diff options
Diffstat (limited to 'memtestEDK/Memtest/SingleComponents/serial.h')
| -rw-r--r-- | memtestEDK/Memtest/SingleComponents/serial.h | 162 |
1 files changed, 162 insertions, 0 deletions
diff --git a/memtestEDK/Memtest/SingleComponents/serial.h b/memtestEDK/Memtest/SingleComponents/serial.h new file mode 100644 index 0000000..bbdfa9c --- /dev/null +++ b/memtestEDK/Memtest/SingleComponents/serial.h @@ -0,0 +1,162 @@ +/* + * include/linux/serial.h + * + * Copyright (C) 1992, 1994 by Theodore Ts'o. + * + * Redistribution of this file is permitted under the terms of the GNU + * Public License (GPL) + * + * These are the UART port assignments, expressed as offsets from the base + * register. These assignments should hold for any serial port based on + * a 8250, 16450, or 16550(A). + */ + +#ifndef _LINUX_SERIAL_REG_H +#define _LINUX_SERIAL_REG_H + +#define UART_RX 0 /* In: Receive buffer (DLAB=0) */ +#define UART_TX 0 /* Out: Transmit buffer (DLAB=0) */ +#define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */ +#define UART_DLM 1 /* Out: Divisor Latch High (DLAB=1) */ +#define UART_IER 1 /* Out: Interrupt Enable Register */ +#define UART_IIR 2 /* In: Interrupt ID Register */ +#define UART_FCR 2 /* Out: FIFO Control Register */ +#define UART_EFR 2 /* I/O: Extended Features Register */ + /* (DLAB=1, 16C660 only) */ +#define UART_LCR 3 /* Out: Line Control Register */ +#define UART_MCR 4 /* Out: Modem Control Register */ +#define UART_LSR 5 /* In: Line Status Register */ +#define UART_MSR 6 /* In: Modem Status Register */ +#define UART_SCR 7 /* I/O: Scratch Register */ + + + +/* + * These are the definitions for the FIFO Control Register + * (16650 only) + */ +#define UART_FCR_ENABLE_FIFO 0x01 /* Enable the FIFO */ +#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */ +#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */ +#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */ +#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */ +#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */ +#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */ +#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */ +#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */ +/* 16650 redefinitions */ +#define UART_FCR6_R_TRIGGER_8 0x00 /* Mask for receive trigger set at 1 */ +#define UART_FCR6_R_TRIGGER_16 0x40 /* Mask for receive trigger set at 4 */ +#define UART_FCR6_R_TRIGGER_24 0x80 /* Mask for receive trigger set at 8 */ +#define UART_FCR6_R_TRIGGER_28 0xC0 /* Mask for receive trigger set at 14 */ +#define UART_FCR6_T_TRIGGER_16 0x00 /* Mask for transmit trigger set at 16 */ +#define UART_FCR6_T_TRIGGER_8 0x10 /* Mask for transmit trigger set at 8 */ +#define UART_FCR6_T_TRIGGER_24 0x20 /* Mask for transmit trigger set at 24 */ +#define UART_FCR6_T_TRIGGER_30 0x30 /* Mask for transmit trigger set at 30 */ + +/* + * These are the definitions for the Line Control Register + * + * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting + * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits. + */ +#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */ +#define UART_LCR_SBC 0x40 /* Set break control */ +#define UART_LCR_SPAR 0x20 /* Stick parity (?) */ +#define UART_LCR_EPAR 0x10 /* Even parity select */ +#define UART_LCR_PARITY 0x08 /* Parity Enable */ +#define UART_LCR_STOP 0x04 /* Stop bits: 0=1 stop bit, 1= 2 stop bits */ +#define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */ +#define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */ +#define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */ +#define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */ + +/* + * These are the definitions for the Line Status Register + */ +#define UART_LSR_TEMT 0x40 /* Transmitter empty */ +#define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */ +#define UART_LSR_BI 0x10 /* Break interrupt indicator */ +#define UART_LSR_FE 0x08 /* Frame error indicator */ +#define UART_LSR_PE 0x04 /* Parity error indicator */ +#define UART_LSR_OE 0x02 /* Overrun error indicator */ +#define UART_LSR_DR 0x01 /* Receiver data ready */ + +/* + * These are the definitions for the Interrupt Identification Register + */ +#define UART_IIR_NO_INT 0x01 /* No interrupts pending */ +#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */ + +#define UART_IIR_MSI 0x00 /* Modem status interrupt */ +#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */ +#define UART_IIR_RDI 0x04 /* Receiver data interrupt */ +#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */ + +/* + * These are the definitions for the Interrupt Enable Register + */ +#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */ +#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */ +#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */ +#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */ + +/* + * These are the definitions for the Modem Control Register + */ +#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */ +#define UART_MCR_OUT2 0x08 /* Out2 complement */ +#define UART_MCR_OUT1 0x04 /* Out1 complement */ +#define UART_MCR_RTS 0x02 /* RTS complement */ +#define UART_MCR_DTR 0x01 /* DTR complement */ + +/* + * These are the definitions for the Modem Status Register + */ +#define UART_MSR_DCD 0x80 /* Data Carrier Detect */ +#define UART_MSR_RI 0x40 /* Ring Indicator */ +#define UART_MSR_DSR 0x20 /* Data Set Ready */ +#define UART_MSR_CTS 0x10 /* Clear to Send */ +#define UART_MSR_DDCD 0x08 /* Delta DCD */ +#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */ +#define UART_MSR_DDSR 0x02 /* Delta DSR */ +#define UART_MSR_DCTS 0x01 /* Delta CTS */ +#define UART_MSR_ANY_DELTA 0x0F /* Any of the delta bits! */ + +/* + * These are the definitions for the Extended Features Register + * (StarTech 16C660 only, when DLAB=1) + */ +#define UART_EFR_CTS 0x80 /* CTS flow control */ +#define UART_EFR_RTS 0x40 /* RTS flow control */ +#define UART_EFR_SCD 0x20 /* Special character detect */ +#define UART_EFR_ENI 0x10 /* Enhanced Interrupt */ +/* + * the low four bits control software flow control + */ + +#define serial_echo_outb(v,a) outb((v),(a)+serial_base_ports[serial_tty]) +#define serial_echo_inb(a) inb((a)+serial_base_ports[serial_tty]) +#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) +/* Wait for transmitter & holding register to empty */ +#define WAIT_FOR_XMITR \ + do { \ + lsr = serial_echo_inb(UART_LSR); \ + } while ((lsr & BOTH_EMPTY) != BOTH_EMPTY) + +#if 0 +static inline void serial_echo(int ch) +{ + int lsr; + WAIT_FOR_XMITR; + serial_echo_outb(ch, UART_TX); +} +static inline void serial_debug(int ch) +{ + serial_echo(ch); + serial_echo('\r'); + serial_echo('\n'); +} +#endif +#endif /* _LINUX_SERIAL_REG_H */ + |