null
+++ b/include/linux/pxa2xx_ssp.h
@@ -0,0 +1,187 @@
+/*
+ *  pxa2xx_ssp.h
+ *
+ *  Copyright (C) 2003 Russell King, All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This driver supports the following PXA CPU/SSP ports:-
+ *
+ *       PXA250     SSP
+ *       PXA255     SSP, NSSP
+ *       PXA26x     SSP, NSSP, ASSP
+ *       PXA27x     SSP1, SSP2, SSP3
+ *       PXA3xx     SSP1, SSP2, SSP3, SSP4
+ */
+
+#ifndef __LINUX_SSP_H
+#define __LINUX_SSP_H
+
+#include <linux/list.h>
+#include <linux/io.h>
+
+/*
+ * SSP Serial Port Registers
+ * PXA250, PXA255, PXA26x and PXA27x SSP controllers are all slightly different.
+ * PXA255, PXA26x and PXA27x have extra ports, registers and bits.
+ */
+
+#define SSCR0		(0x00)  /* SSP Control Register 0 */
+#define SSCR1		(0x04)  /* SSP Control Register 1 */
+#define SSSR		(0x08)  /* SSP Status Register */
+#define SSITR		(0x0C)  /* SSP Interrupt Test Register */
+#define SSDR		(0x10)  /* SSP Data Write/Data Read Register */
+
+#define SSTO		(0x28)  /* SSP Time Out Register */
+#define SSPSP		(0x2C)  /* SSP Programmable Serial Protocol */
+#define SSTSA		(0x30)  /* SSP Tx Timeslot Active */
+#define SSRSA		(0x34)  /* SSP Rx Timeslot Active */
+#define SSTSS		(0x38)  /* SSP Timeslot Status */
+#define SSACD		(0x3C)  /* SSP Audio Clock Divider */
+#define SSACDD		(0x40)	/* SSP Audio Clock Dither Divider */
+
+/* Common PXA2xx bits first */
+#define SSCR0_DSS	(0x0000000f)	/* Data Size Select (mask) */
+#define SSCR0_DataSize(x)  ((x) - 1)	/* Data Size Select [4..16] */
+#define SSCR0_FRF	(0x00000030)	/* FRame Format (mask) */
+#define SSCR0_Motorola	(0x0 << 4)	/* Motorola's Serial Peripheral Interface (SPI) */
+#define SSCR0_TI	(0x1 << 4)	/* Texas Instruments' Synchronous Serial Protocol (SSP) */
+#define SSCR0_National	(0x2 << 4)	/* National Microwire */
+#define SSCR0_ECS	(1 << 6)	/* External clock select */
+#define SSCR0_SSE	(1 << 7)	/* Synchronous Serial Port Enable */
+#define SSCR0_SCR(x)	((x) << 8)	/* Serial Clock Rate (mask) */
+
+/* PXA27x, PXA3xx */
+#define SSCR0_EDSS	(1 << 20)	/* Extended data size select */
+#define SSCR0_NCS	(1 << 21)	/* Network clock select */
+#define SSCR0_RIM	(1 << 22)	/* Receive FIFO overrrun interrupt mask */
+#define SSCR0_TUM	(1 << 23)	/* Transmit FIFO underrun interrupt mask */
+#define SSCR0_FRDC	(0x07000000)	/* Frame rate divider control (mask) */
+#define SSCR0_SlotsPerFrm(x) (((x) - 1) << 24)	/* Time slots per frame [1..8] */
+#define SSCR0_FPCKE	(1 << 29)	/* FIFO packing enable */
+#define SSCR0_ACS	(1 << 30)	/* Audio clock select */
+#define SSCR0_MOD	(1 << 31)	/* Mode (normal or network) */
+
+
+#define SSCR1_RIE	(1 << 0)	/* Receive FIFO Interrupt Enable */
+#define SSCR1_TIE	(1 << 1)	/* Transmit FIFO Interrupt Enable */
+#define SSCR1_LBM	(1 << 2)	/* Loop-Back Mode */
+#define SSCR1_SPO	(1 << 3)	/* Motorola SPI SSPSCLK polarity setting */
+#define SSCR1_SPH	(1 << 4)	/* Motorola SPI SSPSCLK phase setting */
+#define SSCR1_MWDS	(1 << 5)	/* Microwire Transmit Data Size */
+#define SSCR1_TFT	(0x000003c0)	/* Transmit FIFO Threshold (mask) */
+#define SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..16] */
+#define SSCR1_RFT	(0x00003c00)	/* Receive FIFO Threshold (mask) */
+#define SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..16] */
+
+#define SSSR_TNF	(1 << 2)	/* Transmit FIFO Not Full */
+#define SSSR_RNE	(1 << 3)	/* Receive FIFO Not Empty */
+#define SSSR_BSY	(1 << 4)	/* SSP Busy */
+#define SSSR_TFS	(1 << 5)	/* Transmit FIFO Service Request */
+#define SSSR_RFS	(1 << 6)	/* Receive FIFO Service Request */
+#define SSSR_ROR	(1 << 7)	/* Receive FIFO Overrun */
+#define SSSR_TFL_MASK   (0xf << 8)	/* Transmit FIFO Level mask */
+#define SSSR_RFL_MASK   (0xf << 12)	/* Receive FIFO Level mask */
+
+/* extra bits in PXA255, PXA26x and PXA27x SSP ports */
+#define SSCR0_TISSP		(1 << 4)	/* TI Sync Serial Protocol */
+#define SSCR0_PSP		(3 << 4)	/* PSP - Programmable Serial Protocol */
+#define SSCR1_TTELP		(1 << 31)	/* TXD Tristate Enable Last Phase */
+#define SSCR1_TTE		(1 << 30)	/* TXD Tristate Enable */
+#define SSCR1_EBCEI		(1 << 29)	/* Enable Bit Count Error interrupt */
+#define SSCR1_SCFR		(1 << 28)	/* Slave Clock free Running */
+#define SSCR1_ECRA		(1 << 27)	/* Enable Clock Request A */
+#define SSCR1_ECRB		(1 << 26)	/* Enable Clock request B */
+#define SSCR1_SCLKDIR		(1 << 25)	/* Serial Bit Rate Clock Direction */
