diff options
Diffstat (limited to 'contrib/syslinux/latest/doc/sdi.txt')
-rw-r--r-- | contrib/syslinux/latest/doc/sdi.txt | 149 |
1 files changed, 0 insertions, 149 deletions
diff --git a/contrib/syslinux/latest/doc/sdi.txt b/contrib/syslinux/latest/doc/sdi.txt deleted file mode 100644 index cf9b73f..0000000 --- a/contrib/syslinux/latest/doc/sdi.txt +++ /dev/null @@ -1,149 +0,0 @@ - SDI files - - -Syslinux supports SDI files ( *.sdi ). - -Features: - * Support for gzipped SDI images - * When used with gpxelinux.0, images can be downloaded by HTTP or FTP, - leading to fastest boot times. - -"System Deployment Image" is a file format created by Microsoft and mostly used -in its products to provide in a single file a boot loader, an OS loader -(like NTLDR) and a disk or partition image to boot from it without any -other installed program. This is typically used in a PXE environment to boot -embedded Windows versions without boot disk support. - -The support of SDI images in Syslinux is based on a white -paper from Saad Syed. You can find the paper here: - -http://msdn.microsoft.com/library/default.asp?url=/library/en-us/dnxpesp1/html/ram_sdi.asp - -SDI support has been only been tested with SDI v1.0 with Windows XP Embedded -images and may not work with later versions or alternative uses. - - - ++++ Supported SDI images ++++ - -To make a SDI image supported by pxelinux/isolinux/syslinux, you need to -follow the steps below (detailed instructions are in the white paper -cited above): - -You need to install "Windows Embedded Studio" and to run the -"Remote Boot Service Setup". - -1) Create a new SDI file (eg: sdimgr /new xpe.sdi). - -2) Before importing your target partition, add the following files -in the root folder: - * ntdetect.com - * boot.ini - Its content should be: - [boot loader] - default=ramdisk(0)\WINDOWS - [operating systems] - ramdisk(0)\WINDOWS="Windows XPE From RAM" /fastdetect -(you can customize the name and add options like /debug) - -Note: Your partition may be compressed (using compressed NTFS), but these two -files need to be uncompressed. - -3) Import the partition in the SDI file (eg: sdimgr xpe.sdi /readpart:D:). -The size of the partition must be less than 500 MB. - -4) Import the boot program STARTROM.COM -(eg: sdimgr xpe.sdi /import:BOOT,0,C:\Program Files\Windows Embedded\Remote Boot Service\Downloads\startrom.com) - -5) Import the nt loader NTLDR in the SDI file -(eg: sdimgr xpe.sdi /import:LOAD,0,C:\Program Files\Windows Embedded\Remote Boot Service\Downloads\ntldr) - -Note: only the version of NTLDR provided by Remote Boot Service Setup -and located in this directory has been tested. According to -"http://skolk.livejournal.com/667.html", "osloader.exe" from retail XP -can also be used to replace this NTLDR version. - -6) Pack the SDI file (eg: sdimgr xpe.sdi /pack) - -7) Gzip your image -If you want to speed the download time, you can gzip the image as it will -be uncompressed by syslinux during the loading. You can use some programs -like ntfsclone ("http://www.linux-ntfs.org/doku.php?id=ntfsclone") to -remove unused blocks from the NTFS filesystem before deploying your image. - -8) You are now ready to boot your image. -Unlike the traditional way of using SDI images (startrom.n12), you don't need -other files than your SDI image in the tftpboot (for pxelinux), the CD -(for isolinux), or the hard disk for syslinux. - -* You can use the usual options of pxelinux/isolinux/syslinux (config file, -config path, reboot time...) - -For example, a simple configuration with pxelinux: -/tftpboot/xpe.sdi -/tftpboot/pxelinux.0 -/tftpboot/pxelinux.cfg/default with the following content: - - DEFAULT 0 - label 0 [WinXpe] - KERNEL sdi.c32 - APPEND xpe.sdi - - - ++++ Error messages ++++ - -* No $SDI signature in file - A SDI image should begin by a signature "$SDI", the signature has not -been found in your file. Perhaps your file is corrupted or has not been created -correctly. Run sdimgr on it to see if everything is correct. - -* No BOOT BLOB in image - You have to import a boot program (eg: startrom.com) when you make -your SDI image (see above). The offset of this program in the SDI file -is in the SDI header (begining of the file). However, the offset -found in your SDI file is null. -You probably forgot to include the boot program. Run the sdimgr program -and look if you see a line like: -BOOT 0x00000000.00001000 0x00000000.00005EC2... - -------- - This is the - offset and - should not - be null - -* BOOT BLOB is empty - See above. The size of your boot program included in the SDI -is null. You probably imported a corrupted version of startrom.com. -Run sdimgr and check the size in the following line: -BOOT 0x00000000.00001000 0x00000000.00005EC2... - -------- - this is the - size and - should not - be null - -* BOOT BLOB extends beyond file - You have a BOOT BLOB in your SDI file, but its size is invalid -because its goes beyond the total image size. Check the tools you used -to build the image file. - -* BOOT BLOB too large for memory - Your BOOT BLOB seems correct, however there is not enough memory -to load it. Increase your RAM or reduce the SDI size. This is a very -abnormal situation as the BOOT BLOB is usually very small. Your SDI -file might be corrupted. - -* Image too large for memory - Your SDI file seems correct, however there is not enough memory -to load it. Increase your RAM or reduce the SDI size. - -* SDI header is corrupted - Your SDI file seems correct, but its header contains a checksum -that is invalid. You most likely have a corrupted SDI file. - - - ++++ Warning messages ++++ - -* Warning: unknown SDI version -You are using a newer version of SDI than the one with which this program -has been tested. It may not work. Please give feedback and provide your -SDI version. |