summaryrefslogtreecommitdiffstats
path: root/tcg/mips
Commit message (Collapse)AuthorAgeFilesLines
...
* tcg-mips: Add mips64 opcodesJin Guojie2017-01-061-75/+118
| | | | | | | | | | | | | Since the mips manual tables are in octal, reorg all of the opcodes into that format for clarity. Note that the 64-bit opcodes are as yet unused. Tested-by: Aurelien Jarno <aurelien@aurel32.net> Tested-by: James Hogan <james.hogan@imgtec.com> Tested-by: YunQiang Su <wzssyqa@gmail.com> Signed-off-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Jin Guojie <jinguojie@loongson.cn> Message-Id: <1483592275-4496-3-git-send-email-jinguojie@loongson.cn>
* tcg-mips: Move bswap code to a subroutineJin Guojie2017-01-062-70/+139
| | | | | | | | | | | | | | | | Without the mips32r2 instructions to perform swapping, bswap is quite large, dominating the size of each reverse-endian qemu_ld/qemu_st operation. Create a subroutine in the prologue block. The subroutine requires extra reserved registers (TCG_TMP[2, 3]). Using these within qemu_ld means that we need not place additional restrictions on the qemu_ld outputs. Tested-by: Aurelien Jarno <aurelien@aurel32.net> Tested-by: James Hogan <james.hogan@imgtec.com> Tested-by: YunQiang Su <wzssyqa@gmail.com> Signed-off-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Jin Guojie <jinguojie@loongson.cn> Message-Id: <1483592275-4496-2-git-send-email-jinguojie@loongson.cn>
* tcg/mips: Add support for fencePranith Kumar2016-09-161-0/+30
| | | | | | Signed-off-by: Pranith Kumar <bobby.prani@gmail.com> Message-Id: <20160714202026.9727-7-bobby.prani@gmail.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg: Support arbitrary size + alignmentRichard Henderson2016-09-161-2/+9
| | | | | | | | | | | Previously we allowed fully unaligned operations, but not operations that are aligned but with less alignment than the operation size. In addition, arm32, ia64, mips, and sparc had been omitted from the previous overalignment patch, which would have led to that alignment being enforced. Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg: Clean up tcg-target.h header guardsMarkus Armbruster2016-07-121-2/+3
| | | | | | | | | | | | | These use guard symbols like TCG_TARGET_$target. scripts/clean-header-guards.pl doesn't like them because they don't match their file name (they should, to make guard collisions less likely). Clean them up: use guard symbol $target_TCG_TARGET_H for tcg/$target/tcg-target.h. Signed-off-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Richard Henderson <rth@twiddle.net>
* tcg: Optimize spills of constantsRichard Henderson2016-07-061-0/+10
| | | | | | | | | | | While we can store constants via constrants on INDEX_op_st_i32 et al, we weren't able to spill constants to backing store. Add a new backend interface, tcg_out_sti, which may store the constant (and is allowed to fail). Rearrange the temp_* helpers so that we only attempt to directly store a constant when the temp is becoming dead/free. Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg: Clean up direct block chaining data fieldsSergey Fedorov2016-05-131-4/+4
| | | | | | | | | | | | | | | | | | | | | | Briefly describe in a comment how direct block chaining is done. It should help in understanding of the following data fields. Rename some fields in TranslationBlock and TCGContext structures to better reflect their purpose (dropping excessive 'tb_' prefix in TranslationBlock but keeping it in TCGContext): tb_next_offset => jmp_reset_offset tb_jmp_offset => jmp_insn_offset tb_next => jmp_target_addr jmp_next => jmp_list_next jmp_first => jmp_list_first Avoid using a magic constant as an invalid offset which is used to indicate that there's no n-th jump generated. Signed-off-by: Sergey Fedorov <serge.fdrv@gmail.com> Signed-off-by: Sergey Fedorov <sergey.fedorov@linaro.org> Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg/mips: Make direct jump patching thread-safeSergey Fedorov2016-05-131-2/+1Star