+#define SSCR1_SFRMDIR		(1 << 24)	/* Frame Direction */
+#define SSCR1_RWOT		(1 << 23)	/* Receive Without Transmit */
+#define SSCR1_TRAIL		(1 << 22)	/* Trailing Byte */
+#define SSCR1_TSRE		(1 << 21)	/* Transmit Service Request Enable */
+#define SSCR1_RSRE		(1 << 20)	/* Receive Service Request Enable */
+#define SSCR1_TINTE		(1 << 19)	/* Receiver Time-out Interrupt enable */
+#define SSCR1_PINTE		(1 << 18)	/* Peripheral Trailing Byte Interupt Enable */
+#define SSCR1_IFS		(1 << 16)	/* Invert Frame Signal */
+#define SSCR1_STRF		(1 << 15)	/* Select FIFO or EFWR */
+#define SSCR1_EFWR		(1 << 14)	/* Enable FIFO Write/Read */
+
+#define SSSR_BCE		(1 << 23)	/* Bit Count Error */
+#define SSSR_CSS		(1 << 22)	/* Clock Synchronisation Status */
+#define SSSR_TUR		(1 << 21)	/* Transmit FIFO Under Run */
+#define SSSR_EOC		(1 << 20)	/* End Of Chain */
+#define SSSR_TINT		(1 << 19)	/* Receiver Time-out Interrupt */
+#define SSSR_PINT		(1 << 18)	/* Peripheral Trailing Byte Interrupt */
+
+
+#define SSPSP_SCMODE(x)		((x) << 0)	/* Serial Bit Rate Clock Mode */
+#define SSPSP_SFRMP		(1 << 2)	/* Serial Frame Polarity */
+#define SSPSP_ETDS		(1 << 3)	/* End of Transfer data State */
+#define SSPSP_STRTDLY(x)	((x) << 4)	/* Start Delay */
+#define SSPSP_DMYSTRT(x)	((x) << 7)	/* Dummy Start */
+#define SSPSP_SFRMDLY(x)	((x) << 9)	/* Serial Frame Delay */
+#define SSPSP_SFRMWDTH(x)	((x) << 16)	/* Serial Frame Width */
+#define SSPSP_DMYSTOP(x)	((x) << 23)	/* Dummy Stop */
+#define SSPSP_FSRT		(1 << 25)	/* Frame Sync Relative Timing */
+
+/* PXA3xx */
+#define SSPSP_EDMYSTRT(x)	((x) << 26)     /* Extended Dummy Start */
+#define SSPSP_EDMYSTOP(x)	((x) << 28)     /* Extended Dummy Stop */
+#define SSPSP_TIMING_MASK	(0x7f8001f0)
+
+#define SSACD_SCDB		(1 << 3)	/* SSPSYSCLK Divider Bypass */
+#define SSACD_ACPS(x)		((x) << 4)	/* Audio clock PLL select */
+#define SSACD_ACDS(x)		((x) << 0)	/* Audio clock divider select */
+#define SSACD_SCDX8		(1 << 7)	/* SYSCLK division ratio select */
+
+enum pxa_ssp_type {
+	SSP_UNDEFINED = 0,
+	PXA25x_SSP,  /* pxa 210, 250, 255, 26x */
+	PXA25x_NSSP, /* pxa 255, 26x (including ASSP) */
+	PXA27x_SSP,
+	PXA168_SSP,
+};
+
+struct ssp_device {
+	struct platform_device *pdev;
+	struct list_head	node;
+
+	struct clk	*clk;
+	void __iomem	*mmio_base;
+	unsigned long	phys_base;
+
+	const char	*label;
+	int		port_id;
+	int		type;
+	int		use_count;
+	int		irq;
+	int		drcmr_rx;
+	int		drcmr_tx;
+};
+
+/**
+ * pxa_ssp_write_reg - Write to a SSP register
+ *
+ * @dev: SSP device to access
+ * @reg: Register to write to
+ * @val: Value to be written.
+ */
+static inline void pxa_ssp_write_reg(struct ssp_device *dev, u32 reg, u32 val)
+{
+	__raw_writel(val, dev->mmio_base + reg);
+}
+
+/**
+ * pxa_ssp_read_reg - Read from a SSP register
+ *
+ * @dev: SSP device to access
+ * @reg: Register to read from
+ */
+static inline u32 pxa_ssp_read_reg(struct ssp_device *dev, u32 reg)
+{
+	return __raw_readl(dev->mmio_base + reg);
+}
+
+struct ssp_device *pxa_ssp_request(int port, const char *label);
+void pxa_ssp_free(struct ssp_device *);
+#endif
diff --git a/include/linux/spi/pxa2xx_spi.h b/include/linux/spi/pxa2xx_spi.h
new file mode 100644
index 000000000000..471ed6889113
--- /dev/null
+++ b/include/linux/spi/pxa2xx_spi.h
@@ -0,0 +1,49 @@
+/*
+ * Copyright (C) 2005 Stephen Street / StreetFire Sound Labs
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+#ifndef __linux_pxa2xx_spi_h
+#define __linux_pxa2xx_spi_h
+
+#include <linux/pxa2xx_ssp.h>
+#include <mach/dma.h>
+
+#define PXA2XX_CS_ASSERT (0x01)
+#define PXA2XX_CS_DEASSERT (0x02)
+
+/* device.platform_data for SSP controller devices */
+struct pxa2xx_spi_master {
+	u32 clock_enable;
+	u16 num_chipselect;
+	u8 enable_dma;
+};
+
+/* spi_board_info.controller_data for SPI slave devices,
+ * copied to spi_device.platform_data ... mostly for dma tuning
+ */
+struct pxa2xx_spi_chip {
+	u8 tx_threshold;
+	u8 rx_threshold;
+	u8 dma_burst_size;
+	u32 timeout;
+	u8 enable_loopback;
+	int gpio_cs;
+	void (*cs_control)(u32 command);
+};
+
+extern void pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_master *info);
+
+#endif
diff --git a/sound/soc/pxa/pxa-ssp.c b/sound/soc/pxa/pxa-ssp.c
index b439eee462cb..8ad93ee2e92b 100644
--- a/sound/soc/pxa/pxa-ssp.c
+++ b/sound/soc/pxa/pxa-ssp.c
@@ -20,6 +20,7 @@
 #include <linux/platform_device.h>
 #include <linux/clk.h>
 #include <linux/io.h>
+#include <linux/pxa2xx_ssp.h>
 
