/*
* based on code from the following
* Copyright 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
* Copyright 2009-2010 Pegatron Corporation. All Rights Reserved.
* Copyright 2009-2010 Genesi USA, Inc. All Rights Reserved.
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/gpio.h>
#include <linux/leds.h>
#include <linux/input.h>
#include <linux/delay.h>
#include <linux/io.h>
#include <linux/fsl_devices.h>
#include <linux/spi/flash.h>
#include <linux/spi/spi.h>
#include <mach/common.h>
#include <mach/hardware.h>
#include <mach/iomux-mx51.h>
#include <mach/i2c.h>
#include <mach/mxc_ehci.h>
#include <asm/irq.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include "devices-imx51.h"
#include "devices.h"
#include "efika.h"
#define MX51_USB_PLL_DIV_24_MHZ 0x01
#define EFIKAMX_SPI_CS0 IMX_GPIO_NR(4, 24)
#define EFIKAMX_SPI_CS1 IMX_GPIO_NR(4, 25)
static iomux_v3_cfg_t mx51efika_pads[] = {
/* UART1 */
MX51_PAD_UART1_RXD__UART1_RXD,
MX51_PAD_UART1_TXD__UART1_TXD,
MX51_PAD_UART1_RTS__UART1_RTS,
MX51_PAD_UART1_CTS__UART1_CTS,
/* SD 1 */
MX51_PAD_SD1_CMD__SD1_CMD,
MX51_PAD_SD1_CLK__SD1_CLK,
MX51_PAD_SD1_DATA0__SD1_DATA0,
MX51_PAD_SD1_DATA1__SD1_DATA1,
MX51_PAD_SD1_DATA2__SD1_DATA2,
MX51_PAD_SD1_DATA3__SD1_DATA3,
/* SD 2 */
MX51_PAD_SD2_CMD__SD2_CMD,
MX51_PAD_SD2_CLK__SD2_CLK,
MX51_PAD_SD2_DATA0__SD2_DATA0,
MX51_PAD_SD2_DATA1__SD2_DATA1,
MX51_PAD_SD2_DATA2__SD2_DATA2,
MX51_PAD_SD2_DATA3__SD2_DATA3,
/* SD/MMC WP/CD */
MX51_PAD_GPIO1_0__SD1_CD,
MX51_PAD_GPIO1_1__SD1_WP,
MX51_PAD_GPIO1_7__SD2_WP,
MX51_PAD_GPIO1_8__SD2_CD,
/* spi */
MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI,
MX51_PAD_CSPI1_MISO__ECSPI1_MISO,
MX51_PAD_CSPI1_SS0__GPIO4_24,
MX51_PAD_CSPI1_SS1__GPIO4_25,
MX51_PAD_CSPI1_RDY__ECSPI1_RDY,
MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK,
};
/* Serial ports */
static const struct imxuart_platform_data uart_pdata = {
.flags = IMXUART_HAVE_RTSCTS,
};
/* This function is board specific as the bit mask for the plldiv will also
* be different for other Freescale SoCs, thus a common bitmask is not
* possible and cannot get place in /plat-mxc/ehci.c.
*/
static int initialize_otg_port(struct platform_device *pdev)
{
u32 v;
void __iomem *usb_base;
void __iomem *usbother_base;
usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K);
if (!usb_base)
return -ENOMEM;
usbother_base = (void __iomem *)(usb_base + MX5_USBOTHER_REGS_OFFSET);
/* Set the PHY clock to 19.2MHz */
v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK;
v |= MX51_USB_PLL_DIV_24_MHZ;
__raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
iounmap(usb_base);
mdelay(10);
return mx51_initialize_usb_hw(0, MXC_EHCI_INTERNAL_PHY);
}
static struct mxc_usbh_platform_data dr_utmi_config = {
.init = initialize_otg_port,
.portsc = MXC_EHCI_UTMI_16BIT,
};
static struct mtd_partition mx51_efika_spi_nor_partitions[] = {
{
.name = "u-boot",
.offset = 0,
.size = SZ_256K,
},
{
.name = "config",
.offset = MTDPART_OFS_APPEND,
.size = SZ_64K,
},
};
static struct flash_platform_data mx51_efika_spi_flash_data = {
.name = "spi_flash",
.parts = mx51_efika_spi_nor_partitions,
.nr_parts = ARRAY_SIZE(mx51_efika_spi_nor_partitions),
.type = "sst25vf032b",
};
static struct spi_board_info mx51_efika_spi_board_info[] __initdata = {
{
.modalias = "m25p80",
.max_speed_hz = 25000000,
.bus_num = 0,
.chip_select = 1,
.platform_data = &mx51_efika_spi_flash_data,
.irq = -1,
},
};
static int mx51_efika_spi_cs[] = {
EFIKAMX_SPI_CS0,
EFIKAMX_SPI_CS1,
};
static const struct spi_imx_master mx51_efika_spi_pdata __initconst = {
.chipselect = mx51_efika_spi_cs,
.num_chipselect = ARRAY_SIZE(mx51_efika_spi_cs),
};
void __init efika_board_common_init(void)
{
mxc_iomux_v3_setup_multiple_pads(mx51efika_pads,
ARRAY_SIZE(mx51efika_pads));
mxc_register_device(&mxc_usbdr_host_device, &dr_utmi_config);
imx51_add_imx_uart(0, &uart_pdata);
imx51_add_sdhci_esdhc_imx(0, NULL);
spi_register_board_info(mx51_efika_spi_board_info,
ARRAY_SIZE(mx51_efika_spi_board_info));
imx51_add_ecspi(0, &mx51_efika_spi_pdata);
}