| | | | | | | | | | | | | Ensure direct jump patching in MIPS is atomic by using atomic_read()/atomic_set() for code patching. Signed-off-by: Sergey Fedorov <serge.fdrv@gmail.com> Signed-off-by: Sergey Fedorov <sergey.fedorov@linaro.org> Message-Id: <1461341333-19646-11-git-send-email-sergey.fedorov@linaro.org> Signed-off-by: Richard Henderson <rth@twiddle.net> [rth: Merged the deposit32 followup.] [rth: Merged the following followup.] Message-Id: <1462210518-26522-1-git-send-email-sergey.fedorov@linaro.org>
* tcg: check for CONFIG_DEBUG_TCG instead of NDEBUGAurelien Jarno2016-04-211-1/+1
| | | | | | | | | | Check for CONFIG_DEBUG_TCG instead of NDEBUG, drop now useless code. Cc: Richard Henderson <rth@twiddle.net> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net> Message-id: 1461228530-14852-2-git-send-email-aurelien@aurel32.net Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* tcg: use tcg_debug_assert instead of assert (fix performance regression)Aurelien Jarno2016-04-211-9/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TCG code is quite performance sensitive, but at the same time can also be quite tricky. That is why asserts that can be enabled with the --enable-debug-tcg configure option. This used to work the following way: | #include "config.h" | | ... | | #if !defined(CONFIG_DEBUG_TCG) && !defined(NDEBUG) | /* define it to suppress various consistency checks (faster) */ | #define NDEBUG | #endif | | ... | | #include <assert.h> Since commit 757e725b (tcg: Clean up includes) "config.h" as been replaced by "qemu/osdep.h" which itself includes <assert.h>. As a consequence the assertions are always enabled, even when using --disable-debug-tcg, causing a performance regression, especially on targets with many registers. For instance on qemu-system-ppc the speed difference is about 15%. tcg_debug_assert is controlled directly by CONFIG_DEBUG_TCG and already uses in some places. This patch replaces all the calls to assert into calss to tcg_debug_assert. Cc: Peter Maydell <peter.maydell@linaro.org> Cc: Richard Henderson <rth@twiddle.net> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net> Message-id: 1461228530-14852-1-git-send-email-aurelien@aurel32.net Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* tcg/mips: Fix type of tcg_target_reg_alloc_order[]James Hogan2016-04-051-1/+1
| | | | | | | | | | | | | | | | | | | | The MIPS TCG backend is the only one to have tcg_target_reg_alloc_order[] elements of type TCGReg rather than int. This resulted in commit 91478cefaaf2 ("tcg: Allocate indirect_base temporaries in a different order") breaking the build on MIPS since the type differed from indirect_reg_alloc_order[]: tcg/tcg.c:1725:44: error: pointer type mismatch in conditional expression [-Werror] order = rev ? indirect_reg_alloc_order : tcg_target_reg_alloc_order; ^ Make it an array of ints to fix the build and match other architectures. Fixes: 91478cefaaf2 ("tcg: Allocate indirect_base temporaries in a different order") Signed-off-by: James Hogan <james.hogan@imgtec.com> Acked-by: Aurelien Jarno <aurelien@aurel32.net> Message-Id: <1459522179-6584-1-git-send-email-james.hogan@imgtec.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg: Remove unnecessary osdep.h includes from tcg-target.inc.cPeter Maydell2016-02-231-1/+0Star
| | | | | | | | | | | | | | Commit 757e725b58c57d added a number of #include "qemu/osdep.h" files to the tcg-target.c files (as they were named at the time). These are unnecessary because these files are not standalone C files, and the tcg/tcg.c file which includes them will have already included osdep.h on their behalf. Remove the unneeded include directives. Reviewed-by: Eric Blake <eblake@redhat.com> Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Message-Id: <1456238983-10160-4-git-send-email-peter.maydell@linaro.org> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg: Rename tcg-target.c to tcg-target.inc.cPeter Maydell2016-02-231-0/+0