 #include <asm/irq.h>
 
@@ -33,7 +34,6 @@
 #include <mach/hardware.h>
 #include <mach/dma.h>
 #include <mach/audio.h>
-#include <plat/ssp.h>
 
 #include "../../arm/pxa2xx-pcm.h"
 #include "pxa-ssp.h"
-- 
cgit v1.2.3-55-g7522


From d6ea3df0d470fb9260db93883f97764cf9f0e562 Mon Sep 17 00:00:00 2001
From: Sebastian Andrzej Siewior
Date: Wed, 24 Nov 2010 10:17:14 +0100
Subject: spi/pxa2xx: Add CE4100 support

Sodaville's SPI controller is very much the same as in PXA25x. The
difference:
- The RX/TX FIFO is only 4 words deep instead of 16
- No DMA support
- The SPI controller offers a CS functionality

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
---
 drivers/spi/Kconfig            |  13 ++-
 drivers/spi/Makefile           |   1 +
 drivers/spi/pxa2xx_spi.c       |   1 -
 drivers/spi/pxa2xx_spi_pci.c   | 201 +++++++++++++++++++++++++++++++++++++++++
 include/linux/spi/pxa2xx_spi.h | 105 ++++++++++++++++++++-
 5 files changed, 314 insertions(+), 7 deletions(-)
 create mode 100644 drivers/spi/pxa2xx_spi_pci.c

(limited to 'drivers')

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 78f9fd02c1b2..537759011d1d 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -267,12 +267,15 @@ config SPI_PPC4xx
 
 config SPI_PXA2XX
 	tristate "PXA2xx SSP SPI master"
-	depends on ARCH_PXA && EXPERIMENTAL
-	select PXA_SSP
+	depends on (ARCH_PXA || (X86_32 && PCI)) && EXPERIMENTAL
+	select PXA_SSP if ARCH_PXA
 	help
-	  This enables using a PXA2xx SSP port as a SPI master controller.
-	  The driver can be configured to use any SSP port and additional
-	  documentation can be found a Documentation/spi/pxa2xx.
+	  This enables using a PXA2xx or Sodaville SSP port as a SPI master
+	  controller. The driver can be configured to use any SSP port and
+	  additional documentation can be found a Documentation/spi/pxa2xx.
+
+config SPI_PXA2XX_PCI
+	def_bool SPI_PXA2XX && X86_32 && PCI
 
 config SPI_S3C24XX
 	tristate "Samsung S3C24XX series SPI"
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 8bc1a5abac1f..bdc4c400fd71 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -24,6 +24,7 @@ obj-$(CONFIG_SPI_GPIO)			+= spi_gpio.o
 obj-$(CONFIG_SPI_IMX)			+= spi_imx.o
 obj-$(CONFIG_SPI_LM70_LLP)		+= spi_lm70llp.o
 obj-$(CONFIG_SPI_PXA2XX)		+= pxa2xx_spi.o
+obj-$(CONFIG_SPI_PXA2XX_PCI)		+= pxa2xx_spi_pci.o
 obj-$(CONFIG_SPI_OMAP_UWIRE)		+= omap_uwire.o
 obj-$(CONFIG_SPI_OMAP24XX)		+= omap2_mcspi.o
 obj-$(CONFIG_SPI_OMAP_100K)		+= omap_spi_100k.o
diff --git a/drivers/spi/pxa2xx_spi.c b/drivers/spi/pxa2xx_spi.c
index 98d9c8b09182..ed212c2583ab 100644
--- a/drivers/spi/pxa2xx_spi.c
+++ b/drivers/spi/pxa2xx_spi.c
@@ -28,7 +28,6 @@
 #include <linux/spi/spi.h>
 #include <linux/workqueue.h>
 #include <linux/delay.h>
-#include <linux/clk.h>
 #include <linux/gpio.h>
 #include <linux/slab.h>
 
diff --git a/drivers/spi/pxa2xx_spi_pci.c b/drivers/spi/pxa2xx_spi_pci.c
new file mode 100644
index 000000000000..351d8a375b57
--- /dev/null
+++ b/drivers/spi/pxa2xx_spi_pci.c
@@ -0,0 +1,201 @@
+/*
+ * CE4100's SPI device is more or less the same one as found on PXA
+ *
+ */
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/of_device.h>
+#include <linux/spi/pxa2xx_spi.h>
+
+struct awesome_struct {
+	struct ssp_device ssp;
+	struct platform_device spi_pdev;
+	struct pxa2xx_spi_master spi_pdata;
+};
+
+static DEFINE_MUTEX(ssp_lock);
+static LIST_HEAD(ssp_list);
+
+struct ssp_device *pxa_ssp_request(int port, const char *label)
+{
+	struct ssp_device *ssp = NULL;
+
+	mutex_lock(&ssp_lock);
+
+	list_for_each_entry(ssp, &ssp_list, node) {
+		if (ssp->port_id == port && ssp->use_count == 0) {
+			ssp->use_count++;
+			ssp->label = label;
+			break;
+		}
+	}
+
+	mutex_unlock(&ssp_lock);
+
+	if (&ssp->node == &ssp_list)
+		return NULL;
+
+	return ssp;
+}
+EXPORT_SYMBOL_GPL(pxa_ssp_request);
+
+void pxa_ssp_free(struct ssp_device *ssp)
+{
+	mutex_lock(&ssp_lock);
+	if (ssp->use_count) {
+		ssp->use_count--;
+		ssp->label = NULL;
+	} else
+		dev_err(&ssp->pdev->dev, "device already free\n");
+	mutex_unlock(&ssp_lock);
+}
+EXPORT_SYMBOL_GPL(pxa_ssp_free);
+
+static void plat_dev_release(struct device *dev)
+{
+	struct awesome_struct *as = container_of(dev,
+			struct awesome_struct, spi_pdev.dev);
+
+	of_device_node_put(&as->spi_pdev.dev);
+}
+
+static int __devinit ce4100_spi_probe(struct pci_dev *dev,
+		const struct pci_device_id *ent)
+{
+	int ret;
+	resource_size_t phys_beg;
+	resource_size_t phys_len;
+	struct awesome_struct *spi_info;
+	struct platform_device *pdev;
+	struct pxa2xx_spi_master *spi_pdata;
+	struct ssp_device *ssp;
+
+	ret = pci_enable_device(dev);
+	if (ret)
+		return ret;
+
+	phys_beg = pci_resource_start(dev, 0);
+	phys_len = pci_resource_len(dev, 0);
+
+	if (!request_mem_region(phys_beg, phys_len,
+				"CE4100 SPI")) {
+		dev_err(&dev->dev, "Can't request register space.\n");
+		ret = -EBUSY;
+		return ret;
+	}
+
+	spi_info = kzalloc(sizeof(*spi_info), GFP_KERNEL);
+	if (!spi_info) {
+		ret = -ENOMEM;
+		goto err_kz;
+	}
+	ssp = &spi_info->ssp;
+	pdev = &spi_info->spi_pdev;
+	spi_pdata =  &spi_info->spi_pdata;
+
+	pdev->name = "pxa2xx-spi";
+	pdev->id = dev->devfn;
+	pdev->dev.parent = &dev->dev;
+	pdev->dev.platform_data = &spi_info->spi_pdata;
+
+#ifdef CONFIG_OF
+	pdev->dev.of_node = dev->dev.of_node;
+#endif
+	pdev->dev.release = plat_dev_release;
+
+	spi_pdata->num_chipselect = dev->devfn;
+
+	ssp->phys_base = pci_resource_start(dev, 0);
+	ssp->mmio_base = ioremap(phys_beg, phys_len);
+	if (!ssp->mmio_base) {
+		dev_err(&pdev->dev, "failed to ioremap() registers\n");
+		ret = -EIO;
+		goto err_remap;
+	}
+	ssp->irq = dev->irq;
+	ssp->port_id = pdev->id;
+	ssp->type = PXA25x_SSP;
+
+	mutex_lock(&ssp_lock);
+	list_add(&ssp->node, &ssp_list);
+	mutex_unlock(&ssp_lock);
+
+	pci_set_drvdata(dev, spi_info);
+
+	ret = platform_device_register(pdev);
+	if (ret)
+		goto err_dev_add;
+
+	return ret;
+
+err_dev_add:
+	pci_set_drvdata(dev, NULL);
+	mutex_lock(&ssp_lock);
+	list_del(&ssp->node);
+	mutex_unlock(&ssp_lock);
+	iounmap(ssp->mmio_base);
+
+err_remap:
+	kfree(spi_info);
+
+err_kz:
+	release_mem_region(phys_beg, phys_len);
+
+	return ret;
+}
+
+static void __devexit ce4100_spi_remove(struct pci_dev *dev)
+{
+	struct awesome_struct *spi_info;
+	struct platform_device *pdev;
+	struct ssp_device *ssp;
+
+	spi_info = pci_get_drvdata(dev);
+
+	ssp = &spi_info->ssp;
+	pdev = &spi_info->spi_pdev;
+
+	platform_device_unregister(pdev);
+
+	iounmap(ssp->mmio_base);
+	release_mem_region(pci_resource_start(dev, 0),
+			pci_resource_len(dev, 0));
+
+	mutex_lock(&ssp_lock);
+	list_del(&ssp->node);
+	mutex_unlock(&ssp_lock);
+
+	pci_set_drvdata(dev, NULL);
+	pci_disable_device(dev);
+	kfree(spi_info);
+}
+
+static struct pci_device_id ce4100_spi_devices[] __devinitdata = {
+
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x2e6a) },
+	{ },
+};
+MODULE_DEVICE_TABLE(pci, ce4100_spi_devices);
+
+static struct pci_driver ce4100_spi_driver = {
+	.name           = "ce4100_spi",
+	.id_table       = ce4100_spi_devices,
+	.probe          = ce4100_spi_probe,
+	.remove         = __devexit_p(ce4100_spi_remove),
+};
+
+static int __init ce4100_spi_init(void)
+{
+	return pci_register_driver(&ce4100_spi_driver);
+}
+module_init(ce4100_spi_init);
+
+static void __exit ce4100_spi_exit(void)
+{
+	pci_unregister_driver(&ce4100_spi_driver);
+}
+module_exit(ce4100_spi_exit);
+
+MODULE_DESCRIPTION("CE4100 PCI-SPI glue code for PXA's driver");
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Sebastian Andrzej Siewior <bigeasy@linutronix.de>");
diff --git a/include/linux/spi/pxa2xx_spi.h b/include/linux/spi/pxa2xx_spi.h
index 471ed6889113..d3e1075f7b60 100644
--- a/include/linux/spi/pxa2xx_spi.h
+++ b/include/linux/spi/pxa2xx_spi.h
@@ -19,7 +19,6 @@
 #define __linux_pxa2xx_spi_h
 
