/*
* arch/arm/plat-omap/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for OMAP-based platforms
*
* Copyright (C) 2009 Texas Instruments
* Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#include <mach/hardware.h>
#include <mach/io.h>
#include <mach/irqs.h>
#include <asm/hardware/gic.h>
#include <plat/omap24xx.h>
#include <plat/omap34xx.h>
#include <plat/omap44xx.h>
#include <plat/multi.h>
#define OMAP2_IRQ_BASE OMAP2_L4_IO_ADDRESS(OMAP24XX_IC_BASE)
#define OMAP3_IRQ_BASE OMAP2_L4_IO_ADDRESS(OMAP34XX_IC_BASE)
#define OMAP4_IRQ_BASE OMAP2_L4_IO_ADDRESS(OMAP44XX_GIC_CPU_BASE)
#define INTCPS_SIR_IRQ_OFFSET 0x0040 /* omap2/3 active interrupt offset */
#define ACTIVEIRQ_MASK 0x7f /* omap2/3 active interrupt bits */
.macro disable_fiq
.endm
.macro arch_ret_to_user, tmp1, tmp2
.endm
/*
* Unoptimized irq functions for multi-omap2, 3 and 4
*/
#ifdef MULTI_OMAP2
/*
* We use __glue to avoid errors with multiple definitions of
* .globl omap_irq_base as it's included from entry-armv.S but not
* from entry-common.S.
*/
#ifdef __glue
.pushsection .data
.globl omap_irq_base
omap_irq_base:
.word 0
.popsection
#endif
/*
* Configure the interrupt base on the first interrupt.
* See also omap_irq_base_init for setting omap_irq_base.
*/
.macro get_irqnr_preamble, base, tmp
ldr \base, =omap_irq_base @ irq base address
ldr \base, [\base, #0] @ irq base value
.endm
/* Check the pending interrupts. Note that base already set */
.macro get_irqnr_and_base, irqnr, irqstat, base, tmp
tst \base, #0x100 @ gic address?
bne 4401f @ found gic
/* Handle omap2 and omap3 */
ldr \irqnr, [\base, #0x98] /* IRQ pending reg 1 */
cmp \irqnr, #0x0
bne 9998f
ldr \irqnr, [\base, #0xb8] /* IRQ pending reg 2 */
cmp \irqnr, #0x0
bne 9998f
ldr \irqnr, [\base, #0xd8] /* IRQ pending reg 3 */
cmp \irqnr, #0x0
9998:
ldrne \irqnr, [\base, #INTCPS_SIR_IRQ_OFFSET]
and \irqnr, \irqnr, #ACTIVEIRQ_MASK /* Clear spurious bits */
b 9999f
/* Handle omap4 */
4401: ldr \irqstat, [\base, #GIC_CPU_INTACK]
ldr \tmp, =1021
bic \irqnr, \irqstat, #0x1c00
cmp \irqnr, #29
cmpcc \irqnr, \irqnr
cmpne \irqnr, \tmp
cmpcs \irqnr, \irqnr
9999:
.endm
#ifdef CONFIG_SMP
/* We assume that irqstat (the raw value of the IRQ acknowledge
* register) is preserved from the macro above.
* If there is an IPI, we immediately signal end of interrupt
* on the controller, since this requires the original irqstat
* value which we won't easily be able to recreate later.
*/
.macro test_for_ipi, irqnr, irqstat, base, tmp
bic \irqnr, \irqstat, #0x1c00
cmp \irqnr, #16
it cc
strcc \irqstat, [\base, #GIC_CPU_EOI]
it cs
cmpcs \irqnr, \irqnr
.endm
/* As above, this assumes that irqstat and base are preserved */
.macro test_for_ltirq, irqnr, irqstat, base, tmp
bic \irqnr, \irqstat, #0x1c00
mov \tmp, #0
cmp \irqnr, #29
itt eq
moveq \tmp, #1
streq \irqstat, [\base, #GIC_CPU_EOI]
cmp \tmp, #0
.endm
#endif /* CONFIG_SMP */
#else /* MULTI_OMAP2 */
/*
* Optimized irq functions for omap2, 3 and 4
*/
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
.macro get_irqnr_preamble, base, tmp
#ifdef CONFIG_ARCH_OMAP2
ldr \base, =OMAP2_IRQ_BASE
#else
ldr \base, =OMAP3_IRQ_BASE
#endif
.endm
/* Check the pending interrupts. Note that base already set */
.macro get_irqnr_and_base, irqnr, irqstat, base, tmp
ldr \irqnr, [\base, #0x98] /* IRQ pending reg 1 */
cmp \irqnr, #0x0
bne 9999f
ldr \irqnr, [\base, #0xb8] /* IRQ pending reg 2 */
cmp \irqnr, #0x0
bne 9999f
ldr \irqnr, [\base, #0xd8] /* IRQ pending reg 3 */
cmp \irqnr, #0x0
9999:
ldrne \irqnr, [\base, #INTCPS_SIR_IRQ_OFFSET]
and \irqnr, \irqnr, #ACTIVEIRQ_MASK /* Clear spurious bits */
.endm
#endif
#ifdef CONFIG_ARCH_OMAP4
#define HAVE_GET_IRQNR_PREAMBLE
#include <asm/hardware/entry-macro-gic.S>
.macro get_irqnr_preamble, base, tmp
ldr \base, =OMAP4_IRQ_BASE
.endm
#endif
#endif /* MULTI_OMAP2 */
.macro irq_prio_table
.endm