| | | | | | | | | | | Rename the per-architecture tcg-target.c files to tcg-target.inc.c. This makes it clearer that they are not intended to be standalone C files, but are instead #included into another source file. Reviewed-by: Eric Blake <eblake@redhat.com> Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Message-Id: <1456238983-10160-2-git-send-email-peter.maydell@linaro.org> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg: Clean up includesPeter Maydell2016-01-291-1/+1
| | | | | | | | | | Clean up includes so that osdep.h is included first and headers which it implies are not included manually. This commit was created with scripts/clean-includes. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 1453832250-766-16-git-send-email-peter.maydell@linaro.org
* tcg/mips: Support r6 SEL{NE, EQ}Z instead of MOVN/MOVZJames Hogan2015-10-191-6/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Extend MIPS movcond implementation to support the SELNEZ/SELEQZ instructions introduced in MIPS r6 (where MOVN/MOVZ have been removed). Whereas the "MOVN/MOVZ rd, rs, rt" instructions have the following semantics: rd = [!]rt ? rs : rd The "SELNEZ/SELEQZ rd, rs, rt" instructions are slightly different: rd = [!]rt ? rs : 0 First we ensure that if one of the movcond input values is zero that it comes last (we can swap the input arguments if we invert the condition). This is so that it can exactly match one of the SELNEZ/SELEQZ instructions and avoid the need to emit the other one. Otherwise we emit the opposite instruction first into a temporary register, and OR that into the result: SELNEZ/SELEQZ TMP1, v2, c1 SELEQZ/SELNEZ ret, v1, c1 OR ret, ret, TMP1 Which does the following: ret = cond ? v1 : v2 Reviewed-by: Aurelien Jarno <aurelien@aurel32.net> Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Richard Henderson <rth@twiddle.net> Message-Id: <1443788657-14537-7-git-send-email-james.hogan@imgtec.com>
* tcg/mips: Support r6 multiply/divide encodingsJames Hogan2015-10-192-3/+43
| | | | | | | | | | | | | | | | | | | | | | | MIPSr6 adds several new integer multiply, divide, and modulo instructions, and removes several pre-r6 encodings, along with the HI/LO registers which were the implicit operands of some of those instructions. Update TCG to use the new instructions when built for r6. The new instructions actually map much more directly to the TCG ops, as they only provide a single 32-bit half of the result and in a normal general purpose register instead of HI or LO. The mulu2_i32 and muls2_i32 operations are no longer appropriate for r6, so they are removed from the TCG opcode table. This is because they would need to emit two separate host instructions anyway (for the high and low half of the result), which TCG can arrange automatically for us in the absense of mulu2_i32/muls2_i32 by splitting it into mul_i32 and mul*h_i32 TCG ops. Reviewed-by: Aurelien Jarno <aurelien@aurel32.net> Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Richard Henderson <rth@twiddle.net> Message-Id: <1443788657-14537-6-git-send-email-james.hogan@imgtec.com>
* tcg/mips: Support r6 JR encodingJames Hogan2015-10-191-1/+4
| | | | | | | | | | | | | | | MIPSr6 encodes JR as JALR with zero as the link register, and the pre-r6 JR encoding is removed. Update TCG to use the new encoding when built for r6. We still use the old encoding for pre-r6, so as not to confuse return prediction stack hardware which may detect only particular encodings of the return instruction. Reviewed-by: Aurelien Jarno <aurelien@aurel32.net> Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Richard Henderson <rth@twiddle.net> Message-Id: <1443788657-14537-5-git-send-email-james.hogan@imgtec.com>
* tcg/mips: Add use_mips32r6_instructions definitionJames Hogan2015-10-191-0/+7
| | | | | | | | | | | Add definition use_mips32r6_instructions to the MIPS TCG backend which is constant 1 when built for MIPS release 6. This will be used to decide between pre-R6 and R6 instruction encodings. Reviewed-by: Aurelien Jarno <aurelien@aurel32.net> Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Richard Henderson <rth@twiddle.net> Message-Id: <1443788657-14537-4-git-send-email-james.hogan@imgtec.com>
* tcg/mips: pass oi to tcg_out_tlb_loadAurelien Jarno2015-09-191-15/+5Star