 #include <linux/pxa2xx_ssp.h>
-#include <mach/dma.h>
 
 #define PXA2XX_CS_ASSERT (0x01)
 #define PXA2XX_CS_DEASSERT (0x02)
@@ -44,6 +43,110 @@ struct pxa2xx_spi_chip {
 	void (*cs_control)(u32 command);
 };
 
+#ifdef CONFIG_ARCH_PXA
+
+#include <linux/clk.h>
+#include <mach/dma.h>
+
 extern void pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_master *info);
 
+#else
+/*
+ * This is the implemtation for CE4100 on x86. ARM defines them in mach/ or
+ * plat/ include path.
+ * The CE4100 does not provide DMA support. This bits are here to let the driver
+ * compile and will never be used. Maybe we get DMA support at a later point in
+ * time.
+ */
+
+#define DCSR(n)         (n)
+#define DSADR(n)        (n)
+#define DTADR(n)        (n)
+#define DCMD(n)         (n)
+#define DRCMR(n)        (n)
+
+#define DCSR_RUN	(1 << 31)	/* Run Bit */
+#define DCSR_NODESC	(1 << 30)	/* No-Descriptor Fetch */
+#define DCSR_STOPIRQEN	(1 << 29)	/* Stop Interrupt Enable */
+#define DCSR_REQPEND	(1 << 8)	/* Request Pending (read-only) */
+#define DCSR_STOPSTATE	(1 << 3)	/* Stop State (read-only) */
+#define DCSR_ENDINTR	(1 << 2)	/* End Interrupt */
+#define DCSR_STARTINTR	(1 << 1)	/* Start Interrupt */
+#define DCSR_BUSERR	(1 << 0)	/* Bus Error Interrupt */
+
+#define DCSR_EORIRQEN	(1 << 28)	/* End of Receive Interrupt Enable */
+#define DCSR_EORJMPEN	(1 << 27)	/* Jump to next descriptor on EOR */
+#define DCSR_EORSTOPEN	(1 << 26)	/* STOP on an EOR */
+#define DCSR_SETCMPST	(1 << 25)	/* Set Descriptor Compare Status */
+#define DCSR_CLRCMPST	(1 << 24)	/* Clear Descriptor Compare Status */
+#define DCSR_CMPST	(1 << 10)	/* The Descriptor Compare Status */
+#define DCSR_EORINTR	(1 << 9)	/* The end of Receive */
+
+#define DRCMR_MAPVLD	(1 << 7)	/* Map Valid */
+#define DRCMR_CHLNUM	0x1f		/* mask for Channel Number */
+
+#define DDADR_DESCADDR	0xfffffff0	/* Address of next descriptor */
+#define DDADR_STOP	(1 << 0)	/* Stop */
+
+#define DCMD_INCSRCADDR	(1 << 31)	/* Source Address Increment Setting. */
+#define DCMD_INCTRGADDR	(1 << 30)	/* Target Address Increment Setting. */
+#define DCMD_FLOWSRC	(1 << 29)	/* Flow Control by the source. */
+#define DCMD_FLOWTRG	(1 << 28)	/* Flow Control by the target. */
+#define DCMD_STARTIRQEN	(1 << 22)	/* Start Interrupt Enable */
+#define DCMD_ENDIRQEN	(1 << 21)	/* End Interrupt Enable */
+#define DCMD_ENDIAN	(1 << 18)	/* Device Endian-ness. */
+#define DCMD_BURST8	(1 << 16)	/* 8 byte burst */
+#define DCMD_BURST16	(2 << 16)	/* 16 byte burst */
+#define DCMD_BURST32	(3 << 16)	/* 32 byte burst */
+#define DCMD_WIDTH1	(1 << 14)	/* 1 byte width */
+#define DCMD_WIDTH2	(2 << 14)	/* 2 byte width (HalfWord) */
+#define DCMD_WIDTH4	(3 << 14)	/* 4 byte width (Word) */
+#define DCMD_LENGTH	0x01fff		/* length mask (max = 8K - 1) */
+
+/*
+ * Descriptor structure for PXA's DMA engine
+ * Note: this structure must always be aligned to a 16-byte boundary.
+ */
+
+typedef enum {
+	DMA_PRIO_HIGH = 0,
+	DMA_PRIO_MEDIUM = 1,
+	DMA_PRIO_LOW = 2
+} pxa_dma_prio;
+
+/*
+ * DMA registration
+ */
+
+static inline int pxa_request_dma(char *name,
+		pxa_dma_prio prio,
+		void (*irq_handler)(int, void *),
+		void *data)
+{
+	return -ENODEV;
+}
+
+static inline void pxa_free_dma(int dma_ch)
+{
+}
+
+/*
+ * The CE4100 does not have the clk framework implemented and SPI clock can
+ * not be switched on/off or the divider changed.
+ */
+static inline void clk_disable(struct clk *clk)
+{
+}
+
+static inline int clk_enable(struct clk *clk)
+{
+	return 0;
+}
+
+static inline unsigned long clk_get_rate(struct clk *clk)
+{
+	return 3686400;
+}
+
+#endif
 #endif
-- 
cgit v1.2.3-55-g7522


