blob: 5019f5182bf415eb0c1e600bdbc66dd95cb5781e (
plain) (
blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
|
IBM ServeRAID driver Change Log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
5.00.01 - Sarasota ( 5i ) adapters must always be scanned first
- Get rid on IOCTL_NEW_COMMAND code
- Add Extended DCDB Commands for Tape Support in 5I
4.90.11 - Don't actually RESET unless it's physically required
- Remove unused compile options
4.90.08 - Data Corruption if First Scatter Gather Element is > 64K
4.90.08 - Increase Delays in Flashing ( Trombone Only - 4H )
4.90.05 - Use New PCI Architecture to facilitate Hot Plug Development
4.90.01 - Add ServeRAID Version Checking
4.80.26 - Clean up potential code problems ( Arjan's recommendations )
4.80.21 - Change memcpy() to copy_to_user() in NVRAM Page 5 IOCTL path
4.80.20 - Set max_sectors in Scsi_Host structure ( if >= 2.4.7 kernel )
- 5 second delay needed after resetting an i960 adapter
4.80.14 - Take all semaphores off stack
- Clean Up New_IOCTL path
4.80.04 - Eliminate calls to strtok() if 2.4.x or greater
- Adjustments to Device Queue Depth
4.80.00 - Make ia64 Safe
4.72.01 - I/O Mapped Memory release ( so "insmod ips" does not Fail )
- Don't Issue Internal FFDC Command if there are Active Commands
- Close Window for getting too many IOCTL's active
4.72.00 - Allow for a Scatter-Gather Element to exceed MAX_XFER Size
4.71.00 - Change all memory allocations to not use GFP_DMA flag
- Code Clean-Up for 2.4.x kernel
4.70.15 - Fix Breakup for very large ( non-SG ) requests
4.70.13 - Don't release HA Lock in ips_next() until SC taken off queue
- Unregister SCSI device in ips_release()
- Don't Send CDB's if we already know the device is not present
4.70.12 - Corrective actions for bad controller ( during initialization )
4.70.09 - Use a Common ( Large Buffer ) for Flashing from the JCRM CD
- Add IPSSEND Flash Support
- Set Sense Data for Unknown SCSI Command
- Use Slot Number from NVRAM Page 5
- Restore caller's DCDB Structure
4.20.14 - Update patch files for kernel 2.4.0-test5
4.20.13 - Fix some failure cases / reset code
- Hook into the reboot_notifier to flush the controller
cache
4.20.03 - Rename version to coincide with new release schedules
- Performance fixes
- Fix truncation of /proc files with cat
- Merge in changes through kernel 2.4.0test1ac21
4.10.13 - Fix for dynamic unload and proc file system
4.10.00 - Add support for ServeRAID 4M/4L
4.00.06 - Fix timeout with initial FFDC command
4.00.05 - Remove wish_block from init routine
- Use linux/spinlock.h instead of asm/spinlock.h for kernels
2.3.18 and later
- Sync with other changes from the 2.3 kernels
4.00.04 - Rename structures/constants to be prefixed with IPS_
4.00.03 - Add alternative passthru interface
- Add ability to flash ServeRAID BIOS
4.00.02 - Fix problem with PT DCDB with no buffer
4.00.01 - Add support for First Failure Data Capture
4.00.00 - Add support for ServeRAID 4
3.60.02 - Make DCDB direction based on lookup table.
- Only allow one DCDB command to a SCSI ID at a time.
3.60.01 - Remove bogus error check in passthru routine.
3.60.00 - Bump max commands to 128 for use with ServeRAID
firmware 3.60.
- Change version to 3.60 to coincide with ServeRAID release
numbering.
1.00.00 - Initial Public Release
- Functionally equivalent to 0.99.05
0.99.05 - Fix an oops on certain passthru commands
0.99.04 - Fix race condition in the passthru mechanism
-- this required the interface to the utilities to change
- Fix error recovery code
0.99.03 - Make interrupt routine handle all completed request on the
adapter not just the first one
- Make sure passthru commands get woken up if we run out of
SCBs
- Send all of the commands on the queue at once rather than
one at a time since the card will support it.
0.99.02 - Added some additional debug statements to print out
errors if an error occurs while trying to read/write
to a logical drive (IPS_DEBUG).
- Fixed read/write errors when the adapter is using an
8K stripe size.
|