| | | | | | | | | | Instead of computing mem_index and s_bits in both tcg_out_qemu_ld and tcg_out_qemu_st function and passing them to tcg_out_tlb_load, directly pass oi to the tcg_out_tlb_load function and compute mem_index and s_bits there. Reviewed-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
* tcg/mips: move tcg_out_addsub2Aurelien Jarno2015-09-191-49/+49
| | | | | | | | | Somehow the tcg_out_addsub2 function ended-up in the middle of the qemu_ld/st related functions. Move it with other arithmetics related functions. Reviewed-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
* tcg/mips: Fix clobbering of qemu_ld inputsJames Hogan2015-09-191-11/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MIPS TCG backend implements qemu_ld with 64-bit targets using the v0 register (base) as a temporary to load the upper half of the QEMU TLB comparator (see line 5 below), however this happens before the input address is used (line 8 to mask off the low bits for the TLB comparison, and line 12 to add the host-guest offset). If the input address (addrl) also happens to have been placed in v0 (as in the second column below), it gets clobbered before it is used. addrl in t2 addrl in v0 1 srl a0,t2,0x7 srl a0,v0,0x7 2 andi a0,a0,0x1fe0 andi a0,a0,0x1fe0 3 addu a0,a0,s0 addu a0,a0,s0 4 lw at,9136(a0) lw at,9136(a0) set TCG_TMP0 (at) 5 lw v0,9140(a0) lw v0,9140(a0) set base (v0) 6 li t9,-4093 li t9,-4093 7 lw a0,9160(a0) lw a0,9160(a0) set addend (a0) 8 and t9,t9,t2 and t9,t9,v0 use addrl 9 bne at,t9,0x836d8c8 bne at,t9,0x836d838 use TCG_TMP0 10 nop nop 11 bne v0,t8,0x836d8c8 bne v0,a1,0x836d838 use base 12 addu v0,a0,t2 addu v0,a0,v0 use addrl, addend 13 lw t0,0(v0) lw t0,0(v0) Fix by using TCG_TMP0 (at) as the temporary instead of v0 (base), pushing the load on line 5 forward into the delay slot of the low comparison (line 10). The early load of the addend on line 7 also needs pushing even further for 64-bit targets, or it will clobber a0 before we're done with it. The output for 32-bit targets is unaffected. srl a0,v0,0x7 andi a0,a0,0x1fe0 addu a0,a0,s0 lw at,9136(a0) -lw v0,9140(a0) load high comparator li t9,-4093 -lw a0,9160(a0) load addend and t9,t9,v0 bne at,t9,0x836d838 - nop + lw at,9140(a0) load high comparator +lw a0,9160(a0) load addend -bne v0,a1,0x836d838 +bne at,a1,0x836d838 addu v0,a0,v0 lw t0,0(v0) Cc: qemu-stable@nongnu.org Reviewed-by: Richard Henderson <rth@twiddle.net> Reviewed-by: Aurelien Jarno <aurelien@aurel32.net> Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
* linux-user: remove useless macros GUEST_BASE and RESERVED_VALaurent Vivier2015-08-241-8/+8
| | | | | | | | | | | As we have removed CONFIG_USE_GUEST_BASE, we always use a guest base and the macros GUEST_BASE and RESERVED_VA become useless: replace them by their values. Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Laurent Vivier <laurent@vivier.eu> Message-Id: <1440420834-8388-1-git-send-email-laurent@vivier.eu> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg/mips: fix add2Aurelien Jarno2015-08-011-0/+3
| | | | | | | | | | | | | | The add2 code in the tcg_out_addsub2 function doesn't take into account the case where rl == al == bl. In that case we can't compute the carry after the addition. As it corresponds to a multiplication by 2, the carry bit is the bit 31. While this is a corner case, this prevents x86-64 guests to boot on a MIPS host. Cc: qemu-stable@nongnu.org Reviewed-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
* tcg/mips: Mask TCGMemOp appropriately for indexingAurelien Jarno2015-08-011-2/+2
| | | | | | | | Commit 2b7ec66f fixed TCGMemOp masking following the MO_AMASK addition, but two cases were forgotten in the TCG MIPS backend. Reviewed-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
* tcg/mips: fix TLB loading for BE host with 32-bit guestsAurelien Jarno2015-08-011-1/+3
| | | | | | | | | | For 32-bit guest, we load a 32-bit address from the TLB, so there is no need to compensate for the low or high part. This fixes 32-bit guests on big-endian hosts. Cc: qemu-stable@nongnu.org Reviewed-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