From d0777f2c3eda180e3fc549e0efbe741014f17689 Mon Sep 17 00:00:00 2001
From: Sebastian Andrzej Siewior
Date: Mon, 22 Nov 2010 17:12:16 -0800
Subject: spi/pxa2xx: Consider CE4100's FIFO depth

For PXA the default threshold is FIFO_DEPTH / 2. Adjust this value for
CE4100.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
---
 drivers/spi/pxa2xx_spi.c   |  2 --
 include/linux/pxa2xx_ssp.h | 32 ++++++++++++++++++++++++++------
 2 files changed, 26 insertions(+), 8 deletions(-)

(limited to 'drivers')

diff --git a/drivers/spi/pxa2xx_spi.c b/drivers/spi/pxa2xx_spi.c
index ed212c2583ab..81cfbbc58e94 100644
--- a/drivers/spi/pxa2xx_spi.c
+++ b/drivers/spi/pxa2xx_spi.c
@@ -43,8 +43,6 @@ MODULE_ALIAS("platform:pxa2xx-spi");
 
 #define MAX_BUSES 3
 
-#define RX_THRESH_DFLT 	8
-#define TX_THRESH_DFLT 	8
 #define TIMOUT_DFLT		1000
 
 #define DMA_INT_MASK		(DCSR_ENDINTR | DCSR_STARTINTR | DCSR_BUSERR)
diff --git a/include/linux/pxa2xx_ssp.h b/include/linux/pxa2xx_ssp.h
index 84465d4a51b7..c3aa334cbb9b 100644
--- a/include/linux/pxa2xx_ssp.h
+++ b/include/linux/pxa2xx_ssp.h
@@ -71,10 +71,6 @@
 #define SSCR1_SPO	(1 << 3)	/* Motorola SPI SSPSCLK polarity setting */
 #define SSCR1_SPH	(1 << 4)	/* Motorola SPI SSPSCLK phase setting */
 #define SSCR1_MWDS	(1 << 5)	/* Microwire Transmit Data Size */
-#define SSCR1_TFT	(0x000003c0)	/* Transmit FIFO Threshold (mask) */
-#define SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..16] */
-#define SSCR1_RFT	(0x00003c00)	/* Receive FIFO Threshold (mask) */
-#define SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..16] */
 
 #define SSSR_TNF	(1 << 2)	/* Transmit FIFO Not Full */
 #define SSSR_RNE	(1 << 3)	/* Receive FIFO Not Empty */
@@ -82,8 +78,32 @@
 #define SSSR_TFS	(1 << 5)	/* Transmit FIFO Service Request */
 #define SSSR_RFS	(1 << 6)	/* Receive FIFO Service Request */
 #define SSSR_ROR	(1 << 7)	/* Receive FIFO Overrun */
-#define SSSR_TFL_MASK   (0xf << 8)	/* Transmit FIFO Level mask */
-#define SSSR_RFL_MASK   (0xf << 12)	/* Receive FIFO Level mask */
+
+#ifdef CONFIG_ARCH_PXA
+#define RX_THRESH_DFLT	8
+#define TX_THRESH_DFLT	8
+
+#define SSSR_TFL_MASK	(0xf << 8)	/* Transmit FIFO Level mask */
+#define SSSR_RFL_MASK	(0xf << 12)	/* Receive FIFO Level mask */
+
+#define SSCR1_TFT	(0x000003c0)	/* Transmit FIFO Threshold (mask) */
+#define SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..16] */
+#define SSCR1_RFT	(0x00003c00)	/* Receive FIFO Threshold (mask) */
+#define SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..16] */
+
+#else
+
+#define RX_THRESH_DFLT	2
+#define TX_THRESH_DFLT	2
+
+#define SSSR_TFL_MASK	(0x3 << 8)	/* Transmit FIFO Level mask */
+#define SSSR_RFL_MASK	(0x3 << 12)	/* Receive FIFO Level mask */
+
+#define SSCR1_TFT	(0x000000c0)	/* Transmit FIFO Threshold (mask) */
+#define SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..4] */
+#define SSCR1_RFT	(0x00000c00)	/* Receive FIFO Threshold (mask) */
+#define SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..4] */
+#endif
 
 /* extra bits in PXA255, PXA26x and PXA27x SSP ports */
 #define SSCR0_TISSP		(1 << 4)	/* TI Sync Serial Protocol */
-- 
cgit v1.2.3-55-g7522


From 2a8626a9e2d86d114a2d9f813a1acebf9d53dd10 Mon Sep 17 00:00:00 2001
From: Sebastian Andrzej Siewior
Date: Mon, 22 Nov 2010 17:12:17 -0800
Subject: spi/pxa2xx: Add chipselect support for Sodaville

The SPI core on Sodaville supports chip selects. Its configuration
moved into the SSSR register at bit 0 and 1. Thus Sodaville can be hooked
up with up to 4 devices.
This patch ensures that the bits which are otherwiese reserved are only
touched on Sodaville and not on any other PXAs. Also it makes sure that
the status register does not lose the CS information while clearing the
ROR bit.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
---
 drivers/spi/pxa2xx_spi.c   | 93 +++++++++++++++++++++++++++++++++-------------
 include/linux/pxa2xx_ssp.h |  2 +
 2 files changed, 70 insertions(+), 25 deletions(-)

