/*
* ARC FPGA Platform support code
*
* Copyright (C) 2012 Synopsys, Inc. (www.synopsys.com)
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/types.h>
#include <linux/init.h>
#include <linux/device.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/console.h>
#include <linux/of_platform.h>
#include <asm/setup.h>
#include <asm/clk.h>
#include <asm/mach_desc.h>
#include <plat/memmap.h>
#include <plat/smp.h>
#include <plat/irq.h>
/*-----------------------BVCI Latency Unit -----------------------------*/
#ifdef CONFIG_ARC_HAS_BVCI_LAT_UNIT
int lat_cycles = CONFIG_BVCI_LAT_CYCLES;
/* BVCI Bus Profiler: Latency Unit */
static void __init setup_bvci_lat_unit(void)
{
#define MAX_BVCI_UNITS 12
unsigned int i;
unsigned int *base = (unsigned int *)BVCI_LAT_UNIT_BASE;
const unsigned long units_req = CONFIG_BVCI_LAT_UNITS;
const unsigned int REG_UNIT = 21;
const unsigned int REG_VAL = 22;
/*
* There are multiple Latency Units corresponding to the many
* interfaces of the system bus arbiter (both CPU side as well as
* the peripheral side).
*
* Unit 0 - System Arb and Mem Controller - adds latency to all
* memory trasactions
* Unit 1 - I$ and System Bus
* Unit 2 - D$ and System Bus
* ..
* Unit 12 - IDE Disk controller and System Bus
*
* The programmers model requires writing to lat_unit reg first
* and then the latency value (cycles) to lat_value reg
*/
if (CONFIG_BVCI_LAT_UNITS == 0) {
writel(0, base + REG_UNIT);
writel(lat_cycles, base + REG_VAL);
pr_info("BVCI Latency for all Memory Transactions %d cycles\n",
lat_cycles);
} else {
for_each_set_bit(i, &units_req, MAX_BVCI_UNITS) {
writel(i + 1, base + REG_UNIT); /* loop is 0 based */
writel(lat_cycles, base + REG_VAL);
pr_info("BVCI Latency for Unit[%d] = %d cycles\n",
(i + 1), lat_cycles);
}
}
}
#else
static void __init setup_bvci_lat_unit(void)
{
}
#endif
/*----------------------- Platform Devices -----------------------------*/
#if IS_ENABLED(CONFIG_SERIAL_ARC)
static unsigned long arc_uart_info[] = {
0, /* uart->is_emulated (runtime @running_on_hw) */
0, /* uart->port.uartclk */
0, /* uart->baud */
0
};
#if defined(CONFIG_SERIAL_ARC_CONSOLE)
/*
* static platform data - but only for early serial
* TBD: derive this from a special DT node
*/
static struct resource arc_uart0_res[] = {
{
.start = UART0_BASE,
.end = UART0_BASE + 0xFF,
.flags = IORESOURCE_MEM,
},
{
.start = UART0_IRQ,
.end = UART0_IRQ,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device arc_uart0_dev = {
.name = "arc-uart",
.id = 0,
.num_resources = ARRAY_SIZE(arc_uart0_res),
.resource = arc_uart0_res,
.dev = {
.platform_data = &arc_uart_info,
},
};
static struct platform_device *fpga_early_devs[] __initdata = {
&arc_uart0_dev,
};
#endif /* CONFIG_SERIAL_ARC_CONSOLE */
static void arc_fpga_serial_init(void)
{
/* To let driver workaround ISS bug: baudh Reg can't be set to 0 */
arc_uart_info[0] = !running_on_hw;
arc_uart_info[1] = arc_get_core_freq();
arc_uart_info[2] = CONFIG_ARC_SERIAL_BAUD;
#if defined(CONFIG_SERIAL_ARC_CONSOLE)
early_platform_add_devices(fpga_early_devs,
ARRAY_SIZE(fpga_early_devs));
/*
* ARC console driver registers itself as an early platform driver
* of class "earlyprintk".
* Install it here, followed by probe of devices.
* The installation here doesn't require earlyprintk in command line
* To do so however, replace the lines below with
* parse_early_param();
* early_platform_driver_probe("earlyprintk", 1, 1);
* ^^
*/
early_platform_driver_register_all("earlyprintk");
early_platform_driver_probe("earlyprintk", 1, 0);
/*
* This is to make sure that arc uart would be preferred console
* despite one/more of following:
* -command line lacked "console=ttyARC0" or
* -CONFIG_VT_CONSOLE was enabled (for no reason whatsoever)
* Note that this needs to be done after above early console is reg,
* otherwise the early console never gets a chance to run.
*/
add_preferred_console("ttyARC", 0, "115200");
#endif /* CONFIG_SERIAL_ARC_CONSOLE */
}
#else /* !IS_ENABLED(CONFIG_SERIAL_ARC) */
static void arc_fpga_serial_init(void)
{
}
#endif
static void __init plat_fpga_early_init(void)
{
pr_info("[plat-arcfpga]: registering early dev resources\n");
setup_bvci_lat_unit();
arc_fpga_serial_init();
#ifdef CONFIG_SMP
iss_model_init_early_smp();
#endif
}
static struct of_dev_auxdata plat_auxdata_lookup[] __initdata = {
#if IS_ENABLED(CONFIG_SERIAL_ARC)
OF_DEV_AUXDATA("snps,arc-uart", UART0_BASE, "arc-uart", arc_uart_info),
#endif
{}
};
static void __init plat_fpga_populate_dev(void)
{
pr_info("[plat-arcfpga]: registering device resources\n");
/*
* Traverses flattened DeviceTree - registering platform devices
* complete with their resources
*/
of_platform_populate(NULL, of_default_bus_match_table,
plat_auxdata_lookup, NULL);
}
/*----------------------- Machine Descriptions ------------------------------
*
* Machine description is simply a set of platform/board specific callbacks
* This is not directly related to DeviceTree based dynamic device creation,
* however as part of early device tree scan, we also select the right
* callback set, by matching the DT compatible name.
*/
static const char *aa4_compat[] __initdata = {
"snps,arc-angel4",
NULL,
};
MACHINE_START(ANGEL4, "angel4")
.dt_compat = aa4_compat,
.init_early = plat_fpga_early_init,
.init_machine = plat_fpga_populate_dev,
.init_irq = plat_fpga_init_IRQ,
#ifdef CONFIG_SMP
.init_smp = iss_model_init_smp,
#endif
MACHINE_END
static const char *ml509_compat[] __initdata = {
"snps,arc-ml509",
NULL,
};
MACHINE_START(ML509, "ml509")
.dt_compat = ml509_compat,
.init_early = plat_fpga_early_init,
.init_machine = plat_fpga_populate_dev,
.init_irq = plat_fpga_init_IRQ,
#ifdef CONFIG_SMP
.init_smp = iss_model_init_smp,
#endif
MACHINE_END
static const char *nsimosci_compat[] __initdata = {
"snps,nsimosci",
NULL,
};
MACHINE_START(NSIMOSCI, "nsimosci")
.dt_compat = nsimosci_compat,
.init_early = NULL,
.init_machine = plat_fpga_populate_dev,
.init_irq = NULL,
MACHINE_END