* tcg/mips: Fix build error from merged memop+mmu_idx parameterJames Hogan2015-07-091-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | Commit 3972ef6f830d ("tcg: Push merged memop+mmu_idx parameter to softmmu routines") caused the following build errors when building TCG for MIPS: In file included from tcg/tcg.c:258:0: tcg/mips/tcg-target.c In function ‘tcg_out_qemu_ld_slow_path’: tcg/mips/tcg-target.c:1015:22: error: ‘lb’ undeclared (first use in this function) tcg/mips/tcg-target.c In function ‘tcg_out_qemu_st_slow_path’: tcg/mips/tcg-target.c:1058:22: error: ‘lb’ undeclared (first use in this function) It looks like lb was meant to refer to the TCGLabelQemuLdst *l parameter, so fix both references to lb to refer to just l. Fixes: 3972ef6f830d ("tcg: Push merged memop+mmu_idx parameter to softmmu routines") Signed-off-by: James Hogan <james.hogan@imgtec.com> Reviewed-by: Leon Alrae <leon.alrae@imgtec.com> Message-id: 1436433435-24898-2-git-send-email-james.hogan@imgtec.com Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: Leon Alrae <leon.alrae@imgtec.com> Cc: Richard Henderson <rth@twiddle.net> Cc: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* tcg: Mask TCGMemOp appropriately for indexingRichard Henderson2015-06-091-2/+2
| | | | | | | | | | The addition of MO_AMASK means that places that used inverted masks need to be changed to use positive masks, and places that failed to mask the intended bits need updating. Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com> Tested-by: Yongbok Kim <yongbok.kim@imgtec.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg: add TCG_TARGET_TLB_DISPLACEMENT_BITSPaolo Bonzini2015-06-031-0/+1
| | | | | | | | | | | | This will be used to size the TLB when more than 8 MMU modes are used by the target. Limitations come from the limited size of the immediate fields (which sometimes, as in the case of Aarch64, extend to instructions that shift the immediate). Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Message-Id: <1424436345-37924-2-git-send-email-pbonzini@redhat.com> Reviewed-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Alexander Graf <agraf@suse.de>
* tcg: Push merged memop+mmu_idx parameter to softmmu routinesRichard Henderson2015-05-141-13/+13
| | | | | | | | The extra information is not yet used but it is now available. This requires minor changes through all of the tcg backends. Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg: Merge memop and mmu_idx parameters to qemu_ld/stRichard Henderson2015-05-141-4/+8
| | | | | | | | | At the tcg opcode level, not at the tcg-op.h generator level. This requires minor changes through all of the tcg backends, but none of the cpu translators. Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg: Change generator-side labels to a pointerRichard Henderson2015-03-131-9/+8Star
| | | | | | | | | | | | | | | This is less about improved type checking than enabling a subsequent change to the representation of labels. Acked-by: Claudio Fontana <claudio.fontana@huawei.com> Tested-by: Claudio Fontana <claudio.fontana@huawei.com> Cc: Andrzej Zaborowski <balrogg@gmail.com> Cc: Peter Maydell <peter.maydell@linaro.org> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: Blue Swirl <blauwirbel@gmail.com> Cc: Stefan Weil <sw@weilnetz.de> Reviewed-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg/mips: fix store softmmu slow pathAurelien Jarno2014-11-021-1/+1
| | | | | | | | | | | | Commit 9d8bf2d1 moved the softmmu slow path out of line and introduce a regression at the same time by always calling tcg_out_tlb_load with is_load=1. This makes impossible to run any significant code under qemu-system-mips*. Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: qemu-stable@nongnu.org Reviewed-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
* Fix new typos (found by codespell)Stefan Weil2014-06-241-2/+2
| | | | | | | | | | | | * accomodate -> accommodate * aquiring -> acquiring * beacuse -> because * loosing -> losing * prefering -> preferring * threshhold -> threshold Signed-off-by: Stefan Weil <sw@weilnetz.de> Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