(limited to 'drivers')

diff --git a/drivers/spi/pxa2xx_spi.c b/drivers/spi/pxa2xx_spi.c
index 81cfbbc58e94..a54685bb7e53 100644
--- a/drivers/spi/pxa2xx_spi.c
+++ b/drivers/spi/pxa2xx_spi.c
@@ -163,7 +163,10 @@ struct chip_data {
 	u8 enable_dma;
 	u8 bits_per_word;
 	u32 speed_hz;
-	int gpio_cs;
+	union {
+		int gpio_cs;
+		unsigned int frm;
+	};
 	int gpio_cs_inverted;
 	int (*write)(struct driver_data *drv_data);
 	int (*read)(struct driver_data *drv_data);
@@ -176,6 +179,11 @@ static void cs_assert(struct driver_data *drv_data)
 {
 	struct chip_data *chip = drv_data->cur_chip;
 
+	if (drv_data->ssp_type == CE4100_SSP) {
+		write_SSSR(drv_data->cur_chip->frm, drv_data->ioaddr);
+		return;
+	}
+
 	if (chip->cs_control) {
 		chip->cs_control(PXA2XX_CS_ASSERT);
 		return;
@@ -189,6 +197,9 @@ static void cs_deassert(struct driver_data *drv_data)
 {
 	struct chip_data *chip = drv_data->cur_chip;
 
+	if (drv_data->ssp_type == CE4100_SSP)
+		return;
+
 	if (chip->cs_control) {
 		chip->cs_control(PXA2XX_CS_DEASSERT);
 		return;
@@ -198,6 +209,25 @@ static void cs_deassert(struct driver_data *drv_data)
 		gpio_set_value(chip->gpio_cs, !chip->gpio_cs_inverted);
 }
 
+static void write_SSSR_CS(struct driver_data *drv_data, u32 val)
+{
+	void __iomem *reg = drv_data->ioaddr;
+
+	if (drv_data->ssp_type == CE4100_SSP)
+		val |= read_SSSR(reg) & SSSR_ALT_FRM_MASK;
+
+	write_SSSR(val, reg);
+}
+
+static int pxa25x_ssp_comp(struct driver_data *drv_data)
+{
+	if (drv_data->ssp_type == PXA25x_SSP)
+		return 1;
+	if (drv_data->ssp_type == CE4100_SSP)
+		return 1;
+	return 0;
+}
+
 static int flush(struct driver_data *drv_data)
 {
 	unsigned long limit = loops_per_jiffy << 1;
@@ -209,7 +239,7 @@ static int flush(struct driver_data *drv_data)
 			read_SSDR(reg);
 		}
 	} while ((read_SSSR(reg) & SSSR_BSY) && --limit);
-	write_SSSR(SSSR_ROR, reg);
+	write_SSSR_CS(drv_data, SSSR_ROR);
 
 	return limit;
 }
@@ -502,9 +532,9 @@ static void dma_error_stop(struct driver_data *drv_data, const char *msg)
 	/* Stop and reset */
 	DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
 	DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
-	write_SSSR(drv_data->clear_sr, reg);
+	write_SSSR_CS(drv_data, drv_data->clear_sr);
 	write_SSCR1(read_SSCR1(reg) & ~drv_data->dma_cr1, reg);
-	if (drv_data->ssp_type != PXA25x_SSP)
+	if (!pxa25x_ssp_comp(drv_data))
 		write_SSTO(0, reg);
 	flush(drv_data);
 	write_SSCR0(read_SSCR0(reg) & ~SSCR0_SSE, reg);
@@ -524,7 +554,7 @@ static void dma_transfer_complete(struct driver_data *drv_data)
 
 	/* Clear and disable interrupts on SSP and DMA channels*/
 	write_SSCR1(read_SSCR1(reg) & ~drv_data->dma_cr1, reg);
-	write_SSSR(drv_data->clear_sr, reg);
+	write_SSSR_CS(drv_data, drv_data->clear_sr);
 	DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
 	DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
 
@@ -617,7 +647,7 @@ static irqreturn_t dma_transfer(struct driver_data *drv_data)
 
 		/* Clear and disable timeout interrupt, do the rest in
 		 * dma_transfer_complete */
-		if (drv_data->ssp_type != PXA25x_SSP)
+		if (!pxa25x_ssp_comp(drv_data))
 			write_SSTO(0, reg);
 
 		/* finish this transfer, start the next */
@@ -635,9 +665,9 @@ static void int_error_stop(struct driver_data *drv_data, const char* msg)
 	void __iomem *reg = drv_data->ioaddr;
 
 	/* Stop and reset SSP */
-	write_SSSR(drv_data->clear_sr, reg);
+	write_SSSR_CS(drv_data, drv_data->clear_sr);
 	write_SSCR1(read_SSCR1(reg) & ~drv_data->int_cr1, reg);
-	if (drv_data->ssp_type != PXA25x_SSP)
+	if (!pxa25x_ssp_comp(drv_data))
 		write_SSTO(0, reg);
 	flush(drv_data);
 	write_SSCR0(read_SSCR0(reg) & ~SSCR0_SSE, reg);
@@ -653,9 +683,9 @@ static void int_transfer_complete(struct driver_data *drv_data)
 	void __iomem *reg = drv_data->ioaddr;
 
 	/* Stop SSP */
-	write_SSSR(drv_data->clear_sr, reg);
+	write_SSSR_CS(drv_data, drv_data->clear_sr);
 	write_SSCR1(read_SSCR1(reg) & ~drv_data->int_cr1, reg);
-	if (drv_data->ssp_type != PXA25x_SSP)
+	if (!pxa25x_ssp_comp(drv_data))
 		write_SSTO(0, reg);
 
 	/* Update total byte transfered return count actual bytes read */
@@ -711,7 +741,7 @@ static irqreturn_t interrupt_transfer(struct driver_data *drv_data)
 	if (drv_data->tx == drv_data->tx_end) {
 		write_SSCR1(read_SSCR1(reg) & ~SSCR1_TIE, reg);
 		/* PXA25x_SSP has no timeout, read trailing bytes */
-		if (drv_data->ssp_type == PXA25x_SSP) {
+		if (pxa25x_ssp_comp(drv_data)) {
 			if (!wait_ssp_rx_stall(reg))
 			{
 				int_error_stop(drv_data, "interrupt_transfer: "
@@ -754,9 +784,9 @@ static irqreturn_t ssp_int(int irq, void *dev_id)
 
 		write_SSCR0(read_SSCR0(reg) & ~SSCR0_SSE, reg);
 		write_SSCR1(read_SSCR1(reg) & ~drv_data->int_cr1, reg);
-		if (drv_data->ssp_type != PXA25x_SSP)
+		if (!pxa25x_ssp_comp(drv_data))
 			write_SSTO(0, reg);
-		write_SSSR(drv_data->clear_sr, reg);
+		write_SSSR_CS(drv_data, drv_data->clear_sr);
 
 		dev_err(&drv_data->pdev->dev, "bad message state "
 			"in interrupt handler\n");
@@ -869,7 +899,7 @@ static unsigned int ssp_get_clk_div(struct ssp_device *ssp, int rate)
 {
 	unsigned long ssp_clk = clk_get_rate(ssp->clk);
 
-	if (ssp->type == PXA25x_SSP)
+	if (ssp->type == PXA25x_SSP || ssp->type == CE4100_SSP)
 		return ((ssp_clk / (2 * rate) - 1) & 0xff) << 8;
 	else
 		return ((ssp_clk / rate - 1) & 0xfff) << 8;
@@ -1095,7 +1125,7 @@ static void pump_transfers(unsigned long data)
 
 		/* Clear status  */
 		cr1 = chip->cr1 | chip->threshold | drv_data->int_cr1;
-		write_SSSR(drv_data->clear_sr, reg);
+		write_SSSR_CS(drv_data, drv_data->clear_sr);
 	}
 
 	/* see if we need to reload the config registers */
@@ -1105,7 +1135,7 @@ static void pump_transfers(unsigned long data)
 
 		/* stop the SSP, and update the other bits */
 		write_SSCR0(cr0 & ~SSCR0_SSE, reg);
-		if (drv_data->ssp_type != PXA25x_SSP)
+		if (!pxa25x_ssp_comp(drv_data))
 			write_SSTO(chip->timeout, reg);
 		/* first set CR1 without interrupt and service enables */
 		write_SSCR1(cr1 & SSCR1_CHANGE_MASK, reg);
@@ -1113,7 +1143,7 @@ static void pump_transfers(unsigned long data)
 		write_SSCR0(cr0, reg);
 
 	} else {
-		if (drv_data->ssp_type != PXA25x_SSP)
+		if (!pxa25x_ssp_comp(drv_data))
 			write_SSTO(chip->timeout, reg);
 	}
 
@@ -1240,14 +1270,13 @@ static int setup(struct spi_device *spi)
 	uint tx_thres = TX_THRESH_DFLT;
 	uint rx_thres = RX_THRESH_DFLT;
 
-	if (drv_data->ssp_type != PXA25x_SSP
+	if (!pxa25x_ssp_comp(drv_data)
 		&& (spi->bits_per_word < 4 || spi->bits_per_word > 32)) {
 		dev_err(&spi->dev, "failed setup: ssp_type=%d, bits/wrd=%d "
 				"b/w not 4-32 for type non-PXA25x_SSP\n",
 				drv_data->ssp_type, spi->bits_per_word);
 		return -EINVAL;
-	}
-	else if (drv_data->ssp_type == PXA25x_SSP
+	} else if (pxa25x_ssp_comp(drv_data)
 			&& (spi->bits_per_word < 4
 				|| spi->bits_per_word > 16)) {
 		dev_err(&spi->dev, "failed setup: ssp_type=%d, bits/wrd=%d "
@@ -1266,7 +1295,17 @@ static int setup(struct spi_device *spi)
 			return -ENOMEM;
 		}
 
-		chip->gpio_cs = -1;
+		if (drv_data->ssp_type == CE4100_SSP) {
+			if (spi->chip_select > 4) {
+				dev_err(&spi->dev, "failed setup: "
+				"cs number must not be > 4.\n");
+				kfree(chip);
+				return -EINVAL;
+			}
+
+			chip->frm = spi->chip_select;
+		} else
+			chip->gpio_cs = -1;
 		chip->enable_dma = 0;
 		chip->timeout = TIMOUT_DFLT;
 		chip->dma_burst_size = drv_data->master_info->enable_dma ?
@@ -1322,7 +1361,7 @@ static int setup(struct spi_device *spi)
 			| (((spi->mode & SPI_CPOL) != 0) ? SSCR1_SPO : 0);
 
 	/* NOTE:  PXA25x_SSP _could_ use external clocking ... */
-	if (drv_data->ssp_type != PXA25x_SSP)
+	if (!pxa25x_ssp_comp(drv_data))
 		dev_dbg(&spi->dev, "%ld Hz actual, %s\n",
 			clk_get_rate(ssp->clk)
 				/ (1 + ((chip->cr0 & SSCR0_SCR(0xfff)) >> 8)),
@@ -1357,17 +1396,21 @@ static int setup(struct spi_device *spi)
 
 	spi_set_ctldata(spi, chip);
 
+	if (drv_data->ssp_type == CE4100_SSP)
+		return 0;
+
 	return setup_cs(spi, chip, chip_info);
 }
 
 static void cleanup(struct spi_device *spi)
 {
 	struct chip_data *chip = spi_get_ctldata(spi);
+	struct driver_data *drv_data = spi_master_get_devdata(spi->master);
 
 	if (!chip)
 		return;
 
-	if (gpio_is_valid(chip->gpio_cs))
+	if (drv_data->ssp_type != CE4100_SSP && gpio_is_valid(chip->gpio_cs))
 		gpio_free(chip->gpio_cs);
 
 	kfree(chip);
@@ -1507,7 +1550,7 @@ static int __devinit pxa2xx_spi_probe(struct platform_device *pdev)
 
 	drv_data->ioaddr = ssp->mmio_base;
 	drv_data->ssdr_physical = ssp->phys_base + SSDR;
-	if (ssp->type == PXA25x_SSP) {
+	if (pxa25x_ssp_comp(drv_data)) {
 		drv_data->int_cr1 = SSCR1_TIE | SSCR1_RIE;
 		drv_data->dma_cr1 = 0;
 		drv_data->clear_sr = SSSR_ROR;
@@ -1569,7 +1612,7 @@ static int __devinit pxa2xx_spi_probe(struct platform_device *pdev)
 			| SSCR0_Motorola
 			| SSCR0_DataSize(8),
 			drv_data->ioaddr);
-	if (drv_data->ssp_type != PXA25x_SSP)
+	if (!pxa25x_ssp_comp(drv_data))
 		write_SSTO(0, drv_data->ioaddr);
 	write_SSPSP(0, drv_data->ioaddr);
 
diff --git a/include/linux/pxa2xx_ssp.h b/include/linux/pxa2xx_ssp.h
index c3aa334cbb9b..2f691e4e6222 100644
--- a/include/linux/pxa2xx_ssp.h
+++ b/include/linux/pxa2xx_ssp.h
@@ -72,6 +72,7 @@
 #define SSCR1_SPH	(1 << 4)	/* Motorola SPI SSPSCLK phase setting */
 #define SSCR1_MWDS	(1 << 5)	/* Microwire Transmit Data Size */
 