* tcg: Remove TCG_TARGET_HAS_new_ldstRichard Henderson2014-06-041-2/+0Star
| | | | | | | Since all backends have been converted, remove the compatibility code. Acked-by: Claudio Fontana <claudio.fontana@huawei.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg-mips: Enable direct chaining of TBsRichard Henderson2014-05-241-1/+10
| | | | | | | | Now that the code_gen_buffer is constrained to not cross 256mb regions, we are assured that we can use J to reach another TB. Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg-mips: Simplify movcondRichard Henderson2014-05-241-49/+17Star
| | | | | | | Use the same table to fold comparisons as with setcond. Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg-mips: Simplify brcond2Richard Henderson2014-05-241-57/+20Star
| | | | | | | | Emitting a single branch instead of (up to) 3, using setcond2 to generate the composite compare. Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg-mips: Improve setcond eq/ne vs zerosRichard Henderson2014-05-241-4/+36
| | | | | | | | | The original code results in one too many insns per zero present in the input. And since comparing 64-bit numbers vs zero is common... Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg-mips: Simplify setcond2Richard Henderson2014-05-241-64/+31Star
| | | | | | | | Using tcg_unsigned_cond and tcg_high_cond. Also, move the function up in the file for future cleanups. Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg-mips: Simplify brcondRichard Henderson2014-05-241-46/+41Star
| | | | | | | Use the same table to fold comparisons as with setcond. Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg-mips: Simplify setcondRichard Henderson2014-05-241-58/+67
| | | | | | | | Use a table to fold comparisons to less-than. Also, move the function up in the file for futher simplifications. Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg-mips: Commonize opcode implementationsRichard Henderson2014-05-241-114/+98Star
| | | | | | | Most opcodes fall in to one of a couple of patterns. Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg-mips: Improve add2/sub2Richard Henderson2014-05-241-31/+56
| | | | | | | Reduce insn count from 5 to either 3 or 4. Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg-mips: Hoist args loadsRichard Henderson2014-05-241-98/+103
| | | | | Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg-mips: Fix subtract immediate rangeRichard Henderson2014-05-241-5/+11
| | | | | | | | Since we must use ADDUI, we would generate incorrect code for -32768. Leaving off subtract of +32768 makes things easier for a follow-on patch. Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg-mips: Name the opcode enumerationRichard Henderson2014-05-241-9/+9
| | | | | | | And use it in the opcode emission functions. Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg-mips: Use EXT for AND on mips32r2Richard Henderson2014-05-242-14/+50
| | | | | | | At the same time, tidy deposit by introducing tcg_out_opc_bf. Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg-mips: Use T9 for TCG_TMP1Richard Henderson2014-05-241-1/+1
| | | | | | | | | T0 is an argument register for the n32 and n64 abis. T9 is the call address register for the abis, and is more directly under the control of the backend. Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg-mips: Introduce TCG_TMP0, TCG_TMP1Richard Henderson2014-05-241-114/+117
| | | | | | | Use these instead of hard-coding the registers to use for temporaries. Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
* tcg-mips: Rearrange register allocationRichard Henderson2014-05-242-11/+19
| | | | | | | | | | | | Use FP (also known as S8) as a normal call-saved register. Include T0 in the allocation order and call-clobbered list even though it's currently used as a TCG temporary. Put the argument registers at the end of the allocation order. Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Richard Henderson <rth@twiddle.net>
generated by cgit v1.2.3-55-g7522 (git 2.39.0) at 2024-12-22 14:47:37 +0100