+#define SSSR_ALT_FRM_MASK	3	/* Masks the SFRM signal number */
 #define SSSR_TNF	(1 << 2)	/* Transmit FIFO Not Full */
 #define SSSR_RNE	(1 << 3)	/* Receive FIFO Not Empty */
 #define SSSR_BSY	(1 << 4)	/* SSP Busy */
@@ -160,6 +161,7 @@ enum pxa_ssp_type {
 	PXA25x_NSSP, /* pxa 255, 26x (including ASSP) */
 	PXA27x_SSP,
 	PXA168_SSP,
+	CE4100_SSP,
 };
 
 struct ssp_device {
-- 
cgit v1.2.3-55-g7522


From 579d3bb2ac1a351bbf536480a9ab38199bbf901d Mon Sep 17 00:00:00 2001
From: Sebastian Andrzej Siewior
Date: Mon, 22 Nov 2010 17:12:17 -0800
Subject: spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX
 bytes.

After all TX bytes are sent, the driver spins while the SPI core is busy
and then it spins for a "short" period of time until RX bytes are
available.
On Sodavile the busy flag disappears pretty quick and after that it
takes approx ~130ms (sometimes less but not much) until there are bytes
available in the RX FIFO.
This patch removes the busy loop and modifies the RX threshould so we
get woken up once the remainings bytes arrived.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
---
 drivers/spi/pxa2xx_spi.c | 56 +++++++++++++++++++++++++++++++++---------------
 1 file changed, 39 insertions(+), 17 deletions(-)

(limited to 'drivers')

diff --git a/drivers/spi/pxa2xx_spi.c b/drivers/spi/pxa2xx_spi.c
index a54685bb7e53..9ca6454cfadc 100644
--- a/drivers/spi/pxa2xx_spi.c
+++ b/drivers/spi/pxa2xx_spi.c
@@ -660,13 +660,25 @@ static irqreturn_t dma_transfer(struct driver_data *drv_data)
 	return IRQ_NONE;
 }
 
+static void reset_sccr1(struct driver_data *drv_data)
+{
+	void __iomem *reg = drv_data->ioaddr;
+	struct chip_data *chip = drv_data->cur_chip;
+	u32 sccr1_reg;
+
+	sccr1_reg = read_SSCR1(reg) & ~drv_data->int_cr1;
+	sccr1_reg &= ~SSCR1_RFT;
+	sccr1_reg |= chip->threshold;
+	write_SSCR1(sccr1_reg, reg);
+}
+
 static void int_error_stop(struct driver_data *drv_data, const char* msg)
 {
 	void __iomem *reg = drv_data->ioaddr;
 
 	/* Stop and reset SSP */
 	write_SSSR_CS(drv_data, drv_data->clear_sr);
-	write_SSCR1(read_SSCR1(reg) & ~drv_data->int_cr1, reg);
+	reset_sccr1(drv_data);
 	if (!pxa25x_ssp_comp(drv_data))
 		write_SSTO(0, reg);
 	flush(drv_data);
@@ -684,7 +696,7 @@ static void int_transfer_complete(struct driver_data *drv_data)
 
 	/* Stop SSP */
 	write_SSSR_CS(drv_data, drv_data->clear_sr);
-	write_SSCR1(read_SSCR1(reg) & ~drv_data->int_cr1, reg);
+	reset_sccr1(drv_data);
 	if (!pxa25x_ssp_comp(drv_data))
 		write_SSTO(0, reg);
 
@@ -739,24 +751,34 @@ static irqreturn_t interrupt_transfer(struct driver_data *drv_data)
 	}
 
 	if (drv_data->tx == drv_data->tx_end) {
-		write_SSCR1(read_SSCR1(reg) & ~SSCR1_TIE, reg);
-		/* PXA25x_SSP has no timeout, read trailing bytes */
+		u32 bytes_left;
+		u32 sccr1_reg;
+
+		sccr1_reg = read_SSCR1(reg);
+		sccr1_reg &= ~SSCR1_TIE;
+
+		/*
+		 * PXA25x_SSP has no timeout, set up rx threshould for the
+		 * remaing RX bytes.
+		 */
 		if (pxa25x_ssp_comp(drv_data)) {
-			if (!wait_ssp_rx_stall(reg))
-			{
-				int_error_stop(drv_data, "interrupt_transfer: "
-						"rx stall failed");
-				return IRQ_HANDLED;
-			}
-			if (!drv_data->read(drv_data))
-			{
-				int_error_stop(drv_data,
-						"interrupt_transfer: "
-						"trailing byte read failed");
-				return IRQ_HANDLED;
+
+			sccr1_reg &= ~SSCR1_RFT;
+
+			bytes_left = drv_data->rx_end - drv_data->rx;
+			switch (drv_data->n_bytes) {
+			case 4:
+				bytes_left >>= 1;
+			case 2:
+				bytes_left >>= 1;
 			}
-			int_transfer_complete(drv_data);
+
+			if (bytes_left > RX_THRESH_DFLT)
+				bytes_left = RX_THRESH_DFLT;
+
+			sccr1_reg |= SSCR1_RxTresh(bytes_left);
 		}
+		write_SSCR1(sccr1_reg, reg);
 	}
 
 	/* We did something */
-- 
cgit v1.2.3-55-g7522


From 21486af0f34d03b813b023d7a2b887b329f60486 Mon Sep 17 00:00:00 2001
From: Sebastian Andrzej Siewior
Date: Fri, 8 Oct 2010 18:11:19 +0200
Subject: spi/pxa2xx: pass of_node to spi device and set a parent device

the of_node will auto-publish devices which are added to the device
tree.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
---
 drivers/spi/pxa2xx_spi.c | 4 ++++
 1 file changed, 4 insertions(+)

(limited to 'drivers')

diff --git a/drivers/spi/pxa2xx_spi.c b/drivers/spi/pxa2xx_spi.c
index 9ca6454cfadc..95928833855b 100644
--- a/drivers/spi/pxa2xx_spi.c
+++ b/drivers/spi/pxa2xx_spi.c
@@ -1556,6 +1556,10 @@ static int __devinit pxa2xx_spi_probe(struct platform_device *pdev)
 	drv_data->pdev = pdev;
 	drv_data->ssp = ssp;
 
+	master->dev.parent = &pdev->dev;
+#ifdef CONFIG_OF
+	master->dev.of_node = pdev->dev.of_node;
+#endif
 	/* the spi->mode bits understood by this driver: */
 	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
 
-- 
cgit v1.2.3-55-g7522